mediatek: filogic: Add support for Wavlink WL-WN586X3

Hardware -------- - SOC: MediaTek MT7981 - ram: 256MB DDR3 - FLASH: 16MB SPI-NOR - Ethernet: 2x1Gb Lan 1x1Gb Wan - WIFI: MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4/5) - LEDs: 2xLan 1x Wan 1x WIFI 1xSTATUS MAC table, same as stock firmware: LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII) WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII) 2G: 80:3F:5D:xx:xx:x3 partition "factory" at 0x4 (binary), on label 5G: 80:3F:5D:xx:xx:x3 Same as 2G Installation Method 1: ssh -------------------------- 1. Connect PC to the lan port. Set the PC IP to 192.168.10.100 if required. 2. Navigate to http://192.168.10.1/ 3. Log into the Wavlink WebGUI. Default username/password is admin/admin. 4. Use WebGUI to upgrade the firmware to WAVLINK_WN586X3-A_M86X3A_V240113_WO-GDBYFM-modified.bin downloaded from https://github.com/themaverickdm/firmware-misc/tree/main/wavlink/wl-wn586x3 Warning: All settings will be lost! 5. Wait about 5 minutes, and after flashing is completed, log into the router using (with admin123 as password): ssh [email protected] 6. scp the openwrt image file onto the router, usually under /tmp somewhere. openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin 7. Flash openwrt image file like so: mtd write \ openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin \ firmware Warning: Previous firmware will be overwritten! 8. Wait about 5 minutes, and after the flashing is completed, set the PC IP to 192.168.1.100 if required and log into the router like so: ssh [email protected] Installation Method 2: u-boot ----------------------------- 1. Connect UART: TX-> 586X3 RX, RX-> 586X3 TX, GND-> 586 GND. 2. Connect PC to the wan (not lan!) port. 3. Setup the tftp server on PC, set IP to 192.168.10.100, 4. Power on the device. Select '2' to upgrade firmware in Uboot. 5. Input the image name and start to upgrade. Uboot console log: CPU: MediaTek MT7981 Model: mt7981-rfb DRAM: 256 MiB Core: 34 devices, 13 uclasses, devicetree: embed Loading Environment from nowhere... OK In: serial@11002000 Out: serial@11002000 Err: serial@11002000 Net: Warning: ethernet@15100000 (eth0) using random MAC address - 02:47:fb:b2:53:2d eth0: ethernet@15100000 UBOOT WN586X3A gpio: pin 9 (gpio 9) value is 0 gpio: pin 10 (gpio 10) value is 0 gpio: pin 5 (gpio 5) value is 0 gpio: pin 12 (gpio 12) value is 0 gpio: pin 13 (gpio 13) value is 0 *** U-Boot Boot Menu *** 1. Startup system (Default) 2. Upgrade firmware 3. Upgrade ATF BL2 4. Upgrade ATF FIP 5. Upgrade single image 6. Load image 0. U-Boot console Co-authored-by: R Maru <[email protected]> Signed-off-by: R Maru <[email protected]> Signed-off-by: Sijia Huang <[email protected]>
lede-project · Jun 9, 2024 · 33db914 · 33db914
1 parent dd6bbba
commit 33db914
Show file tree

