eeprom: at24: Simplify WP management and make it optional #6

bthebaudeau · 2017-11-13T15:17:23Z

The WP management introduced by Amlogic was uselessly complicated. It was also silently mandatory, which caused the following error without a WP-control GPIO:

[    1.972520@0] faild to get write interval time !
[    1.977044@0] faild to get write interval time !
[    1.981698@0] ------------[ cut here ]------------
[    1.986505@0] WARNING: CPU: 0 PID: 1 at /home/terry/project/vim/nougat/common/drivers/gpio/gpiolib.c:159 gpio_to_desc+0x58/0x60()
[    1.998257@0] invalid GPIO -1514520
[    2.001731@0] Modules linked in:
[    2.004961@0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.29-g576a041-dirty #14
[    2.012575@0] Call trace:
[    2.015201@0] [<ffffffc001088fe8>] dump_backtrace+0x0/0x140
[    2.020830@0] [<ffffffc001089148>] show_stack+0x20/0x2c
[    2.026046@0] [<ffffffc001b17acc>] dump_stack+0x74/0xc0
[    2.031302@0] [<ffffffc00109eaa0>] warn_slowpath_common+0x90/0xb8
[    2.037438@0] [<ffffffc00109eb3c>] warn_slowpath_fmt+0x74/0x88
[    2.043290@0] [<ffffffc00143b73c>] gpio_to_desc+0x54/0x60
[    2.048706@0] [<ffffffc00143c430>] gpio_request+0x20/0x38
[    2.054157@0] [<ffffffc0014a5130>] at24_wp_enable+0x30/0x78
[    2.059731@0] [<ffffffc0014a558c>] at24_dt_parse+0x9c/0x110
[    2.065338@0] [<ffffffc0014a5914>] at24_probe+0x314/0x584
[    2.070782@0] [<ffffffc00159d560>] i2c_device_probe+0xa0/0xe4
[    2.076533@0] [<ffffffc001485d08>] really_probe+0x74/0x240
[    2.082051@0] [<ffffffc00148600c>] __driver_attach+0xb0/0xb8
[    2.087749@0] [<ffffffc001483e54>] bus_for_each_dev+0x68/0xac
[    2.093513@0] [<ffffffc001485810>] driver_attach+0x2c/0x38
[    2.099019@0] [<ffffffc001485414>] bus_add_driver+0x158/0x210
[    2.104818@0] [<ffffffc0014867b0>] driver_register+0x6c/0x138
[    2.110575@0] [<ffffffc00159d3dc>] i2c_register_driver+0x3c/0xc0
[    2.116609@0] [<ffffffc001f66480>] at24_init+0x50/0x5c
[    2.121792@0] [<ffffffc0010816b8>] do_one_initcall+0xe0/0x12c
[    2.127546@0] [<ffffffc001f38924>] kernel_init_freeable+0x134/0x1d8
[    2.133851@0] [<ffffffc001b0f390>] kernel_init+0x1c/0xdc
[    2.139213@0] ---[ end trace c84d7b19dc3d49e2 ]---
[    2.144000@0] gpiod_request: invalid GPIO
[    2.148017@0] faild to alloc write protect (-1514520)!
[    2.153185@0] EEPROM_AT24c256
[    2.156086@0] write protect port level is -1514520[    2.160888@0] wp_port=-1514520 write_ops_interval=-64ms
[    2.166151@0] at24 2-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write

The WP management introduced by Amlogic was uselessly complicated. It was also silently mandatory, which caused the following error without a WP-control GPIO: [ 1.972520@0] faild to get write interval time ! [ 1.977044@0] faild to get write interval time ! [ 1.981698@0] ------------[ cut here ]------------ [ 1.986505@0] WARNING: CPU: 0 PID: 1 at /home/terry/project/vim/nougat/common/drivers/gpio/gpiolib.c:159 gpio_to_desc+0x58/0x60() [ 1.998257@0] invalid GPIO -1514520 [ 2.001731@0] Modules linked in: [ 2.004961@0] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.29-g576a041-dirty khadas#14 [ 2.012575@0] Call trace: [ 2.015201@0] [<ffffffc001088fe8>] dump_backtrace+0x0/0x140 [ 2.020830@0] [<ffffffc001089148>] show_stack+0x20/0x2c [ 2.026046@0] [<ffffffc001b17acc>] dump_stack+0x74/0xc0 [ 2.031302@0] [<ffffffc00109eaa0>] warn_slowpath_common+0x90/0xb8 [ 2.037438@0] [<ffffffc00109eb3c>] warn_slowpath_fmt+0x74/0x88 [ 2.043290@0] [<ffffffc00143b73c>] gpio_to_desc+0x54/0x60 [ 2.048706@0] [<ffffffc00143c430>] gpio_request+0x20/0x38 [ 2.054157@0] [<ffffffc0014a5130>] at24_wp_enable+0x30/0x78 [ 2.059731@0] [<ffffffc0014a558c>] at24_dt_parse+0x9c/0x110 [ 2.065338@0] [<ffffffc0014a5914>] at24_probe+0x314/0x584 [ 2.070782@0] [<ffffffc00159d560>] i2c_device_probe+0xa0/0xe4 [ 2.076533@0] [<ffffffc001485d08>] really_probe+0x74/0x240 [ 2.082051@0] [<ffffffc00148600c>] __driver_attach+0xb0/0xb8 [ 2.087749@0] [<ffffffc001483e54>] bus_for_each_dev+0x68/0xac [ 2.093513@0] [<ffffffc001485810>] driver_attach+0x2c/0x38 [ 2.099019@0] [<ffffffc001485414>] bus_add_driver+0x158/0x210 [ 2.104818@0] [<ffffffc0014867b0>] driver_register+0x6c/0x138 [ 2.110575@0] [<ffffffc00159d3dc>] i2c_register_driver+0x3c/0xc0 [ 2.116609@0] [<ffffffc001f66480>] at24_init+0x50/0x5c [ 2.121792@0] [<ffffffc0010816b8>] do_one_initcall+0xe0/0x12c [ 2.127546@0] [<ffffffc001f38924>] kernel_init_freeable+0x134/0x1d8 [ 2.133851@0] [<ffffffc001b0f390>] kernel_init+0x1c/0xdc [ 2.139213@0] ---[ end trace c84d7b19dc3d49e2 ]--- [ 2.144000@0] gpiod_request: invalid GPIO [ 2.148017@0] faild to alloc write protect (-1514520)! [ 2.153185@0] EEPROM_AT24c256 [ 2.156086@0] write protect port level is -1514520[ 2.160888@0] wp_port=-1514520 write_ops_interval=-64ms [ 2.166151@0] at24 2-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write Signed-off-by: Benoît Thébaudeau <[email protected]>

