This fork supports CAN bus communication with inverters supporting the CANBUS Protocol compatible with Pylontech V1.3 and Goodwe V1.5. Additionaly values of Deye inverters are read via RS485 via Modbus. All values are send to Home Assistant.
Note Pylontech uses 15s/48v Goodwe uses 16s/51.2v @3.2v/cell nominal. Other battery profiles that utilise the pylonton/goodwe protocol with differnt cell counts may also work, eg Alpha Ess Smile, BYD Battery-Box LV Flex Lite Select the correct battery profile in the inverter to match your battery pack!
The ESP32 communicates with the JK-BMS using the RS485 port(GPS) which is in fact not RS485, it is 3.3V TTL so it can be directly connected to the ESP32. The ESP32 then sends the required CAN bus data to the inverter via a CAN bus transceiver.
To read the values from the Inverter the ESP32 communicates via RS485 transreceiver.
- Battery Voltage
- Battery Current (+charge, -discharge)
- State of Charge (SOC)
- State of health (SOH)
- BMS Temperature
- Charging Voltage
- Charging Amps
- Discharge min Voltage
- Battery name
- Alarms: Cell over/under voltage, Charge/discharge over current, High/low Temp, BMS fault
- Charging logic: Complete rework of the charging logic, now charges with constant current(CC) to the absorption voltage, then has an absorption timer (Constant Voltage, user configurable time), with rebulk feature (user configurable offset from absorption voltage).
- Controls to manage inverter remotely
- Set "Balance Voltage" to tell inverter to only charge till this voltage
- Set "Min Discharge Voltage" to tell inverter stop discharging below this voltage
- Set "Charging Current"
- Set "Discharging Current"
- Disable/Enable inverter charging
- Disable/Enable inverter discharging
- Disable/Enable top balance charging
- Set "Days Bewteen Balancing" to only balance every x days, in between it will stop charging when "Max Charge %" is reached
- Set "Max Charge %" for days in between top balance cycles (on top balance days it will charge till "Balance Voltage")
- Set "Min Discharge %" to stop discharging
Inverters supporting CAN Pylon/Goodwe Low Voltage protocol should work, check your inverter manual to confirm.
The following are confirmed and known to work:
- Deye SUN-12K-SG04LP3-EU
All JK-BMS models with software version >=6.0 are using the implemented protocol and should be supported.
- JK-BD6A17S6P, hw 7.2, sw 7.1.0H
- JK-BD6A17S8P, hw 9.x, sw 9.01G (reported by @jonadis)
- JK-BD6A20S10P, hw 10.XW, sw 10.07 (reported by @adadrag)
- JK-BD6A24S6P, hw 6.x, sw 6.10S (reported by @ziporah)
- JK-BD6A24S10P, hw 8.x, sw 8.0.6G (reported by @spoonwzd)
- JK-BD4A17S4P, hw 11.xw, sw 11.01 (reported by @Condor-XYZ)
- JK-B1A24S15P, hw 8.x, sw 8.1.0H (reported by @killee)
- JK-B1A20S15P, hw 8.x, sw 8.14U (reported by @trippfam07)
- JK-B2A24S15P, hw 6.x, sw 6.1.3S (reported by @miguel300477)
- JK-B2A24S15P, hw 8.x, sw 8.21W (reported by @mariusvaida)
- JK-B2A24S15P, hw 10.xw, sw 10.07
- JK-B2A24S15P, hw 10.xw, sw 10.08 (reported by @meccip)
- JK-B2A24S20P, hw 8.x, sw 8.1.2H (reported by @KlausLi)
- JK-B2A24S20P, hw 8.x, sw 8.20G (reported by @rob-oravec)
- JK-B2A24S20P, hw 10.X-W, sw 10.02 (reported by @SeByDocKy)
- JK-B2A24S20P, hw 10.XG, sw 10.07D30 (reported by @TheSmartGerman)
- JK-B2A24S20P, hw 10.XW, sw 10.07 (reported by @amagr0)
- JK-B2A8S20P, hw 9.x, sw 9.01M3 (reported by @EasilyBoredEngineer)
- JK-B2A8S20P, hw 9.x, sw 9.08W (reported by @vrabi-cv)
- JK-B2A8S20P, hw 11.XW, sw 11.17 (reported by @senfkorn)
- JK-B2A20S20P, hw 10.XW, sw 10.09 (reported by @markusgg84)
- JK-B5A24S, hw 8.x, sw 8.0.3M, using
JK04(reported by @JSladen) - GW-24S4EB (NEEY/Heltec 4A Smart Active Balancer), hw HW-2.8.0, sw ZH-1.2.3 (reported by @cristi2005)
- ESPHome 2022.11.0 or higher.
