⛙ Merge w/Marlin

classicrocker883 · Oct 25, 2024 · d2fa313 · d2fa313
2 parents 3ead95d + d2bda12
commit d2fa313
Show file tree

Hide file tree

Showing 142 changed files with 1,904 additions and 715 deletions.
diff --git a/.zed/settings.json b/.zed/settings.json
@@ -5,5 +5,12 @@
  * see the documentation: https://zed.dev/docs/configuring-zed#settings-files
  */
 {
-  "enable_language_servers": false
+  "languages": {
+    "C": {
+      "enable_language_server": false
+    },
+    "C++": {
+      "enable_language_server": false
+    }
+  }
 }
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
@@ -67,7 +67,7 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "Miguel A. Risco-Castillo (MRiscoC)" // Who made the changes.
+#define STRING_CONFIG_H_AUTHOR "Miguel A. Risco-Castillo (MRiscoC)" // Original author or contributor.
 #define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
 
 // @section machine
@@ -811,6 +811,40 @@
   //#define BED_LIMIT_SWITCHING   // Keep the bed temperature within BED_HYSTERESIS of the target
 #endif
 
+/**
+ * Peltier Bed - Heating and Cooling
+ *
+ * A Peltier device transfers heat from one side to the other in proportion to the amount of
+ * current flowing through the device and the direction of current flow. So the same device
+ * can both heat and cool.
+ *
+ * When "cooling" in addition to rejecting the heat transferred from the hot side to the cold
+ * side, the dissipated power (voltage * current) must also be rejected. Be sure to set up a
+ * fan that can be powered in sync with the Peltier unit.
+ *
+ * This feature is only set up to run in bang-bang mode because Peltiers don't handle PWM
+ * well without filter circuitry.
+ *
+ * Since existing 3D printers are made to handle relatively high current for the heated bed,
+ * we can use the heated bed power pins to control the Peltier power using the same G-codes
+ * as the heated bed (M140, M190, etc.).
+ *
+ * A second GPIO pin is required to control current direction.
+ * Two configurations are possible: Relay and H-Bridge
+ *
+ * (At this time only relay is supported. H-bridge requires 4 MOS switches configured in H-Bridge.)
+ *
+ * Power is handled by the bang-bang control loop: 0 or 255.
+ * Cooling applications are more common than heating, so the pin states are commonly:
+ *   LOW  = Heating = Relay Energized
+ *   HIGH = Cooling = Relay in "Normal" state
+ */
+//#define PELTIER_BED
+#if ENABLED(PELTIER_BED)
+  #define PELTIER_DIR_PIN           -1  // Relay control pin for Peltier
+  #define PELTIER_DIR_HEAT_STATE   LOW  // The relay pin state that causes the Peltier to heat
+#endif
+
 // Add 'M190 R T' for more gradual M190 R bed cooling.
 //#define BED_ANNEALING_GCODE
 
@@ -2040,9 +2074,9 @@
         //#define FIL_MOTION8_PULLUP
         //#define FIL_MOTION8_PULLDOWN
       #endif
-    #endif
-  #endif
-#endif
+    #endif // FILAMENT_MOTION_SENSOR
+  #endif // FILAMENT_RUNOUT_DISTANCE_MM
+#endif // FILAMENT_RUNOUT_SENSOR
 
 //===========================================================================
 //=============================== Bed Leveling ==============================

diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
@@ -209,7 +209,7 @@
 //
 #if DISABLED(PIDTEMPBED)
   #define BED_CHECK_INTERVAL 5000   // (ms) Interval between checks in bang-bang control
-  #if ENABLED(BED_LIMIT_SWITCHING)
+  #if ANY(BED_LIMIT_SWITCHING, PELTIER_BED)
     #define BED_HYSTERESIS 2        // (°C) Only set the relevant heater state when ABS(T-target) > BED_HYSTERESIS
   #endif
 #endif

diff --git a/Marlin/Makefile b/Marlin/Makefile
@@ -187,6 +187,17 @@ else ifeq ($(HARDWARE_MOTHERBOARD),1033)
 # RAMPS Plus 3DYMY (Power outputs: Spindle, Controller Fan)
 else ifeq ($(HARDWARE_MOTHERBOARD),1034)
 