[ Upstream commit d754941 ] If, for any reason, userland shuts down iscsi transport interfaces before proper logouts - like when logging in to LUNs manually, without logging out on server shutdown, or when automated scripts can't umount/logout from logged LUNs - kernel will hang forever on its sd_sync_cache() logic, after issuing the SYNCHRONIZE_CACHE cmd to all still existent paths. PID: 1 TASK: ffff8801a69b8000 CPU: 1 COMMAND: "systemd-shutdow" #0 [ffff8801a69c3a30] __schedule at ffffffff8183e9ee #1 [ffff8801a69c3a80] schedule at ffffffff8183f0d5 #2 [ffff8801a69c3a98] schedule_timeout at ffffffff81842199 #3 [ffff8801a69c3b40] io_schedule_timeout at ffffffff8183e604 #4 [ffff8801a69c3b70] wait_for_completion_io_timeout at ffffffff8183fc6c khadas#5 [ffff8801a69c3bd0] blk_execute_rq at ffffffff813cfe10 khadas#6 [ffff8801a69c3c88] scsi_execute at ffffffff815c3fc7 khadas#7 [ffff8801a69c3cc8] scsi_execute_req_flags at ffffffff815c60fe khadas#8 [ffff8801a69c3d30] sd_sync_cache at ffffffff815d37d7 khadas#9 [ffff8801a69c3da8] sd_shutdown at ffffffff815d3c3c This happens because iscsi_eh_cmd_timed_out(), the transport layer timeout helper, would tell the queue timeout function (scsi_times_out) to reset the request timer over and over, until the session state is back to logged in state. Unfortunately, during server shutdown, this might never happen again. Other option would be "not to handle" the issue in the transport layer. That would trigger the error handler logic, which would also need the session state to be logged in again. Best option, for such case, is to tell upper layers that the command was handled during the transport layer error handler helper, marking it as DID_NO_CONNECT, which will allow completion and inform about the problem. After the session was marked as ISCSI_STATE_FAILED, due to the first timeout during the server shutdown phase, all subsequent cmds will fail to be queued, allowing upper logic to fail faster. Signed-off-by: Rafael David Tinoco <[email protected]> Reviewed-by: Lee Duncan <[email protected]> Signed-off-by: Martin K. Petersen <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 2c0aa08 ] Scenario: 1. Port down and do fail over 2. Ap do rds_bind syscall PID: 47039 TASK: ffff89887e2fe640 CPU: 47 COMMAND: "kworker/u:6" #0 [ffff898e35f159f0] machine_kexec at ffffffff8103abf9 #1 [ffff898e35f15a60] crash_kexec at ffffffff810b96e3 #2 [ffff898e35f15b30] oops_end at ffffffff8150f518 #3 [ffff898e35f15b60] no_context at ffffffff8104854c #4 [ffff898e35f15ba0] __bad_area_nosemaphore at ffffffff81048675 khadas#5 [ffff898e35f15bf0] bad_area_nosemaphore at ffffffff810487d3 khadas#6 [ffff898e35f15c00] do_page_fault at ffffffff815120b8 khadas#7 [ffff898e35f15d10] page_fault at ffffffff8150ea95 [exception RIP: unknown or invalid address] RIP: 0000000000000000 RSP: ffff898e35f15dc8 RFLAGS: 00010282 RAX: 00000000fffffffe RBX: ffff889b77f6fc00 RCX:ffffffff81c99d88 RDX: 0000000000000000 RSI: ffff896019ee08e8 RDI:ffff889b77f6fc00 RBP: ffff898e35f15df0 R8: ffff896019ee08c8 R9:0000000000000000 R10: 0000000000000400 R11: 0000000000000000 R12:ffff896019ee08c0 R13: ffff889b77f6fe68 R14: ffffffff81c99d80 R15: ffffffffa022a1e0 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 khadas#8 [ffff898e35f15dc8] cma_ndev_work_handler at ffffffffa022a228 [rdma_cm] khadas#9 [ffff898e35f15df8] process_one_work at ffffffff8108a7c6 khadas#10 [ffff898e35f15e58] worker_thread at ffffffff8108bda0 khadas#11 [ffff898e35f15ee8] kthread at ffffffff81090fe6 PID: 45659 TASK: ffff880d313d2500 CPU: 31 COMMAND: "oracle_45659_ap" #0 [ffff881024ccfc98] __schedule at ffffffff8150bac4 #1 [ffff881024ccfd40] schedule at ffffffff8150c2cf #2 [ffff881024ccfd50] __mutex_lock_slowpath at ffffffff8150cee7 #3 [ffff881024ccfdc0] mutex_lock at ffffffff8150cdeb #4 [ffff881024ccfde0] rdma_destroy_id at ffffffffa022a027 [rdma_cm] khadas#5 [ffff881024ccfe10] rds_ib_laddr_check at ffffffffa0357857 [rds_rdma] khadas#6 [ffff881024ccfe50] rds_trans_get_preferred at ffffffffa0324c2a [rds] khadas#7 [ffff881024ccfe80] rds_bind at ffffffffa031d690 [rds] khadas#8 [ffff881024ccfeb0] sys_bind at ffffffff8142a670 PID: 45659 PID: 47039 rds_ib_laddr_check /* create id_priv with a null event_handler */ rdma_create_id rdma_bind_addr cma_acquire_dev /* add id_priv to cma_dev->id_list */ cma_attach_to_dev cma_ndev_work_handler /* event_hanlder is null */ id_priv->id.event_handler Signed-off-by: Guanglei Li <[email protected]> Signed-off-by: Honglei Wang <[email protected]> Reviewed-by: Junxiao Bi <[email protected]> Reviewed-by: Yanjun Zhu <[email protected]> Reviewed-by: Leon Romanovsky <[email protected]> Acked-by: Santosh Shilimkar <[email protected]> Acked-by: Doug Ledford <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 2bbea6e ] when mounting an ISO filesystem sometimes (very rarely) the system hangs because of a race condition between two tasks. PID: 6766 TASK: ffff88007b2a6dd0 CPU: 0 COMMAND: "mount" #0 [ffff880078447ae0] __schedule at ffffffff8168d605 #1 [ffff880078447b48] schedule_preempt_disabled at ffffffff8168ed49 #2 [ffff880078447b58] __mutex_lock_slowpath at ffffffff8168c995 #3 [ffff880078447bb8] mutex_lock at ffffffff8168bdef #4 [ffff880078447bd0] sr_block_ioctl at ffffffffa00b6818 [sr_mod] khadas#5 [ffff880078447c10] blkdev_ioctl at ffffffff812fea50 khadas#6 [ffff880078447c70] ioctl_by_bdev at ffffffff8123a8b3 khadas#7 [ffff880078447c90] isofs_fill_super at ffffffffa04fb1e1 [isofs] khadas#8 [ffff880078447da8] mount_bdev at ffffffff81202570 khadas#9 [ffff880078447e18] isofs_mount at ffffffffa04f9828 [isofs] khadas#10 [ffff880078447e28] mount_fs at ffffffff81202d09 khadas#11 [ffff880078447e70] vfs_kern_mount at ffffffff8121ea8f khadas#12 [ffff880078447ea8] do_mount at ffffffff81220fee khadas#13 [ffff880078447f28] sys_mount at ffffffff812218d6 khadas#14 [ffff880078447f80] system_call_fastpath at ffffffff81698c49 RIP: 00007fd9ea914e9a RSP: 00007ffd5d9bf648 RFLAGS: 00010246 RAX: 00000000000000a5 RBX: ffffffff81698c49 RCX: 0000000000000010 RDX: 00007fd9ec2bc210 RSI: 00007fd9ec2bc290 RDI: 00007fd9ec2bcf30 RBP: 0000000000000000 R8: 0000000000000000 R9: 0000000000000010 R10: 00000000c0ed0001 R11: 0000000000000206 R12: 00007fd9ec2bc040 R13: 00007fd9eb6b2380 R14: 00007fd9ec2bc210 R15: 00007fd9ec2bcf30 ORIG_RAX: 00000000000000a5 CS: 0033 SS: 002b This task was trying to mount the cdrom. It allocated and configured a super_block struct and owned the write-lock for the super_block->s_umount rwsem. While exclusively owning the s_umount lock, it called sr_block_ioctl and waited to acquire the global sr_mutex lock. PID: 6785 TASK: ffff880078720fb0 CPU: 0 COMMAND: "systemd-udevd" #0 [ffff880078417898] __schedule at ffffffff8168d605 #1 [ffff880078417900] schedule at ffffffff8168dc59 #2 [ffff880078417910] rwsem_down_read_failed at ffffffff8168f605 #3 [ffff880078417980] call_rwsem_down_read_failed at ffffffff81328838 #4 [ffff8800784179d0] down_read at ffffffff8168cde0 khadas#5 [ffff8800784179e8] get_super at ffffffff81201cc7 khadas#6 [ffff880078417a10] __invalidate_device at ffffffff8123a8de khadas#7 [ffff880078417a40] flush_disk at ffffffff8123a94b khadas#8 [ffff880078417a88] check_disk_change at ffffffff8123ab50 khadas#9 [ffff880078417ab0] cdrom_open at ffffffffa00a29e1 [cdrom] khadas#10 [ffff880078417b68] sr_block_open at ffffffffa00b6f9b [sr_mod] khadas#11 [ffff880078417b98] __blkdev_get at ffffffff8123ba86 khadas#12 [ffff880078417bf0] blkdev_get at ffffffff8123bd65 khadas#13 [ffff880078417c78] blkdev_open at ffffffff8123bf9b khadas#14 [ffff880078417c90] do_dentry_open at ffffffff811fc7f7 khadas#15 [ffff880078417cd8] vfs_open at ffffffff811fc9cf khadas#16 [ffff880078417d00] do_last at ffffffff8120d53d khadas#17 [ffff880078417db0] path_openat at ffffffff8120e6b2 khadas#18 [ffff880078417e48] do_filp_open at ffffffff8121082b khadas#19 [ffff880078417f18] do_sys_open at ffffffff811fdd33 khadas#20 [ffff880078417f70] sys_open at ffffffff811fde4e khadas#21 [ffff880078417f80] system_call_fastpath at ffffffff81698c49 RIP: 00007f29438b0c20 RSP: 00007ffc76624b78 RFLAGS: 00010246 RAX: 0000000000000002 RBX: ffffffff81698c49 RCX: 0000000000000000 RDX: 00007f2944a5fa70 RSI: 00000000000a0800 RDI: 00007f2944a5fa70 RBP: 00007f2944a5f540 R8: 0000000000000000 R9: 0000000000000020 R10: 00007f2943614c40 R11: 0000000000000246 R12: ffffffff811fde4e R13: ffff880078417f78 R14: 000000000000000c R15: 00007f2944a4b010 ORIG_RAX: 0000000000000002 CS: 0033 SS: 002b This task tried to open the cdrom device, the sr_block_open function acquired the global sr_mutex lock. The call to check_disk_change() then saw an event flag indicating a possible media change and tried to flush any cached data for the device. As part of the flush, it tried to acquire the super_block->s_umount lock associated with the cdrom device. This was the same super_block as created and locked by the previous task. The first task acquires the s_umount lock and then the sr_mutex_lock; the second task acquires the sr_mutex_lock and then the s_umount lock. This patch fixes the issue by moving check_disk_change() out of cdrom_open() and let the caller take care of it. Signed-off-by: Maurizio Lombardi <[email protected]> Signed-off-by: Jens Axboe <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 2c0aa08 ] Scenario: 1. Port down and do fail over 2. Ap do rds_bind syscall PID: 47039 TASK: ffff89887e2fe640 CPU: 47 COMMAND: "kworker/u:6" #0 [ffff898e35f159f0] machine_kexec at ffffffff8103abf9 #1 [ffff898e35f15a60] crash_kexec at ffffffff810b96e3 #2 [ffff898e35f15b30] oops_end at ffffffff8150f518 #3 [ffff898e35f15b60] no_context at ffffffff8104854c #4 [ffff898e35f15ba0] __bad_area_nosemaphore at ffffffff81048675 #5 [ffff898e35f15bf0] bad_area_nosemaphore at ffffffff810487d3 #6 [ffff898e35f15c00] do_page_fault at ffffffff815120b8 #7 [ffff898e35f15d10] page_fault at ffffffff8150ea95 [exception RIP: unknown or invalid address] RIP: 0000000000000000 RSP: ffff898e35f15dc8 RFLAGS: 00010282 RAX: 00000000fffffffe RBX: ffff889b77f6fc00 RCX:ffffffff81c99d88 RDX: 0000000000000000 RSI: ffff896019ee08e8 RDI:ffff889b77f6fc00 RBP: ffff898e35f15df0 R8: ffff896019ee08c8 R9:0000000000000000 R10: 0000000000000400 R11: 0000000000000000 R12:ffff896019ee08c0 R13: ffff889b77f6fe68 R14: ffffffff81c99d80 R15: ffffffffa022a1e0 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 #8 [ffff898e35f15dc8] cma_ndev_work_handler at ffffffffa022a228 [rdma_cm] #9 [ffff898e35f15df8] process_one_work at ffffffff8108a7c6 #10 [ffff898e35f15e58] worker_thread at ffffffff8108bda0 #11 [ffff898e35f15ee8] kthread at ffffffff81090fe6 PID: 45659 TASK: ffff880d313d2500 CPU: 31 COMMAND: "oracle_45659_ap" #0 [ffff881024ccfc98] __schedule at ffffffff8150bac4 #1 [ffff881024ccfd40] schedule at ffffffff8150c2cf #2 [ffff881024ccfd50] __mutex_lock_slowpath at ffffffff8150cee7 #3 [ffff881024ccfdc0] mutex_lock at ffffffff8150cdeb #4 [ffff881024ccfde0] rdma_destroy_id at ffffffffa022a027 [rdma_cm] #5 [ffff881024ccfe10] rds_ib_laddr_check at ffffffffa0357857 [rds_rdma] #6 [ffff881024ccfe50] rds_trans_get_preferred at ffffffffa0324c2a [rds] #7 [ffff881024ccfe80] rds_bind at ffffffffa031d690 [rds] #8 [ffff881024ccfeb0] sys_bind at ffffffff8142a670 PID: 45659 PID: 47039 rds_ib_laddr_check /* create id_priv with a null event_handler */ rdma_create_id rdma_bind_addr cma_acquire_dev /* add id_priv to cma_dev->id_list */ cma_attach_to_dev cma_ndev_work_handler /* event_hanlder is null */ id_priv->id.event_handler Signed-off-by: Guanglei Li <[email protected]> Signed-off-by: Honglei Wang <[email protected]> Reviewed-by: Junxiao Bi <[email protected]> Reviewed-by: Yanjun Zhu <[email protected]> Reviewed-by: Leon Romanovsky <[email protected]> Acked-by: Santosh Shilimkar <[email protected]> Acked-by: Doug Ledford <[email protected]> Signed-off-by: David S. Miller <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 2bbea6e ] when mounting an ISO filesystem sometimes (very rarely) the system hangs because of a race condition between two tasks. PID: 6766 TASK: ffff88007b2a6dd0 CPU: 0 COMMAND: "mount" #0 [ffff880078447ae0] __schedule at ffffffff8168d605 #1 [ffff880078447b48] schedule_preempt_disabled at ffffffff8168ed49 #2 [ffff880078447b58] __mutex_lock_slowpath at ffffffff8168c995 #3 [ffff880078447bb8] mutex_lock at ffffffff8168bdef #4 [ffff880078447bd0] sr_block_ioctl at ffffffffa00b6818 [sr_mod] #5 [ffff880078447c10] blkdev_ioctl at ffffffff812fea50 #6 [ffff880078447c70] ioctl_by_bdev at ffffffff8123a8b3 #7 [ffff880078447c90] isofs_fill_super at ffffffffa04fb1e1 [isofs] #8 [ffff880078447da8] mount_bdev at ffffffff81202570 #9 [ffff880078447e18] isofs_mount at ffffffffa04f9828 [isofs] #10 [ffff880078447e28] mount_fs at ffffffff81202d09 #11 [ffff880078447e70] vfs_kern_mount at ffffffff8121ea8f #12 [ffff880078447ea8] do_mount at ffffffff81220fee #13 [ffff880078447f28] sys_mount at ffffffff812218d6 #14 [ffff880078447f80] system_call_fastpath at ffffffff81698c49 RIP: 00007fd9ea914e9a RSP: 00007ffd5d9bf648 RFLAGS: 00010246 RAX: 00000000000000a5 RBX: ffffffff81698c49 RCX: 0000000000000010 RDX: 00007fd9ec2bc210 RSI: 00007fd9ec2bc290 RDI: 00007fd9ec2bcf30 RBP: 0000000000000000 R8: 0000000000000000 R9: 0000000000000010 R10: 00000000c0ed0001 R11: 0000000000000206 R12: 00007fd9ec2bc040 R13: 00007fd9eb6b2380 R14: 00007fd9ec2bc210 R15: 00007fd9ec2bcf30 ORIG_RAX: 00000000000000a5 CS: 0033 SS: 002b This task was trying to mount the cdrom. It allocated and configured a super_block struct and owned the write-lock for the super_block->s_umount rwsem. While exclusively owning the s_umount lock, it called sr_block_ioctl and waited to acquire the global sr_mutex lock. PID: 6785 TASK: ffff880078720fb0 CPU: 0 COMMAND: "systemd-udevd" #0 [ffff880078417898] __schedule at ffffffff8168d605 #1 [ffff880078417900] schedule at ffffffff8168dc59 #2 [ffff880078417910] rwsem_down_read_failed at ffffffff8168f605 #3 [ffff880078417980] call_rwsem_down_read_failed at ffffffff81328838 #4 [ffff8800784179d0] down_read at ffffffff8168cde0 #5 [ffff8800784179e8] get_super at ffffffff81201cc7 #6 [ffff880078417a10] __invalidate_device at ffffffff8123a8de #7 [ffff880078417a40] flush_disk at ffffffff8123a94b #8 [ffff880078417a88] check_disk_change at ffffffff8123ab50 #9 [ffff880078417ab0] cdrom_open at ffffffffa00a29e1 [cdrom] #10 [ffff880078417b68] sr_block_open at ffffffffa00b6f9b [sr_mod] #11 [ffff880078417b98] __blkdev_get at ffffffff8123ba86 #12 [ffff880078417bf0] blkdev_get at ffffffff8123bd65 #13 [ffff880078417c78] blkdev_open at ffffffff8123bf9b #14 [ffff880078417c90] do_dentry_open at ffffffff811fc7f7 #15 [ffff880078417cd8] vfs_open at ffffffff811fc9cf #16 [ffff880078417d00] do_last at ffffffff8120d53d #17 [ffff880078417db0] path_openat at ffffffff8120e6b2 #18 [ffff880078417e48] do_filp_open at ffffffff8121082b #19 [ffff880078417f18] do_sys_open at ffffffff811fdd33 #20 [ffff880078417f70] sys_open at ffffffff811fde4e #21 [ffff880078417f80] system_call_fastpath at ffffffff81698c49 RIP: 00007f29438b0c20 RSP: 00007ffc76624b78 RFLAGS: 00010246 RAX: 0000000000000002 RBX: ffffffff81698c49 RCX: 0000000000000000 RDX: 00007f2944a5fa70 RSI: 00000000000a0800 RDI: 00007f2944a5fa70 RBP: 00007f2944a5f540 R8: 0000000000000000 R9: 0000000000000020 R10: 00007f2943614c40 R11: 0000000000000246 R12: ffffffff811fde4e R13: ffff880078417f78 R14: 000000000000000c R15: 00007f2944a4b010 ORIG_RAX: 0000000000000002 CS: 0033 SS: 002b This task tried to open the cdrom device, the sr_block_open function acquired the global sr_mutex lock. The call to check_disk_change() then saw an event flag indicating a possible media change and tried to flush any cached data for the device. As part of the flush, it tried to acquire the super_block->s_umount lock associated with the cdrom device. This was the same super_block as created and locked by the previous task. The first task acquires the s_umount lock and then the sr_mutex_lock; the second task acquires the sr_mutex_lock and then the s_umount lock. This patch fixes the issue by moving check_disk_change() out of cdrom_open() and let the caller take care of it. Signed-off-by: Maurizio Lombardi <[email protected]> Signed-off-by: Jens Axboe <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 89da619 upstream. Kernel panic when with high memory pressure, calltrace looks like, PID: 21439 TASK: ffff881be3afedd0 CPU: 16 COMMAND: "java" #0 [ffff881ec7ed7630] machine_kexec at ffffffff81059beb #1 [ffff881ec7ed7690] __crash_kexec at ffffffff81105942 #2 [ffff881ec7ed7760] crash_kexec at ffffffff81105a30 #3 [ffff881ec7ed7778] oops_end at ffffffff816902c8 #4 [ffff881ec7ed77a0] no_context at ffffffff8167ff46 #5 [ffff881ec7ed77f0] __bad_area_nosemaphore at ffffffff8167ffdc #6 [ffff881ec7ed7838] __node_set at ffffffff81680300 #7 [ffff881ec7ed7860] __do_page_fault at ffffffff8169320f #8 [ffff881ec7ed78c0] do_page_fault at ffffffff816932b5 #9 [ffff881ec7ed78f0] page_fault at ffffffff8168f4c8 [exception RIP: _raw_spin_lock_irqsave+47] RIP: ffffffff8168edef RSP: ffff881ec7ed79a8 RFLAGS: 00010046 RAX: 0000000000000246 RBX: ffffea0019740d00 RCX: ffff881ec7ed7fd8 RDX: 0000000000020000 RSI: 0000000000000016 RDI: 0000000000000008 RBP: ffff881ec7ed79a8 R8: 0000000000000246 R9: 000000000001a098 R10: ffff88107ffda000 R11: 0000000000000000 R12: 0000000000000000 R13: 0000000000000008 R14: ffff881ec7ed7a80 R15: ffff881be3afedd0 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 It happens in the pagefault and results in double pagefault during compacting pages when memory allocation fails. Analysed the vmcore, the page leads to second pagefault is corrupted with _mapcount=-256, but private=0. It's caused by the race between migration and ballooning, and lock missing in virtballoon_migratepage() of virtio_balloon driver. This patch fix the bug. Fixes: e225042 ("virtio_balloon: introduce migration primitives to balloon pages") Cc: [email protected] Signed-off-by: Jiang Biao <[email protected]> Signed-off-by: Huang Chong <[email protected]> Signed-off-by: Michael S. Tsirkin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit f5e2848 ] When enumerating page size definitions to check hardware support, we construct a constant which is (1U << (def->shift - 10)). However, the array of page size definitions is only initalised for various MMU_PAGE_* constants, so it contains a number of 0-initialised elements with def->shift == 0. This means we end up shifting by a very large number, which gives the following UBSan splat: ================================================================================ UBSAN: Undefined behaviour in /home/dja/dev/linux/linux/arch/powerpc/mm/tlb_nohash.c:506:21 shift exponent 4294967286 is too large for 32-bit type 'unsigned int' CPU: 0 PID: 0 Comm: swapper Not tainted 4.19.0-rc3-00045-ga604f927b012-dirty khadas#6 Call Trace: [c00000000101bc20] [c000000000a13d54] .dump_stack+0xa8/0xec (unreliable) [c00000000101bcb0] [c0000000004f20a8] .ubsan_epilogue+0x18/0x64 [c00000000101bd30] [c0000000004f2b10] .__ubsan_handle_shift_out_of_bounds+0x110/0x1a4 [c00000000101be20] [c000000000d21760] .early_init_mmu+0x1b4/0x5a0 [c00000000101bf10] [c000000000d1ba28] .early_setup+0x100/0x130 [c00000000101bf90] [c000000000000528] start_here_multiplatform+0x68/0x80 ================================================================================ Fix this by first checking if the element exists (shift != 0) before constructing the constant. Signed-off-by: Daniel Axtens <[email protected]> Signed-off-by: Michael Ellerman <[email protected]> Signed-off-by: Sasha Levin <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 7298e3b upstream. Currently the calcuation of end_pfn can round up the pfn number to more than the actual maximum number of pfns, causing an Oops. Fix this by ensuring end_pfn is never more than max_pfn. This can be easily triggered when on systems where the end_pfn gets rounded up to more than max_pfn using the idle-page stress-ng stress test: sudo stress-ng --idle-page 0 BUG: unable to handle kernel paging request at 00000000000020d8 #PF error: [normal kernel read fault] PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 1 PID: 11039 Comm: stress-ng-idle- Not tainted 5.0.0-5-generic khadas#6-Ubuntu Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 RIP: 0010:page_idle_get_page+0xc8/0x1a0 Code: 0f b1 0a 75 7d 48 8b 03 48 89 c2 48 c1 e8 33 83 e0 07 48 c1 ea 36 48 8d 0c 40 4c 8d 24 88 49 c1 e4 07 4c 03 24 d5 00 89 c3 be <49> 8b 44 24 58 48 8d b8 80 a1 02 00 e8 07 d5 77 00 48 8b 53 08 48 RSP: 0018:ffffafd7c672fde8 EFLAGS: 00010202 RAX: 0000000000000005 RBX: ffffe36341fff700 RCX: 000000000000000f RDX: 0000000000000284 RSI: 0000000000000275 RDI: 0000000001fff700 RBP: ffffafd7c672fe00 R08: ffffa0bc34056410 R09: 0000000000000276 R10: ffffa0bc754e9b40 R11: ffffa0bc330f6400 R12: 0000000000002080 R13: ffffe36341fff700 R14: 0000000000080000 R15: ffffa0bc330f6400 FS: 00007f0ec1ea5740(0000) GS:ffffa0bc7db00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000000020d8 CR3: 0000000077d68000 CR4: 00000000000006e0 Call Trace: page_idle_bitmap_write+0x8c/0x140 sysfs_kf_bin_write+0x5c/0x70 kernfs_fop_write+0x12e/0x1b0 __vfs_write+0x1b/0x40 vfs_write+0xab/0x1b0 ksys_write+0x55/0xc0 __x64_sys_write+0x1a/0x20 do_syscall_64+0x5a/0x110 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Link: http://lkml.kernel.org/r/[email protected] Fixes: 33c3fc7 ("mm: introduce idle page tracking") Signed-off-by: Colin Ian King <[email protected]> Reviewed-by: Andrew Morton <[email protected]> Acked-by: Vladimir Davydov <[email protected]> Cc: Michal Hocko <[email protected]> Cc: Mike Rapoport <[email protected]> Cc: Mel Gorman <[email protected]> Cc: Stephen Rothwell <[email protected]> Cc: Andrey Ryabinin <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]> Signed-off-by: Linus Torvalds <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 42dfa45 ] Using gcc's ASan, Changbin reports: ================================================================= ==7494==ERROR: LeakSanitizer: detected memory leaks Direct leak of 48 byte(s) in 1 object(s) allocated from: #0 0x7f0333a89138 in calloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee138) #1 0x5625e5330a5e in zalloc util/util.h:23 #2 0x5625e5330a9b in perf_counts__new util/counts.c:10 #3 0x5625e5330ca0 in perf_evsel__alloc_counts util/counts.c:47 #4 0x5625e520d8e5 in __perf_evsel__read_on_cpu util/evsel.c:1505 khadas#5 0x5625e517a985 in perf_evsel__read_on_cpu /home/work/linux/tools/perf/util/evsel.h:347 khadas#6 0x5625e517ad1a in test__openat_syscall_event tests/openat-syscall.c:47 khadas#7 0x5625e51528e6 in run_test tests/builtin-test.c:358 khadas#8 0x5625e5152baf in test_and_print tests/builtin-test.c:388 khadas#9 0x5625e51543fe in __cmd_test tests/builtin-test.c:583 khadas#10 0x5625e515572f in cmd_test tests/builtin-test.c:722 khadas#11 0x5625e51c3fb8 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302 khadas#12 0x5625e51c44f7 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354 khadas#13 0x5625e51c48fb in run_argv /home/changbin/work/linux/tools/perf/perf.c:398 khadas#14 0x5625e51c5069 in main /home/changbin/work/linux/tools/perf/perf.c:520 khadas#15 0x7f033214d09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a) Indirect leak of 72 byte(s) in 1 object(s) allocated from: #0 0x7f0333a89138 in calloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee138) #1 0x5625e532560d in zalloc util/util.h:23 #2 0x5625e532566b in xyarray__new util/xyarray.c:10 #3 0x5625e5330aba in perf_counts__new util/counts.c:15 #4 0x5625e5330ca0 in perf_evsel__alloc_counts util/counts.c:47 khadas#5 0x5625e520d8e5 in __perf_evsel__read_on_cpu util/evsel.c:1505 khadas#6 0x5625e517a985 in perf_evsel__read_on_cpu /home/work/linux/tools/perf/util/evsel.h:347 khadas#7 0x5625e517ad1a in test__openat_syscall_event tests/openat-syscall.c:47 khadas#8 0x5625e51528e6 in run_test tests/builtin-test.c:358 khadas#9 0x5625e5152baf in test_and_print tests/builtin-test.c:388 khadas#10 0x5625e51543fe in __cmd_test tests/builtin-test.c:583 khadas#11 0x5625e515572f in cmd_test tests/builtin-test.c:722 khadas#12 0x5625e51c3fb8 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302 khadas#13 0x5625e51c44f7 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354 khadas#14 0x5625e51c48fb in run_argv /home/changbin/work/linux/tools/perf/perf.c:398 khadas#15 0x5625e51c5069 in main /home/changbin/work/linux/tools/perf/perf.c:520 khadas#16 0x7f033214d09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a) His patch took care of evsel->prev_raw_counts, but the above backtraces are about evsel->counts, so fix that instead. Reported-by: Changbin Du <[email protected]> Cc: Alexei Starovoitov <[email protected]> Cc: Daniel Borkmann <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Steven Rostedt (VMware) <[email protected]> Link: https://lkml.kernel.org/n/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

…_event_on_all_cpus test [ Upstream commit 93faa52 ] ================================================================= ==7497==ERROR: LeakSanitizer: detected memory leaks Direct leak of 40 byte(s) in 1 object(s) allocated from: #0 0x7f0333a88f30 in __interceptor_malloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xedf30) #1 0x5625e5326213 in cpu_map__trim_new util/cpumap.c:45 #2 0x5625e5326703 in cpu_map__read util/cpumap.c:103 #3 0x5625e53267ef in cpu_map__read_all_cpu_map util/cpumap.c:120 #4 0x5625e5326915 in cpu_map__new util/cpumap.c:135 khadas#5 0x5625e517b355 in test__openat_syscall_event_on_all_cpus tests/openat-syscall-all-cpus.c:36 khadas#6 0x5625e51528e6 in run_test tests/builtin-test.c:358 khadas#7 0x5625e5152baf in test_and_print tests/builtin-test.c:388 khadas#8 0x5625e51543fe in __cmd_test tests/builtin-test.c:583 khadas#9 0x5625e515572f in cmd_test tests/builtin-test.c:722 khadas#10 0x5625e51c3fb8 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302 khadas#11 0x5625e51c44f7 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354 khadas#12 0x5625e51c48fb in run_argv /home/changbin/work/linux/tools/perf/perf.c:398 khadas#13 0x5625e51c5069 in main /home/changbin/work/linux/tools/perf/perf.c:520 khadas#14 0x7f033214d09a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a) Signed-off-by: Changbin Du <[email protected]> Reviewed-by: Jiri Olsa <[email protected]> Cc: Alexei Starovoitov <[email protected]> Cc: Daniel Borkmann <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Steven Rostedt (VMware) <[email protected]> Fixes: f30a79b ("perf tools: Add reference counting for cpu_map object") Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit d982b33 ] ================================================================= ==20875==ERROR: LeakSanitizer: detected memory leaks Direct leak of 1160 byte(s) in 1 object(s) allocated from: #0 0x7f1b6fc84138 in calloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xee138) #1 0x55bd50005599 in zalloc util/util.h:23 #2 0x55bd500068f5 in perf_evsel__newtp_idx util/evsel.c:327 #3 0x55bd4ff810fc in perf_evsel__newtp /home/work/linux/tools/perf/util/evsel.h:216 #4 0x55bd4ff81608 in test__perf_evsel__tp_sched_test tests/evsel-tp-sched.c:69 khadas#5 0x55bd4ff528e6 in run_test tests/builtin-test.c:358 khadas#6 0x55bd4ff52baf in test_and_print tests/builtin-test.c:388 khadas#7 0x55bd4ff543fe in __cmd_test tests/builtin-test.c:583 khadas#8 0x55bd4ff5572f in cmd_test tests/builtin-test.c:722 khadas#9 0x55bd4ffc4087 in run_builtin /home/changbin/work/linux/tools/perf/perf.c:302 khadas#10 0x55bd4ffc45c6 in handle_internal_command /home/changbin/work/linux/tools/perf/perf.c:354 khadas#11 0x55bd4ffc49ca in run_argv /home/changbin/work/linux/tools/perf/perf.c:398 khadas#12 0x55bd4ffc5138 in main /home/changbin/work/linux/tools/perf/perf.c:520 khadas#13 0x7f1b6e34809a in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2409a) Indirect leak of 19 byte(s) in 1 object(s) allocated from: #0 0x7f1b6fc83f30 in __interceptor_malloc (/usr/lib/x86_64-linux-gnu/libasan.so.5+0xedf30) #1 0x7f1b6e3ac30f in vasprintf (/lib/x86_64-linux-gnu/libc.so.6+0x8830f) Signed-off-by: Changbin Du <[email protected]> Reviewed-by: Jiri Olsa <[email protected]> Cc: Alexei Starovoitov <[email protected]> Cc: Daniel Borkmann <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Steven Rostedt (VMware) <[email protected]> Fixes: 6a6cd11 ("perf test: Add test for the sched tracepoint format fields") Link: http://lkml.kernel.org/r/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit cf3591e upstream. Revert the commit bd293d0. The proper fix has been made available with commit d0a255e ("loop: set PF_MEMALLOC_NOIO for the worker thread"). Note that the fix offered by commit bd293d0 doesn't really prevent the deadlock from occuring - if we look at the stacktrace reported by Junxiao Bi, we see that it hangs in bit_wait_io and not on the mutex - i.e. it has already successfully taken the mutex. Changing the mutex from mutex_lock to mutex_trylock won't help with deadlocks that happen afterwards. PID: 474 TASK: ffff8813e11f4600 CPU: 10 COMMAND: "kswapd0" #0 [ffff8813dedfb938] __schedule at ffffffff8173f405 #1 [ffff8813dedfb990] schedule at ffffffff8173fa27 #2 [ffff8813dedfb9b0] schedule_timeout at ffffffff81742fec #3 [ffff8813dedfba60] io_schedule_timeout at ffffffff8173f186 #4 [ffff8813dedfbaa0] bit_wait_io at ffffffff8174034f khadas#5 [ffff8813dedfbac0] __wait_on_bit at ffffffff8173fec8 khadas#6 [ffff8813dedfbb10] out_of_line_wait_on_bit at ffffffff8173ff81 khadas#7 [ffff8813dedfbb90] __make_buffer_clean at ffffffffa038736f [dm_bufio] khadas#8 [ffff8813dedfbbb0] __try_evict_buffer at ffffffffa0387bb8 [dm_bufio] khadas#9 [ffff8813dedfbbd0] dm_bufio_shrink_scan at ffffffffa0387cc3 [dm_bufio] khadas#10 [ffff8813dedfbc40] shrink_slab at ffffffff811a87ce khadas#11 [ffff8813dedfbd30] shrink_zone at ffffffff811ad778 khadas#12 [ffff8813dedfbdc0] kswapd at ffffffff811ae92f khadas#13 [ffff8813dedfbec0] kthread at ffffffff810a8428 khadas#14 [ffff8813dedfbf50] ret_from_fork at ffffffff81745242 Signed-off-by: Mikulas Patocka <[email protected]> Cc: [email protected] Fixes: bd293d0 ("dm bufio: fix deadlock with loop device") Depends-on: d0a255e ("loop: set PF_MEMALLOC_NOIO for the worker thread") Signed-off-by: Mike Snitzer <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit 314eed3 upstream. When running on a system with >512MB RAM with a 32-bit kernel built with: CONFIG_DEBUG_VIRTUAL=y CONFIG_HIGHMEM=y CONFIG_HARDENED_USERCOPY=y all execve()s will fail due to argv copying into kmap()ed pages, and on usercopy checking the calls ultimately of virt_to_page() will be looking for "bad" kmap (highmem) pointers due to CONFIG_DEBUG_VIRTUAL=y: ------------[ cut here ]------------ kernel BUG at ../arch/x86/mm/physaddr.c:83! invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.3.0-rc8 khadas#6 Hardware name: Dell Inc. Inspiron 1318/0C236D, BIOS A04 01/15/2009 EIP: __phys_addr+0xaf/0x100 ... Call Trace: __check_object_size+0xaf/0x3c0 ? __might_sleep+0x80/0xa0 copy_strings+0x1c2/0x370 copy_strings_kernel+0x2b/0x40 __do_execve_file+0x4ca/0x810 ? kmem_cache_alloc+0x1c7/0x370 do_execve+0x1b/0x20 ... The check is from arch/x86/mm/physaddr.c: VIRTUAL_BUG_ON((phys_addr >> PAGE_SHIFT) > max_low_pfn); Due to the kmap() in fs/exec.c: kaddr = kmap(kmapped_page); ... if (copy_from_user(kaddr+offset, str, bytes_to_copy)) ... Now we can fetch the correct page to avoid the pfn check. In both cases, hardened usercopy will need to walk the page-span checker (if enabled) to do sanity checking. Reported-by: Randy Dunlap <[email protected]> Tested-by: Randy Dunlap <[email protected]> Fixes: f5509cc ("mm: Hardened usercopy") Cc: Matthew Wilcox <[email protected]> Cc: [email protected] Signed-off-by: Kees Cook <[email protected]> Reviewed-by: Matthew Wilcox (Oracle) <[email protected]> Link: https://lore.kernel.org/r/201909171056.7F2FFD17@keescook Signed-off-by: Greg Kroah-Hartman <[email protected]>