- Optimized for ESP32-S2 because of lower power consumption but works with Generic ESP32 as well
- TJA1050 CAN controller interface module and 4.7K resistor for 5v to 3.3v level shifing.
- Optional: JK RS485 Adaptor and RS484 to TTL3.3v Adaptor (see optional schematic below)
I have designed and build a PCB pictured below. This has all the hardware needed to communicate with BMS and Inverter via CAN bus and Modbus. It is a plug and play device, just connect the 4 pin headder in the BMS and a LAN cable to the Inverter.
HJDC-PCB
Deye BMS LAN Port (RJ45)
ESP32-S2 Wemos Mini
Optional below, as seen in pic above: RS485 between JK-BMS GPS port and ESP32-S2 Wemos Mini, uses JK RS485 adaptor and RS485 to TTL3.3v adaptor.
┌──────────┐ ┌───────────┐ ┌─────────┐ ┌───────────┐
│ │ │ 7│<TX-----TX>| | | |
│ JK-BMS │<TX ----------------------- RX>│16 9│<RX-----RX>| TJA1050 |<- CAN H ->|4 |
│ GPS Port │<RX ----------------------- TX>│18 │<-- GND ->| CAN |<- CAN L ->|5 |
│ │ ┌──────────┐ │ │<-- 3.3V ->| | | Inverter |
│ 60V│<- VBus ->│ DC/DC │<- 5V ->│ ESP32-S2 │ └─────────┘ │ LAN │
│ │<- GND ->│ Converter│<- GND ->│ Wemos │ │ BMS │
└──────────┘ | 60V/5V | │ Mini │ ┌─────────┐ │ │
└──────────┘ │ 11│<TX-----TX>│ │<-- GND -->│6 │
│ 12│<RX-----RX>│ RS485 │<-- A -->│7 │
│ │<-- GND ->│ to TTL │<-- B -->│8 │
│ │<-- 3.3V ->│ │ │ │
└───────────┘ └─────────┘ └───────────┘
Esp32 Dev Kit Board
┌──────────┐ ┌───────────┐ ┌─────────┐ ┌───────────┐
│ │ │ 23│<TX-----TX>| | | |
│ JK-BMS │<TX ----------------------- RX>│16 22│<RX-----RX>| TJA1050 |<- CAN H ->|4 |
│ │<RX ----------------------- TX>│17 │<---GND--->| CAN |<- CAN L ->|5 |
│ │ ┌──────────┐ │ │<---3.3V-->| | | Inverter |
│ 60V│<- VBus ->│ DC/DC │<- 5V ->│ ESP32 │ └─────────┘ │ LAN │
│ │<- GND ->│ Converter│<- GND ->│ Dev Kit │ │ BMS │
└──────────┘ | 60V/5V | │ │ ┌─────────┐ │ │
└──────────┘ │ 19│<TX-----TX>│ │<-- GND -->│6 │
│ 18│<RX-----RX>│ RS485 │<-- A -->│7 │
│ │<-- GND ->│ to TTL │<-- B -->│8 │
│ │<-- 3.3V ->│ │ │ │
└───────────┘ └─────────┘ └───────────┘
# RS485-TTL jack on JK-BMS (4 Pin, JST 1.25mm pitch)
┌─── ─────── ────┐
│ │
│ O O O O │
│GND RX TX VBAT│
└────────────────┘
│ │ │ | VBAT is full battery volatge eg 55.3V (Used as power supply for 60V/5V DC/DC converter)
│ │ └──── ESP32-S2 GPIO18 (`rx_pin`)
│ └──────── ESP32-S2 GPIO16 (`tx_pin`)
└──────────── GND
The RS485-TTL jack of the BMS can be attached to any UART pins of the ESP. A hardware UART should be preferred because of the high baudrate (115200 baud). The connector is called 4 Pin JST with 1.25mm pitch.
