versioning, small wording updates

README.md

@@ -1,36 +1,39 @@
 # MM-control-01
 MMU 3-axis stepper control
 
-## Below are the stable versions of MMU2 & MK3 FW required and a link to releases of latest compiled hex files.
-MMU: V#: 2.1.4	B#:  210
+## Latest stable versions & link to **RELEASES** for Precompiled HEX files
 
-MK3: V#: 5.0.3	B#: 2235
+**MMU: V#: 2.1.4	B#:  222**
 
-https://github.com/TheZeroBeast/MM-control-01/releases
+**MK3: V#: 5.0.3	B#: 2244**
+
+**https://github.com/TheZeroBeast/MM-control-01/releases**
 
 # POINTS OF NOTE
-    * You DO NOT have to reset to factory settings, all the same EEPROM data structures are used as STOCK-PRUSA-FW
-    * Bowden Length is still important as load is optimised to minimise the posibility of 
-    grinding in the event of the MK3-FSensor not triggering, rare if setup correct,
-    dust/particles still build up over time. #DEFAULT FACTORY BOWDEN LENGETH IS 350mm#
-    Adjust value BOWDEN_LENGTH, line 31 in file MOTION.CPP if custom value desired
-    * Distance to BONDTECH is set for factory R3 extruder configuration
-    Adjust value STEPS_MK3FSensor_To_Bondtech, line 32 in file MOTION.CPP if custom value desired
-    * Ensure filament sensor is enalbed via MK3 menu the first time you flash your MK3 to ensure your MMU2 gets messages when filament gets to the MK3.
+* You **DO NOT** have to reset to factory settings, all the same EEPROM data structures are used as STOCK-PRUSA-FW
+* Bowden Length is still important as load is optimised to minimise the posibility of 
+grinding in the event of the MK3-FSensor not triggering, rare if setup correct,
+dust/particles still build up over time. **DEFAULT FACTORY BOWDEN LENGETH IS 350mm**
+  * Adjust value **BOWDEN_LENGTH**, line 31 in file MOTION.CPP if custom value desired.
+    On load there is a 5s window after you here deceleration finish, adjust value so it triggers 1-2s into this window
+* Distance to BONDTECH is set for factory R3 extruder configuration
+  * Adjust value **STEPS_MK3FSensor_To_Bondtech**, line 32 in file MOTION.CPP if custom value desired
+* Ensure filament sensor is enalbed via MK3 menu the first time you flash your MK3 to ensure your MMU2 gets messages when filament gets to the MK3.
+* Load/Unload and MMU Parameters should be set in Slic3r for best performance
 
 ## When in error state Active Extruder LED will blink
-RED if Filament in FINDA
-GREEN if FINDA is clear
-    * If unload or load failed
-    * Troubleshoot issue, usually was due to being caught on an edge or ground section of filament
-        * Note: If fial on UNLOAD the LED will show on teh extruder load is going to instead of current
-        * Note: Failed LOAD where filament is found partly in Extruder requires a burst of air to clean MK3-FSensor
-    * If printer has shut down heaters, click MK3 wheel before clearing MMU2 issue with middle button
-    * *ALWAYS* ensure filament pulled clear of selector.
-    * Push middle button to rehome and continue
-        * If it doesn't work, filament is in FINDA, check again
-        
-
+### **RED   if FINDA sees Filament**
+### **GREEN if FINDA is clear**
+* If unload or load failed
+* Troubleshoot issue, usually was due to being caught on an edge or ground section of filament
+  * Note: If fail on **UNLOAD** the LED will show on the next extruder instead of current
+  * Note: Failed **LOAD** where filament is found partly in Extruder requires a burst of air to clean MK3-FSensor
+* If printer has shut down heaters, click MK3 wheel before clearing MMU2 issue with middle button
+* **ALWAYS** ensure filament pulled clear of selector.
+* Push middle button to rehome and continue
+  * If nothing happens, filament is in FINDA, check again
+  * If load fails again, give MK3-FSensor another burst of air and try again
+  
 
 ## Slic3r Advance Settging for load/unload Speed
 ![MMU2-Slic3r-LoadUnload-Speeds](/MMU2-Slic3r-LoadUnload-Speeds.png)