Skip to content

A python implementation of the HomeKit Accessory Protocol (HAP)

License

Notifications You must be signed in to change notification settings

padalev/HAP-python

 
 

Repository files navigation

PyPI version Build Status codecov Python Versions Documentation Status Downloads

HAP-python

HomeKit Accessory Protocol implementation in python 3. With this project, you can integrate your own smart devices and add them to your iOS Home app. Since Siri is integrated with the Home app, you can start voice-control your accessories right away.

Main features:

  • Camera - HAP-python supports the camera accessory from version 2.3.0!
  • asyncio support - You can run various tasks or accessories in the event loop.
  • Out of the box support for Apple-defined services - see them in the resources folder.
  • Secure pairing by just scanning the QR code.
  • Integrated with the home automation framework Home Assistant.

The project was developed for a Raspberry Pi, but it should work on other platforms. To kick-start things, you can open main.py or busy_home.py, where you will find some fake accessories. Just run one of them, for example python3 busy_home.py, and you can add it in the Home app (be sure to be in the same network). Stop it by hitting Ctrl+C.

There are example accessories as well as integrations with real products in the accessories folder. See how to configure your camera in camera_main.py.

Table of Contents

  1. API
  2. Installation
  3. Setting up a camera
  4. Run at boot (and a Switch to shutdown your device)
  5. Notice

Installation

As of version 3.5.1, HAP-python no longer supports python older than 3.6, because we are moving to asyncio. If your platform does not have a compatible python out of the box, you can install it manually or just use an older version of HAP-python.

As a prerequisite, you will need Avahi/Bonjour installed (due to zeroconf package). On a Raspberry Pi, you can get it with:

$ sudo apt-get install libavahi-compat-libdnssd-dev

avahi-utils may also fit the bill. Then, you can install with pip3 (you will need sudo or --user for the install):

$ pip3 install HAP-python[QRCode]

This will install HAP-python in your python packages, so that you can import it as pyhap. To uninstall, just do:

$ pip3 uninstall HAP-python

API

A typical flow for using HAP-python starts with implementing an Accessory. This is done by subclassing Accessory and putting in place a few details (see below). After that, you give your accessory to an AccessoryDriver to manage. This will take care of advertising it on the local network, setting a HAP server and running the Accessory. Take a look at main.py for a quick start on that.

"""An example of how to setup and start an Accessory.
This is:
1. Create the Accessory object you want.
2. Add it to an AccessoryDriver, which will advertise it on the local network,
    setup a server to answer client queries, etc.
"""
import logging
import signal
import random

from pyhap.accessory import Accessory, Bridge
from pyhap.accessory_driver import AccessoryDriver
import pyhap.loader as loader
from pyhap import camera
from pyhap.const import CATEGORY_SENSOR

logging.basicConfig(level=logging.INFO, format="[%(module)s] %(message)s")


class TemperatureSensor(Accessory):
    """Fake Temperature sensor, measuring every 3 seconds."""

    category = CATEGORY_SENSOR

    def __init__(self, *args, **kwargs):
        super().__init__(*args, **kwargs)

        serv_temp = self.add_preload_service('TemperatureSensor')
        self.char_temp = serv_temp.configure_char('CurrentTemperature')

    @Accessory.run_at_interval(3)
    async def run(self):
        self.char_temp.set_value(random.randint(18, 26))


def get_bridge(driver):
    """Call this method to get a Bridge instead of a standalone accessory."""
    bridge = Bridge(driver, 'Bridge')
    temp_sensor = TemperatureSensor(driver, 'Sensor 2')
    temp_sensor2 = TemperatureSensor(driver, 'Sensor 1')
    bridge.add_accessory(temp_sensor)
    bridge.add_accessory(temp_sensor2)

    return bridge


def get_accessory(driver):
    """Call this method to get a standalone Accessory."""
    return TemperatureSensor(driver, 'MyTempSensor')


# Start the accessory on port 51826
driver = AccessoryDriver(port=51826)

# Change `get_accessory` to `get_bridge` if you want to run a Bridge.
driver.add_accessory(accessory=get_accessory(driver))

# We want SIGTERM (terminate) to be handled by the driver itself,
# so that it can gracefully stop the accessory, server and advertising.
signal.signal(signal.SIGTERM, driver.signal_handler)

# Start it!
driver.start()

Service Callbacks

When you are working with tightly coupled characteristics such as "On" and "Brightness," you may need to use a service callback to receive all changes in a single request.