[ Upstream commit 0216234 ] We release wrong pointer on error path in cpu_cache_level__read function, leading to segfault: (gdb) r record ls Starting program: /root/perf/tools/perf/perf record ls ... [ perf record: Woken up 1 times to write data ] double free or corruption (out) Thread 1 "perf" received signal SIGABRT, Aborted. 0x00007ffff7463798 in raise () from /lib64/power9/libc.so.6 (gdb) bt #0 0x00007ffff7463798 in raise () from /lib64/power9/libc.so.6 #1 0x00007ffff7443bac in abort () from /lib64/power9/libc.so.6 #2 0x00007ffff74af8bc in __libc_message () from /lib64/power9/libc.so.6 #3 0x00007ffff74b92b8 in malloc_printerr () from /lib64/power9/libc.so.6 #4 0x00007ffff74bb874 in _int_free () from /lib64/power9/libc.so.6 khadas#5 0x0000000010271260 in __zfree (ptr=0x7fffffffa0b0) at ../../lib/zalloc.. khadas#6 0x0000000010139340 in cpu_cache_level__read (cache=0x7fffffffa090, cac.. khadas#7 0x0000000010143c90 in build_caches (cntp=0x7fffffffa118, size=<optimiz.. ... Releasing the proper pointer. Fixes: 720e98b ("perf tools: Add perf data cache feature") Signed-off-by: Jiri Olsa <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Michael Petlan <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: [email protected]: # v4.6+ Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 443f2d5 ] Observe a segmentation fault when 'perf stat' is asked to repeat forever with the interval option. Without fix: # perf stat -r 0 -I 5000 -e cycles -a sleep 10 # time counts unit events 5.000211692 3,13,89,82,34,157 cycles 10.000380119 1,53,98,52,22,294 cycles 10.040467280 17,16,79,265 cycles Segmentation fault This problem was only observed when we use forever option aka -r 0 and works with limited repeats. Calling print_counter with ts being set to NULL, is not a correct option when interval is set. Hence avoid print_counter(NULL,..) if interval is set. With fix: # perf stat -r 0 -I 5000 -e cycles -a sleep 10 # time counts unit events 5.019866622 3,15,14,43,08,697 cycles 10.039865756 3,15,16,31,95,261 cycles 10.059950628 1,26,05,47,158 cycles 5.009902655 3,14,52,62,33,932 cycles 10.019880228 3,14,52,22,89,154 cycles 10.030543876 66,90,18,333 cycles 5.009848281 3,14,51,98,25,437 cycles 10.029854402 3,15,14,93,04,918 cycles 5.009834177 3,14,51,95,92,316 cycles Committer notes: Did the 'git bisect' to find the cset introducing the problem to add the Fixes tag below, and at that time the problem reproduced as: (gdb) run stat -r0 -I500 sleep 1 <SNIP> Program received signal SIGSEGV, Segmentation fault. print_interval (prefix=prefix@entry=0x7fffffffc8d0 "", ts=ts@entry=0x0) at builtin-stat.c:866 866 sprintf(prefix, "%6lu.%09lu%s", ts->tv_sec, ts->tv_nsec, csv_sep); (gdb) bt #0 print_interval (prefix=prefix@entry=0x7fffffffc8d0 "", ts=ts@entry=0x0) at builtin-stat.c:866 #1 0x000000000041860a in print_counters (ts=ts@entry=0x0, argc=argc@entry=2, argv=argv@entry=0x7fffffffd640) at builtin-stat.c:938 #2 0x0000000000419a7f in cmd_stat (argc=2, argv=0x7fffffffd640, prefix=<optimized out>) at builtin-stat.c:1411 #3 0x000000000045c65a in run_builtin (p=p@entry=0x6291b8 <commands+216>, argc=argc@entry=5, argv=argv@entry=0x7fffffffd640) at perf.c:370 #4 0x000000000045c893 in handle_internal_command (argc=5, argv=0x7fffffffd640) at perf.c:429 khadas#5 0x000000000045c8f1 in run_argv (argcp=argcp@entry=0x7fffffffd4ac, argv=argv@entry=0x7fffffffd4a0) at perf.c:473 khadas#6 0x000000000045cac9 in main (argc=<optimized out>, argv=<optimized out>) at perf.c:588 (gdb) Mostly the same as just before this patch: Program received signal SIGSEGV, Segmentation fault. 0x00000000005874a7 in print_interval (config=0xa1f2a0 <stat_config>, evlist=0xbc9b90, prefix=0x7fffffffd1c0 "`", ts=0x0) at util/stat-display.c:964 964 sprintf(prefix, "%6lu.%09lu%s", ts->tv_sec, ts->tv_nsec, config->csv_sep); (gdb) bt #0 0x00000000005874a7 in print_interval (config=0xa1f2a0 <stat_config>, evlist=0xbc9b90, prefix=0x7fffffffd1c0 "`", ts=0x0) at util/stat-display.c:964 #1 0x0000000000588047 in perf_evlist__print_counters (evlist=0xbc9b90, config=0xa1f2a0 <stat_config>, _target=0xa1f0c0 <target>, ts=0x0, argc=2, argv=0x7fffffffd670) at util/stat-display.c:1172 #2 0x000000000045390f in print_counters (ts=0x0, argc=2, argv=0x7fffffffd670) at builtin-stat.c:656 #3 0x0000000000456bb5 in cmd_stat (argc=2, argv=0x7fffffffd670) at builtin-stat.c:1960 #4 0x00000000004dd2e0 in run_builtin (p=0xa30e00 <commands+288>, argc=5, argv=0x7fffffffd670) at perf.c:310 khadas#5 0x00000000004dd54d in handle_internal_command (argc=5, argv=0x7fffffffd670) at perf.c:362 khadas#6 0x00000000004dd694 in run_argv (argcp=0x7fffffffd4cc, argv=0x7fffffffd4c0) at perf.c:406 khadas#7 0x00000000004dda11 in main (argc=5, argv=0x7fffffffd670) at perf.c:531 (gdb) Fixes: d4f63a4 ("perf stat: Introduce print_counters function") Signed-off-by: Srikar Dronamraju <[email protected]> Acked-by: Jiri Olsa <[email protected]> Tested-by: Arnaldo Carvalho de Melo <[email protected]> Tested-by: Ravi Bangoria <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: Naveen N. Rao <[email protected]> Cc: [email protected] # v4.2+ Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

commit cdea465 upstream. A vendor with a system having more than 128 CPUs occasionally encounters the following crash during shutdown. This is not an easily reproduceable event, but the vendor was able to provide the following analysis of the crash, which exhibits the same footprint each time. crash> bt PID: 0 TASK: ffff88017c70ce70 CPU: 5 COMMAND: "swapper/5" #0 [ffff88085c143ac8] machine_kexec at ffffffff81059c8b #1 [ffff88085c143b28] __crash_kexec at ffffffff811052e2 #2 [ffff88085c143bf8] crash_kexec at ffffffff811053d0 #3 [ffff88085c143c10] oops_end at ffffffff8168ef88 #4 [ffff88085c143c38] no_context at ffffffff8167ebb3 #5 [ffff88085c143c88] __bad_area_nosemaphore at ffffffff8167ec49 #6 [ffff88085c143cd0] bad_area_nosemaphore at ffffffff8167edb3 #7 [ffff88085c143ce0] __do_page_fault at ffffffff81691d1e #8 [ffff88085c143d40] do_page_fault at ffffffff81691ec5 #9 [ffff88085c143d70] page_fault at ffffffff8168e188 [exception RIP: unknown or invalid address] RIP: ffffffffa053c800 RSP: ffff88085c143e28 RFLAGS: 00010206 RAX: ffff88017c72bfd8 RBX: ffff88017a8dc000 RCX: ffff8810588b5ac8 RDX: ffff8810588b5a00 RSI: ffffffffa053c800 RDI: ffff8810588b5a00 RBP: ffff88085c143e58 R8: ffff88017c70d408 R9: ffff88017a8dc000 R10: 0000000000000002 R11: ffff88085c143da0 R12: ffff8810588b5ac8 R13: 0000000000000100 R14: ffffffffa053c800 R15: ffff8810588b5a00 ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018 <IRQ stack> [exception RIP: cpuidle_enter_state+82] RIP: ffffffff81514192 RSP: ffff88017c72be50 RFLAGS: 00000202 RAX: 0000001e4c3c6f16 RBX: 000000000000f8a0 RCX: 0000000000000018 RDX: 0000000225c17d03 RSI: ffff88017c72bfd8 RDI: 0000001e4c3c6f16 RBP: ffff88017c72be78 R8: 000000000000237e R9: 0000000000000018 R10: 0000000000002494 R11: 0000000000000001 R12: ffff88017c72be20 R13: ffff88085c14f8e0 R14: 0000000000000082 R15: 0000001e4c3bb400 ORIG_RAX: ffffffffffffff10 CS: 0010 SS: 0018 This is the corresponding stack trace It has crashed because the area pointed with RIP extracted from timer element is already removed during a shutdown process. The function is smi_timeout(). And we think ffff8810588b5a00 in RDX is a parameter struct smi_info crash> rd ffff8810588b5a00 20 ffff8810588b5a00: ffff8810588b6000 0000000000000000 .`.X............ ffff8810588b5a10: ffff880853264400 ffffffffa05417e0 .D&S......T..... ffff8810588b5a20: 24a024a000000000 0000000000000000 .....$.$........ ffff8810588b5a30: 0000000000000000 0000000000000000 ................ ffff8810588b5a30: 0000000000000000 0000000000000000 ................ ffff8810588b5a40: ffffffffa053a040 ffffffffa053a060 @.S.....`.S..... ffff8810588b5a50: 0000000000000000 0000000100000001 ................ ffff8810588b5a60: 0000000000000000 0000000000000e00 ................ ffff8810588b5a70: ffffffffa053a580 ffffffffa053a6e0 ..S.......S..... ffff8810588b5a80: ffffffffa053a4a0 ffffffffa053a250 ..S.....P.S..... ffff8810588b5a90: 0000000500000002 0000000000000000 ................ Unfortunately the top of this area is already detroyed by someone. But because of two reasonns we think this is struct smi_info 1) The address included in between ffff8810588b5a70 and ffff8810588b5a80: are inside of ipmi_si_intf.c see crash> module ffff88085779d2c0 2) We've found the area which point this. It is offset 0x68 of ffff880859df4000 crash> rd ffff880859df4000 100 ffff880859df4000: 0000000000000000 0000000000000001 ................ ffff880859df4010: ffffffffa0535290 dead000000000200 .RS............. ffff880859df4020: ffff880859df4020 ffff880859df4020 @.Y.... @.Y.... ffff880859df4030: 0000000000000002 0000000000100010 ................ ffff880859df4040: ffff880859df4040 ffff880859df4040 @@.Y....@@.Y.... ffff880859df4050: 0000000000000000 0000000000000000 ................ ffff880859df4060: 0000000000000000 ffff8810588b5a00 .........Z.X.... ffff880859df4070: 0000000000000001 ffff880859df4078 [email protected].... If we regards it as struct ipmi_smi in shutdown process it looks consistent. The remedy for this apparent race is affixed below. Signed-off-by: Tony Camuso <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]> This was first introduced in 7ea0ed2 ipmi: Make the message handler easier to use for SMI interfaces where some code was moved outside of the rcu_read_lock() and the lock was not added. Signed-off-by: Corey Minyard <[email protected]>

According to the dwc2 programmer's guide v3.10a, in '2.1.3.2 Dedicated FIFO Mode with No Thresholding', it suggested that: Device RxFIFO = - Scatter/Gather DMA mode: (4 * number of control endpoints + 6) + ((largest USB packet used / 4) + 1 for status information) + (2 * number of OUT endpoints) + 1 for Global NAK on rockchip platforms: (4 * 1 + 6) + ((1024 / 4) + 1) + (2 * 6) + 1 = 280 - Slave or Buffer DMA mode: (5 * number of control endpoints + 8) + ((largest USB packet used / 4) + 1 for status information) + (2 * number of OUT endpoints) + 1 for Global NAK on rockchip platforms: (5 * 1 + 8) + ((1024 / 4) + 1) + (2 * 6) + 1 = 283 Device IN Endpoint TxFIFO = The TxFIFO must equal at least one MaxPacketSize (MPS). In addition to RxFIFO and TxFIFOs, refer to dwc2 databook v3.10a, 'Figure 2-13 Device Mode FIFO Address Mapping and AHB FIFO Access Mapping (Dedicated FIFO)', it required that when the device is operating in non Scatter Gather Internal DMA mode, the last locations of the SPRAM are used to store the DMAADDR values for each Endpoint (1 location per endpoint). When the device is operating in Scatter Gather mode, then the last locations of the SPRAM store the Base Descriptor address, Current Descriptor address, Current Buffer address, and status quadlet information for each endpoint direction (4 locations per Endpoint). If an Endpoint is bidirectional , then 4 locations will be used for IN, and another 4 for OUT). Considering that the total FIFO size of dwc2 otg is 0x3cc (972), and we must reserve (4 * 13) = 52 locations for all Endpoints. So reconfig dwc2 device fifo size as follows: Device RxFIFO = 280 Device IN Endpoint TxFIFO - FIFO #0 = (64 / 4) = 16 (Assuming this is used for EP0) - FIFO #1 = (1024/4) = 256 (Assuming this is used for Isochronous) - FIFO #2 = (512/4) = 128 - FIFO #3 = (512/4) = 128 - FIFO #4 = (256/4) = 64 - FIFO #5 = (128/4) = 32 - FIFO #6 = (64/4) = 16 After reconfig the dwc2 device fifo size, test mtp write on rockchip platform (PC -> rockchip platform) on rk312x/rk3326/px30/rk3288 evb, when mask the 'vfs_write' in f_mtp.c, the writing data rate can be increased from 16MBps ~ 20MBps to 30MBps ~ 36MBps on different kinds of rockchip evbs. Change-Id: Icdf8a5dd95f96d174233e4ffc765c9a982b9f0b6 Signed-off-by: William Wu <[email protected]>

According to the dwc2 programmer's guide v3.10a, in '2.1.3.2 Dedicated FIFO Mode with No Thresholding', it suggested that: Device RxFIFO = - Scatter/Gather DMA mode: (4 * number of control endpoints + 6) + ((largest USB packet used / 4) + 1 for status information) + (2 * number of OUT endpoints) + 1 for Global NAK on rockchip platforms: (4 * 1 + 6) + ((1024 / 4) + 1) + (2 * 6) + 1 = 280 - Slave or Buffer DMA mode: (5 * number of control endpoints + 8) + ((largest USB packet used / 4) + 1 for status information) + (2 * number of OUT endpoints) + 1 for Global NAK on rockchip platforms: (5 * 1 + 8) + ((1024 / 4) + 1) + (2 * 6) + 1 = 283 Device IN Endpoint TxFIFO = The TxFIFO must equal at least one MaxPacketSize (MPS). In addition to RxFIFO and TxFIFOs, refer to dwc2 databook v3.10a, 'Figure 2-13 Device Mode FIFO Address Mapping and AHB FIFO Access Mapping (Dedicated FIFO)', it required that when the device is operating in non Scatter Gather Internal DMA mode, the last locations of the SPRAM are used to store the DMAADDR values for each Endpoint (1 location per endpoint). When the device is operating in Scatter Gather mode, then the last locations of the SPRAM store the Base Descriptor address, Current Descriptor address, Current Buffer address, and status quadlet information for each endpoint direction (4 locations per Endpoint). If an Endpoint is bidirectional , then 4 locations will be used for IN, and another 4 for OUT). Considering that the total FIFO size of dwc2 otg is 0x3cc (972), and we must reserve (4 * 13) = 52 locations for all Endpoints. So reconfig dwc2 device fifo size as follows: Device RxFIFO = 280 Device IN Endpoint TxFIFO - FIFO #0 = (64 / 4) = 16 (Assuming this is used for EP0) - FIFO #1 = (1024/4) = 256 (Assuming this is used for Isochronous) - FIFO #2 = (512/4) = 128 - FIFO #3 = (512/4) = 128 - FIFO #4 = (256/4) = 64 - FIFO #5 = (128/4) = 32 - FIFO #6 = (64/4) = 16 After reconfig the dwc2 device fifo size, test mtp write on rockchip platform (PC -> rockchip platform) on rk312x/rk3326/px30/rk3288 evb, when mask the 'vfs_write' in f_mtp.c, the writing data rate can be increased from 16MBps ~ 20MBps to 30MBps ~ 36MBps on different kinds of rockchip evbs. Change-Id: I52c64a279523c811f706e69e427b0a6e8c45683b Signed-off-by: William Wu <[email protected]>