You can install this component with ESPHome external components feature like this:
external_components:
- source: github://Ackmaniac/esphome-jk-bms-can@mainor just use the esp32-example-can-deye-modbus_espidf.yaml as proof of concept:
# Install esphome
pip3 install esphome
# Clone this external component
git clone https://github://Ackmaniac/esphome-jk-bms-can.git
cd esphome-jk-bms-can
# Create a secrets.yaml containing some setup specific secrets
cat > secrets.yaml <<EOF
wifi_ssid: MY_WIFI_SSID
wifi_password: MY_WIFI_PASSWORD
# Validate the configuration, create a binary, upload it, and start logs
esphome run esp32-example-can-deye-modbus_espidf.yaml
# Optional add to Home Assistant
In Home Assistant under settings->Intergration "Add Intergration" select ESPHome add device jk-bms-can if found or supply ip address of ESP32
[main:141]: send can id: 0x359 hex: 0 0 0 0 3 0 0 0
[canbus:033]: send extended id=0x359 rtr=FALSE size=8
[main:187]: send can id: 0x351 hex: 28 2 e8 3 e8 3 a0 1
[canbus:033]: send extended id=0x351 rtr=FALSE size=8
[main:199]: send can id: 0x355 hex: 4f 0 64 0
[canbus:033]: send extended id=0x355 rtr=FALSE size=4
[main:213]: send can id: 0x356 hex: 63 14 62 fc 86 1
[canbus:033]: send extended id=0x356 rtr=FALSE size=6
[canbus:070]: received can message (#1) std can_id=0x305 size=8
[light:035]: 'Builtin LED' Setting:
[light:046]: State: OFF
[main:238]: send can id: 0x35C hex: c0 0
[canbus:033]: send extended id=0x35c rtr=FALSE size=2
[canbus:033]: send extended id=0x35e rtr=FALSE size=8
- The battery type sensor is pretty useless because the BMS reports always the same value (
Ternary Lithium). Regardless of which battery type was set / parameter set was loaded via the android app. (#9) - ESP32: Adding all supported sensors can lead to a stack overflow / boot loop. This can be solved by increasing the stack size. (#63)
If this component doesn't work out of the box for your device please update your configuration to enable the debug output of the UART component and increase the log level to the see outgoing and incoming serial traffic:
logger:
level: DEBUG
uart:
id: uart0
baud_rate: 115200
rx_buffer_size: 384
tx_pin: GPIO14
rx_pin: GPIO4
debug:
direction: BOTH
- https://github.com/uksa007/esphome-jk-bms-can.git Thanks go to uksa007 for help and making the original CAN communication code!
- https://github.com/syssi/esphome-jk-bms Thanks go to syssi for help and making the original RS485 code!
- https://secondlifestorage.com/index.php?threads/jk-b1a24s-jk-b2a24s-active-balancer.9591/
- https://github.com/jblance/jkbms
- jblance/mpp-solar#112
- https://github.com/jblance/mpp-solar/blob/master/mppsolar/protocols/jk232.py
- https://github.com/jblance/mpp-solar/blob/master/mppsolar/protocols/jk485.py
- https://github.com/sshoecraft/jktool
- https://github.com/Louisvdw/dbus-serialbattery/blob/master/etc/dbus-serialbattery/jkbms.py
- https://blog.ja-ke.tech/2020/02/07/ltt-power-bms-chinese-protocol.html
- https://blog.ja-ke.tech/2020/02/07/ltt-power-bms-chinese-protocol.html
type: entities
title: HJDC Settings
entities:
- entity: sensor.hjdc_charging_status
name: Charging Status
- entity: number.hjdc_balance_voltage
name: Balance Voltage
- entity: number.hjdc_min_discharge_voltage
name: Min Discharge Voltage
- entity: number.hjdc_charging_current_max
name: Charging Current Max
- entity: number.hjdc_discharging_current_max
