SPI serial bus access with Node.js on Linux boards like the Raspberry Pi or BeagleBone. All methods have asynchronous and synchronous forms.
spi-device supports Node.js versions 10, 12, 14, 15 and 16.
npm install spi-device
Determine the temperature using a TMP36 analog temperature sensor wired to channel 5 on an MCP3008 SPI A/D converter.
const spi = require('spi-device');
// The MCP3008 is on bus 0 and it's device 0
const mcp3008 = spi.open(0, 0, err => {
// An SPI message is an array of one or more read+write transfers
const message = [{
sendBuffer: Buffer.from([0x01, 0xd0, 0x00]), // Sent to read channel 5
receiveBuffer: Buffer.alloc(3), // Raw data read from channel 5
byteLength: 3,
speedHz: 20000 // Use a low bus speed to get a good reading from the TMP36
}];
if (err) throw err;
mcp3008.transfer(message, (err, message) => {
if (err) throw err;
// Convert raw value from sensor to celcius and log to console
const rawValue = ((message[0].receiveBuffer[1] & 0x03) << 8) +
message[0].receiveBuffer[2];
const voltage = rawValue * 3.3 / 1023;
const celcius = (voltage - 0.5) * 100;
console.log(celcius);
});
});spi-device enables low-level access to SPI devices. Often, high-level access is required. When this is the case, high-level packages can be built using spi-device. An example of such a package is mcp-spi-adc which provides a high-level API for accessing an MCP3008 SPI A/D converter and will generally be more useful than the low-level demonstration code shown above.
All methods have asynchronous and synchronous forms.
The asynchronous form always take a completion callback as its last argument. The arguments passed to the completion callback depend on the method, but the first argument is always reserved for an exception. If the operation was completed successfully, then the first argument will be null or undefined.
When using the synchronous form any exceptions are immediately thrown. You can use try/catch to handle exceptions or allow them to bubble up.
- device.transfer(message, cb)
- device.transferSync(message)
- device.getOptions(cb)
- device.getOptionsSync()
- device.setOptions(options, cb)
- device.setOptionsSync(options)
- device.close(cb)
- device.closeSync()
- busNumber - the number of the SPI bus to open, 0 for
/dev/spidev0.n, 1 for/dev/spidev1.n, ... - deviceNumber - the number of the SPI device to open, 0 for
/dev/spidevn.0, 1 for/dev/spidevn.1, ... - options - an optional object specifying device configuration options
- cb - completion callback
Asynchronous open. Returns a new SpiDevice object. The completion callback gets one argument (err). The SpiDevice object returned should not be used before the completion callback is called.
- busNumber - the number of the SPI bus to open, 0 for
/dev/spidev0.n, 1 for/dev/spidev1.n, ... - deviceNumber - the number of the SPI device to open, 0 for
/dev/spidevn.0, 1 for/dev/spidevn.1, ... - options - an optional object specifying device configuration options
Synchronous open. Returns a new SpiDevice object.
- message - an array of one or more read+write transfers
- cb - completion callback
Asynchronous message transfer. An SPI message is an array of one or more read+write transfers. The completion callback gets two arguments (err, message). Returns this.
- message - an array of one or more read+write transfers
Synchronous message transfer. An SPI message is an array of one or more read+write transfers. Returns this.
- cb - completion callback
Asynchronously read device configuration options. The completion callback gets two arguments (err, options) where options is an object describing the device configuration options. Returns this.
Synchronously read device configuration options. Returns an object describing the device configuration options.
- options - an object specifying device configuration options
- cb - completion callback
Asynchronously write device configuration options. The completion callback gets one argument (err). Returns this.
- options - an object specifying device configuration options
Synchronously write device configuration options. Returns this.
- cb - completion callback
Asynchronous close. Frees system resources used by this instance. The completion callback gets one argument (err). Returns null.
Synchronous close. Frees system resources used by this instance. Returns null.
SPI mode number 0.
SPI mode number 1.
SPI mode number 2.
SPI mode number 3.
An SPI message is an array of one or more read+write transfers. A transfer is an object with the properties listed below. Most of the properties are optional. Note that although both sendBuffer and receiveBuffer are optional, at least one one of them must be specified.
- byteLength - number, 32-bit, the number of bytes to transfer
- sendBuffer - optional Buffer, transmit data
- receiveBuffer - optional Buffer, receive data
- speedHz - optional number, 32-bit, override of the device's clock frequency in Hertz
- microSecondDelay - optional number, 16-bit, delay after the last bit transfer before optionally deselecting the device before the next transfer, default 0
- bitsPerWord - optional number, 8-bit, override of the device's wordsize
- chipSelectChange - optional boolean, true to deselect device before starting the next transfer, default false
Device configuration options can be optionally specified when a device is
opened with the open or openSync methods. They can also be specified at a
later point with the setOptions or setOptionsSync methods. When calling
these methods, only the options that need to be set need to be specified in the
options object passed to those methods. All options are optional and the
appropriate defaults will be used for options that are not specified.
The options supported varies from system to system and will depend on the device drivers used on those systems.
Configurations options can be read with the getOptions and getOptionsSync
methods.
IMPORTANT The semantics of chipSelectHigh have changed with Linux kernel 5. To the best of my knowledge, the chipSelectHigh option no longer serves any purpose when used from user space with Linux kernel 5 and should not be used. With Linux kernel 5, the chip select is assumed to be active low. With Linux kernel 5, if an SPI device has has active high chip select, it's chip select must be controlled manually with a GPIO using a module such as onoff. The chipSelectHigh option has been crossed out below but it's still available for usage on older kernels.
- mode - number, 2-bit, MODE0, MODE1, MODE2, or MODE3, default MODE0
chipSelectHigh - boolean, true for active high chip select, default false- lsbFirst - boolean, true for least significant bit first transfer, default false
- threeWire - boolean, true for shared MISO/MOSI signals, default false
- loopback - boolean, true for loopback mode, default false
- noChipSelect - boolean, true for 1 device per bus, no chip select, default false
- ready - boolean, true if device pulls low to pause, default false
- bitsPerWord - number, 8-bit, device word size, default 8
- maxSpeedHz - number, 32-bit, device clock frequency in Hertz, default system specific