[ Upstream commit 42ffb0b] There exists a deadlock with range_cyclic that has existed forever. If we loop around with a bio already built we could deadlock with a writer who has the page locked that we're attempting to write but is waiting on a page in our bio to be written out. The task traces are as follows PID: 1329874 TASK: ffff889ebcdf3800 CPU: 33 COMMAND: "kworker/u113:5" #0 [ffffc900297bb658] __schedule at ffffffff81a4c33f #1 [ffffc900297bb6e0] schedule at ffffffff81a4c6e3 #2 [ffffc900297bb6f8] io_schedule at ffffffff81a4ca42 #3 [ffffc900297bb708] __lock_page at ffffffff811f145b #4 [ffffc900297bb798] __process_pages_contig at ffffffff814bc502 khadas#5 [ffffc900297bb8c8] lock_delalloc_pages at ffffffff814bc684 khadas#6 [ffffc900297bb900] find_lock_delalloc_range at ffffffff814be9ff khadas#7 [ffffc900297bb9a0] writepage_delalloc at ffffffff814bebd0 khadas#8 [ffffc900297bba18] __extent_writepage at ffffffff814bfbf2 khadas#9 [ffffc900297bba98] extent_write_cache_pages at ffffffff814bffbd PID: 2167901 TASK: ffff889dc6a59c00 CPU: 14 COMMAND: "aio-dio-invalid" #0 [ffffc9003b50bb18] __schedule at ffffffff81a4c33f #1 [ffffc9003b50bba0] schedule at ffffffff81a4c6e3 #2 [ffffc9003b50bbb8] io_schedule at ffffffff81a4ca42 #3 [ffffc9003b50bbc8] wait_on_page_bit at ffffffff811f24d6 #4 [ffffc9003b50bc60] prepare_pages at ffffffff814b05a7 khadas#5 [ffffc9003b50bcd8] btrfs_buffered_write at ffffffff814b1359 khadas#6 [ffffc9003b50bdb0] btrfs_file_write_iter at ffffffff814b5933 khadas#7 [ffffc9003b50be38] new_sync_write at ffffffff8128f6a8 khadas#8 [ffffc9003b50bec8] vfs_write at ffffffff81292b9d khadas#9 [ffffc9003b50bf00] ksys_pwrite64 at ffffffff81293032 I used drgn to find the respective pages we were stuck on page_entry.page 0xffffea00fbfc7500 index 8148 bit 15 pid 2167901 page_entry.page 0xffffea00f9bb7400 index 7680 bit 0 pid 1329874 As you can see the kworker is waiting for bit 0 (PG_locked) on index 7680, and aio-dio-invalid is waiting for bit 15 (PG_writeback) on index 8148. aio-dio-invalid has 7680, and the kworker epd looks like the following crash> struct extent_page_data ffffc900297bbbb0 struct extent_page_data { bio = 0xffff889f747ed830, tree = 0xffff889eed6ba448, extent_locked = 0, sync_io = 0 } Probably worth mentioning as well that it waits for writeback of the page to complete while holding a lock on it (at prepare_pages()). Using drgn I walked the bio pages looking for page 0xffffea00fbfc7500 which is the one we're waiting for writeback on bio = Object(prog, 'struct bio', address=0xffff889f747ed830) for i in range(0, bio.bi_vcnt.value_()): bv = bio.bi_io_vec[i] if bv.bv_page.value_() == 0xffffea00fbfc7500: print("FOUND IT") which validated what I suspected. The fix for this is simple, flush the epd before we loop back around to the beginning of the file during writeout. Fixes: b293f02 ("Btrfs: Add writepages support") CC: [email protected] # 4.4+ Reviewed-by: Filipe Manana <[email protected]> Signed-off-by: Josef Bacik <[email protected]> Signed-off-by: David Sterba <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 76e7527 ] Some servers seem to accept connections while booting but never send the SMBNegotiate response neither close the connection, causing all processes accessing the share hang on uninterruptible sleep state. This happens when the cifs_demultiplex_thread detects the server is unresponsive so releases the socket and start trying to reconnect. At some point, the faulty server will accept the socket and the TCP status will be set to NeedNegotiate. The first issued command accessing the share will start the negotiation (pid 5828 below), but the response will never arrive so other commands will be blocked waiting on the mutex (pid 55352). This patch checks for unresponsive servers also on the negotiate stage releasing the socket and reconnecting if the response is not received and checking again the tcp state when the mutex is acquired. PID: 55352 TASK: ffff880fd6cc02c0 CPU: 0 COMMAND: "ls" #0 [ffff880fd9add9f0] schedule at ffffffff81467eb9 #1 [ffff880fd9addb38] __mutex_lock_slowpath at ffffffff81468fe0 #2 [ffff880fd9addba8] mutex_lock at ffffffff81468b1a #3 [ffff880fd9addbc0] cifs_reconnect_tcon at ffffffffa042f905 [cifs] #4 [ffff880fd9addc60] smb_init at ffffffffa042faeb [cifs] khadas#5 [ffff880fd9addca0] CIFSSMBQPathInfo at ffffffffa04360b5 [cifs] .... Which is waiting a mutex owned by: PID: 5828 TASK: ffff880fcc55e400 CPU: 0 COMMAND: "xxxx" #0 [ffff880fbfdc19b8] schedule at ffffffff81467eb9 #1 [ffff880fbfdc1b00] wait_for_response at ffffffffa044f96d [cifs] #2 [ffff880fbfdc1b60] SendReceive at ffffffffa04505ce [cifs] #3 [ffff880fbfdc1bb0] CIFSSMBNegotiate at ffffffffa0438d79 [cifs] #4 [ffff880fbfdc1c50] cifs_negotiate_protocol at ffffffffa043b383 [cifs] khadas#5 [ffff880fbfdc1c80] cifs_reconnect_tcon at ffffffffa042f911 [cifs] khadas#6 [ffff880fbfdc1d20] smb_init at ffffffffa042faeb [cifs] khadas#7 [ffff880fbfdc1d60] CIFSSMBQFSInfo at ffffffffa0434eb0 [cifs] .... Signed-off-by: Samuel Cabrero <[email protected]> Reviewed-by: Aurélien Aptel <[email protected]> Reviewed-by: Ronnie Sahlberg <[email protected]> Signed-off-by: Steve French <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 9b38cc7 ] Ziqian reported lockup when adding retprobe on _raw_spin_lock_irqsave. My test was also able to trigger lockdep output: ============================================ WARNING: possible recursive locking detected 5.6.0-rc6+ #6 Not tainted -------------------------------------------- sched-messaging/2767 is trying to acquire lock: ffffffff9a492798 (&(kretprobe_table_locks[i].lock)){-.-.}, at: kretprobe_hash_lock+0x52/0xa0 but task is already holding lock: ffffffff9a491a18 (&(kretprobe_table_locks[i].lock)){-.-.}, at: kretprobe_trampoline+0x0/0x50 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&(kretprobe_table_locks[i].lock)); lock(&(kretprobe_table_locks[i].lock)); *** DEADLOCK *** May be due to missing lock nesting notation 1 lock held by sched-messaging/2767: #0: ffffffff9a491a18 (&(kretprobe_table_locks[i].lock)){-.-.}, at: kretprobe_trampoline+0x0/0x50 stack backtrace: CPU: 3 PID: 2767 Comm: sched-messaging Not tainted 5.6.0-rc6+ #6 Call Trace: dump_stack+0x96/0xe0 __lock_acquire.cold.57+0x173/0x2b7 ? native_queued_spin_lock_slowpath+0x42b/0x9e0 ? lockdep_hardirqs_on+0x590/0x590 ? __lock_acquire+0xf63/0x4030 lock_acquire+0x15a/0x3d0 ? kretprobe_hash_lock+0x52/0xa0 _raw_spin_lock_irqsave+0x36/0x70 ? kretprobe_hash_lock+0x52/0xa0 kretprobe_hash_lock+0x52/0xa0 trampoline_handler+0xf8/0x940 ? kprobe_fault_handler+0x380/0x380 ? find_held_lock+0x3a/0x1c0 kretprobe_trampoline+0x25/0x50 ? lock_acquired+0x392/0xbc0 ? _raw_spin_lock_irqsave+0x50/0x70 ? __get_valid_kprobe+0x1f0/0x1f0 ? _raw_spin_unlock_irqrestore+0x3b/0x40 ? finish_task_switch+0x4b9/0x6d0 ? __switch_to_asm+0x34/0x70 ? __switch_to_asm+0x40/0x70 The code within the kretprobe handler checks for probe reentrancy, so we won't trigger any _raw_spin_lock_irqsave probe in there. The problem is in outside kprobe_flush_task, where we call: kprobe_flush_task kretprobe_table_lock raw_spin_lock_irqsave _raw_spin_lock_irqsave where _raw_spin_lock_irqsave triggers the kretprobe and installs kretprobe_trampoline handler on _raw_spin_lock_irqsave return. The kretprobe_trampoline handler is then executed with already locked kretprobe_table_locks, and first thing it does is to lock kretprobe_table_locks ;-) the whole lockup path like: kprobe_flush_task kretprobe_table_lock raw_spin_lock_irqsave _raw_spin_lock_irqsave ---> probe triggered, kretprobe_trampoline installed ---> kretprobe_table_locks locked kretprobe_trampoline trampoline_handler kretprobe_hash_lock(current, &head, &flags); <--- deadlock Adding kprobe_busy_begin/end helpers that mark code with fake probe installed to prevent triggering of another kprobe within this code. Using these helpers in kprobe_flush_task, so the probe recursion protection check is hit and the probe is never set to prevent above lockup. Link: http://lkml.kernel.org/r/158927059835.27680.7011202830041561604.stgit@devnote2 Fixes: ef53d9c ("kprobes: improve kretprobe scalability with hashed locking") Cc: Ingo Molnar <[email protected]> Cc: "Gustavo A . R . Silva" <[email protected]> Cc: Anders Roxell <[email protected]> Cc: "Naveen N . Rao" <[email protected]> Cc: Anil S Keshavamurthy <[email protected]> Cc: David Miller <[email protected]> Cc: Ingo Molnar <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: [email protected] Reported-by: "Ziqian SUN (Zamir)" <[email protected]> Acked-by: Masami Hiramatsu <[email protected]> Signed-off-by: Jiri Olsa <[email protected]> Signed-off-by: Steven Rostedt (VMware) <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit 8523c00 ] After entering kdb due to breakpoint, when we execute 'ss' or 'go' (will delay installing breakpoints, do single-step first), it won't work correctly, and it will enter kdb due to oops. It's because the reason gotten in kdb_stub() is not as expected, and it seems that the ex_vector for single-step should be 0, like what arch powerpc/sh/parisc has implemented. Before the patch: Entering kdb (current=0xffff8000119e2dc0, pid 0) on processor 0 due to Keyboard Entry [0]kdb> bp printk Instruction(i) BP #0 at 0xffff8000101486cc (printk) is enabled addr at ffff8000101486cc, hardtype=0 installed=0 [0]kdb> g / # echo h > /proc/sysrq-trigger Entering kdb (current=0xffff0000fa878040, pid 266) on processor 3 due to Breakpoint @ 0xffff8000101486cc [3]kdb> ss Entering kdb (current=0xffff0000fa878040, pid 266) on processor 3 Oops: (null) due to oops @ 0xffff800010082ab8 CPU: 3 PID: 266 Comm: sh Not tainted 5.7.0-rc4-13839-gf0e5ad491718 #6 Hardware name: linux,dummy-virt (DT) pstate: 00000085 (nzcv daIf -PAN -UAO) pc : el1_irq+0x78/0x180 lr : __handle_sysrq+0x80/0x190 sp : ffff800015003bf0 x29: ffff800015003d20 x28: ffff0000fa878040 x27: 0000000000000000 x26: ffff80001126b1f0 x25: ffff800011b6a0d8 x24: 0000000000000000 x23: 0000000080200005 x22: ffff8000101486cc x21: ffff800015003d30 x20: 0000ffffffffffff x19: ffff8000119f2000 x18: 0000000000000000 x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000 x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000 x8 : ffff800015003e50 x7 : 0000000000000002 x6 : 00000000380b9990 x5 : ffff8000106e99e8 x4 : ffff0000fadd83c0 x3 : 0000ffffffffffff x2 : ffff800011b6a0d8 x1 : ffff800011b6a000 x0 : ffff80001130c9d8 Call trace: el1_irq+0x78/0x180 printk+0x0/0x84 write_sysrq_trigger+0xb0/0x118 proc_reg_write+0xb4/0xe0 __vfs_write+0x18/0x40 vfs_write+0xb0/0x1b8 ksys_write+0x64/0xf0 __arm64_sys_write+0x14/0x20 el0_svc_common.constprop.2+0xb0/0x168 do_el0_svc+0x20/0x98 el0_sync_handler+0xec/0x1a8 el0_sync+0x140/0x180 [3]kdb> After the patch: Entering kdb (current=0xffff8000119e2dc0, pid 0) on processor 0 due to Keyboard Entry [0]kdb> bp printk Instruction(i) BP #0 at 0xffff8000101486cc (printk) is enabled addr at ffff8000101486cc, hardtype=0 installed=0 [0]kdb> g / # echo h > /proc/sysrq-trigger Entering kdb (current=0xffff0000fa852bc0, pid 268) on processor 0 due to Breakpoint @ 0xffff8000101486cc [0]kdb> g Entering kdb (current=0xffff0000fa852bc0, pid 268) on processor 0 due to Breakpoint @ 0xffff8000101486cc [0]kdb> ss Entering kdb (current=0xffff0000fa852bc0, pid 268) on processor 0 due to SS trap @ 0xffff800010082ab8 [0]kdb> Fixes: 44679a4 ("arm64: KGDB: Add step debugging support") Signed-off-by: Wei Li <[email protected]> Tested-by: Douglas Anderson <[email protected]> Reviewed-by: Douglas Anderson <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Will Deacon <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

Khadas edge 4.4.y

[ Upstream commit e24c644 ] I compiled with AddressSanitizer and I had these memory leaks while I was using the tep_parse_format function: Direct leak of 28 byte(s) in 4 object(s) allocated from: #0 0x7fb07db49ffe in __interceptor_realloc (/lib/x86_64-linux-gnu/libasan.so.5+0x10dffe) #1 0x7fb07a724228 in extend_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:985 #2 0x7fb07a724c21 in __read_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1140 #3 0x7fb07a724f78 in read_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1206 #4 0x7fb07a725191 in __read_expect_type /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1291 #5 0x7fb07a7251df in read_expect_type /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1299 #6 0x7fb07a72e6c8 in process_dynamic_array_len /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:2849 #7 0x7fb07a7304b8 in process_function /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3161 #8 0x7fb07a730900 in process_arg_token /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3207 #9 0x7fb07a727c0b in process_arg /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:1786 #10 0x7fb07a731080 in event_read_print_args /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3285 #11 0x7fb07a731722 in event_read_print /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:3369 #12 0x7fb07a740054 in __tep_parse_format /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6335 #13 0x7fb07a74047a in __parse_event /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6389 #14 0x7fb07a740536 in tep_parse_format /home/pduplessis/repo/linux/tools/lib/traceevent/event-parse.c:6431 #15 0x7fb07a785acf in parse_event ../../../src/fs-src/fs.c:251 #16 0x7fb07a785ccd in parse_systems ../../../src/fs-src/fs.c:284 #17 0x7fb07a786fb3 in read_metadata ../../../src/fs-src/fs.c:593 #18 0x7fb07a78760e in ftrace_fs_source_init ../../../src/fs-src/fs.c:727 #19 0x7fb07d90c19c in add_component_with_init_method_data ../../../../src/lib/graph/graph.c:1048 #20 0x7fb07d90c87b in add_source_component_with_initialize_method_data ../../../../src/lib/graph/graph.c:1127 #21 0x7fb07d90c92a in bt_graph_add_source_component ../../../../src/lib/graph/graph.c:1152 #22 0x55db11aa632e in cmd_run_ctx_create_components_from_config_components ../../../src/cli/babeltrace2.c:2252 #23 0x55db11aa6fda in cmd_run_ctx_create_components ../../../src/cli/babeltrace2.c:2347 #24 0x55db11aa780c in cmd_run ../../../src/cli/babeltrace2.c:2461 #25 0x55db11aa8a7d in main ../../../src/cli/babeltrace2.c:2673 #26 0x7fb07d5460b2 in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x270b2) The token variable in the process_dynamic_array_len function is allocated in the read_expect_type function, but is not freed before calling the read_token function. Free the token variable before calling read_token in order to plug the leak. Signed-off-by: Philippe Duplessis-Guindon <[email protected]> Reviewed-by: Steven Rostedt (VMware) <[email protected]> Link: https://lore.kernel.org/linux-trace-devel/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

[ Upstream commit d26383d ] The following leaks were detected by ASAN: Indirect leak of 360 byte(s) in 9 object(s) allocated from: #0 0x7fecc305180e in calloc (/lib/x86_64-linux-gnu/libasan.so.5+0x10780e) #1 0x560578f6dce5 in perf_pmu__new_format util/pmu.c:1333 #2 0x560578f752fc in perf_pmu_parse util/pmu.y:59 #3 0x560578f6a8b7 in perf_pmu__format_parse util/pmu.c:73 #4 0x560578e07045 in test__pmu tests/pmu.c:155 #5 0x560578de109b in run_test tests/builtin-test.c:410 #6 0x560578de109b in test_and_print tests/builtin-test.c:440 #7 0x560578de401a in __cmd_test tests/builtin-test.c:661 #8 0x560578de401a in cmd_test tests/builtin-test.c:807 #9 0x560578e49354 in run_builtin /home/namhyung/project/linux/tools/perf/perf.c:312 #10 0x560578ce71a8 in handle_internal_command /home/namhyung/project/linux/tools/perf/perf.c:364 #11 0x560578ce71a8 in run_argv /home/namhyung/project/linux/tools/perf/perf.c:408 #12 0x560578ce71a8 in main /home/namhyung/project/linux/tools/perf/perf.c:538 #13 0x7fecc2b7acc9 in __libc_start_main ../csu/libc-start.c:308 Fixes: cff7f95 ("perf tests: Move pmu tests into separate object") Signed-off-by: Namhyung Kim <[email protected]> Acked-by: Jiri Olsa <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Mark Rutland <[email protected]> Cc: Peter Zijlstra <[email protected]> Cc: Stephane Eranian <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]> Signed-off-by: Sasha Levin <[email protected]>

…lock_t for PREEMPT_RT <3>[ 141.648698][ C0] BUG: sleeping function called from invalid context at kernel/locking/rtmutex.c:970 <3>[ 141.648723][ C0] in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 0, name: swapper/0 <4>[ 141.648739][ C0] INFO: lockdep is turned off. <4>[ 141.648745][ C0] irq event stamp: 22142 <4>[ 141.648751][ C0] hardirqs last enabled at (22141): [<ffffffc010139a98>] tick_nohz_idle_exit+0x90/0x134 <4>[ 141.648785][ C0] hardirqs last disabled at (22142): [<ffffffc01139fdd8>] __schedule+0x80/0x6d4 <4>[ 141.648812][ C0] softirqs last enabled at (2818): [<ffffffc010056c20>] __local_bh_enable_ip+0x1f4/0x258 <4>[ 141.648840][ C0] softirqs last disabled at (2812): [<ffffffc01015f654>] local_bh_disable+0x4/0x30 <3>[ 141.648867][ C0] Preemption disabled at: <3>[ 141.648872][ C0] [<ffffffc0113a0570>] schedule_preempt_disabled+0x20/0x2c <4>[ 141.648900][ C0] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.10.66-rt53 #6 <4>[ 141.648918][ C0] Hardware name: Rockchip RK3588 EVB1 LP4 V10 Board (DT) <4>[ 141.648927][ C0] Call trace: <4>[ 141.648932][ C0] dump_backtrace+0x0/0x1c4 <4>[ 141.648956][ C0] show_stack+0x18/0x24 <4>[ 141.648977][ C0] dump_stack_lvl+0xec/0x148 <4>[ 141.648993][ C0] dump_stack+0x18/0x64 <4>[ 141.649008][ C0] ___might_sleep+0x1b4/0x1c4 <4>[ 141.649030][ C0] rt_spin_lock+0x70/0xd8 <4>[ 141.649046][ C0] log_abnormal_wakeup_reason+0x64/0xd8 <4>[ 141.649066][ C0] handle_fasteoi_irq+0x224/0x228 <4>[ 141.649084][ C0] __handle_domain_irq+0xb0/0x11c <4>[ 141.649105][ C0] gic_handle_irq+0x74/0x14c <4>[ 141.649123][ C0] el1_irq+0xd0/0x1c0 <4>[ 141.649138][ C0] cpuidle_enter_state+0x184/0x2d0 <4>[ 141.649156][ C0] cpuidle_enter+0x38/0x50 <4>[ 141.649170][ C0] cpuidle_idle_call+0x188/0x278 <4>[ 141.649189][ C0] do_idle+0xb8/0x10c <4>[ 141.649205][ C0] cpu_startup_entry+0x24/0x28 <4>[ 141.649222][ C0] rest_init+0x1ec/0x1fc <4>[ 141.649240][ C0] arch_call_rest_init+0x10/0x1c <4>[ 141.649260][ C0] start_kernel+0x3f0/0x524 Signed-off-by: Liang Chen <[email protected]> Change-Id: I383164b2a646250d34dc7c085e7a1d297889581e