name: Discharging Current Max
- entity: switch.hjdc_charging_enabled
name: Charging Enabled
- entity: switch.hjdc_discharge_enabled
name: Discharge Enabled
- entity: switch.hjdc_charging_top_balance
name: Charging top balance
- entity: number.hjdc_days_between_balancing
name: Days Between Balancing
- entity: sensor.hjdc_next_top_balance
name: Next Top Balance
- entity: number.hjdc_max_charge
name: Max Charge %
- entity: number.hjdc_min_discharge
name: Min Discharge %
type: entities
entities:
- entity: sensor.hjdc_charging_status
name: Charging Status
- entity: number.hjdc_balance_voltage
name: Balance Voltage
- entity: number.hjdc_min_discharge_voltage
name: Min Discharge Voltage
- entity: number.hjdc_charging_current_max
name: Charging Current Max
- entity: number.hjdc_discharging_current_max
name: Discharging Current Max
- entity: switch.hjdc_charging_enabled
name: Charging Enabled
- entity: switch.hjdc_discharge_enabled
name: Discharge Enabled
- entity: switch.hjdc_charging_top_balance
name: Charging top balance
- entity: number.hjdc_days_between_balancing
name: Days Between Balancing
- entity: number.hjdc_max_charge
name: Max Charge %
- entity: number.hjdc_min_discharge
name: Min Discharge %
show_name: true
show_icon: true
show_state: true
type: glance
columns: 4
entities:
- entity: sensor.hjdc_deye_internal_grid_l1_power
name: Internal L1
- entity: sensor.hjdc_deye_internal_grid_l2_power
name: Internal L2
- entity: sensor.hjdc_deye_internal_grid_l2_power
name: Internal L3
- entity: sensor.hjdc_deye_internal_grid_total_power
name: Internal Total
- entity: sensor.hjdc_deye_external_grid_l1_power
name: External L1
- entity: sensor.hjdc_deye_external_grid_l2_power
name: External L2
- entity: sensor.hjdc_deye_external_grid_l3_power
name: External L3
- entity: sensor.hjdc_deye_external_grid_total_power
name: External Total
- entity: sensor.hjdc_deye_load_l1_power
name: Load L1
- entity: sensor.hjdc_deye_load_l2_power
name: Load L2
- entity: sensor.hjdc_deye_load_l3_power
name: Load L3
- entity: sensor.hjdc_deye_load_total_power
name: Load Total
show_name: true
show_icon: true
show_state: true
type: glance
entities:
- entity: sensor.hjdc_jk_temperature_sensor_1
name: Battery 1
- entity: sensor.hjdc_jk_temperature_sensor_2
name: Battery 1
- entity: sensor.hjdc_jk_power_tube_temperature
name: BMS
- entity: sensor.hjdc_jk_temperature_wire
name: Room
state_color: false
show_name: true
show_icon: true
show_state: true
type: glance
columns: 6
entities:
- entity: sensor.hjdc_jk_min_cell_voltage
name: min
- entity: sensor.hjdc_jk_max_cell_voltage
name: max
- entity: sensor.hjdc_jk_delta_cell_voltage
name: delta
- entity: binary_sensor.hjdc_jk_balancing
name: balance
- entity: sensor.hjdc_jk_min_voltage_cell
name: min C
- entity: sensor.hjdc_jk_max_voltage_cell
name: max C
type: glance
columns: 5
entities:
- entity: sensor.hjdc_jk_power
name: power
- entity: sensor.hjdc_jk_current
name: A
- entity: sensor.hjdc_jk_total_voltage
name: V
- entity: sensor.hjdc_jk_capacity_remaining
name: SOC
- entity: sensor.hjdc_jk_capacity_remaining_derived
name: Ah
show_name: true
show_icon: false
show_state: true
type: glance
title: Cells
columns: 4
entities:
- entity: sensor.hjdc_jk_cell_voltage_1
name: '1'
- entity: sensor.hjdc_jk_cell_voltage_2
name: '2'
- entity: sensor.hjdc_jk_cell_voltage_3
name: '3'
- entity: sensor.hjdc_jk_cell_voltage_4
name: '4'
