forked from phnxdrgn536/FLSun-v400
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathreadme.txt
76 lines (39 loc) · 5.38 KB
/
readme.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
English:
1.backup and save a copy of your V400 files that were loaded into cura from the FLSUN thumb drive and then remove these files from cura (or start with a clean install)
2. Open cura and select Help-->Show Configuration Folder
3. Place the "flsun_v400_extruder" folder in the "extruders" directory under the cura configuration path.
4. Place the "flsun_v400_intent" folder in the "intent" directory under the cura configuration path.
5. Place the "flsun_v400_quality" folder in the "quality" directory under the cura configuration path.
6. Place the "flsun_v400_variants" folder in the "variants" directory under the cura configuration path. (NOTE: only copy the nozzle sizes you want to use if you dont want all nozzle sizes to be shown)
7. Choose either "flsun_v400_STOCK.def.json" or "flsun_v400_updated_firmware.def.json" depending on if you have updated the stock firmware or not and RENAME TO flsun_v400.def.json!!! place the chosen file in the "definitions" directory in the configuration path.
8. Place the "flsun_v400. stl" file under the "meshes" directory in the configuration path.
9. Close all open CURA software and add V400 after opening it again.
V1.0.1 There are three nozzle sizes (0.25, 0.4, 0.6, and 0.8) to select from as well as under the 0.4 nozzle selection you have sub catagories of "default" "engineering" "visual" and "draft".
I also reworked the definition file for the V400 in order to remove the annoying yellow "warning" that occurs when you set print speed to 400
I have added testing modles for those that want to print with a standardized test print to help give feedback on these profiles.
Français:
1.sauvegardez et enregistrez une copie de vos fichiers V400 qui ont été chargés dans cura à partir de la clé USB FLSUN, puis supprimez ces fichiers de cura (ou commencez par une nouvelle installation)
2. Ouvrez cura et sélectionnez Aide-->Afficher le dossier de configuration
3. Placez le dossier "flsun_v400_extruder" dans le répertoire "extruders" sous le chemin de configuration cura.
4. Placez le dossier "flsun_v400_intent" dans le répertoire "intent" sous le chemin de configuration cura.
5. Placez le dossier "flsun_v400_quality" dans le répertoire "quality" sous le chemin de configuration cura.
6. Placez le dossier "flsun_v400_variants" dans le répertoire "variants" sous le chemin de configuration cura. (REMARQUE : copiez uniquement les tailles de buses que vous souhaitez utiliser si vous ne souhaitez pas que toutes les tailles de buses soient affichées)
7. Choisissez "flsun_v400_STOCK.def.json" ou "flsun_v400_updated_firmware.def.json" selon si vous avez mis à jour le firmware d'origine ou non et RENOMMER EN flsun_v400.def.json !!! placer le fichier choisi dans le répertoire "definitions" du chemin de configuration.
8. Placez le fichier "flsun_v400. stl" sous le répertoire "meshes" dans le chemin de configuration.
9. Fermez tous les logiciels CURA ouverts et ajoutez V400 après l'avoir rouvert.
V1.0.1 Il existe trois tailles de buses (0,25, 0,4, 0,6 et 0,8) parmi lesquelles choisir, ainsi que sous la sélection de buses 0,4, vous avez des sous-catégories de "par défaut" "ingénierie" "visuel" et "ébauche".
J'ai également retravaillé le fichier de définition pour le V400 afin de supprimer "l'avertissement" jaune gênant qui se produit lorsque vous réglez la vitesse d'impression sur 400
J'ai ajouté des modèles de test pour ceux qui souhaitent imprimer avec un test d'impression standardisé pour aider à donner leur avis sur ces profils.
Deutsch:
1. Sichern und speichern Sie eine Kopie Ihrer V400-Dateien, die vom FLSUN-Stick in Cura geladen wurden, und entfernen Sie diese Dateien dann aus Cura (oder beginnen Sie mit einer Neuinstallation).
2. Öffnen Sie Cura und wählen Sie Hilfe-->Konfigurationsordner anzeigen
3. Platzieren Sie den Ordner „flsun_v400_extruder“ im Verzeichnis „extruders“ unter dem Cura-Konfigurationspfad.
4. Platzieren Sie den Ordner „flsun_v400_intent“ im Verzeichnis „intent“ unter dem Cura-Konfigurationspfad.
5. Platzieren Sie den Ordner „flsun_v400_quality“ im Verzeichnis „quality“ unter dem Cura-Konfigurationspfad.
6. Platzieren Sie den Ordner „flsun_v400_variants“ im Verzeichnis „variants“ unter dem Cura-Konfigurationspfad. (HINWEIS: Kopieren Sie nur die Düsengrößen, die Sie verwenden möchten, wenn Sie nicht möchten, dass alle Düsengrößen angezeigt werden.)
7. Wählen Sie entweder „flsun_v400_STOCK.def.json“ oder „flsun_v400_updated_firmware.def.json“, je nachdem, ob Sie die Stock-Firmware aktualisiert haben oder nicht, und RENAME TO flsun_v400.def.json!!! Platzieren Sie die ausgewählte Datei im Verzeichnis "definitions" im Konfigurationspfad.
8. Platzieren Sie die Datei „flsun_v400.stl“ im Verzeichnis „meshes“ im Konfigurationspfad.
9. Schließen Sie alle geöffnete CURA-Software und fügen Sie V400 nach dem erneuten Öffnen hinzu.
V1.0.1 Es stehen drei Düsengrößen (0,25, 0,4, 0,6 und 0,8) zur Auswahl, außerdem gibt es unter der 0,4-Düsenauswahl Unterkategorien von „Standard“, „Technik“, „Visuell“ und „Entwurf“.
Ich habe auch die Definitionsdatei für den V400 überarbeitet, um die lästige gelbe "Warnung" zu entfernen, die auftritt, wenn Sie die Druckgeschwindigkeit auf 400 einstellen
Ich habe Testmodelle für diejenigen hinzugefügt, die mit einem standardisierten Testdruck drucken möchten, um Feedback zu diesen Profilen zu geben.