Fix tcon use-after-free and NULL ptr deref. Customer system crashes with the following kernel log: [462233.169868] CIFS VFS: Cancelling wait for mid 4894753 cmd: 14 => a QUERY DIR [462233.228045] CIFS VFS: cifs_put_smb_ses: Session Logoff failure rc=-4 [462233.305922] CIFS VFS: cifs_put_smb_ses: Session Logoff failure rc=-4 [462233.306205] CIFS VFS: cifs_put_smb_ses: Session Logoff failure rc=-4 [462233.347060] CIFS VFS: cifs_put_smb_ses: Session Logoff failure rc=-4 [462233.347107] CIFS VFS: Close unmatched open [462233.347113] BUG: unable to handle kernel NULL pointer dereference at 0000000000000038 ... [exception RIP: cifs_put_tcon+0xa0] (this is doing tcon->ses->server) #6 [...] smb2_cancelled_close_fid at ... [cifs] #7 [...] process_one_work at ... #8 [...] worker_thread at ... #9 [...] kthread at ... The most likely explanation we have is: * When we put the last reference of a tcon (refcount=0), we close the cached share root handle. * If closing a handle is interrupted, SMB2_close() will queue a SMB2_close() in a work thread. * The queued object keeps a tcon ref so we bump the tcon refcount, jumping from 0 to 1. * We reach the end of cifs_put_tcon(), we free the tcon object despite it now having a refcount of 1. * The queued work now runs, but the tcon, ses & server was freed in the meantime resulting in a crash. THREAD 1 ======== cifs_put_tcon => tcon refcount reach 0 SMB2_tdis close_shroot_lease close_shroot_lease_locked => if cached root has lease && refcount = 0 smb2_close_cached_fid => if cached root valid SMB2_close => retry close in a thread if interrupted smb2_handle_cancelled_close __smb2_handle_cancelled_close => !! tcon refcount bump 0 => 1 !! INIT_WORK(&cancelled->work, smb2_cancelled_close_fid); queue_work(cifsiod_wq, &cancelled->work) => queue work tconInfoFree(tcon); ==> freed! cifs_put_smb_ses(ses); ==> freed! THREAD 2 (workqueue) ======== smb2_cancelled_close_fid SMB2_close(0, cancelled->tcon, ...); => use-after-free of tcon cifs_put_tcon(cancelled->tcon); => tcon refcount reach 0 second time *CRASH* Fixes: d919131 ("CIFS: Close cached root handle only if it has a lease") Signed-off-by: Aurelien Aptel <[email protected]> Signed-off-by: Steve French <[email protected]> Reviewed-by: Pavel Shilovsky <[email protected]>

With commit c4cb231 ("iommu/amd: Add support for enable/disable IOPF") we are hitting below issue. This happens because in IOPF enablement path it holds spin lock with irq disable and then tries to take mutex lock. dmesg: ----- [ 0.938739] ============================= [ 0.938740] [ BUG: Invalid wait context ] [ 0.938742] 6.10.0-rc1+ khadas#1 Not tainted [ 0.938745] ----------------------------- [ 0.938746] swapper/0/1 is trying to lock: [ 0.938748] ffffffff8c9f01d8 (&port_lock_key){....}-{3:3}, at: serial8250_console_write+0x78/0x4a0 [ 0.938767] other info that might help us debug this: [ 0.938768] context-{5:5} [ 0.938769] 7 locks held by swapper/0/1: [ 0.938772] #0: ffff888101a91310 (&group->mutex){+.+.}-{4:4}, at: bus_iommu_probe+0x70/0x160 [ 0.938790] khadas#1: ffff888101d1f1b8 (&domain->lock){....}-{3:3}, at: amd_iommu_attach_device+0xa5/0x700 [ 0.938799] khadas#2: ffff888101cc3d18 (&dev_data->lock){....}-{3:3}, at: amd_iommu_attach_device+0xc5/0x700 [ 0.938806] khadas#3: ffff888100052830 (&iommu->lock){....}-{2:2}, at: amd_iommu_iopf_add_device+0x3f/0xa0 [ 0.938813] khadas#4: ffffffff8945a340 (console_lock){+.+.}-{0:0}, at: _printk+0x48/0x50 [ 0.938822] khadas#5: ffffffff8945a390 (console_srcu){....}-{0:0}, at: console_flush_all+0x58/0x4e0 [ 0.938867] khadas#6: ffffffff82459f80 (console_owner){....}-{0:0}, at: console_flush_all+0x1f0/0x4e0 [ 0.938872] stack backtrace: [ 0.938874] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 6.10.0-rc1+ khadas#1 [ 0.938877] Hardware name: HP HP EliteBook 745 G3/807E, BIOS N73 Ver. 01.39 04/16/2019 Fix above issue by re-arranging code in attach device path: - move device PASID/IOPF enablement outside lock in AMD IOMMU driver. This is safe as core layer holds group->mutex lock before calling iommu_ops->attach_dev. Reported-by: Borislav Petkov <[email protected]> Reported-by: Mikhail Gavrilov <[email protected]> Reported-by: Chris Bainbridge <[email protected]> Fixes: c4cb231 ("iommu/amd: Add support for enable/disable IOPF") Tested-by: Borislav Petkov <[email protected]> Tested-by: Chris Bainbridge <[email protected]> Tested-by: Mikhail Gavrilov <[email protected]> Signed-off-by: Vasant Hegde <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Joerg Roedel <[email protected]>

…PLES event" This reverts commit 7d1405c. This causes segfaults in some cases, as reported by Milian: ``` sudo /usr/bin/perf record -z --call-graph dwarf -e cycles -e raw_syscalls:sys_enter ls ... [ perf record: Woken up 3 times to write data ] malloc(): invalid next size (unsorted) Aborted ``` Backtrace with GDB + debuginfod: ``` malloc(): invalid next size (unsorted) Thread 1 "perf" received signal SIGABRT, Aborted. __pthread_kill_implementation (threadid=<optimized out>, signo=signo@entry=6, no_tid=no_tid@entry=0) at pthread_kill.c:44 Downloading source file /usr/src/debug/glibc/glibc/nptl/pthread_kill.c 44 return INTERNAL_SYSCALL_ERROR_P (ret) ? INTERNAL_SYSCALL_ERRNO (ret) : 0; (gdb) bt #0 __pthread_kill_implementation (threadid=<optimized out>, signo=signo@entry=6, no_tid=no_tid@entry=0) at pthread_kill.c:44 khadas#1 0x00007ffff6ea8eb3 in __pthread_kill_internal (threadid=<optimized out>, signo=6) at pthread_kill.c:78 khadas#2 0x00007ffff6e50a30 in __GI_raise (sig=sig@entry=6) at ../sysdeps/posix/ raise.c:26 khadas#3 0x00007ffff6e384c3 in __GI_abort () at abort.c:79 khadas#4 0x00007ffff6e39354 in __libc_message_impl (fmt=fmt@entry=0x7ffff6fc22ea "%s\n") at ../sysdeps/posix/libc_fatal.c:132 khadas#5 0x00007ffff6eb3085 in malloc_printerr (str=str@entry=0x7ffff6fc5850 "malloc(): invalid next size (unsorted)") at malloc.c:5772 khadas#6 0x00007ffff6eb657c in _int_malloc (av=av@entry=0x7ffff6ff6ac0 <main_arena>, bytes=bytes@entry=368) at malloc.c:4081 khadas#7 0x00007ffff6eb877e in __libc_calloc (n=<optimized out>, elem_size=<optimized out>) at malloc.c:3754 khadas#8 0x000055555569bdb6 in perf_session.do_write_header () khadas#9 0x00005555555a373a in __cmd_record.constprop.0 () khadas#10 0x00005555555a6846 in cmd_record () khadas#11 0x000055555564db7f in run_builtin () khadas#12 0x000055555558ed77 in main () ``` Valgrind memcheck: ``` ==45136== Invalid write of size 8 ==45136== at 0x2B38A5: perf_event__synthesize_id_sample (in /usr/bin/perf) ==45136== by 0x157069: __cmd_record.constprop.0 (in /usr/bin/perf) ==45136== by 0x15A845: cmd_record (in /usr/bin/perf) ==45136== by 0x201B7E: run_builtin (in /usr/bin/perf) ==45136== by 0x142D76: main (in /usr/bin/perf) ==45136== Address 0x6a866a8 is 0 bytes after a block of size 40 alloc'd ==45136== at 0x4849BF3: calloc (vg_replace_malloc.c:1675) ==45136== by 0x3574AB: zalloc (in /usr/bin/perf) ==45136== by 0x1570E0: __cmd_record.constprop.0 (in /usr/bin/perf) ==45136== by 0x15A845: cmd_record (in /usr/bin/perf) ==45136== by 0x201B7E: run_builtin (in /usr/bin/perf) ==45136== by 0x142D76: main (in /usr/bin/perf) ==45136== ==45136== Syscall param write(buf) points to unaddressable byte(s) ==45136== at 0x575953D: __libc_write (write.c:26) ==45136== by 0x575953D: write (write.c:24) ==45136== by 0x35761F: ion (in /usr/bin/perf) ==45136== by 0x357778: writen (in /usr/bin/perf) ==45136== by 0x1548F7: record__write (in /usr/bin/perf) ==45136== by 0x15708A: __cmd_record.constprop.0 (in /usr/bin/perf) ==45136== by 0x15A845: cmd_record (in /usr/bin/perf) ==45136== by 0x201B7E: run_builtin (in /usr/bin/perf) ==45136== by 0x142D76: main (in /usr/bin/perf) ==45136== Address 0x6a866a8 is 0 bytes after a block of size 40 alloc'd ==45136== at 0x4849BF3: calloc (vg_replace_malloc.c:1675) ==45136== by 0x3574AB: zalloc (in /usr/bin/perf) ==45136== by 0x1570E0: __cmd_record.constprop.0 (in /usr/bin/perf) ==45136== by 0x15A845: cmd_record (in /usr/bin/perf) ==45136== by 0x201B7E: run_builtin (in /usr/bin/perf) ==45136== by 0x142D76: main (in /usr/bin/perf) ==45136== ----- Closes: https://lore.kernel.org/linux-perf-users/23879991.0LEYPuXRzz@milian-workstation/ Reported-by: Milian Wolff <[email protected]> Tested-by: Milian Wolff <[email protected]> Cc: Adrian Hunter <[email protected]> Cc: Ian Rogers <[email protected]> Cc: Jiri Olsa <[email protected]> Cc: Kan Liang <[email protected]> Cc: Namhyung Kim <[email protected]> Cc: [email protected] # 6.8+ Link: https://lore.kernel.org/lkml/Zl9ksOlHJHnKM70p@x1 Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>

We have been seeing crashes on duplicate keys in btrfs_set_item_key_safe(): BTRFS critical (device vdb): slot 4 key (450 108 8192) new key (450 108 8192) ------------[ cut here ]------------ kernel BUG at fs/btrfs/ctree.c:2620! invalid opcode: 0000 [khadas#1] PREEMPT SMP PTI CPU: 0 PID: 3139 Comm: xfs_io Kdump: loaded Not tainted 6.9.0 khadas#6 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-2.fc40 04/01/2014 RIP: 0010:btrfs_set_item_key_safe+0x11f/0x290 [btrfs] With the following stack trace: #0 btrfs_set_item_key_safe (fs/btrfs/ctree.c:2620:4) khadas#1 btrfs_drop_extents (fs/btrfs/file.c:411:4) khadas#2 log_one_extent (fs/btrfs/tree-log.c:4732:9) khadas#3 btrfs_log_changed_extents (fs/btrfs/tree-log.c:4955:9) khadas#4 btrfs_log_inode (fs/btrfs/tree-log.c:6626:9) khadas#5 btrfs_log_inode_parent (fs/btrfs/tree-log.c:7070:8) khadas#6 btrfs_log_dentry_safe (fs/btrfs/tree-log.c:7171:8) khadas#7 btrfs_sync_file (fs/btrfs/file.c:1933:8) khadas#8 vfs_fsync_range (fs/sync.c:188:9) khadas#9 vfs_fsync (fs/sync.c:202:9) khadas#10 do_fsync (fs/sync.c:212:9) khadas#11 __do_sys_fdatasync (fs/sync.c:225:9) khadas#12 __se_sys_fdatasync (fs/sync.c:223:1) khadas#13 __x64_sys_fdatasync (fs/sync.c:223:1) khadas#14 do_syscall_x64 (arch/x86/entry/common.c:52:14) khadas#15 do_syscall_64 (arch/x86/entry/common.c:83:7) khadas#16 entry_SYSCALL_64+0xaf/0x14c (arch/x86/entry/entry_64.S:121) So we're logging a changed extent from fsync, which is splitting an extent in the log tree. But this split part already exists in the tree, triggering the BUG(). This is the state of the log tree at the time of the crash, dumped with drgn (https://github.com/osandov/drgn/blob/main/contrib/btrfs_tree.py) to get more details than btrfs_print_leaf() gives us: >>> print_extent_buffer(prog.crashed_thread().stack_trace()[0]["eb"]) leaf 33439744 level 0 items 72 generation 9 owner 18446744073709551610 leaf 33439744 flags 0x100000000000000 fs uuid e5bd3946-400c-4223-8923-190ef1f18677 chunk uuid d58cb17e-6d02-494a-829a-18b7d8a399da item 0 key (450 INODE_ITEM 0) itemoff 16123 itemsize 160 generation 7 transid 9 size 8192 nbytes 8473563889606862198 block group 0 mode 100600 links 1 uid 0 gid 0 rdev 0 sequence 204 flags 0x10(PREALLOC) atime 1716417703.220000000 (2024-05-22 15:41:43) ctime 1716417704.983333333 (2024-05-22 15:41:44) mtime 1716417704.983333333 (2024-05-22 15:41:44) otime 17592186044416.000000000 (559444-03-08 01:40:16) item 1 key (450 INODE_REF 256) itemoff 16110 itemsize 13 index 195 namelen 3 name: 193 item 2 key (450 XATTR_ITEM 1640047104) itemoff 16073 itemsize 37 location key (0 UNKNOWN.0 0) type XATTR transid 7 data_len 1 name_len 6 name: user.a data a item 3 key (450 EXTENT_DATA 0) itemoff 16020 itemsize 53 generation 9 type 1 (regular) extent data disk byte 303144960 nr 12288 extent data offset 0 nr 4096 ram 12288 extent compression 0 (none) item 4 key (450 EXTENT_DATA 4096) itemoff 15967 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 4096 nr 8192 item 5 key (450 EXTENT_DATA 8192) itemoff 15914 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 8192 nr 4096 ... So the real problem happened earlier: notice that items 4 (4k-12k) and 5 (8k-12k) overlap. Both are prealloc extents. Item 4 straddles i_size and item 5 starts at i_size. Here is the state of the filesystem tree at the time of the crash: >>> root = prog.crashed_thread().stack_trace()[2]["inode"].root >>> ret, nodes, slots = btrfs_search_slot(root, BtrfsKey(450, 0, 0)) >>> print_extent_buffer(nodes[0]) leaf 30425088 level 0 items 184 generation 9 owner 5 leaf 30425088 flags 0x100000000000000 fs uuid e5bd3946-400c-4223-8923-190ef1f18677 chunk uuid d58cb17e-6d02-494a-829a-18b7d8a399da ... item 179 key (450 INODE_ITEM 0) itemoff 4907 itemsize 160 generation 7 transid 7 size 4096 nbytes 12288 block group 0 mode 100600 links 1 uid 0 gid 0 rdev 0 sequence 6 flags 0x10(PREALLOC) atime 1716417703.220000000 (2024-05-22 15:41:43) ctime 1716417703.220000000 (2024-05-22 15:41:43) mtime 1716417703.220000000 (2024-05-22 15:41:43) otime 1716417703.220000000 (2024-05-22 15:41:43) item 180 key (450 INODE_REF 256) itemoff 4894 itemsize 13 index 195 namelen 3 name: 193 item 181 key (450 XATTR_ITEM 1640047104) itemoff 4857 itemsize 37 location key (0 UNKNOWN.0 0) type XATTR transid 7 data_len 1 name_len 6 name: user.a data a item 182 key (450 EXTENT_DATA 0) itemoff 4804 itemsize 53 generation 9 type 1 (regular) extent data disk byte 303144960 nr 12288 extent data offset 0 nr 8192 ram 12288 extent compression 0 (none) item 183 key (450 EXTENT_DATA 8192) itemoff 4751 itemsize 53 generation 9 type 2 (prealloc) prealloc data disk byte 303144960 nr 12288 prealloc data offset 8192 nr 4096 Item 5 in the log tree corresponds to item 183 in the filesystem tree, but nothing matches item 4. Furthermore, item 183 is the last item in the leaf. btrfs_log_prealloc_extents() is responsible for logging prealloc extents beyond i_size. It first truncates any previously logged prealloc extents that start beyond i_size. Then, it walks the filesystem tree and copies the prealloc extent items to the log tree. If it hits the end of a leaf, then it calls btrfs_next_leaf(), which unlocks the tree and does another search. However, while the filesystem tree is unlocked, an ordered extent completion may modify the tree. In particular, it may insert an extent item that overlaps with an extent item that was already copied to the log tree. This may manifest in several ways depending on the exact scenario, including an EEXIST error that is silently translated to a full sync, overlapping items in the log tree, or this crash. This particular crash is triggered by the following sequence of events: - Initially, the file has i_size=4k, a regular extent from 0-4k, and a prealloc extent beyond i_size from 4k-12k. The prealloc extent item is the last item in its B-tree leaf. - The file is fsync'd, which copies its inode item and both extent items to the log tree. - An xattr is set on the file, which sets the BTRFS_INODE_COPY_EVERYTHING flag. - The range 4k-8k in the file is written using direct I/O. i_size is extended to 8k, but the ordered extent is still in flight. - The file is fsync'd. Since BTRFS_INODE_COPY_EVERYTHING is set, this calls copy_inode_items_to_log(), which calls btrfs_log_prealloc_extents(). - btrfs_log_prealloc_extents() finds the 4k-12k prealloc extent in the filesystem tree. Since it starts before i_size, it skips it. Since it is the last item in its B-tree leaf, it calls btrfs_next_leaf(). - btrfs_next_leaf() unlocks the path. - The ordered extent completion runs, which converts the 4k-8k part of the prealloc extent to written and inserts the remaining prealloc part from 8k-12k. - btrfs_next_leaf() does a search and finds the new prealloc extent 8k-12k. - btrfs_log_prealloc_extents() copies the 8k-12k prealloc extent into the log tree. Note that it overlaps with the 4k-12k prealloc extent that was copied to the log tree by the first fsync. - fsync calls btrfs_log_changed_extents(), which tries to log the 4k-8k extent that was written. - This tries to drop the range 4k-8k in the log tree, which requires adjusting the start of the 4k-12k prealloc extent in the log tree to 8k. - btrfs_set_item_key_safe() sees that there is already an extent starting at 8k in the log tree and calls BUG(). Fix this by detecting when we're about to insert an overlapping file extent item in the log tree and truncating the part that would overlap. CC: [email protected] # 6.1+ Reviewed-by: Filipe Manana <[email protected]> Signed-off-by: Omar Sandoval <[email protected]> Signed-off-by: David Sterba <[email protected]>

