Examples Customizations

config/examples/3DFabXYZ/Migbot/Configuration_adv.h

@@ -21,6 +21,8 @@
  */
 #pragma once
 
+#define CONFIG_EXAMPLES_DIR "3DFabXYZ/Migbot"
+
 /**
  * Configuration_adv.h
  *
@@ -535,14 +537,14 @@
  * The fan turns on automatically whenever any driver is enabled and turns
  * off (or reduces to idle speed) shortly after drivers are turned off.
  */
-//#define USE_CONTROLLER_FAN
+#define USE_CONTROLLER_FAN
 #if ENABLED(USE_CONTROLLER_FAN)
-  //#define CONTROLLER_FAN_PIN -1           // Set a custom pin for the controller fan
+  #define CONTROLLER_FAN_PIN  7             // Set a custom pin for the controller fan
   //#define CONTROLLER_FAN2_PIN -1          // Set a custom pin for second controller fan
   //#define CONTROLLER_FAN_USE_Z_ONLY       // With this option only the Z axis is considered
   //#define CONTROLLER_FAN_IGNORE_Z         // Ignore Z stepper. Useful when stepper timeout is disabled.
   #define CONTROLLERFAN_SPEED_MIN         0 // (0-255) Minimum speed. (If set below this value the fan is turned off.)
-  #define CONTROLLERFAN_SPEED_ACTIVE    255 // (0-255) Active speed, used when any motor is enabled
+  #define CONTROLLERFAN_SPEED_ACTIVE    127 // (0-255) Active speed, used when any motor is enabled
   #define CONTROLLERFAN_SPEED_IDLE        0 // (0-255) Idle speed, used when motors are disabled
   #define CONTROLLERFAN_IDLE_TIME        60 // (seconds) Extra time to keep the fan running after disabling motors
 
@@ -705,15 +707,15 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE
+#define CASE_LIGHT_ENABLE
 #if ENABLED(CASE_LIGHT_ENABLE)
-  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define CASE_LIGHT_PIN 11                   // Override the default pin if needed
   #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
-  #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
+  #define CASE_LIGHT_DEFAULT_ON false         // Set default power-up state on
   #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
   //#define CASE_LIGHT_NO_BRIGHTNESS          // Disable brightness control. Enable for non-PWM lighting.
   //#define CASE_LIGHT_MAX_PWM 128            // Limit PWM duty cycle (0-255)
-  //#define CASE_LIGHT_MENU                   // Add Case Light options to the LCD menu
+  #define CASE_LIGHT_MENU                     // Add Case Light options to the LCD menu
   #if ENABLED(NEOPIXEL_LED)
     //#define CASE_LIGHT_USE_NEOPIXEL         // Use NeoPixel LED as case light
   #endif
@@ -1016,7 +1018,7 @@
 
   // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
   #define G34_MAX_GRADE              5    // (%) Maximum incline that G34 will handle
-  #define Z_STEPPER_ALIGN_ITERATIONS 5    // Number of iterations to apply during alignment
+  #define Z_STEPPER_ALIGN_ITERATIONS 3    // Number of iterations to apply during alignment
   #define Z_STEPPER_ALIGN_ACC        0.02 // Stop iterating early if the accuracy is better than this
   #define RESTORE_LEVELING_AFTER_G34      // Restore leveling after G34 is done?
   // After G34, re-home Z (G28 Z) or just calculate it from the last probe heights?
@@ -1270,7 +1272,7 @@
  * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the
  * lowest stepping frequencies.
  */
-//#define ADAPTIVE_STEP_SMOOTHING
+#define ADAPTIVE_STEP_SMOOTHING
 
 /**
  * Custom Microstepping
@@ -1356,8 +1358,8 @@
 // Change values more rapidly when the encoder is rotated faster
 #define ENCODER_RATE_MULTIPLIER
 #if ENABLED(ENCODER_RATE_MULTIPLIER)
-  #define ENCODER_10X_STEPS_PER_SEC   30  // (steps/s) Encoder rate for 10x speed
-  #define ENCODER_100X_STEPS_PER_SEC  80  // (steps/s) Encoder rate for 100x speed
+  #define ENCODER_10X_STEPS_PER_SEC   75  // (steps/s) Encoder rate for 10x speed
+  #define ENCODER_100X_STEPS_PER_SEC  160 // (steps/s) Encoder rate for 100x speed
 #endif
 
 // Play a beep when the feedrate is changed from the Status Screen
@@ -1409,7 +1411,7 @@
   #endif
 
   // Include a page of printer information in the LCD Main Menu
-  //#define LCD_INFO_MENU
+  #define LCD_INFO_MENU
   #if ENABLED(LCD_INFO_MENU)
     //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
   #endif
@@ -1439,7 +1441,7 @@
   #endif
 
   // Scroll a longer status message into view
-  //#define STATUS_MESSAGE_SCROLLING
+  #define STATUS_MESSAGE_SCROLLING
 
   // Apply a timeout to low-priority status messages
   //#define STATUS_MESSAGE_TIMEOUT_SEC 30 // (seconds)
@@ -1551,7 +1553,7 @@
 
   //#define MEDIA_MENU_AT_TOP               // Force the media menu to be listed on the top of the main menu
 
-  #define EVENT_GCODE_SD_ABORT "G28XY"      // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")
+  #define EVENT_GCODE_SD_ABORT "G27"        // G-code to run on SD Abort Print (e.g., "G28XY" or "G27")
 
   #if ENABLED(PRINTER_EVENT_LEDS)
     #define PE_LEDS_COMPLETED_TIME  (30*60) // (seconds) Time to keep the LED "done" color before restoring normal illumination
@@ -1634,7 +1636,7 @@
   //#define LONG_FILENAME_WRITE_SUPPORT   // Create / delete files with long filenames via M28, M30, and Binary Transfer Protocol
   //#define M20_TIMESTAMP_SUPPORT         // Include timestamps by adding the 'T' flag to M20 commands
 
-  //#define SCROLL_LONG_FILENAMES         // Scroll long filenames in the SD card menu
+  #define SCROLL_LONG_FILENAMES           // Scroll long filenames in the SD card menu
 
   //#define SD_ABORT_NO_COOLDOWN          // Leave the heaters on after Stop Print (not recommended!)
 