- entity: sensor.hjdc_jk_cell_voltage_5
name: '5'
- entity: sensor.hjdc_jk_cell_voltage_6
name: '6'
- entity: sensor.hjdc_jk_cell_voltage_7
name: '7'
- entity: sensor.hjdc_jk_cell_voltage_8
name: '8'
- entity: sensor.hjdc_jk_cell_voltage_9
name: '9'
- entity: sensor.hjdc_jk_cell_voltage_10
name: '10'
- entity: sensor.hjdc_jk_cell_voltage_11
name: '11'
- entity: sensor.hjdc_jk_cell_voltage_12
name: '12'
- entity: sensor.hjdc_jk_cell_voltage_13
name: '13'
- entity: sensor.hjdc_jk_cell_voltage_14
name: '14'
- entity: sensor.hjdc_jk_cell_voltage_15
name: '15'
- entity: sensor.hjdc_jk_cell_voltage_16
name: '16'
type: entities
title: Deye
entities:
- entity: sensor.hjdc_deye_heat_sink_temperature
name: Heat Sink Temperature
- entity: sensor.hjdc_deye_battery_output_power
name: Battery Output Power
- entity: sensor.hjdc_deye_battery_capacity
name: Battery Capacity
- entity: sensor.hjdc_deye_battery_output_current
name: Battery Output Current
- entity: sensor.hjdc_deye_battery_temperature
name: Battery Temperature
- entity: sensor.hjdc_deye_battery_total_charge
name: Battery Total Charge
- entity: sensor.hjdc_deye_battery_total_discharge
name: Battery Total Discharge
- entity: sensor.hjdc_deye_battery_voltage
name: Battery Voltage
- entity: sensor.hjdc_deye_daily_battery_charge
name: Daily Battery Charge
- entity: sensor.hjdc_deye_daily_battery_discharge
name: Daily Battery Discharge
- entity: sensor.hjdc_deye_daily_energy_bought
name: Daily Energy Bought
- entity: sensor.hjdc_deye_daily_energy_sold
name: Daily Energy Sold
- entity: sensor.hjdc_deye_daily_load_consumption
name: Daily Load Consumption
- entity: sensor.hjdc_deye_daily_production
name: Daily Production
- entity: sensor.hjdc_deye_daily_pv1_production
name: Daily PV1 Production
- entity: sensor.hjdc_deye_daily_pv2_production
name: Daily PV2 Production
- entity: sensor.hjdc_deye_failure_status_of_communication_board
name: Failure status of communication board
- entity: sensor.hjdc_deye_grid_current_l1
name: Grid Current L1
- entity: sensor.hjdc_deye_grid_current_l2
name: Grid Current L2
- entity: sensor.hjdc_deye_grid_current_l3
name: Grid Current L3
- entity: sensor.hjdc_deye_grid_voltage_l1
name: Grid Voltage L1
- entity: sensor.hjdc_deye_grid_voltage_l2
name: Grid Voltage L2
- entity: sensor.hjdc_deye_grid_voltage_l3
name: Grid Voltage L3
- entity: sensor.hjdc_deye_external_grid_l1_power
name: External Grid L1 Power
- entity: sensor.hjdc_deye_external_grid_l2_power
name: External Grid L2 Power
- entity: sensor.hjdc_deye_external_grid_l3_power
name: External Grid L3 Power
- entity: sensor.hjdc_deye_external_grid_total_power
name: External Grid Total Power
- entity: sensor.hjdc_deye_internal_grid_l1_power
name: Internal Grid L1 Power
- entity: sensor.hjdc_deye_internal_grid_l2_power
name: Internal Grid L2 Power
- entity: sensor.hjdc_deye_internal_grid_l3_power
name: Internal Grid L3 Power
- entity: sensor.hjdc_deye_internal_grid_total_power
name: Internal Grid Total Power
- entity: sensor.hjdc_deye_inverter_frequency
name: Inverter Frequency
- entity: sensor.hjdc_deye_load_frequency
name: Load Frequency
- entity: sensor.hjdc_deye_load_total_power
name: Load Total Power
- entity: sensor.hjdc_deye_power_generation_today
name: Power Generation Today
- entity: sensor.hjdc_deye_pv1_current
name: PV1 Current
- entity: sensor.hjdc_deye_pv1_power
name: PV1 Power
