Created by Dave Akerman ([email protected])
This software is written for the PITS Zero with Pi Zero, PITS+ with the various A+/B+ models, and the original PITS with the Pi A/B boards.
PITS Zero and PITS+ can be purchased from board from http://ava.upuaut.net/store/.
Software support is provided for customers who have purchased a PITS, PITS Zero or PITS+ board, for use with that board only.
Follow the instructions at http://www.pi-in-the-sky.com/index.php?id=sd-card-image-from-scratch
A piezo buzzer is another helpful device for locating a landed payload. Use one that will operate from 3V and consumes less than 20mA; I use RS 617-3069 which is very loud. Connect to a 0V pin on the Pi GPIO connector, and a spare I/O pin.
Configure as follows, being careful to use a WiringPi pin number:
Piezo_Pin=4
Piezpo_Alt=1000
For the above settings, the buzzer light will come on during flight once the payload descends below 1000m.
These are very bright LED strobe lights made for RC models. You can power them from the Pi 5V and 0V lines; note that they do pull 1A for 20ms for each flash, which might cause issues depending on the power supply; if in doubt add some capacitance at the strobe.
The LED uses a PWM input to control its mode. Choose any free pin, e.g. BCM pin 18 which is only used if you have an APRS board. Configure as follows, being careful to use BCM pin numbers and not WiringPi pin numbers:
Strobe_Pin=18
Strobe_Alt=1000
For the above settings, the strobe light will come on during flight once the payload descends below 1000m.
Both V1 and V2 Strobons have been tested to work fine. PITS controls the LED by using a standard 50Hz PWM signal set with 1ms pulse for off and 2ms for on. Note that when powered up, the V2 model strobes until PITS starts; the V1 starts up as off.
You can enable any one of these supported sensor devices using these lines in pisky.txt:
Enable_BME280=Y
Enable_MS5611=Y
Enable_BMP085=Y
All of them measure pressure and temperature; the BME280 also measures humidity.
To understand the settings, first take note that PITS has a concept of "radio channels" where a channel is a particular radio transmitter not mode (RTTY or LoRa). We are using one of the LoRa devices (channels) to transmit RTTY. So our settings are associated with the particular LoRa module (in CE0 or CE1 position). Essentially we are overriding the normal LoRa functionality by telling the software to transmit RTTY as well as or instead of the LoRa packets.
These are the new settings (shown for channel 0)
- LORA_RTTY_Frequency_0=<RTTY Frequency>. Without this, RTTY will use the same frequency as LoRa. I recommend that you keep the frequencies apart so that your RTTY receiving software does not try to track the LoRa trransmissions.
- LORA_RTTY_Baud_0=<baud rate>. Choose 50 (better range) or 300 (faster, allows for SSDV, easier for dl-fldigi to lock to).
- LORA_RTTY_Shift_0=<carrier shift in Hz>. The carrier shift must be numerically greater than the baud rate. Note that the LoRa chip steps in multiples of 30.5Hz.
- LORA_RTTY_Count_0=<count>. This is how many RTTY packets are sent one after the other before transmitting any LoRa packets. 2 is recommended in case the RTTY decoder misses the start of the first packet.
- LORA_RTTY_Every_0=<count>. This is how many LoRa packets are sent one after the other before transmitting any RTTY packets. Set to zero to disable LoRa (and only send RTTY).
- LORA_RTTY_Preamble_0=<bits>. Sets the length of preamble (constant carrier) before sending RTTY data. Default is 8 and seems to be plenty.
Example:
LORA_RTTY_Frequency_0=434.350
LORA_RTTY_Baud_0=300
LORA_RTTY_Shift_0=610
LORA_RTTY_Count_0=2
LORA_RTTY_Every_0=12
LORA_RTTY_Preamble_0=8
To use a USB camera (i.e. a compact or SLR) instead of the Pi camera, you need to install gphoto2 and imagemagick:
sudo apt-get install gphoto2 imagemagick
and you need to edit /boot/pisky.txt and change the "camera" line to be:
Camera=G
(G/g are for gphoto2, U/F/u/f for fswebcam; N/n is for no camera, Y/y/1/TC/c is for CSI camera).