+# RAMPS 1.6+ (Power outputs: Hotend, Fan, Bed)
+else ifeq ($(HARDWARE_MOTHERBOARD),1035)
+# RAMPS 1.6+ (Power outputs: Hotend0, Hotend1, Bed)
+else ifeq ($(HARDWARE_MOTHERBOARD),1036)
+# RAMPS 1.6+ (Power outputs: Hotend, Fan0, Fan1)
+else ifeq ($(HARDWARE_MOTHERBOARD),1037)
+# RAMPS 1.6+ (Power outputs: Hotend0, Hotend1, Fan)
+else ifeq ($(HARDWARE_MOTHERBOARD),1038)
+# RAMPS 1.6+ (Power outputs: Spindle, Controller Fan)
+else ifeq ($(HARDWARE_MOTHERBOARD),1039)
+
 #
 # RAMPS Derivatives - ATmega1280, ATmega2560
 #
@@ -221,108 +232,113 @@ else ifeq ($(HARDWARE_MOTHERBOARD),1112)
 else ifeq ($(HARDWARE_MOTHERBOARD),1113)
 # BigTreeTech or BIQU KFB2.0
 else ifeq ($(HARDWARE_MOTHERBOARD),1114)
-# zrib V2.0 (Chinese RAMPS replica)
+# Zonestar zrib V2.0 (Chinese RAMPS replica)
 else ifeq ($(HARDWARE_MOTHERBOARD),1115)
-# zrib V5.2 (Chinese RAMPS replica)
+# Zonestar zrib V5.2 (Chinese RAMPS replica)
 else ifeq ($(HARDWARE_MOTHERBOARD),1116)
-# Felix 2.0+ Electronics Board (RAMPS like)
+# Zonestar zrib V5.3 (Chinese RAMPS replica)
 else ifeq ($(HARDWARE_MOTHERBOARD),1117)
-# Invent-A-Part RigidBoard
+# Felix 2.0+ Electronics Board (RAMPS like)
 else ifeq ($(HARDWARE_MOTHERBOARD),1118)
-# Invent-A-Part RigidBoard V2
+# Invent-A-Part RigidBoard
 else ifeq ($(HARDWARE_MOTHERBOARD),1119)
-# Sainsmart 2-in-1 board
+# Invent-A-Part RigidBoard V2
 else ifeq ($(HARDWARE_MOTHERBOARD),1120)
-# Ultimaker
+# Sainsmart 2-in-1 board
 else ifeq ($(HARDWARE_MOTHERBOARD),1121)
-# Ultimaker (Older electronics. Pre 1.5.4. This is rare)
+# Ultimaker
 else ifeq ($(HARDWARE_MOTHERBOARD),1122)
+# Ultimaker (Older electronics. Pre 1.5.4. This is rare)
+else ifeq ($(HARDWARE_MOTHERBOARD),1123)
   MCU              ?= atmega1280
   PROG_MCU         ?= m1280
 # Azteeg X3
-else ifeq ($(HARDWARE_MOTHERBOARD),1123)
-# Azteeg X3 Pro
 else ifeq ($(HARDWARE_MOTHERBOARD),1124)
-# Ultimainboard 2.x (Uses TEMP_SENSOR 20)
+# Azteeg X3 Pro
 else ifeq ($(HARDWARE_MOTHERBOARD),1125)
-# Rumba
+# Ultimainboard 2.x (Uses TEMP_SENSOR 20)
 else ifeq ($(HARDWARE_MOTHERBOARD),1126)
-# Raise3D N series Rumba derivative
+# Rumba
 else ifeq ($(HARDWARE_MOTHERBOARD),1127)
-# Rapide Lite 200 (v1, low-cost RUMBA clone with drv)
+# Raise3D N series Rumba derivative
 else ifeq ($(HARDWARE_MOTHERBOARD),1128)
-# Formbot T-Rex 2 Plus
+# Rapide Lite 200 (v1, low-cost RUMBA clone with drv)
 else ifeq ($(HARDWARE_MOTHERBOARD),1129)
-# Formbot T-Rex 3
+# Formbot T-Rex 2 Plus
 else ifeq ($(HARDWARE_MOTHERBOARD),1130)
-# Formbot Raptor
+# Formbot T-Rex 3
 else ifeq ($(HARDWARE_MOTHERBOARD),1131)
-# Formbot Raptor 2
+# Formbot Raptor
 else ifeq ($(HARDWARE_MOTHERBOARD),1132)
-# bq ZUM Mega 3D
+# Formbot Raptor 2
 else ifeq ($(HARDWARE_MOTHERBOARD),1133)
-# MakeBoard Mini v2.1.2 by MicroMake
+# bq ZUM Mega 3D
 else ifeq ($(HARDWARE_MOTHERBOARD),1134)
-# TriGorilla Anycubic version 1.3-based on RAMPS EFB
+# MakeBoard Mini v2.1.2 by MicroMake
 else ifeq ($(HARDWARE_MOTHERBOARD),1135)
-#   ... Ver 1.4
+# TriGorilla Anycubic version 1.3-based on RAMPS EFB
 else ifeq ($(HARDWARE_MOTHERBOARD),1136)