…play During inode logging (and log replay too), we are holding a transaction handle and we often need to call btrfs_iget(), which will read an inode from its subvolume btree if it's not loaded in memory and that results in allocating an inode with GFP_KERNEL semantics at the btrfs_alloc_inode() callback - and this may recurse into the filesystem in case we are under memory pressure and attempt to commit the current transaction, resulting in a deadlock since the logging (or log replay) task is holding a transaction handle open. Syzbot reported this with the following stack traces: WARNING: possible circular locking dependency detected 6.10.0-rc2-syzkaller-00361-g061d1af7b030 #0 Not tainted ------------------------------------------------------ syz-executor.1/9919 is trying to acquire lock: ffffffff8dd3aac0 (fs_reclaim){+.+.}-{0:0}, at: might_alloc include/linux/sched/mm.h:334 [inline] ffffffff8dd3aac0 (fs_reclaim){+.+.}-{0:0}, at: slab_pre_alloc_hook mm/slub.c:3891 [inline] ffffffff8dd3aac0 (fs_reclaim){+.+.}-{0:0}, at: slab_alloc_node mm/slub.c:3981 [inline] ffffffff8dd3aac0 (fs_reclaim){+.+.}-{0:0}, at: kmem_cache_alloc_lru_noprof+0x58/0x2f0 mm/slub.c:4020 but task is already holding lock: ffff88804b569358 (&ei->log_mutex){+.+.}-{3:3}, at: btrfs_log_inode+0x39c/0x4660 fs/btrfs/tree-log.c:6481 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> khadas#3 (&ei->log_mutex){+.+.}-{3:3}: __mutex_lock_common kernel/locking/mutex.c:608 [inline] __mutex_lock+0x175/0x9c0 kernel/locking/mutex.c:752 btrfs_log_inode+0x39c/0x4660 fs/btrfs/tree-log.c:6481 btrfs_log_inode_parent+0x8cb/0x2a90 fs/btrfs/tree-log.c:7079 btrfs_log_dentry_safe+0x59/0x80 fs/btrfs/tree-log.c:7180 btrfs_sync_file+0x9c1/0xe10 fs/btrfs/file.c:1959 vfs_fsync_range+0x141/0x230 fs/sync.c:188 generic_write_sync include/linux/fs.h:2794 [inline] btrfs_do_write_iter+0x584/0x10c0 fs/btrfs/file.c:1705 new_sync_write fs/read_write.c:497 [inline] vfs_write+0x6b6/0x1140 fs/read_write.c:590 ksys_write+0x12f/0x260 fs/read_write.c:643 do_syscall_32_irqs_on arch/x86/entry/common.c:165 [inline] __do_fast_syscall_32+0x73/0x120 arch/x86/entry/common.c:386 do_fast_syscall_32+0x32/0x80 arch/x86/entry/common.c:411 entry_SYSENTER_compat_after_hwframe+0x84/0x8e -> khadas#2 (btrfs_trans_num_extwriters){++++}-{0:0}: join_transaction+0x164/0xf40 fs/btrfs/transaction.c:315 start_transaction+0x427/0x1a70 fs/btrfs/transaction.c:700 btrfs_commit_super+0xa1/0x110 fs/btrfs/disk-io.c:4170 close_ctree+0xcb0/0xf90 fs/btrfs/disk-io.c:4324 generic_shutdown_super+0x159/0x3d0 fs/super.c:642 kill_anon_super+0x3a/0x60 fs/super.c:1226 btrfs_kill_super+0x3b/0x50 fs/btrfs/super.c:2096 deactivate_locked_super+0xbe/0x1a0 fs/super.c:473 deactivate_super+0xde/0x100 fs/super.c:506 cleanup_mnt+0x222/0x450 fs/namespace.c:1267 task_work_run+0x14e/0x250 kernel/task_work.c:180 resume_user_mode_work include/linux/resume_user_mode.h:50 [inline] exit_to_user_mode_loop kernel/entry/common.c:114 [inline] exit_to_user_mode_prepare include/linux/entry-common.h:328 [inline] __syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline] syscall_exit_to_user_mode+0x278/0x2a0 kernel/entry/common.c:218 __do_fast_syscall_32+0x80/0x120 arch/x86/entry/common.c:389 do_fast_syscall_32+0x32/0x80 arch/x86/entry/common.c:411 entry_SYSENTER_compat_after_hwframe+0x84/0x8e -> khadas#1 (btrfs_trans_num_writers){++++}-{0:0}: __lock_release kernel/locking/lockdep.c:5468 [inline] lock_release+0x33e/0x6c0 kernel/locking/lockdep.c:5774 percpu_up_read include/linux/percpu-rwsem.h:99 [inline] __sb_end_write include/linux/fs.h:1650 [inline] sb_end_intwrite include/linux/fs.h:1767 [inline] __btrfs_end_transaction+0x5ca/0x920 fs/btrfs/transaction.c:1071 btrfs_commit_inode_delayed_inode+0x228/0x330 fs/btrfs/delayed-inode.c:1301 btrfs_evict_inode+0x960/0xe80 fs/btrfs/inode.c:5291 evict+0x2ed/0x6c0 fs/inode.c:667 iput_final fs/inode.c:1741 [inline] iput.part.0+0x5a8/0x7f0 fs/inode.c:1767 iput+0x5c/0x80 fs/inode.c:1757 dentry_unlink_inode+0x295/0x480 fs/dcache.c:400 __dentry_kill+0x1d0/0x600 fs/dcache.c:603 dput.part.0+0x4b1/0x9b0 fs/dcache.c:845 dput+0x1f/0x30 fs/dcache.c:835 ovl_stack_put+0x60/0x90 fs/overlayfs/util.c:132 ovl_destroy_inode+0xc6/0x190 fs/overlayfs/super.c:182 destroy_inode+0xc4/0x1b0 fs/inode.c:311 iput_final fs/inode.c:1741 [inline] iput.part.0+0x5a8/0x7f0 fs/inode.c:1767 iput+0x5c/0x80 fs/inode.c:1757 dentry_unlink_inode+0x295/0x480 fs/dcache.c:400 __dentry_kill+0x1d0/0x600 fs/dcache.c:603 shrink_kill fs/dcache.c:1048 [inline] shrink_dentry_list+0x140/0x5d0 fs/dcache.c:1075 prune_dcache_sb+0xeb/0x150 fs/dcache.c:1156 super_cache_scan+0x32a/0x550 fs/super.c:221 do_shrink_slab+0x44f/0x11c0 mm/shrinker.c:435 shrink_slab_memcg mm/shrinker.c:548 [inline] shrink_slab+0xa87/0x1310 mm/shrinker.c:626 shrink_one+0x493/0x7c0 mm/vmscan.c:4790 shrink_many mm/vmscan.c:4851 [inline] lru_gen_shrink_node+0x89f/0x1750 mm/vmscan.c:4951 shrink_node mm/vmscan.c:5910 [inline] kswapd_shrink_node mm/vmscan.c:6720 [inline] balance_pgdat+0x1105/0x1970 mm/vmscan.c:6911 kswapd+0x5ea/0xbf0 mm/vmscan.c:7180 kthread+0x2c1/0x3a0 kernel/kthread.c:389 ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 -> #0 (fs_reclaim){+.+.}-{0:0}: check_prev_add kernel/locking/lockdep.c:3134 [inline] check_prevs_add kernel/locking/lockdep.c:3253 [inline] validate_chain kernel/locking/lockdep.c:3869 [inline] __lock_acquire+0x2478/0x3b30 kernel/locking/lockdep.c:5137 lock_acquire kernel/locking/lockdep.c:5754 [inline] lock_acquire+0x1b1/0x560 kernel/locking/lockdep.c:5719 __fs_reclaim_acquire mm/page_alloc.c:3801 [inline] fs_reclaim_acquire+0x102/0x160 mm/page_alloc.c:3815 might_alloc include/linux/sched/mm.h:334 [inline] slab_pre_alloc_hook mm/slub.c:3891 [inline] slab_alloc_node mm/slub.c:3981 [inline] kmem_cache_alloc_lru_noprof+0x58/0x2f0 mm/slub.c:4020 btrfs_alloc_inode+0x118/0xb20 fs/btrfs/inode.c:8411 alloc_inode+0x5d/0x230 fs/inode.c:261 iget5_locked fs/inode.c:1235 [inline] iget5_locked+0x1c9/0x2c0 fs/inode.c:1228 btrfs_iget_locked fs/btrfs/inode.c:5590 [inline] btrfs_iget_path fs/btrfs/inode.c:5607 [inline] btrfs_iget+0xfb/0x230 fs/btrfs/inode.c:5636 add_conflicting_inode fs/btrfs/tree-log.c:5657 [inline] copy_inode_items_to_log+0x1039/0x1e30 fs/btrfs/tree-log.c:5928 btrfs_log_inode+0xa48/0x4660 fs/btrfs/tree-log.c:6592 log_new_delayed_dentries fs/btrfs/tree-log.c:6363 [inline] btrfs_log_inode+0x27dd/0x4660 fs/btrfs/tree-log.c:6718 btrfs_log_all_parents fs/btrfs/tree-log.c:6833 [inline] btrfs_log_inode_parent+0x22ba/0x2a90 fs/btrfs/tree-log.c:7141 btrfs_log_dentry_safe+0x59/0x80 fs/btrfs/tree-log.c:7180 btrfs_sync_file+0x9c1/0xe10 fs/btrfs/file.c:1959 vfs_fsync_range+0x141/0x230 fs/sync.c:188 generic_write_sync include/linux/fs.h:2794 [inline] btrfs_do_write_iter+0x584/0x10c0 fs/btrfs/file.c:1705 do_iter_readv_writev+0x504/0x780 fs/read_write.c:741 vfs_writev+0x36f/0xde0 fs/read_write.c:971 do_pwritev+0x1b2/0x260 fs/read_write.c:1072 __do_compat_sys_pwritev2 fs/read_write.c:1218 [inline] __se_compat_sys_pwritev2 fs/read_write.c:1210 [inline] __ia32_compat_sys_pwritev2+0x121/0x1b0 fs/read_write.c:1210 do_syscall_32_irqs_on arch/x86/entry/common.c:165 [inline] __do_fast_syscall_32+0x73/0x120 arch/x86/entry/common.c:386 do_fast_syscall_32+0x32/0x80 arch/x86/entry/common.c:411 entry_SYSENTER_compat_after_hwframe+0x84/0x8e other info that might help us debug this: Chain exists of: fs_reclaim --> btrfs_trans_num_extwriters --> &ei->log_mutex Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&ei->log_mutex); lock(btrfs_trans_num_extwriters); lock(&ei->log_mutex); lock(fs_reclaim); *** DEADLOCK *** 7 locks held by syz-executor.1/9919: #0: ffff88802be20420 (sb_writers#23){.+.+}-{0:0}, at: do_pwritev+0x1b2/0x260 fs/read_write.c:1072 khadas#1: ffff888065c0f8f0 (&sb->s_type->i_mutex_key#33){++++}-{3:3}, at: inode_lock include/linux/fs.h:791 [inline] khadas#1: ffff888065c0f8f0 (&sb->s_type->i_mutex_key#33){++++}-{3:3}, at: btrfs_inode_lock+0xc8/0x110 fs/btrfs/inode.c:385 khadas#2: ffff888065c0f778 (&ei->i_mmap_lock){++++}-{3:3}, at: btrfs_inode_lock+0xee/0x110 fs/btrfs/inode.c:388 khadas#3: ffff88802be20610 (sb_internal#4){.+.+}-{0:0}, at: btrfs_sync_file+0x95b/0xe10 fs/btrfs/file.c:1952 khadas#4: ffff8880546323f0 (btrfs_trans_num_writers){++++}-{0:0}, at: join_transaction+0x430/0xf40 fs/btrfs/transaction.c:290 khadas#5: ffff888054632418 (btrfs_trans_num_extwriters){++++}-{0:0}, at: join_transaction+0x430/0xf40 fs/btrfs/transaction.c:290 khadas#6: ffff88804b569358 (&ei->log_mutex){+.+.}-{3:3}, at: btrfs_log_inode+0x39c/0x4660 fs/btrfs/tree-log.c:6481 stack backtrace: CPU: 2 PID: 9919 Comm: syz-executor.1 Not tainted 6.10.0-rc2-syzkaller-00361-g061d1af7b030 #0 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.2-debian-1.16.2-1 04/01/2014 Call Trace: <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0x116/0x1f0 lib/dump_stack.c:114 check_noncircular+0x31a/0x400 kernel/locking/lockdep.c:2187 check_prev_add kernel/locking/lockdep.c:3134 [inline] check_prevs_add kernel/locking/lockdep.c:3253 [inline] validate_chain kernel/locking/lockdep.c:3869 [inline] __lock_acquire+0x2478/0x3b30 kernel/locking/lockdep.c:5137 lock_acquire kernel/locking/lockdep.c:5754 [inline] lock_acquire+0x1b1/0x560 kernel/locking/lockdep.c:5719 __fs_reclaim_acquire mm/page_alloc.c:3801 [inline] fs_reclaim_acquire+0x102/0x160 mm/page_alloc.c:3815 might_alloc include/linux/sched/mm.h:334 [inline] slab_pre_alloc_hook mm/slub.c:3891 [inline] slab_alloc_node mm/slub.c:3981 [inline] kmem_cache_alloc_lru_noprof+0x58/0x2f0 mm/slub.c:4020 btrfs_alloc_inode+0x118/0xb20 fs/btrfs/inode.c:8411 alloc_inode+0x5d/0x230 fs/inode.c:261 iget5_locked fs/inode.c:1235 [inline] iget5_locked+0x1c9/0x2c0 fs/inode.c:1228 btrfs_iget_locked fs/btrfs/inode.c:5590 [inline] btrfs_iget_path fs/btrfs/inode.c:5607 [inline] btrfs_iget+0xfb/0x230 fs/btrfs/inode.c:5636 add_conflicting_inode fs/btrfs/tree-log.c:5657 [inline] copy_inode_items_to_log+0x1039/0x1e30 fs/btrfs/tree-log.c:5928 btrfs_log_inode+0xa48/0x4660 fs/btrfs/tree-log.c:6592 log_new_delayed_dentries fs/btrfs/tree-log.c:6363 [inline] btrfs_log_inode+0x27dd/0x4660 fs/btrfs/tree-log.c:6718 btrfs_log_all_parents fs/btrfs/tree-log.c:6833 [inline] btrfs_log_inode_parent+0x22ba/0x2a90 fs/btrfs/tree-log.c:7141 btrfs_log_dentry_safe+0x59/0x80 fs/btrfs/tree-log.c:7180 btrfs_sync_file+0x9c1/0xe10 fs/btrfs/file.c:1959 vfs_fsync_range+0x141/0x230 fs/sync.c:188 generic_write_sync include/linux/fs.h:2794 [inline] btrfs_do_write_iter+0x584/0x10c0 fs/btrfs/file.c:1705 do_iter_readv_writev+0x504/0x780 fs/read_write.c:741 vfs_writev+0x36f/0xde0 fs/read_write.c:971 do_pwritev+0x1b2/0x260 fs/read_write.c:1072 __do_compat_sys_pwritev2 fs/read_write.c:1218 [inline] __se_compat_sys_pwritev2 fs/read_write.c:1210 [inline] __ia32_compat_sys_pwritev2+0x121/0x1b0 fs/read_write.c:1210 do_syscall_32_irqs_on arch/x86/entry/common.c:165 [inline] __do_fast_syscall_32+0x73/0x120 arch/x86/entry/common.c:386 do_fast_syscall_32+0x32/0x80 arch/x86/entry/common.c:411 entry_SYSENTER_compat_after_hwframe+0x84/0x8e RIP: 0023:0xf7334579 Code: b8 01 10 06 03 (...) RSP: 002b:00000000f5f265ac EFLAGS: 00000292 ORIG_RAX: 000000000000017b RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 00000000200002c0 RDX: 0000000000000001 RSI: 0000000000000000 RDI: 0000000000000000 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000292 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 Fix this by ensuring we are under a NOFS scope whenever we call btrfs_iget() during inode logging and log replay. Reported-by: [email protected] Link: https://lore.kernel.org/linux-btrfs/[email protected]/ Fixes: 712e36c ("btrfs: use GFP_KERNEL in btrfs_alloc_inode") Reviewed-by: Johannes Thumshirn <[email protected]> Reviewed-by: Josef Bacik <[email protected]> Reviewed-by: Qu Wenruo <[email protected]> Signed-off-by: Filipe Manana <[email protected]> Reviewed-by: David Sterba <[email protected]> Signed-off-by: David Sterba <[email protected]>

The code in ocfs2_dio_end_io_write() estimates number of necessary transaction credits using ocfs2_calc_extend_credits(). This however does not take into account that the IO could be arbitrarily large and can contain arbitrary number of extents. Extent tree manipulations do often extend the current transaction but not in all of the cases. For example if we have only single block extents in the tree, ocfs2_mark_extent_written() will end up calling ocfs2_replace_extent_rec() all the time and we will never extend the current transaction and eventually exhaust all the transaction credits if the IO contains many single block extents. Once that happens a WARN_ON(jbd2_handle_buffer_credits(handle) <= 0) is triggered in jbd2_journal_dirty_metadata() and subsequently OCFS2 aborts in response to this error. This was actually triggered by one of our customers on a heavily fragmented OCFS2 filesystem. To fix the issue make sure the transaction always has enough credits for one extent insert before each call of ocfs2_mark_extent_written(). Heming Zhao said: ------ PANIC: "Kernel panic - not syncing: OCFS2: (device dm-1): panic forced after error" PID: xxx TASK: xxxx CPU: 5 COMMAND: "SubmitThread-CA" #0 machine_kexec at ffffffff8c069932 khadas#1 __crash_kexec at ffffffff8c1338fa khadas#2 panic at ffffffff8c1d69b9 khadas#3 ocfs2_handle_error at ffffffffc0c86c0c [ocfs2] khadas#4 __ocfs2_abort at ffffffffc0c88387 [ocfs2] khadas#5 ocfs2_journal_dirty at ffffffffc0c51e98 [ocfs2] khadas#6 ocfs2_split_extent at ffffffffc0c27ea3 [ocfs2] khadas#7 ocfs2_change_extent_flag at ffffffffc0c28053 [ocfs2] khadas#8 ocfs2_mark_extent_written at ffffffffc0c28347 [ocfs2] khadas#9 ocfs2_dio_end_io_write at ffffffffc0c2bef9 [ocfs2] khadas#10 ocfs2_dio_end_io at ffffffffc0c2c0f5 [ocfs2] khadas#11 dio_complete at ffffffff8c2b9fa7 khadas#12 do_blockdev_direct_IO at ffffffff8c2bc09f khadas#13 ocfs2_direct_IO at ffffffffc0c2b653 [ocfs2] khadas#14 generic_file_direct_write at ffffffff8c1dcf14 khadas#15 __generic_file_write_iter at ffffffff8c1dd07b khadas#16 ocfs2_file_write_iter at ffffffffc0c49f1f [ocfs2] khadas#17 aio_write at ffffffff8c2cc72e khadas#18 kmem_cache_alloc at ffffffff8c248dde khadas#19 do_io_submit at ffffffff8c2ccada khadas#20 do_syscall_64 at ffffffff8c004984 khadas#21 entry_SYSCALL_64_after_hwframe at ffffffff8c8000ba Link: https://lkml.kernel.org/r/[email protected] Link: https://lkml.kernel.org/r/[email protected] Fixes: c15471f ("ocfs2: fix sparse file & data ordering issue in direct io") Signed-off-by: Jan Kara <[email protected]> Reviewed-by: Joseph Qi <[email protected]> Reviewed-by: Heming Zhao <[email protected]> Cc: Mark Fasheh <[email protected]> Cc: Joel Becker <[email protected]> Cc: Junxiao Bi <[email protected]> Cc: Changwei Ge <[email protected]> Cc: Gang He <[email protected]> Cc: Jun Piao <[email protected]> Cc: <[email protected]> Signed-off-by: Andrew Morton <[email protected]>