The camera must be able to support remote capture as well as image download, and this excludes a large number of cameras in particular all Canon compacts since 2009. There's a list of cameras at http://www.gphoto.org/doc/remote/.
The image resolution is not controlled so you should set this up in the camera. The full image files are stored on Pi SD card, so ensure that it has sufficient free capacity.
If you are transmitting images with SSDV, then these need to be resized before transmission. This is configured in pisky.txt in the usual way. The process though is different - the camera takes the full sized image, and this image is downloaded to the Pi unaltered. Before transmission the selected images are then resized using imagemagick. So, regardless of the image size settings in pisky.txt, the Pi SD card will contain the full-size images.
PITS does not set the camera exposure. Normally with the camera set to an automatic exposure mode you will get plenty of good images, but you can of course set it to any mode you wish including manual. If you wish to control this from the software rather than on the camera, then create an executable script "take_image" (there is a sample supplied as "take_image.sample"). Note that most settings are only available in the more basic modes - e.g. the aperture can only be controlled in aperture-priority or manual modes.
gphoto2 needs more work than the other camera options, and we strongly recommend some experimentation with the camera you intend to use. See http://gphoto.org/doc/manual/using-gphoto2.html.
To use a USB webcam instead of the Pi camera, you need to install fswebcam:
sudo apt-get install fswebcam
and you need to edit /boot/pisky.txt and change the "camera" line to be:
Camera=U
All images now include telemetry (longitude, latitude, altitude) in the JPEG comment field, but only if EXIV2 has been installed.
It is therefore possible to overlay downloaded images with telemetry data, as text or graphics, using (for example) ImageMagick, and EXIV2 to extract the data from the JPEG being processed. A sample script "process_image.sample" is provided; to use this, rename to be "process_image", make it executable, and edit to your requirements. Please note that the sample assumes a particular image resolution and you will need to change the pixel positions of the various items. Imagemagick is quite complex to use but there is plenty of documentation on the web plus many samples.
- Added support for new camera commands replacing raspistill. Use "R" for camera type
- Fixed bug that killed RTTY enable pin during initialisation if no cutdown pin configured
- Fixed SSDV image number not wrapping round
- Fixed frequency error calculation on Rx
- Allow for uplink if GPS lost
- Extend uplink options
- Fix GPU temperature only being read once if there's no DS18B20 (i.e. not using PITS board)
- Disable null packets for LoRa mode 0
- Pedestrian mode for UBlox
- Use Flight_Mode_Altitude setting to choose flight mode or pedestrian for UBlox and L80
- Set height and/or width to zero to tell raspistill to use full camera resolution for "full" mode images
- Removed some warnings from the latest gcc in Raspbian Buster
- Added support for Strobon V1 and V2 PWM-controlled LED strobe lights
- Added support for MS5611 Pressure/Temperature Sensor
- Added support for RTTY via LoRa module
- Added HABPack support for LoRa, using encoder by Phil Crump. Enable with LORA_HABPack_n=Y
- Fixed APRS pre-emphasis which was actually de-emphasis!
- Add LoRa mode 8 for SSDV repeater network
- Re-enabled temperature sensing for Pi Zero / W
- Print list of fields when sending first sentence for a channel. Useful for setting up payload document.
- Reduce amount of Rx-related guff when in listen-only mode
- Changed startup to use systemd
- Added support direct upload to Habitat using an internet connection
- Added support for Pi Zero W
- Added support for USB cameras via gphoto2
- Red (warn) LED now flashes during wait for GPS lock; if it's on without flashing then there is no GPS data (which means GPS misconfigured, or Pi revision not recognised)
- Full list of Pi Zero boards
- Ignore empty CRLF lines in pisky.txt
- Better CPU/Pi test
- Added SSDV_settings to pisky.txt - add command-line parameter when calling SSDV program- Removed support for running without device tree
- Fixed setting of implicit/explicit mode manually, ditto low-data-rate optimisation
- Truncate SSDV images larger than max size (currently 4096 packets)
- Settable delay between packets
- Minimal "buoy mode" telemetry
- Added option for serial GPS connection. Use GPS_Device=/dev/ttyACM0 for example.