Hide file tree

Showing 4 changed files with 287 additions and 1 deletion.
diff --git a/target/linux/mediatek/dts/mt7981b-wavlink-wl-wn586x3.dts b/target/linux/mediatek/dts/mt7981b-wavlink-wl-wn586x3.dts
@@ -0,0 +1,270 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include "mt7981.dtsi"
+
+/ {
+	model = "WAVLINK WL-WN586X3";
+	compatible = "wavlink,wl-wn586x3", "mediatek,mt7981";
+
+	aliases {
+		label-mac-device = &wifi;
+		led-boot = &led_status_blue;
+		led-failsafe = &led_status_blue;
+		led-running = &led_status_blue;
+		led-upgrade = &led_status_blue;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&pio 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_WAN;
+			gpios = <&pio 5 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_WLAN;
+			gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "phy1tpt";
+		};
+
+		led_status_blue: led-2 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led-3 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <1>;
+			gpios = <&pio 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-4 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_LAN;
+			function-enumerator = <2>;
+			gpios = <&pio 13 GPIO_ACTIVE_LOW>;
+		};
+
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+		nvmem-cells = <&macaddr_hw_44e 0>;
+		nvmem-cell-names = "mac-address";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	gmac1: mac@1 {
+		compatible = "mediatek,eth-mac";
+		reg = <1>;
+		phy-mode = "gmii";
+		phy-handle = <&int_gbe_phy>;
+		nvmem-cells = <&macaddr_hw_44e 1>;
+		nvmem-cell-names = "mac-address";
+	};
+};
+
+&mdio_bus {
+	switch: switch@1f {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_flash_pins>;
+	status = "disabled";
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_flash_pins>;
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+
+		spi-max-frequency = <25000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@00000 {
+				label = "bl2";
+				reg = <0x00000 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "u-boot-env";
+				reg = <0x40000 0x10000>;
+				read-only;
+			};
+
+			factory: partition@50000 {
+				label = "factory";
+				reg = <0x50000 0xb0000>;
+				read-only;
+
+				nvmem-layout {
+					compatible = "fixed-layout";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					macaddr_factory_4: macaddr@4 {
+						compatible = "mac-base";
+						reg = <0x4 0x6>;
+						#nvmem-cell-cells = <1>;
+					};
+				};
+			};
+
+			partition@100000 {
+				label = "fip";
+				reg = <0x100000 0x80000>;
+				read-only;
+			};
+
+			partition@f0000 {
+				label = "firmware";
+				reg = <0x180000 0xe00000>;
+			};
+
+			partition@f80000 {
+				label = "hw";
+				reg = <0xf80000 0x80000>;
+
+				nvmem-layout {
+					compatible = "fixed-layout";
+					#address-cells = <1>;
+					#size-cells = <1>;
+
+					macaddr_hw_44e: macaddr@44e {
+						compatible = "mac-base";
+						reg = <0x44e 0x11>;
+						#nvmem-cell-cells = <1>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&pio {
+	spi0_flash_pins: spi0-pins {
+		mux {
+			function = "spi";
+			groups = "spi0", "spi0_wp_hold";
+		};
+	};
+
+	spi2_flash_pins: spi2-pins {
+		mux {
+			function = "spi";
+			groups = "spi2", "spi2_wp_hold";
+		};
+
+		conf-pu {
+			pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+			drive-strength = <8>;
+			bias-pull-up = <103>;
+		};
+
+		conf-pd {
+			pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+			drive-strength = <8>;
+			bias-pull-down = <103>;
+		};
+	};
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@1 {
+			reg = <1>;
+			label = "lan2";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan1";
+		};
+
+		port@6 {
+			reg = <6>;
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&wifi {
+	status = "okay";
+	mediatek,mtd-eeprom = <&factory 0x0>;
+	nvmem-cells = <&macaddr_factory_4 0>;
+	nvmem-cell-names = "mac-address";
+};
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
@@ -91,6 +91,10 @@ smartrg,sdg-8734)
 	ucidef_set_led_netdev "wan-green" "WAN" "mdio-bus:00:green:wan" "wan" "link_2500 link_5000"
 	ucidef_set_led_netdev "wan-orange" "WAN" "mdio-bus:00:orange:wan" "wan" "link_100 link_1000"
 	ucidef_set_led_netdev "wan-white" "WAN" "mdio-bus:00:white:wan" "wan" "link_10000"
+wavlink,wl-wn586x3)
+	ucidef_set_led_netdev "lan-1" "lan-1" "blue:lan-1" "lan1" "link tx rx"
+	ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-2" "lan2" "link tx rx"
+	ucidef_set_led_netdev "wan" "wan" "blue:wan" "eth1" "link tx rx"
 	;;
 xiaomi,mi-router-wr30u-stock|\
 xiaomi,mi-router-wr30u-ubootmod)

diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network
@@ -96,7 +96,8 @@ mediatek_setup_interfaces()
 	yuncore,ax835)
 		ucidef_set_interfaces_lan_wan lan wan
 		;;
-	tplink,tl-xdr6086)
+	tplink,tl-xdr6086|\
+	wavlink,wl-wn586x3)
 		ucidef_set_interfaces_lan_wan "lan1 lan2" eth1
 		;;
 	xiaomi,mi-router-ax3000t|\

diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk
@@ -1161,6 +1161,17 @@ define Device/unielec_u7981-01-nand
 endef
 TARGET_DEVICES += unielec_u7981-01-nand
 
+define Device/wavlink_wl-wn586x3
+  DEVICE_VENDOR := WAVLINK
+  DEVICE_MODEL := WL-WN586X3
+  DEVICE_DTS := mt7981b-wavlink-wl-wn586x3
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_DTS_LOADADDR := 0x47000000
+  IMAGE_SIZE := 15424k
+  DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
+endef
+TARGET_DEVICES += wavlink_wl-wn586x3
+
 define Device/xiaomi_mi-router-ax3000t
   DEVICE_VENDOR := Xiaomi
   DEVICE_MODEL := Mi Router AX3000T