A kernel warning was reported when pinning folio in CMA memory when launching SEV virtual machine. The splat looks like: [ 464.325306] WARNING: CPU: 13 PID: 6734 at mm/gup.c:1313 __get_user_pages+0x423/0x520 [ 464.325464] CPU: 13 PID: 6734 Comm: qemu-kvm Kdump: loaded Not tainted 6.6.33+ khadas#6 [ 464.325477] RIP: 0010:__get_user_pages+0x423/0x520 [ 464.325515] Call Trace: [ 464.325520] <TASK> [ 464.325523] ? __get_user_pages+0x423/0x520 [ 464.325528] ? __warn+0x81/0x130 [ 464.325536] ? __get_user_pages+0x423/0x520 [ 464.325541] ? report_bug+0x171/0x1a0 [ 464.325549] ? handle_bug+0x3c/0x70 [ 464.325554] ? exc_invalid_op+0x17/0x70 [ 464.325558] ? asm_exc_invalid_op+0x1a/0x20 [ 464.325567] ? __get_user_pages+0x423/0x520 [ 464.325575] __gup_longterm_locked+0x212/0x7a0 [ 464.325583] internal_get_user_pages_fast+0xfb/0x190 [ 464.325590] pin_user_pages_fast+0x47/0x60 [ 464.325598] sev_pin_memory+0xca/0x170 [kvm_amd] [ 464.325616] sev_mem_enc_register_region+0x81/0x130 [kvm_amd] Per the analysis done by yangge, when starting the SEV virtual machine, it will call pin_user_pages_fast(..., FOLL_LONGTERM, ...) to pin the memory. But the page is in CMA area, so fast GUP will fail then fallback to the slow path due to the longterm pinnalbe check in try_grab_folio(). The slow path will try to pin the pages then migrate them out of CMA area. But the slow path also uses try_grab_folio() to pin the page, it will also fail due to the same check then the above warning is triggered. In addition, the try_grab_folio() is supposed to be used in fast path and it elevates folio refcount by using add ref unless zero. We are guaranteed to have at least one stable reference in slow path, so the simple atomic add could be used. The performance difference should be trivial, but the misuse may be confusing and misleading. Redefined try_grab_folio() to try_grab_folio_fast(), and try_grab_page() to try_grab_folio(), and use them in the proper paths. This solves both the abuse and the kernel warning. The proper naming makes their usecase more clear and should prevent from abusing in the future. peterx said: : The user will see the pin fails, for gpu-slow it further triggers the WARN : right below that failure (as in the original report): : : folio = try_grab_folio(page, page_increm - 1, : foll_flags); : if (WARN_ON_ONCE(!folio)) { <------------------------ here : /* : * Release the 1st page ref if the : * folio is problematic, fail hard. : */ : gup_put_folio(page_folio(page), 1, : foll_flags); : ret = -EFAULT; : goto out; : } [1] https://lore.kernel.org/linux-mm/[email protected]/ [[email protected]: fix implicit declaration of function try_grab_folio_fast] Link: https://lkml.kernel.org/r/CAHbLzkowMSso-4Nufc9hcMehQsK9PNz3OSu-+eniU-2Mm-xjhA@mail.gmail.com Link: https://lkml.kernel.org/r/[email protected] Fixes: 57edfcf ("mm/gup: accelerate thp gup even for "pages != NULL"") Signed-off-by: Yang Shi <[email protected]> Reported-by: yangge <[email protected]> Cc: Christoph Hellwig <[email protected]> Cc: David Hildenbrand <[email protected]> Cc: Peter Xu <[email protected]> Cc: <[email protected]> [6.6+] Signed-off-by: Andrew Morton <[email protected]>

…te_call_indirect commit f5d03da upstream. kprobe_emulate_call_indirect currently uses int3_emulate_call to emulate indirect calls. However, int3_emulate_call always assumes the size of the call to be 5 bytes when calculating the return address. This is incorrect for register-based indirect calls in x86, which can be either 2 or 3 bytes depending on whether REX prefix is used. At kprobe runtime, the incorrect return address causes control flow to land onto the wrong place after return -- possibly not a valid instruction boundary. This can lead to a panic like the following: [ 7.308204][ C1] BUG: unable to handle page fault for address: 000000000002b4d8 [ 7.308883][ C1] #PF: supervisor read access in kernel mode [ 7.309168][ C1] #PF: error_code(0x0000) - not-present page [ 7.309461][ C1] PGD 0 P4D 0 [ 7.309652][ C1] Oops: 0000 [khadas#1] SMP [ 7.309929][ C1] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 6.7.0-rc5-trace-for-next khadas#6 [ 7.310397][ C1] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-20220807_005459-localhost 04/01/2014 [ 7.311068][ C1] RIP: 0010:__common_interrupt+0x52/0xc0 [ 7.311349][ C1] Code: 01 00 4d 85 f6 74 39 49 81 fe 00 f0 ff ff 77 30 4c 89 f7 4d 8b 5e 68 41 ba 91 76 d8 42 45 03 53 fc 74 02 0f 0b cc ff d3 65 48 <8b> 05 30 c7 ff 7e 65 4c 89 3d 28 c7 ff 7e 5b 41 5c 41 5e 41 5f c3 [ 7.312512][ C1] RSP: 0018:ffffc900000e0fd0 EFLAGS: 00010046 [ 7.312899][ C1] RAX: 0000000000000001 RBX: 0000000000000023 RCX: 0000000000000001 [ 7.313334][ C1] RDX: 00000000000003cd RSI: 0000000000000001 RDI: ffff888100d302a4 [ 7.313702][ C1] RBP: 0000000000000001 R08: 0ef439818636191f R09: b1621ff338a3b482 [ 7.314146][ C1] R10: ffffffff81e5127b R11: ffffffff81059810 R12: 0000000000000023 [ 7.314509][ C1] R13: 0000000000000000 R14: ffff888100d30200 R15: 0000000000000000 [ 7.314951][ C1] FS: 0000000000000000(0000) GS:ffff88813bc80000(0000) knlGS:0000000000000000 [ 7.315396][ C1] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 7.315691][ C1] CR2: 000000000002b4d8 CR3: 0000000003028003 CR4: 0000000000370ef0 [ 7.316153][ C1] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 7.316508][ C1] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 7.316948][ C1] Call Trace: [ 7.317123][ C1] <IRQ> [ 7.317279][ C1] ? __die_body+0x64/0xb0 [ 7.317482][ C1] ? page_fault_oops+0x248/0x370 [ 7.317712][ C1] ? __wake_up+0x96/0xb0 [ 7.317964][ C1] ? exc_page_fault+0x62/0x130 [ 7.318211][ C1] ? asm_exc_page_fault+0x22/0x30 [ 7.318444][ C1] ? __cfi_native_send_call_func_single_ipi+0x10/0x10 [ 7.318860][ C1] ? default_idle+0xb/0x10 [ 7.319063][ C1] ? __common_interrupt+0x52/0xc0 [ 7.319330][ C1] common_interrupt+0x78/0x90 [ 7.319546][ C1] </IRQ> [ 7.319679][ C1] <TASK> [ 7.319854][ C1] asm_common_interrupt+0x22/0x40 [ 7.320082][ C1] RIP: 0010:default_idle+0xb/0x10 [ 7.320309][ C1] Code: 4c 01 c7 4c 29 c2 e9 72 ff ff ff cc cc cc cc 90 90 90 90 90 90 90 90 90 90 90 b8 0c 67 40 a5 66 90 0f 00 2d 09 b9 3b 00 fb f4 <fa> c3 0f 1f 00 90 90 90 90 90 90 90 90 90 90 90 b8 0c 67 40 a5 e9 [ 7.321449][ C1] RSP: 0018:ffffc9000009bee8 EFLAGS: 00000256 [ 7.321808][ C1] RAX: ffff88813bca8b68 RBX: 0000000000000001 RCX: 000000000001ef0c [ 7.322227][ C1] RDX: 0000000000000000 RSI: 0000000000000001 RDI: 000000000001ef0c [ 7.322656][ C1] RBP: ffffc9000009bef8 R08: 8000000000000000 R09: 00000000000008c2 [ 7.323083][ C1] R10: 0000000000000000 R11: ffffffff81058e70 R12: 0000000000000000 [ 7.323530][ C1] R13: ffff8881002b30c0 R14: 0000000000000000 R15: 0000000000000000 [ 7.323948][ C1] ? __cfi_lapic_next_deadline+0x10/0x10 [ 7.324239][ C1] default_idle_call+0x31/0x50 [ 7.324464][ C1] do_idle+0xd3/0x240 [ 7.324690][ C1] cpu_startup_entry+0x25/0x30 [ 7.324983][ C1] start_secondary+0xb4/0xc0 [ 7.325217][ C1] secondary_startup_64_no_verify+0x179/0x17b [ 7.325498][ C1] </TASK> [ 7.325641][ C1] Modules linked in: [ 7.325906][ C1] CR2: 000000000002b4d8 [ 7.326104][ C1] ---[ end trace 0000000000000000 ]--- [ 7.326354][ C1] RIP: 0010:__common_interrupt+0x52/0xc0 [ 7.326614][ C1] Code: 01 00 4d 85 f6 74 39 49 81 fe 00 f0 ff ff 77 30 4c 89 f7 4d 8b 5e 68 41 ba 91 76 d8 42 45 03 53 fc 74 02 0f 0b cc ff d3 65 48 <8b> 05 30 c7 ff 7e 65 4c 89 3d 28 c7 ff 7e 5b 41 5c 41 5e 41 5f c3 [ 7.327570][ C1] RSP: 0018:ffffc900000e0fd0 EFLAGS: 00010046 [ 7.327910][ C1] RAX: 0000000000000001 RBX: 0000000000000023 RCX: 0000000000000001 [ 7.328273][ C1] RDX: 00000000000003cd RSI: 0000000000000001 RDI: ffff888100d302a4 [ 7.328632][ C1] RBP: 0000000000000001 R08: 0ef439818636191f R09: b1621ff338a3b482 [ 7.329223][ C1] R10: ffffffff81e5127b R11: ffffffff81059810 R12: 0000000000000023 [ 7.329780][ C1] R13: 0000000000000000 R14: ffff888100d30200 R15: 0000000000000000 [ 7.330193][ C1] FS: 0000000000000000(0000) GS:ffff88813bc80000(0000) knlGS:0000000000000000 [ 7.330632][ C1] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 7.331050][ C1] CR2: 000000000002b4d8 CR3: 0000000003028003 CR4: 0000000000370ef0 [ 7.331454][ C1] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 7.331854][ C1] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 7.332236][ C1] Kernel panic - not syncing: Fatal exception in interrupt [ 7.332730][ C1] Kernel Offset: disabled [ 7.333044][ C1] ---[ end Kernel panic - not syncing: Fatal exception in interrupt ]--- The relevant assembly code is (from objdump, faulting address highlighted): ffffffff8102ed9d: 41 ff d3 call *%r11 ffffffff8102eda0: 65 48 <8b> 05 30 c7 ff mov %gs:0x7effc730(%rip),%rax The emulation incorrectly sets the return address to be ffffffff8102ed9d + 0x5 = ffffffff8102eda2, which is the 8b byte in the middle of the next mov. This in turn causes incorrect subsequent instruction decoding and eventually triggers the page fault above. Instead of invoking int3_emulate_call, perform push and jmp emulation directly in kprobe_emulate_call_indirect. At this point we can obtain the instruction size from p->ainsn.size so that we can calculate the correct return address. Link: https://lore.kernel.org/all/[email protected]/ Fixes: 6256e66 ("x86/kprobes: Use int3 instead of debug trap for single-step") Cc: [email protected] Signed-off-by: Jinghao Jia <[email protected]> Signed-off-by: Masami Hiramatsu (Google) <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

commit b684c09 upstream. ppc_save_regs() skips one stack frame while saving the CPU register states. Instead of saving current R1, it pulls the previous stack frame pointer. When vmcores caused by direct panic call (such as `echo c > /proc/sysrq-trigger`), are debugged with gdb, gdb fails to show the backtrace correctly. On further analysis, it was found that it was because of mismatch between r1 and NIP. GDB uses NIP to get current function symbol and uses corresponding debug info of that function to unwind previous frames, but due to the mismatching r1 and NIP, the unwinding does not work, and it fails to unwind to the 2nd frame and hence does not show the backtrace. GDB backtrace with vmcore of kernel without this patch: --------- (gdb) bt #0 0xc0000000002a53e8 in crash_setup_regs (oldregs=<optimized out>, newregs=0xc000000004f8f8d8) at ./arch/powerpc/include/asm/kexec.h:69 khadas#1 __crash_kexec (regs=<optimized out>) at kernel/kexec_core.c:974 khadas#2 0x0000000000000063 in ?? () khadas#3 0xc000000003579320 in ?? () --------- Further analysis revealed that the mismatch occurred because "ppc_save_regs" was saving the previous stack's SP instead of the current r1. This patch fixes this by storing current r1 in the saved pt_regs. GDB backtrace with vmcore of patched kernel: -------- (gdb) bt #0 0xc0000000002a53e8 in crash_setup_regs (oldregs=0x0, newregs=0xc00000000670b8d8) at ./arch/powerpc/include/asm/kexec.h:69 khadas#1 __crash_kexec (regs=regs@entry=0x0) at kernel/kexec_core.c:974 khadas#2 0xc000000000168918 in panic (fmt=fmt@entry=0xc000000001654a60 "sysrq triggered crash\n") at kernel/panic.c:358 khadas#3 0xc000000000b735f8 in sysrq_handle_crash (key=<optimized out>) at drivers/tty/sysrq.c:155 khadas#4 0xc000000000b742cc in __handle_sysrq (key=key@entry=99, check_mask=check_mask@entry=false) at drivers/tty/sysrq.c:602 khadas#5 0xc000000000b7506c in write_sysrq_trigger (file=<optimized out>, buf=<optimized out>, count=2, ppos=<optimized out>) at drivers/tty/sysrq.c:1163 khadas#6 0xc00000000069a7bc in pde_write (ppos=<optimized out>, count=<optimized out>, buf=<optimized out>, file=<optimized out>, pde=0xc00000000362cb40) at fs/proc/inode.c:340 khadas#7 proc_reg_write (file=<optimized out>, buf=<optimized out>, count=<optimized out>, ppos=<optimized out>) at fs/proc/inode.c:352 khadas#8 0xc0000000005b3bbc in vfs_write (file=file@entry=0xc000000006aa6b00, buf=buf@entry=0x61f498b4f60 <error: Cannot access memory at address 0x61f498b4f60>, count=count@entry=2, pos=pos@entry=0xc00000000670bda0) at fs/read_write.c:582 khadas#9 0xc0000000005b4264 in ksys_write (fd=<optimized out>, buf=0x61f498b4f60 <error: Cannot access memory at address 0x61f498b4f60>, count=2) at fs/read_write.c:637 khadas#10 0xc00000000002ea2c in system_call_exception (regs=0xc00000000670be80, r0=<optimized out>) at arch/powerpc/kernel/syscall.c:171 khadas#11 0xc00000000000c270 in system_call_vectored_common () at arch/powerpc/kernel/interrupt_64.S:192 -------- Nick adds: So this now saves regs as though it was an interrupt taken in the caller, at the instruction after the call to ppc_save_regs, whereas previously the NIP was there, but R1 came from the caller's caller and that mismatch is what causes gdb's dwarf unwinder to go haywire. Signed-off-by: Aditya Gupta <[email protected]> Fixes: d16a58f ("powerpc: Improve ppc_save_regs()") Reivewed-by: Nicholas Piggin <[email protected]> Signed-off-by: Michael Ellerman <[email protected]> Link: https://msgid.link/[email protected] Cc: [email protected] Signed-off-by: Aditya Gupta <[email protected]> Signed-off-by: Greg Kroah-Hartman <[email protected]>