- Re-enabled APRS script
- Fixed error where LoRa channel stopped transmitting after a few sentences if SSDV disabled on that channel
- Increased maximum size of SSDV file to 4096 packets
- Add option to disable reading of ADC, and also transmission of ADC values
- BME280 driver
- Ability to receive SMS-style messages uplinked from the ground via LoRa. Messages are saved to a text file and can then be processed externally (e.g. by supplied Python script to display on a Pi Sense HAT)
- Ability to include, in the LoRa telemetry, CSV data from an external file. Sample Python script supplied to build that file from Sense HAT sensor data.
- Ability to re-send SSDV packets, via LoRa, that were not received on the ground. Uses a LoRa uplink message to define which packets need to be sent.
- Can include uplink message status in LoRa telemetry.
- Photo sizes forced to be no smaller than 320x240, to avoid limitation in raspistill program.
- RTTY can be switched off (no data no carrier) during LoRa uplink periods.
- Use of EXIV2 (if installed) to insert telemetry data into all stored JPEG images, in the JPEG comment field
- Sample image processing script to extract telemetry from JPEG comment field, and insert into downloaded images as a text overlay, using ImageMagick
- Test for latest Pi boards; assume PITS+ if not a known board
- clear.txt now actually works
- Better setting of MTX2 frequency
28/11/2015
- Suport for Pi Zero
- Support for USB webcam via fswebcam
12/10/2015
- Added "camera_settings" option for config file
- Fixed IP check which faulted when Pi on a VPN
18/08/2015
- Merged in LoRa code (LoRa branch is now defunct)
- Photographs can now be taken at independent rates for RTTY, LoRa, full-size
- Landing prediction option
- Fixes for multiple DS18B20 sensors
- Ability to run emulated flight from GPS NMEA file
- Ability to modify SSDV images before transmission using ImageMagick etc.
- LoRa Calling Mode
- RTTY serial port kept open continuously
- Startup radio message with IP address etc.
- Stop multiple tracker programs from being run
- Test for latest Pi board
- Option to delete existing image files at startup
- Image files now in names/dated folders e.g. /home/pi/images/RTTY/18_08_2015
17/06/2015
- Merged in APRS code (APRS branch is now defunct)
- Added options to control when APRS packets are sent
- Fixed issue with tracker program failing SD card is pulled and APRS enabled
- NTX2 frequency-setting code now has same improvements as for MTX2
- Serial port kept open now instead of open/close each packet; using flush command to sync instead of closing. This allows ...
- ... Telemetry log entries now written whilst waiting for telemetry to Tx; removes/reduces delay due to SD card writing.
01/06/2015
- MTX2 frequency-setting code changed to fix random fails to set frequency
- logging now on by default
- log files removed from repository
- Long payload IDs are truncated to 6 before passing to SSDV program
- SSDV image widths and heights now forced to be multiples of 16 pixels
- Added support for second (external) DS18B20 temperature sensor
- Fix to occassional missing packets
- Support for Pi V2 B
- Protect against
- 085/180 being disconnected after initialisation
19/12/2014
- GPS code completely re-written to use WiringPi library instead of bcm library
- default configuration now leaves the monitor on, to ease development
- As the PITS+ boards are set by frequency in MHz, but the earlier board was set by channel number, the code now accepts either "frequency=nn" for channel number, of frequency=xxx.xxxMHz for actual frequency. Not that using the second form does not give you more options on the older board - the frequency will be set to the closest channnel.
- Camera filenames are now the system time
- Camera images are now saved in dated folders