- entity: sensor.hjdc_deye_pv1_voltage
name: PV1 Voltage
- entity: sensor.hjdc_deye_pv2_current
name: PV2 Current
- entity: sensor.hjdc_deye_pv2_power
name: PV2 Power
- entity: sensor.hjdc_deye_pv2_voltage
name: PV2 Voltage
- entity: sensor.hjdc_deye_pv_total_power
name: PV Total Power
- entity: sensor.hjdc_deye_running_status
name: Running Status
- entity: sensor.hjdc_deye_total_consumption
name: Total Consumption
- entity: sensor.hjdc_deye_total_energy_bought
name: Total Energy Bought
- entity: sensor.hjdc_deye_total_energy_sold
name: Total Energy Sold
- entity: sensor.hjdc_deye_total_grid_power
name: Total Grid Power
- entity: sensor.hjdc_deye_total_pv_production
name: Total PV Production
- entity: sensor.hjdc_deye_warning_1
name: Warning 1
- entity: sensor.hjdc_deye_warning_2
name: Warning 2
- entity: sensor.hjdc_deye_error_1
name: Error 1
- entity: sensor.hjdc_deye_error_2
name: Error 2
- entity: sensor.hjdc_deye_error_3
name: Error 3
- entity: sensor.hjdc_deye_error_4
name: Error 4
type: entities
title: JK
entities:
- entity: sensor.hjdc_jk_actual_battery_capacity
name: Actual Battery Capacity
- entity: sensor.hjdc_jk_alarm_low_volume
name: Alarm Low Volume
- entity: sensor.hjdc_jk_average_cell_voltage
name: Average Cell Voltage
- entity: sensor.hjdc_jk_balance_opening_pressure_difference
name: Balance Opening Pressure Difference
- entity: sensor.hjdc_jk_balance_starting_voltage
name: Balance Starting Voltage
- entity: binary_sensor.hjdc_jk_balancing
name: Balancing
- entity: binary_sensor.hjdc_jk_balancing_switch
name: Balancing Switch
- entity: sensor.hjdc_jk_battery_strings
name: Battery Strings
- entity: sensor.hjdc_jk_battery_type
name: Battery Type
- entity: sensor.hjdc_jk_capacity_remaining
name: Capacity Remaining
- entity: sensor.hjdc_jk_capacity_remaining_derived
name: Capacity Remaining Derived
- entity: sensor.hjdc_jk_cell_pressure_difference_protection
name: Cell Pressure Difference Protection
- entity: sensor.hjdc_jk_cell_voltage_overvoltage_delay
name: Cell Voltage Overvoltage Delay
- entity: sensor.hjdc_jk_cell_voltage_overvoltage_protection
name: Cell Voltage Overvoltage Protection
- entity: sensor.hjdc_jk_cell_voltage_overvoltage_recovery
name: Cell Voltage Overvoltage Recovery
- entity: sensor.hjdc_jk_cell_voltage_undervoltage_delay
name: Cell Voltage Undervoltage Delay
- entity: sensor.hjdc_jk_cell_voltage_undervoltage_protection
name: Cell Voltage Undervoltage Protection
- entity: sensor.hjdc_jk_cell_voltage_undervoltage_recovery
name: Cell Voltage Undervoltage Recovery
- entity: sensor.hjdc_jk_cells
name: Cells
- entity: binary_sensor.hjdc_jk_charging
name: Charging
- entity: sensor.hjdc_jk_charging_cycles
name: Charging Cycles
- entity: sensor.hjdc_jk_charging_high_temperature_protection
name: Charging High Temperature Protection
- entity: sensor.hjdc_jk_charging_low_temperature_protection
name: Charging Low Temperature Protection
- entity: sensor.hjdc_jk_charging_low_temperature_recovery
name: Charging Low Temperature Recovery
- entity: sensor.hjdc_jk_charging_overcurrent_delay
name: Charging Overcurrent Delay
- entity: sensor.hjdc_jk_charging_overcurrent_protection
name: Charging Overcurrent Protection
- entity: sensor.hjdc_jk_charging_power
name: Charging Power
- entity: binary_sensor.hjdc_jk_charging_switch
name: Charging Switch
- entity: sensor.hjdc_jk_current
name: Current
- entity: sensor.hjdc_jk_current_calibration