-#   ... Rev 1.1 (new servo pin order)
+#   ... Ver 1.4
 else ifeq ($(HARDWARE_MOTHERBOARD),1137)
-# Creality: Ender-4, CR-8
+#   ... Rev 1.1 (new servo pin order)
 else ifeq ($(HARDWARE_MOTHERBOARD),1138)
-# Creality: CR10S, CR20, CR-X
+# Creality: Ender-4, CR-8
 else ifeq ($(HARDWARE_MOTHERBOARD),1139)
-# Dagoma F5
+# Creality: CR10S, CR20, CR-X
 else ifeq ($(HARDWARE_MOTHERBOARD),1140)
-# FYSETC F6 1.3
+# Dagoma F5
 else ifeq ($(HARDWARE_MOTHERBOARD),1141)
-# FYSETC F6 1.4
+# Dagoma D6 (as found in the Dagoma DiscoUltimate V2 TMC)
 else ifeq ($(HARDWARE_MOTHERBOARD),1142)
-# Wanhao Duplicator i3 Plus
+# FYSETC F6 1.3
 else ifeq ($(HARDWARE_MOTHERBOARD),1143)
-# VORON Design
+# FYSETC F6 1.4
 else ifeq ($(HARDWARE_MOTHERBOARD),1144)
-# Tronxy TRONXY-V3-1.0
+# Wanhao Duplicator i3 Plus
 else ifeq ($(HARDWARE_MOTHERBOARD),1145)
-# Z-Bolt X Series
+# VORON Design
 else ifeq ($(HARDWARE_MOTHERBOARD),1146)
-# TT OSCAR
+# Tronxy TRONXY-V3-1.0
 else ifeq ($(HARDWARE_MOTHERBOARD),1147)
-# Overlord/Overlord Pro
+# Z-Bolt X Series
 else ifeq ($(HARDWARE_MOTHERBOARD),1148)
-# ADIMLab Gantry v1
+# TT OSCAR
 else ifeq ($(HARDWARE_MOTHERBOARD),1149)
-# ADIMLab Gantry v2
-else ifeq ($(HARDWARE_MOTHERBOARD),1150)
 # BIQU Tango V1
-else ifeq ($(HARDWARE_MOTHERBOARD),1151)
+else ifeq ($(HARDWARE_MOTHERBOARD),1150)
 # MKS GEN L V2
-else ifeq ($(HARDWARE_MOTHERBOARD),1152)
+else ifeq ($(HARDWARE_MOTHERBOARD),1151)
 # MKS GEN L V2.1
-else ifeq ($(HARDWARE_MOTHERBOARD),1153)
+else ifeq ($(HARDWARE_MOTHERBOARD),1152)
 # Copymaster 3D
-else ifeq ($(HARDWARE_MOTHERBOARD),1154)
+else ifeq ($(HARDWARE_MOTHERBOARD),1153)
 # Ortur 4
-else ifeq ($(HARDWARE_MOTHERBOARD),1155)
+else ifeq ($(HARDWARE_MOTHERBOARD),1154)
 # Tenlog D3 Hero IDEX printer
+else ifeq ($(HARDWARE_MOTHERBOARD),1155)
+# Tenlog D3, D5, D6 IDEX Printer
 else ifeq ($(HARDWARE_MOTHERBOARD),1156)
-# Tenlog D3,5,6 Pro IDEX printers
-else ifeq ($(HARDWARE_MOTHERBOARD),1157)
 # Ramps S 1.2 by Sakul.cz (Power outputs: Hotend0, Hotend1, Fan, Bed)
-else ifeq ($(HARDWARE_MOTHERBOARD),1158)
+else ifeq ($(HARDWARE_MOTHERBOARD),1157)
 # Ramps S 1.2 by Sakul.cz (Power outputs: Hotend0, Hotend1, Hotend2, Bed)
-else ifeq ($(HARDWARE_MOTHERBOARD),1159)
+else ifeq ($(HARDWARE_MOTHERBOARD),1158)
 # Ramps S 1.2 by Sakul.cz (Power outputs: Hotend, Fan0, Fan1, Bed)
-else ifeq ($(HARDWARE_MOTHERBOARD),1160)
+else ifeq ($(HARDWARE_MOTHERBOARD),1159)
 # Longer LK1 PRO / Alfawise U20 Pro (PRO version)
-else ifeq ($(HARDWARE_MOTHERBOARD),1161)
+else ifeq ($(HARDWARE_MOTHERBOARD),1160)
 # Longer LKx PRO / Alfawise Uxx Pro (PRO version)
+else ifeq ($(HARDWARE_MOTHERBOARD),1161)
+# Pxmalion Core I3
 else ifeq ($(HARDWARE_MOTHERBOARD),1162)
-# Zonestar zrib V5.3 (Chinese RAMPS replica)
+# Panowin Cutlass (as found in the Panowin F1)
 else ifeq ($(HARDWARE_MOTHERBOARD),1163)
-# Pxmalion Core I3
+# Kodama Bardo V1.x (as found in the Kodama Trinus)
 else ifeq ($(HARDWARE_MOTHERBOARD),1164)
+# XTLW MFF V1.0
+else ifeq ($(HARDWARE_MOTHERBOARD),1165)
+# XTLW MFF V2.0
+else ifeq ($(HARDWARE_MOTHERBOARD),1166)
+
 