@@ -2633,7 +2635,7 @@
  *
  * Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
   #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
@@ -2676,7 +2678,7 @@
   //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
   //#define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
 
-  //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
   //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif
 
@@ -3264,7 +3266,7 @@
  * Add the M240 G-code to take a photo.
  * The photo can be triggered by a digital pin or a physical movement.
  */
-//#define PHOTO_GCODE
+#define PHOTO_GCODE
 #if ENABLED(PHOTO_GCODE)
   // A position to move to (and raise Z) before taking the photo
   //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 }  // { xpos, ypos, zraise } (M240 X Y Z)
@@ -3273,17 +3275,17 @@
 
   // Canon RC-1 or homebrew digital camera trigger
   // Data from: https://www.doc-diy.net/photo/rc-1_hacked/
-  //#define PHOTOGRAPH_PIN 23
+  //#define PHOTOGRAPH_PIN 12
 
   // Canon Hack Development Kit
   // https://captain-slow.dk/2014/03/09/3d-printing-timelapses/
-  //#define CHDK_PIN        4
+  #define CHDK_PIN       12
 
   // Optional second move with delay to trigger the camera shutter
   //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS }  // { xpos, ypos } (M240 I J)
 
   // Duration to hold the switch or keep CHDK_PIN high
-  //#define PHOTO_SWITCH_MS   50 // (ms) (M240 D)
+  #define PHOTO_SWITCH_MS   50 // (ms) (M240 D)
 
   /**
    * PHOTO_PULSES_US may need adjustment depending on board and camera model.
@@ -3735,33 +3737,29 @@
 // @section custom main menu
 
 // Custom Menu: Main Menu
-//#define CUSTOM_MENU_MAIN
+#define CUSTOM_MENU_MAIN
 #if ENABLED(CUSTOM_MENU_MAIN)
-  //#define CUSTOM_MENU_MAIN_TITLE "Custom Commands"
-  #define CUSTOM_MENU_MAIN_SCRIPT_DONE "M117 User Script Done"
+  #define CUSTOM_MENU_MAIN_TITLE "Tools"
+  #define CUSTOM_MENU_MAIN_SCRIPT_DONE "M117 Done"
   #define CUSTOM_MENU_MAIN_SCRIPT_AUDIBLE_FEEDBACK
   //#define CUSTOM_MENU_MAIN_SCRIPT_RETURN   // Return to status screen after a script
   #define CUSTOM_MENU_MAIN_ONLY_IDLE         // Only show custom menu when the machine is idle
 
-  #define MAIN_MENU_ITEM_1_DESC "Home & UBL Info"
-  #define MAIN_MENU_ITEM_1_GCODE "G28\nG29 W"
+  #define MAIN_MENU_ITEM_1_DESC "Probe Mesh&Save"
+  #define MAIN_MENU_ITEM_1_GCODE "G28\nG29 P1\nG29 P3 T0\nG29 S0 A F10\nG29 J2\nM500"
   //#define MAIN_MENU_ITEM_1_CONFIRM          // Show a confirmation dialog before this action
 
-  #define MAIN_MENU_ITEM_2_DESC "Preheat for " PREHEAT_1_LABEL
-  #define MAIN_MENU_ITEM_2_GCODE "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
+  #define MAIN_MENU_ITEM_2_DESC "Manual Mesh&Save"
+  #define MAIN_MENU_ITEM_2_GCODE "G28\nG29 P4 R999 T\nG29 S0 A F10\nM500"
   //#define MAIN_MENU_ITEM_2_CONFIRM
 
-  //#define MAIN_MENU_ITEM_3_DESC "Preheat for " PREHEAT_2_LABEL
-  //#define MAIN_MENU_ITEM_3_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
+  #define MAIN_MENU_ITEM_3_DESC "Print Test Pattern"
+  #define MAIN_MENU_ITEM_3_GCODE "G26 C P O2.25" // Do a typical test sequence
   //#define MAIN_MENU_ITEM_3_CONFIRM
 
-  //#define MAIN_MENU_ITEM_4_DESC "Heat Bed/Home/Level"
-  //#define MAIN_MENU_ITEM_4_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
+  #define MAIN_MENU_ITEM_4_DESC "Move Bed Forward"
+  #define MAIN_MENU_ITEM_4_GCODE "G28 X0 Y0\nG1 X0 Y180 F3000\nM84" // move X/Y to min endstops & Feed the bed forward & steppers off
   //#define MAIN_MENU_ITEM_4_CONFIRM
-
-  //#define MAIN_MENU_ITEM_5_DESC "Home & Info"
-  //#define MAIN_MENU_ITEM_5_GCODE "G28\nM503"
-  //#define MAIN_MENU_ITEM_5_CONFIRM
 #endif
 
 // @section custom config menu