name: Current Calibration
- entity: binary_sensor.hjdc_jk_dedicated_charger_switch
name: Dedicated Charger Switch
- entity: sensor.hjdc_jk_delta_cell_voltage
name: Delta Cell Voltage
- entity: sensor.hjdc_jk_device_address
name: Device Address
- entity: sensor.hjdc_jk_device_type
name: Device Type
- entity: binary_sensor.hjdc_jk_discharging
name: Discharging
- entity: sensor.hjdc_jk_discharging_high_temperature_protection
name: Discharging High Temperature Protection
- entity: sensor.hjdc_jk_discharging_low_temperature_protection
name: Discharging Low Temperature Protection
- entity: sensor.hjdc_jk_discharging_low_temperature_recovery
name: Discharging Low Temperature Recovery
- entity: sensor.hjdc_jk_discharging_overcurrent_delay
name: Discharging Overcurrent Delay
- entity: sensor.hjdc_jk_discharging_overcurrent_protection
name: Discharging Overcurrent Protection
- entity: sensor.hjdc_jk_discharging_power
name: Discharging Power
- entity: binary_sensor.hjdc_jk_discharging_switch
name: Discharging Switch
- entity: sensor.hjdc_jk_errors
name: Errors
- entity: sensor.hjdc_jk_errors_bitmask
name: Errors Bitmask
- entity: sensor.hjdc_jk_manufacturer
name: Manufacturer
- entity: sensor.hjdc_jk_manufacturing_date
name: Manufacturing Date
- entity: sensor.hjdc_jk_max_cell_voltage
name: Max Cell Voltage
- entity: sensor.hjdc_jk_max_voltage_cell
name: Max Voltage Cell
- entity: sensor.hjdc_jk_min_cell_voltage
name: Min Cell Voltage
- entity: sensor.hjdc_jk_min_voltage_cell
name: Min Voltage Cell
- entity: sensor.hjdc_jk_operation_mode
name: Operation Mode
- entity: sensor.hjdc_jk_operation_mode_bitmask
name: Operation Mode Bitmask
- entity: sensor.hjdc_jk_password
name: Password
- entity: sensor.hjdc_jk_power
name: Power
- entity: sensor.hjdc_jk_power_tube_temperature
name: Power Tube Temperature
- entity: sensor.hjdc_jk_power_tube_temperature_protection
name: Power Tube Temperature Protection
- entity: sensor.hjdc_jk_power_tube_temperature_recovery
name: Power Tube Temperature Recovery
- entity: sensor.hjdc_jk_sleep_wait_time
name: Sleep Wait Time
- entity: sensor.hjdc_jk_software_version
name: Software Version
- entity: sensor.hjdc_jk_temperature_sensor_1
name: Temperature Sensor 1
- entity: sensor.hjdc_jk_temperature_sensor_2
name: Temperature Sensor 2
- entity: sensor.hjdc_jk_temperature_sensor_temperature_difference_protection
name: Temperature Sensor Temperature Difference Protection
- entity: sensor.hjdc_jk_temperature_sensor_temperature_protection
name: Temperature Sensor Temperature Protection
- entity: sensor.hjdc_jk_temperature_sensor_temperature_recovery
name: Temperature Sensor Temperature Recovery
- entity: sensor.hjdc_jk_temperature_sensors
name: Temperature Sensors
- entity: sensor.hjdc_jk_temperature_wire
name: Temperature Wire
- entity: sensor.hjdc_jk_total_battery_capacity_setting
name: Total Battery Capacity Setting
- entity: sensor.hjdc_jk_total_charging_cycle_capacity
name: Total Charging Cycle Capacity
- entity: sensor.hjdc_jk_total_runtime
name: Total Runtime
- entity: sensor.hjdc_jk_total_runtime_formatted
name: Total Runtime Formatted
- entity: sensor.hjdc_jk_total_voltage
name: Total Voltage
- entity: sensor.hjdc_jk_total_voltage_overvoltage_protection
name: Total Voltage Overvoltage Protection
- entity: sensor.hjdc_jk_total_voltage_undervoltage_protection
name: Total Voltage Undervoltage Protection