Dmitry reported a lockdep splat [1] (false positive) that we can fix by releasing the spinlock before calling icmp_send() from ip_expire() This is a false positive because sending an ICMP message can not possibly re-enter the IP frag engine. [1] [ INFO: possible circular locking dependency detected ] 4.10.0+ #29 Not tainted ------------------------------------------------------- modprobe/12392 is trying to acquire lock: (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] spin_lock include/linux/spinlock.h:299 [inline] (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] __netif_tx_lock include/linux/netdevice.h:3486 [inline] (_xmit_ETHER#2){+.-...}, at: [<ffffffff837a8182>] sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180 but task is already holding lock: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] spin_lock include/linux/spinlock.h:299 [inline] (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] ip_expire+0x51/0x6c0 net/ipv4/ip_fragment.c:201 which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #1 (&(&q->lock)->rlock){+.-...}: validate_chain kernel/locking/lockdep.c:2267 [inline] __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:299 [inline] ip_defrag+0x3a2/0x4130 net/ipv4/ip_fragment.c:669 ip_check_defrag+0x4e3/0x8b0 net/ipv4/ip_fragment.c:713 packet_rcv_fanout+0x282/0x800 net/packet/af_packet.c:1459 deliver_skb net/core/dev.c:1834 [inline] dev_queue_xmit_nit+0x294/0xa90 net/core/dev.c:1890 xmit_one net/core/dev.c:2903 [inline] dev_hard_start_xmit+0x16b/0xab0 net/core/dev.c:2923 sch_direct_xmit+0x31f/0x6d0 net/sched/sch_generic.c:182 __dev_xmit_skb net/core/dev.c:3092 [inline] __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 neigh_resolve_output+0x6b9/0xb10 net/core/neighbour.c:1308 neigh_output include/net/neighbour.h:478 [inline] ip_finish_output2+0x8b8/0x15a0 net/ipv4/ip_output.c:228 ip_do_fragment+0x1d93/0x2720 net/ipv4/ip_output.c:672 ip_fragment.constprop.54+0x145/0x200 net/ipv4/ip_output.c:545 ip_finish_output+0x82d/0xe10 net/ipv4/ip_output.c:314 NF_HOOK_COND include/linux/netfilter.h:246 [inline] ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404 dst_output include/net/dst.h:486 [inline] ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512 raw_sendmsg+0x26de/0x3a00 net/ipv4/raw.c:655 inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:761 sock_sendmsg_nosec net/socket.c:633 [inline] sock_sendmsg+0xca/0x110 net/socket.c:643 ___sys_sendmsg+0x4a3/0x9f0 net/socket.c:1985 __sys_sendmmsg+0x25c/0x750 net/socket.c:2075 SYSC_sendmmsg net/socket.c:2106 [inline] SyS_sendmmsg+0x35/0x60 net/socket.c:2101 do_syscall_64+0x2e8/0x930 arch/x86/entry/common.c:281 return_from_SYSCALL_64+0x0/0x7a -> #0 (_xmit_ETHER#2){+.-...}: check_prev_add kernel/locking/lockdep.c:1830 [inline] check_prevs_add+0xa8f/0x19f0 kernel/locking/lockdep.c:1940 validate_chain kernel/locking/lockdep.c:2267 [inline] __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:299 [inline] __netif_tx_lock include/linux/netdevice.h:3486 [inline] sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180 __dev_xmit_skb net/core/dev.c:3092 [inline] __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 neigh_hh_output include/net/neighbour.h:468 [inline] neigh_output include/net/neighbour.h:476 [inline] ip_finish_output2+0xf6c/0x15a0 net/ipv4/ip_output.c:228 ip_finish_output+0xa29/0xe10 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:246 [inline] ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404 dst_output include/net/dst.h:486 [inline] ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512 icmp_push_reply+0x372/0x4d0 net/ipv4/icmp.c:394 icmp_send+0x156c/0x1c80 net/ipv4/icmp.c:754 ip_expire+0x40e/0x6c0 net/ipv4/ip_fragment.c:239 call_timer_fn+0x241/0x820 kernel/time/timer.c:1268 expire_timers kernel/time/timer.c:1307 [inline] __run_timers+0x960/0xcf0 kernel/time/timer.c:1601 run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614 __do_softirq+0x31f/0xbe7 kernel/softirq.c:284 invoke_softirq kernel/softirq.c:364 [inline] irq_exit+0x1cc/0x200 kernel/softirq.c:405 exiting_irq arch/x86/include/asm/apic.h:657 [inline] smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:962 apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:707 __read_once_size include/linux/compiler.h:254 [inline] atomic_read arch/x86/include/asm/atomic.h:26 [inline] rcu_dynticks_curr_cpu_in_eqs kernel/rcu/tree.c:350 [inline] __rcu_is_watching kernel/rcu/tree.c:1133 [inline] rcu_is_watching+0x83/0x110 kernel/rcu/tree.c:1147 rcu_read_lock_held+0x87/0xc0 kernel/rcu/update.c:293 radix_tree_deref_slot include/linux/radix-tree.h:238 [inline] filemap_map_pages+0x6d4/0x1570 mm/filemap.c:2335 do_fault_around mm/memory.c:3231 [inline] do_read_fault mm/memory.c:3265 [inline] do_fault+0xbd5/0x2080 mm/memory.c:3370 handle_pte_fault mm/memory.c:3600 [inline] __handle_mm_fault+0x1062/0x2cb0 mm/memory.c:3714 handle_mm_fault+0x1e2/0x480 mm/memory.c:3751 __do_page_fault+0x4f6/0xb60 arch/x86/mm/fault.c:1397 do_page_fault+0x54/0x70 arch/x86/mm/fault.c:1460 page_fault+0x28/0x30 arch/x86/entry/entry_64.S:1011 other info that might help us debug this: Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&(&q->lock)->rlock); lock(_xmit_ETHER#2); lock(&(&q->lock)->rlock); lock(_xmit_ETHER#2); *** DEADLOCK *** 10 locks held by modprobe/12392: #0: (&mm->mmap_sem){++++++}, at: [<ffffffff81329758>] __do_page_fault+0x2b8/0xb60 arch/x86/mm/fault.c:1336 #1: (rcu_read_lock){......}, at: [<ffffffff8188cab6>] filemap_map_pages+0x1e6/0x1570 mm/filemap.c:2324 #2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>] spin_lock include/linux/spinlock.h:299 [inline] #2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>] pte_alloc_one_map mm/memory.c:2944 [inline] #2: (&(ptlock_ptr(page))->rlock#2){+.+...}, at: [<ffffffff81984a78>] alloc_set_pte+0x13b8/0x1b90 mm/memory.c:3072 #3: (((&q->timer))){+.-...}, at: [<ffffffff81627e72>] lockdep_copy_map include/linux/lockdep.h:175 [inline] #3: (((&q->timer))){+.-...}, at: [<ffffffff81627e72>] call_timer_fn+0x1c2/0x820 kernel/time/timer.c:1258 #4: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] spin_lock include/linux/spinlock.h:299 [inline] #4: (&(&q->lock)->rlock){+.-...}, at: [<ffffffff8389a4d1>] ip_expire+0x51/0x6c0 net/ipv4/ip_fragment.c:201 #5: (rcu_read_lock){......}, at: [<ffffffff8389a633>] ip_expire+0x1b3/0x6c0 net/ipv4/ip_fragment.c:216 #6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] spin_trylock include/linux/spinlock.h:309 [inline] #6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] icmp_xmit_lock net/ipv4/icmp.c:219 [inline] #6: (slock-AF_INET){+.-...}, at: [<ffffffff839b3313>] icmp_send+0x803/0x1c80 net/ipv4/icmp.c:681 #7: (rcu_read_lock_bh){......}, at: [<ffffffff838ab9a1>] ip_finish_output2+0x2c1/0x15a0 net/ipv4/ip_output.c:198 #8: (rcu_read_lock_bh){......}, at: [<ffffffff836d1dee>] __dev_queue_xmit+0x23e/0x1e60 net/core/dev.c:3324 #9: (dev->qdisc_running_key ?: &qdisc_running_key){+.....}, at: [<ffffffff836d3a27>] dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 stack backtrace: CPU: 0 PID: 12392 Comm: modprobe Not tainted 4.10.0+ #29 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:16 [inline] dump_stack+0x2ee/0x3ef lib/dump_stack.c:52 print_circular_bug+0x307/0x3b0 kernel/locking/lockdep.c:1204 check_prev_add kernel/locking/lockdep.c:1830 [inline] check_prevs_add+0xa8f/0x19f0 kernel/locking/lockdep.c:1940 validate_chain kernel/locking/lockdep.c:2267 [inline] __lock_acquire+0x2149/0x3430 kernel/locking/lockdep.c:3340 lock_acquire+0x2a1/0x630 kernel/locking/lockdep.c:3755 __raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline] _raw_spin_lock+0x33/0x50 kernel/locking/spinlock.c:151 spin_lock include/linux/spinlock.h:299 [inline] __netif_tx_lock include/linux/netdevice.h:3486 [inline] sch_direct_xmit+0x282/0x6d0 net/sched/sch_generic.c:180 __dev_xmit_skb net/core/dev.c:3092 [inline] __dev_queue_xmit+0x13e5/0x1e60 net/core/dev.c:3358 dev_queue_xmit+0x17/0x20 net/core/dev.c:3423 neigh_hh_output include/net/neighbour.h:468 [inline] neigh_output include/net/neighbour.h:476 [inline] ip_finish_output2+0xf6c/0x15a0 net/ipv4/ip_output.c:228 ip_finish_output+0xa29/0xe10 net/ipv4/ip_output.c:316 NF_HOOK_COND include/linux/netfilter.h:246 [inline] ip_output+0x1f0/0x7a0 net/ipv4/ip_output.c:404 dst_output include/net/dst.h:486 [inline] ip_local_out+0x95/0x170 net/ipv4/ip_output.c:124 ip_send_skb+0x3c/0xc0 net/ipv4/ip_output.c:1492 ip_push_pending_frames+0x64/0x80 net/ipv4/ip_output.c:1512 icmp_push_reply+0x372/0x4d0 net/ipv4/icmp.c:394 icmp_send+0x156c/0x1c80 net/ipv4/icmp.c:754 ip_expire+0x40e/0x6c0 net/ipv4/ip_fragment.c:239 call_timer_fn+0x241/0x820 kernel/time/timer.c:1268 expire_timers kernel/time/timer.c:1307 [inline] __run_timers+0x960/0xcf0 kernel/time/timer.c:1601 run_timer_softirq+0x21/0x80 kernel/time/timer.c:1614 __do_softirq+0x31f/0xbe7 kernel/softirq.c:284 invoke_softirq kernel/softirq.c:364 [inline] irq_exit+0x1cc/0x200 kernel/softirq.c:405 exiting_irq arch/x86/include/asm/apic.h:657 [inline] smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:962 apic_timer_interrupt+0x93/0xa0 arch/x86/entry/entry_64.S:707 RIP: 0010:__read_once_size include/linux/compiler.h:254 [inline] RIP: 0010:atomic_read arch/x86/include/asm/atomic.h:26 [inline] RIP: 0010:rcu_dynticks_curr_cpu_in_eqs kernel/rcu/tree.c:350 [inline] RIP: 0010:__rcu_is_watching kernel/rcu/tree.c:1133 [inline] RIP: 0010:rcu_is_watching+0x83/0x110 kernel/rcu/tree.c:1147 RSP: 0000:ffff8801c391f120 EFLAGS: 00000a03 ORIG_RAX: ffffffffffffff10 RAX: dffffc0000000000 RBX: ffff8801c391f148 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 000055edd4374000 RDI: ffff8801dbe1ae0c RBP: ffff8801c391f1a0 R08: 0000000000000002 R09: 0000000000000000 R10: dffffc0000000000 R11: 0000000000000002 R12: 1ffff10038723e25 R13: ffff8801dbe1ae00 R14: ffff8801c391f680 R15: dffffc0000000000 </IRQ> rcu_read_lock_held+0x87/0xc0 kernel/rcu/update.c:293 radix_tree_deref_slot include/linux/radix-tree.h:238 [inline] filemap_map_pages+0x6d4/0x1570 mm/filemap.c:2335 do_fault_around mm/memory.c:3231 [inline] do_read_fault mm/memory.c:3265 [inline] do_fault+0xbd5/0x2080 mm/memory.c:3370 handle_pte_fault mm/memory.c:3600 [inline] __handle_mm_fault+0x1062/0x2cb0 mm/memory.c:3714 handle_mm_fault+0x1e2/0x480 mm/memory.c:3751 __do_page_fault+0x4f6/0xb60 arch/x86/mm/fault.c:1397 do_page_fault+0x54/0x70 arch/x86/mm/fault.c:1460 page_fault+0x28/0x30 arch/x86/entry/entry_64.S:1011 RIP: 0033:0x7f83172f2786 RSP: 002b:00007fffe859ae80 EFLAGS: 00010293 RAX: 000055edd4373040 RBX: 00007f83175111c8 RCX: 000055edd4373238 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00007f8317510970 RBP: 00007fffe859afd0 R08: 0000000000000009 R09: 0000000000000000 R10: 0000000000000064 R11: 0000000000000000 R12: 000055edd4373040 R13: 0000000000000000 R14: 00007fffe859afe8 R15: 0000000000000000 Signed-off-by: Eric Dumazet <[email protected]> Reported-by: Dmitry Vyukov <[email protected]> Signed-off-by: David S. Miller <[email protected]>

Recently I got a Caldigit TS3 Thunderbolt 3 dock, and noticed that upon hotplugging my kernel would immediately crash due to igb: [ 680.825801] kernel BUG at drivers/pci/msi.c:352! [ 680.828388] invalid opcode: 0000 [#1] SMP [ 680.829194] Modules linked in: igb(O) thunderbolt i2c_algo_bit joydev vfat fat btusb btrtl btbcm btintel bluetooth ecdh_generic hp_wmi sparse_keymap rfkill wmi_bmof iTCO_wdt intel_rapl x86_pkg_temp_thermal coretemp crc32_pclmul snd_pcm rtsx_pci_ms mei_me snd_timer memstick snd pcspkr mei soundcore i2c_i801 tpm_tis psmouse shpchp wmi tpm_tis_core tpm video hp_wireless acpi_pad rtsx_pci_sdmmc mmc_core crc32c_intel serio_raw rtsx_pci mfd_core xhci_pci xhci_hcd i2c_hid i2c_core [last unloaded: igb] [ 680.831085] CPU: 1 PID: 78 Comm: kworker/u16:1 Tainted: G O 4.15.0-rc3Lyude-Test+ #6 [ 680.831596] Hardware name: HP HP ZBook Studio G4/826B, BIOS P71 Ver. 01.03 06/09/2017 [ 680.832168] Workqueue: kacpi_hotplug acpi_hotplug_work_fn [ 680.832687] RIP: 0010:free_msi_irqs+0x180/0x1b0 [ 680.833271] RSP: 0018:ffffc9000030fbf0 EFLAGS: 00010286 [ 680.833761] RAX: ffff8803405f9c00 RBX: ffff88033e3d2e40 RCX: 000000000000002c [ 680.834278] RDX: 0000000000000000 RSI: 00000000000000ac RDI: ffff880340be2178 [ 680.834832] RBP: 0000000000000000 R08: ffff880340be1ff0 R09: ffff8803405f9c00 [ 680.835342] R10: 0000000000000000 R11: 0000000000000040 R12: ffff88033d63a298 [ 680.835822] R13: ffff88033d63a000 R14: 0000000000000060 R15: ffff880341959000 [ 680.836332] FS: 0000000000000000(0000) GS:ffff88034f440000(0000) knlGS:0000000000000000 [ 680.836817] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 680.837360] CR2: 000055e64044afdf CR3: 0000000001c09002 CR4: 00000000003606e0 [ 680.837954] Call Trace: [ 680.838853] pci_disable_msix+0xce/0xf0 [ 680.839616] igb_reset_interrupt_capability+0x5d/0x60 [igb] [ 680.840278] igb_remove+0x9d/0x110 [igb] [ 680.840764] pci_device_remove+0x36/0xb0 [ 680.841279] device_release_driver_internal+0x157/0x220 [ 680.841739] pci_stop_bus_device+0x7d/0xa0 [ 680.842255] pci_stop_bus_device+0x2b/0xa0 [ 680.842722] pci_stop_bus_device+0x3d/0xa0 [ 680.843189] pci_stop_and_remove_bus_device+0xe/0x20 [ 680.843627] trim_stale_devices+0xf3/0x140 [ 680.844086] trim_stale_devices+0x94/0x140 [ 680.844532] trim_stale_devices+0xa6/0x140 [ 680.845031] ? get_slot_status+0x90/0xc0 [ 680.845536] acpiphp_check_bridge.part.5+0xfe/0x140 [ 680.846021] acpiphp_hotplug_notify+0x175/0x200 [ 680.846581] ? free_bridge+0x100/0x100 [ 680.847113] acpi_device_hotplug+0x8a/0x490 [ 680.847535] acpi_hotplug_work_fn+0x1a/0x30 [ 680.848076] process_one_work+0x182/0x3a0 [ 680.848543] worker_thread+0x2e/0x380 [ 680.848963] ? process_one_work+0x3a0/0x3a0 [ 680.849373] kthread+0x111/0x130 [ 680.849776] ? kthread_create_worker_on_cpu+0x50/0x50 [ 680.850188] ret_from_fork+0x1f/0x30 [ 680.850601] Code: 43 14 85 c0 0f 84 d5 fe ff ff 31 ed eb 0f 83 c5 01 39 6b 14 0f 86 c5 fe ff ff 8b 7b 10 01 ef e8 b7 e4 d2 ff 48 83 78 70 00 74 e3 <0f> 0b 49 8d b5 a0 00 00 00 e8 62 6f d3 ff e9 c7 fe ff ff 48 8b [ 680.851497] RIP: free_msi_irqs+0x180/0x1b0 RSP: ffffc9000030fbf0 As it turns out, normally the freeing of IRQs that would fix this is called inside of the scope of __igb_close(). However, since the device is already gone by the point we try to unregister the netdevice from the driver due to a hotplug we end up seeing that the netif isn't present and thus, forget to free any of the device IRQs. So: make sure that if we're in the process of dismantling the netdev, we always allow __igb_close() to be called so that IRQs may be freed normally. Additionally, only allow igb_close() to be called from __igb_close() if it hasn't already been called for the given adapter. Signed-off-by: Lyude Paul <[email protected]> Fixes: 9474933 ("igb: close/suspend race in netif_device_detach") Cc: Todd Fujinaka <[email protected]> Cc: Stephen Hemminger <[email protected]> Cc: [email protected] Tested-by: Aaron Brown <[email protected]> Signed-off-by: Jeff Kirsher <[email protected]>

… set We received an error report that perf-record caused 'Segmentation fault' on a newly system (e.g. on the new installed ubuntu). (gdb) backtrace #0 __read_once_size (size=4, res=<synthetic pointer>, p=0x14) at /root/0-jinyao/acme/tools/include/linux/compiler.h:139 #1 atomic_read (v=0x14) at /root/0-jinyao/acme/tools/include/asm/../../arch/x86/include/asm/atomic.h:28 #2 refcount_read (r=0x14) at /root/0-jinyao/acme/tools/include/linux/refcount.h:65 #3 perf_mmap__read_init (map=map@entry=0x0) at mmap.c:177 #4 0x0000561ce5c0de39 in perf_evlist__poll_thread (arg=0x561ce68584d0) at util/sideband_evlist.c:62 #5 0x00007fad78491609 in start_thread (arg=<optimized out>) at pthread_create.c:477 #6 0x00007fad7823c103 in clone () at ../sysdeps/unix/sysv/linux/x86_64/clone.S:95 The root cause is, evlist__add_bpf_sb_event() just returns 0 if HAVE_LIBBPF_SUPPORT is not defined (inline function path). So it will not create a valid evsel for side-band event. But perf-record still creates BPF side band thread to process the side-band event, then the error happpens. We can reproduce this issue by removing the libelf-dev. e.g. 1. apt-get remove libelf-dev 2. perf record -a -- sleep 1 root@test:~# ./perf record -a -- sleep 1 perf: Segmentation fault Obtained 6 stack frames. ./perf(+0x28eee8) [0x5562d6ef6ee8] /lib/x86_64-linux-gnu/libc.so.6(+0x46210) [0x7fbfdc65f210] ./perf(+0x342e74) [0x5562d6faae74] ./perf(+0x257e39) [0x5562d6ebfe39] /lib/x86_64-linux-gnu/libpthread.so.0(+0x9609) [0x7fbfdc990609] /lib/x86_64-linux-gnu/libc.so.6(clone+0x43) [0x7fbfdc73b103] Segmentation fault (core dumped) To fix this issue, 1. We either install the missing libraries to let HAVE_LIBBPF_SUPPORT be defined. e.g. apt-get install libelf-dev and install other related libraries. 2. Use this patch to skip the side-band event setup if HAVE_LIBBPF_SUPPORT is not set. Committer notes: The side band thread is not used just with BPF, it is also used with --switch-output-event, so narrow the ifdef to the BPF specific part. Fixes: 23cbb41 ("perf record: Move side band evlist setup to separate routine") Signed-off-by: Jin Yao <[email protected]> Acked-by: Jiri Olsa <[email protected]> Cc: Alexander Shishkin <[email protected]> Cc: Andi Kleen <[email protected]> Cc: Jin Yao <[email protected]> Cc: Kan Liang <[email protected]> Cc: Peter Zijlstra <[email protected]> Link: http://lore.kernel.org/lkml/[email protected] Signed-off-by: Arnaldo Carvalho de Melo <[email protected]>

test_bpf tail call tests end up as: test_bpf: #0 Tail call leaf jited:1 85 PASS test_bpf: #1 Tail call 2 jited:1 111 PASS test_bpf: #2 Tail call 3 jited:1 145 PASS test_bpf: #3 Tail call 4 jited:1 170 PASS test_bpf: #4 Tail call load/store leaf jited:1 190 PASS test_bpf: #5 Tail call load/store jited:1 BUG: Unable to handle kernel data access on write at 0xf1b4e000 Faulting instruction address: 0xbe86b710 Oops: Kernel access of bad area, sig: 11 [#1] BE PAGE_SIZE=4K MMU=Hash PowerMac Modules linked in: test_bpf(+) CPU: 0 PID: 97 Comm: insmod Not tainted 6.1.0-rc4+ #195 Hardware name: PowerMac3,1 750CL 0x87210 PowerMac NIP: be86b710 LR: be857e88 CTR: be86b704 REGS: f1b4df20 TRAP: 0300 Not tainted (6.1.0-rc4+) MSR: 00009032 <EE,ME,IR,DR,RI> CR: 28008242 XER: 00000000 DAR: f1b4e000 DSISR: 42000000 GPR00: 00000001 f1b4dfe0 c11d2280 00000000 00000000 00000000 00000002 00000000 GPR08: f1b4e000 be86b704 f1b4e000 00000000 00000000 100d816a f2440000 fe73baa8 GPR16: f2458000 00000000 c1941ae4 f1fe2248 00000045 c0de0000 f2458030 00000000 GPR24: 000003e8 0000000f f2458000 f1b4dc90 3e584b46 00000000 f24466a0 c1941a00 NIP [be86b710] 0xbe86b710 LR [be857e88] __run_one+0xec/0x264 [test_bpf] Call Trace: [f1b4dfe0] [00000002] 0x2 (unreliable) Instruction dump: XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX ---[ end trace 0000000000000000 ]--- This is a tentative to write above the stack. The problem is encoutered with tests added by commit 38608ee ("bpf, tests: Add load store test case for tail call") This happens because tail call is done to a BPF prog with a different stack_depth. At the time being, the stack is kept as is when the caller tail calls its callee. But at exit, the callee restores the stack based on its own properties. Therefore here, at each run, r1 is erroneously increased by 32 - 16 = 16 bytes. This was done that way in order to pass the tail call count from caller to callee through the stack. As powerpc32 doesn't have a red zone in the stack, it was necessary the maintain the stack as is for the tail call. But it was not anticipated that the BPF frame size could be different. Let's take a new approach. Use register r4 to carry the tail call count during the tail call, and save it into the stack at function entry if required. This means the input parameter must be in r3, which is more correct as it is a 32 bits parameter, then tail call better match with normal BPF function entry, the down side being that we move that input parameter back and forth between r3 and r4. That can be optimised later. Doing that also has the advantage of maximising the common parts between tail calls and a normal function exit. With the fix, tail call tests are now successfull: test_bpf: #0 Tail call leaf jited:1 53 PASS test_bpf: #1 Tail call 2 jited:1 115 PASS test_bpf: #2 Tail call 3 jited:1 154 PASS test_bpf: #3 Tail call 4 jited:1 165 PASS test_bpf: #4 Tail call load/store leaf jited:1 101 PASS test_bpf: #5 Tail call load/store jited:1 141 PASS test_bpf: #6 Tail call error path, max count reached jited:1 994 PASS test_bpf: #7 Tail call count preserved across function calls jited:1 140975 PASS test_bpf: #8 Tail call error path, NULL target jited:1 110 PASS test_bpf: #9 Tail call error path, index out of range jited:1 69 PASS test_bpf: test_tail_calls: Summary: 10 PASSED, 0 FAILED, [10/10 JIT'ed] Suggested-by: Naveen N. Rao <[email protected]> Fixes: 51c66ad ("powerpc/bpf: Implement extended BPF on PPC32") Cc: [email protected] Signed-off-by: Christophe Leroy <[email protected]> Tested-by: Naveen N. Rao <[email protected] Signed-off-by: Michael Ellerman <[email protected]> Link: https://lore.kernel.org/r/757acccb7fbfc78efa42dcf3c974b46678198905.1669278887.git.christophe.leroy@csgroup.eu

gouwa closed this Feb 3, 2018

terry2droid reopened this Feb 3, 2018

numbqq pushed a commit that referenced this pull request Oct 26, 2020

Merge pull request #6 from khadas/khadas-edge-4.4.y

1cc73d3

Khadas edge 4.4.y

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

eeprom: at24: Simplify WP management and make it optional #6

eeprom: at24: Simplify WP management and make it optional #6

bthebaudeau commented Nov 13, 2017

eeprom: at24: Simplify WP management and make it optional #6

Are you sure you want to change the base?

eeprom: at24: Simplify WP management and make it optional #6

Conversation

bthebaudeau commented Nov 13, 2017