 #
 # RAMBo and derivatives
@@ -340,7 +356,7 @@ else ifeq ($(HARDWARE_MOTHERBOARD),1203)
 else ifeq ($(HARDWARE_MOTHERBOARD),1204)
 # abee Scoovo X9H
 else ifeq ($(HARDWARE_MOTHERBOARD),1205)
-# Rambo ThinkerV2
+# ThinkerV2
 else ifeq ($(HARDWARE_MOTHERBOARD),1206)
 
 #
@@ -383,30 +399,40 @@ else ifeq ($(HARDWARE_MOTHERBOARD),1315)
 else ifeq ($(HARDWARE_MOTHERBOARD),1316)
 # Geeetech GT2560 Rev B for A10(M/T/D)
 else ifeq ($(HARDWARE_MOTHERBOARD),1317)
-# Geeetech GT2560 Rev B for A10(M/T/D)
-else ifeq ($(HARDWARE_MOTHERBOARD),1318)
 # Geeetech GT2560 Rev B for Mecreator2
-else ifeq ($(HARDWARE_MOTHERBOARD),1319)
+else ifeq ($(HARDWARE_MOTHERBOARD),1318)
 # Geeetech GT2560 Rev B for A20(M/T/D)
+else ifeq ($(HARDWARE_MOTHERBOARD),1319)
+# Geeetech GT2560 Rev B for A10(M/T/D)
 else ifeq ($(HARDWARE_MOTHERBOARD),1320)
-# Einstart retrofit
+# Geeetech GT2560 Rev B for A20(M/T/D)
 else ifeq ($(HARDWARE_MOTHERBOARD),1321)
-# Wanhao 0ne+ i3 Mini
+# Einstart retrofit
 else ifeq ($(HARDWARE_MOTHERBOARD),1322)
-# Leapfrog Xeed 2015
+# Wanhao 0ne+ i3 Mini
 else ifeq ($(HARDWARE_MOTHERBOARD),1323)
-# PICA Shield (original version)
+# Overlord/Overlord Pro
 else ifeq ($(HARDWARE_MOTHERBOARD),1324)
-# PICA Shield (rev C or later)
+# ADIMLab Gantry v1
 else ifeq ($(HARDWARE_MOTHERBOARD),1325)
-# Intamsys 4.0 (Funmat HT)
+# ADIMLab Gantry v2
 else ifeq ($(HARDWARE_MOTHERBOARD),1326)
-# Malyan M180 Mainboard Version 2 (no display function, direct G-code only)
+# Leapfrog Xeed 2015
 else ifeq ($(HARDWARE_MOTHERBOARD),1327)
-# Geeetech GT2560 Rev B for A20(M/T/D)
+# PICA Shield (original version)
 else ifeq ($(HARDWARE_MOTHERBOARD),1328)
-# Mega controller & Protoneer CNC Shield V3.00
+# PICA Shield (rev C or later)
 else ifeq ($(HARDWARE_MOTHERBOARD),1329)
+# Intamsys 4.0 (Funmat HT)
+else ifeq ($(HARDWARE_MOTHERBOARD),1330)
+# Malyan M180 Mainboard Version 2 (no display function, direct G-code only)
+else ifeq ($(HARDWARE_MOTHERBOARD),1331)
+# Mega controller & Protoneer CNC Shield V3.00
+else ifeq ($(HARDWARE_MOTHERBOARD),1332)
+# WEEDO 62A board (TINA2, Monoprice Cadet, etc.)
+else ifeq ($(HARDWARE_MOTHERBOARD),1333)
+# Geeetech GT2560 V4.1B for A10(M/T/D)
+else ifeq ($(HARDWARE_MOTHERBOARD),1334)
 