With characteristic callbacks, you do now know that a "Brightness" characteristic is about to be processed right after an "On" and may end up setting a LightBulb to 100% and then dim it back down to the expected level.

from pyhap.accessory import Accessory
from pyhap.const import Category
import pyhap.loader as loader

class Light(Accessory):
    """Implementation of a mock light accessory."""

    category = Category.CATEGORY_LIGHTBULB  # This is for the icon in the iOS Home app.

    def __init__(self, *args, **kwargs):
        """Here, we just store a reference to the on and brightness characteristics and
        add a method that will be executed every time their value changes.
        """
        # If overriding this method, be sure to call the super's implementation first.
        super().__init__(*args, **kwargs)

        # Add the services that this Accessory will support with add_preload_service here
        serv_light = self.add_preload_service('Lightbulb')
        self.char_on = serv_light.configure_char('On', value=self._state)
        self.char_brightness = serv_light.configure_char('Brightness', value=100)

        serv_light.setter_callback = self._set_chars

    def _set_chars(self, char_values):
        """This will be called every time the value of the on of the
        characteristics on the service changes.
        """
        if "On" in char_values:
            print('On changed to: ', char_values["On"])
        if "Brightness" in char_values:
            print('Brightness changed to: ', char_values["Brightness"])

    @Acessory.run_at_interval(3)  # Run this method every 3 seconds
    # The `run` method can be `async` as well
    def run(self):
        """We override this method to implement what the accessory will do when it is
        started.

        We set the current temperature to a random number. The decorator runs this method
        every 3 seconds.
        """
        self.char_on.set_value(random.randint(0, 1))
        self.char_brightness.set_value(random.randint(1, 100))

    # The `stop` method can be `async` as well
    def stop(self):
        """We override this method to clean up any resources or perform final actions, as
        this is called by the AccessoryDriver when the Accessory is being stopped.
        """
        print('Stopping accessory.')

Setting up a camera

The Camera accessory implements the HomeKit Protocol for negotiating stream settings, such as the picture width and height, number of audio channels and others. Starting a video and/or audio stream is very platform specific. Because of this, you need to figure out what video and audio settings your camera supports and set them in the options parameter that is passed to the Camera Accessory. Refer to the documentation for the Camera contructor for the settings you need to specify.

By default, HAP-python will execute the ffmpeg command with the negotiated parameters when the stream should be started and will terminate the started process when the stream should be stopped (see the default: Camera.FFMPEG_CMD). If the default command is not supported or correctly formatted for your platform, the streaming can fail.

For these cases, HAP-python has hooks so that you can insert your own command or implement the logic for starting or stopping the stream. There are two options:

  1. Pass your own command that will be executed when the stream should be started.

    You pass the command as a value to the key start_stream_cmd in the options parameter to the constuctor of the Camera Accessory. The command is formatted using the negotiated stream configuration parameters. For example, if the negotiated width is 640 and you pass foo start -width {width}, the command will be formatted as foo start -width 640.

    The full list of negotiated stream configuration parameters can be found in the documentation for the Camera.start method.

  2. Implement your own logic to start, stop and reconfigure the stream.

    If you need more flexibility in managing streams, you can directly implement the Camera methods start, stop and reconfigure. Each will be called when the stream should be respectively started, stopped or reconfigured. The start and reconfigure methods are given the negotiated stream configuration parameters.

    Have a look at the documentation of these methods for more information.

Finally, if you can take snapshots from the camera, you may want to implement the Camera.snapshot method. By default, this serves a stock photo.

Run at boot

This is a quick way to get HAP-python to run at boot on a Raspberry Pi. It is recommended to turn on "Wait for network" in raspi-config. If this turns to be unreliable, see this.

Copy the below in /etc/systemd/system/HAP-python.service (needs sudo).

[Unit]
Description = HAP-python daemon
Wants = pigpiod.service  # Remove this if you don't depend on pigpiod
After = local-fs.target network-online.target pigpiod.service

[Service]
User = lesserdaemon  # It's a good idea to use some unprivileged system user
# Script starting HAP-python, e.g. main.py
# Be careful to set any paths you use, e.g. for persisting the state.
ExecStart = /usr/bin/python3 /home/lesserdaemon/.hap-python/hap-python.py

[Install]
WantedBy = multi-user.target

Test that everything is fine by doing:

> sudo systemctl start HAP-python
> systemctl status HAP-python
> sudo journalctl -u HAP-python  # to see the output of the start up script.
> sudo systemctl stop HAP-python

To enable or disable at boot, do:

> sudo systemctl enable HAP-python
> sudo systemctl disable HAP-python

Shutdown switch

If you are running HAP-python on a Raspberry Pi, you may want to add a Shutdown Switch to your Home. This is a Switch Accessory, which, when triggered, executes sudo shutdown -h now, i.e. it shutdowns and halts the Pi. This allows you to safely unplug it.

For the above to work, you need to enable passwordless /sbin/shutdown to whichever user is running HAP-python. For example, do:

$ sudo visudo # and add the line: "<hap-user> ALL=NOPASSWD: /sbin/shutdown".

Notice

Some HAP know-how was taken from HAP-NodeJS by KhaosT.

I am not aware of any bugs, but I am more than confident that such exist. If you find any, please report and I will try to fix them.

Suggestions are always welcome.

Have fun!

About

A python implementation of the HomeKit Accessory Protocol (HAP)

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • Python 99.7%
  • Shell 0.3%