Skip to content

Node RED

Jump to bottom
Graham Garner edited this page Dec 9, 2019 · 11 revisions

References

Build warning

The Node-RED build will complain about several issues. This is completely normal behaviour.

SQLite

Thanks to @fragolinux the SQLite node will install now. WARNING it will output many error and will look as if it has gotten stuck. Just give it time and it will continue.

GPIO

To communicate to your Pi's GPIO you need to use the node-red-node-pi-gpiod node. It allowes you to connect to multiple Pis from the same nodered service.

You need to make sure that pigpdiod is running. The recommended method is listed here You run the following command sudo nano /etc/rc.local and add the line /usr/bin/pigpiod above exit 0 and reboot the Pi. There is an option to secure the service see the writeup for further instuctions.

Fot the Rpi Image you will also need to update to the most recent version

sudo apt-get update
sudo apt-get install pigpio python-pigpio python3-pigpio

Drop the gpio node and use your Pi's IP. Example: 192.168.1.123 (127.0.0.1 won't work because this is the local address of every computer'.)

Securing Node-RED

To secure Node-RED you need a password hash. There is a terminal script ./services/nodered/terminal.sh execute it to get into the terminal. Copy the helper text node -e ..... PASSWORD, paste it and change your password to get a hash.

Open the file ./volumes/nodered/data/settings.js and follow the writeup on https://nodered.org/docs/user-guide/runtime/securing-node-red for further instructions

Sharing files between Node-RED and the host

Containers run in a sandboxed environment they can't see the host (the Pi itself) file system. This presents a problem if you want to read a file directly to the host from inside the container. Fortunately there is a method, the containers have been set up with volume mapping. The volume maps a specific directory or file from the host file system into the container. Therefore if you write to that directory both the host and the container can see the files.

Consider the following:

The docker-compose.yml file shows the following for Node-RED

    volumes:
      - ./volumes/nodered/data:/data

If inside Node-RED you were to write to the /data folder then the host would see it in ~/IOTstack/volumes/nodered/data (the ./volumes above implies relative to the docker-compose.yml file)

image

The flow writes the file /data/test.txt and it is visible in the host as ~/IOTstack/volumes/nodered/data/test.txt

Remember, files and directories in the volume are persistent between restarts. If you save your data elsewhere it will be destroyed should you restart. Creating a subdirectory in volume i.e. /data/storage/ would be advised

Using Bluetooth

In order to allow Node-RED to access the Pi's Bluetooth module the docker-comose.yml file needs to be modified to allow it access. network_mode: "host" needs to be added (make sure the indentation is correct, us spaces not tabs):

  nodered:
    container_name: nodered
    build: ./services/nodered/.
    restart: unless-stopped
    user: "0"
    network_mode: "host"

By activating host mode the Node-RED container can no longer access containers by name http://influxdb:8086 will no longer work. Node-RED thinks it now is the host and therefore access to the following services will look as follows:

  • influxdb http://127.0.0.1:8086
  • GPIO 127.0.0.1 port 8888
  • MQTT 127.0.0.1

Unused node in Protainer

Portainer will report that the nodered image is unsed, this is normal due to the method used build the image. This is normal behavior. It is not advised to remove it as it is used as the base for the iotstack_nodered image, you will need to redownload it should you rebuild the nodered image.

UnusedImage

Running the exec node against the host Pi

Due to the isolation between containers and the host the exec node will run against the container.

There is a solution to work around this. You can use ssh to execute a script on the pi. It requires a little setup but is possible.

For this example I'll be running a simple script called test.sh I create a file called test.sh in my IOTstack directory with nano

The contents are as follows:

#!/bin/bash
echo "hello"
exit 0

The exit 0 will stop the exec node from reporting an issue.

Its a good idea to add the shebang at the top. make it executable with chmod +x test.sh

This nodered running open the nodered terminal with ./services/nodered/terminal.sh or docker exec -it nodered /bin/bash or use portainer

create the ssh folder in the data directory (the /data directory is persistently mapped volume)

mkdir -p /data/ssh

create key, this will require naming the output file

ssh-keygen -f /data/ssh/nodered put in any additional config you want key type strength copy the key to the Pi. When asked for a password leave it blank

copy the ssh-key to your pi

ssh-copy-id -i /data/ssh/nodered [email protected] replace with your static IP address. You will have to reply yes to the prompt. You may also see an error referring to regular expressions however you can ignore it.

now to execute a script on the pi run ssh -i /data/ssh/nodered [email protected] /home/pi/IOTstack/test.sh

type exit to leave the terminal

(you could also restart your pi with ssh -i /data/ssh/nodered [email protected] sudo reboot)

in node red in your exec node you can run the command ssh -i /data/ssh/nodered [email protected] /home/pi/IOTstack/test.sh other the script or command of your choice

image

Clone this wiki locally