 #
 # ATmega1281, ATmega2561
@@ -440,7 +466,7 @@ else ifeq ($(HARDWARE_MOTHERBOARD),1502)
   HARDWARE_VARIANT ?= Sanguino
   MCU              ?= atmega644p
   PROG_MCU         ?= m644p
-# Melzi V2.0
+# Melzi V2
 else ifeq ($(HARDWARE_MOTHERBOARD),1503)
   HARDWARE_VARIANT ?= Sanguino
   MCU              ?= atmega1284p
@@ -450,36 +476,41 @@ else ifeq ($(HARDWARE_MOTHERBOARD),1504)
   HARDWARE_VARIANT ?= Sanguino
   MCU              ?= atmega1284p
   PROG_MCU         ?= m1284p
-# Melzi Creality3D board (for CR-10 etc)
+# Melzi Creality3D (for CR-10 etc)
 else ifeq ($(HARDWARE_MOTHERBOARD),1505)
   HARDWARE_VARIANT ?= Sanguino
   MCU              ?= atmega1284p
   PROG_MCU         ?= m1284p
-# Melzi Malyan M150 board
+# Melzi Creality3D (for Ender-2)
 else ifeq ($(HARDWARE_MOTHERBOARD),1506)
   HARDWARE_VARIANT ?= Sanguino
   MCU              ?= atmega1284p
   PROG_MCU         ?= m1284p
-# Tronxy X5S
+# Melzi Malyan M150
 else ifeq ($(HARDWARE_MOTHERBOARD),1507)
   HARDWARE_VARIANT ?= Sanguino
   MCU              ?= atmega1284p
   PROG_MCU         ?= m1284p
-# STB V1.1
+# Tronxy X5S
 else ifeq ($(HARDWARE_MOTHERBOARD),1508)
   HARDWARE_VARIANT ?= Sanguino
   MCU              ?= atmega1284p
   PROG_MCU         ?= m1284p
-# Azteeg X1
+# STB V1.1
 else ifeq ($(HARDWARE_MOTHERBOARD),1509)
   HARDWARE_VARIANT ?= Sanguino
   MCU              ?= atmega1284p
   PROG_MCU         ?= m1284p
-# Anet 1.0 (Melzi clone)
+# Azteeg X1
 else ifeq ($(HARDWARE_MOTHERBOARD),1510)
   HARDWARE_VARIANT ?= Sanguino
   MCU              ?= atmega1284p
   PROG_MCU         ?= m1284p
+# Anet 1.0 (Melzi clone)
+else ifeq ($(HARDWARE_MOTHERBOARD),1511)
+  HARDWARE_VARIANT ?= Sanguino
+  MCU              ?= atmega1284p
+  PROG_MCU         ?= m1284p
 # ZoneStar ZMIB V2
 else ifeq ($(HARDWARE_MOTHERBOARD),1511)
   HARDWARE_VARIANT ?= Sanguino