Merge tag '2.0.9.1' into 2.0.x_cr30

Marlin/Configuration.h

@@ -35,7 +35,7 @@
  *
  * Advanced settings can be found in Configuration_adv.h
  */
-#define CONFIGURATION_H_VERSION 02000900
+#define CONFIGURATION_H_VERSION 02000901
 
 //===========================================================================
 //============================= Getting Started =============================
@@ -1255,7 +1255,8 @@
   //#define WAIT_FOR_HOTEND         // Wait for hotend to heat back up between probes (to improve accuracy & prevent cold extrude)
 #endif
 //#define PROBING_FANS_OFF          // Turn fans off when probing
-//#define PROBING_STEPPERS_OFF      // Turn steppers off (unless needed to hold position) when probing
+//#define PROBING_ESTEPPERS_OFF     // Turn all extruder steppers off when probing
+//#define PROBING_STEPPERS_OFF      // Turn all steppers off (unless needed to hold position) when probing (including extruders)
 //#define DELAY_BEFORE_PROBING 200  // (ms) To prevent vibrations from triggering piezo sensors
 
 // Require minimum nozzle and/or bed temperature for probing

Marlin/Configuration_adv.h

@@ -30,7 +30,7 @@
  *
  * Basic settings can be found in Configuration.h
  */
-#define CONFIGURATION_ADV_H_VERSION 02000900
+#define CONFIGURATION_ADV_H_VERSION 02000901
 
 //===========================================================================
 //============================= Thermal Settings ============================
@@ -1594,7 +1594,7 @@
    */
   //#define STATUS_COMBINE_HEATERS    // Use combined heater images instead of separate ones
   //#define STATUS_HOTEND_NUMBERLESS  // Use plain hotend icons instead of numbered ones (with 2+ hotends)
-  #define STATUS_HOTEND_INVERTED      // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM)
+  #define STATUS_HOTEND_INVERTED      // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM for numbered hotends)
   #define STATUS_HOTEND_ANIM          // Use a second bitmap to indicate hotend heating
   #define STATUS_BED_ANIM             // Use a second bitmap to indicate bed heating
   #define STATUS_CHAMBER_ANIM         // Use a second bitmap to indicate chamber heating
@@ -1988,9 +1988,9 @@
     // calibration.
     //#define BTC_PROBE_TEMP    30  // (°C)
 
-    // Height above Z=0.0f to raise the nozzle. Lowering this can help the probe to heat faster.
-    // Note: the Z=0.0f offset is determined by the probe offset which can be set using M851.
-    //#define PTC_PROBE_HEATING_OFFSET 0.5f
+    // Height above Z=0.0 to raise the nozzle. Lowering this can help the probe to heat faster.
+    // Note: the Z=0.0 offset is determined by the probe offset which can be set using M851.
+    //#define PTC_PROBE_HEATING_OFFSET 0.5
 
     // Height to raise the Z-probe between heating and taking the next measurement. Some probes
     // may fail to untrigger if they have been triggered for a long time, which can be solved by
@@ -2892,7 +2892,7 @@
    *
    * It is recommended to set HOMING_BUMP_MM to { 0, 0, 0 }.
    *
-   * SPI_ENDSTOPS  *** Beta feature! *** TMC2130 Only ***
+   * SPI_ENDSTOPS  *** Beta feature! *** TMC2130/TMC5160 Only ***
    * Poll the driver through SPI to determine load when homing.
    * Removes the need for a wire from DIAG1 to an endstop pin.
    *

Marlin/Version.h

@@ -28,7 +28,7 @@
 /**
  * Marlin release version identifier
  */
-//#define SHORT_BUILD_VERSION "2.0.9"
+//#define SHORT_BUILD_VERSION "2.0.9.1"
 
 /**
  * Verbose version identifier which should contain a reference to the location
@@ -41,7 +41,7 @@
  * here we define this default string as the date where the latest release
  * version was tagged.
  */
-//#define STRING_DISTRIBUTION_DATE "2021-06-15"
+//#define STRING_DISTRIBUTION_DATE "2021-06-27"
 
 /**
  * Defines a generic printer name to be output to the LCD after booting Marlin.