Releases: usbarmory/usbarmory-debian-base_image
USB armory Mk I - Debian base image release 20180222
This release contains the Debian base operating system image provided as reference for booting, and start developing on, the USB armory board.
The base image consists of a standard Linux distribution (Debian) prepared with the process outlined in the usbarmory-debian-base_image repository.
Installation
IMPORTANT: /dev/sdX, /dev/diskN must be replaced with your microSD device (not eventual microSD partitions), ensure that you are specifying the correct one. Errors in target specification will result in disk corruption.
NOTE: Remember to uncompress the downloaded image file before imaging.
Linux (verify target from terminal using dmesg):
sudo dd if=usbarmory-debian_stretch-base_image-20180222.raw of=/dev/sdX bs=1M conv=fsync
Mac OS X (verify target from terminal with diskutil list):
sudo dd if=usbarmory-debian_stretch-base_image-20180222.raw of=/dev/rdiskN bs=1m
On Windows, and other OSes, alternatively the Etcher utility can be used.
Connecting
After being booted, the image uses Ethernet over USB emulation (CDC Ethernet) to communicate with the host, with assigned IP address 10.0.0.1 (using 10.0.0.2 as gateway). Connection can be accomplished via SSH to 10.0.0.1, with default user usbarmory and password usbarmory. NOTE: There is a DHCP server running by default. Alternatively the host interface IP address can be statically set to 10.0.0.2/24.
LED feedback
To aid initial testing the base image configures the board LED to reflect CPU load average, via the Linux Heartbeat Trigger driver. In case this is undesired, the heartbeat can be disabled by removing the ledtrig_heartbeat module in /etc/modules. More information about LED control here.
Resizing
The default image is 4GB of size, to use the full microSD space a new partition can be added or the existing one can be resized as described here.
Additional resources
Project page
Documentation
Board schematics, layout and support files
INTERLOCK - file encryption front end
Discussion group
Major changes against the previous release:
- upgraded to kernel 4.14.20
- kernel installed as debian package
- added debian kernel repository (inversepath.github.io/debian) to allow kernel updates via apt-get
SHA256:
58afbdb1b1d6724bf53d929e32865cae8bbffb493137e5317dbe62e7fed6baa1 usbarmory-debian_stretch-base_image-20180222.raw.xz
4c1b7a6f714c110cd3bc03a1f80889ddab93d37227c14504ecc9bbf4f6ee676f usbarmory-debian_stretch-base_image-20180222.raw.zip
USB armory Mk I - Debian base image release 20180208
This release contains the Debian base operating system image provided as reference for booting, and start developing on, the USB armory board.
The base image consists of a standard Linux distribution (Debian) prepared with the process outlined in the usbarmory-debian-base_image repository.
Installation
IMPORTANT: /dev/sdX, /dev/diskN must be replaced with your microSD device (not eventual microSD partitions), ensure that you are specifying the correct one. Errors in target specification will result in disk corruption.
NOTE: Remember to uncompress the downloaded image file before imaging.
Linux (verify target from terminal using dmesg):
sudo dd if=usbarmory-debian_stretch-base_image-20180208.raw of=/dev/sdX bs=1M conv=fsync
Mac OS X (verify target from terminal with diskutil list):
sudo dd if=usbarmory-debian_stretch-base_image-20180208.raw of=/dev/rdiskN bs=1m
On Windows, and other OSes, alternatively the Etcher utility can be used.
Connecting
After being booted, the image uses Ethernet over USB emulation (CDC Ethernet) to communicate with the host, with assigned IP address 10.0.0.1 (using 10.0.0.2 as gateway). Connection can be accomplished via SSH to 10.0.0.1, with default user usbarmory and password usbarmory. NOTE: There is a DHCP server running by default. Alternatively the host interface IP address can be statically set to 10.0.0.2/24.
LED feedback
To aid initial testing the base image configures the board LED to reflect CPU load average, via the Linux Heartbeat Trigger driver. In case this is undesired, the heartbeat can be disabled by removing the ledtrig_heartbeat module in /etc/modules. More information about LED control here.
Resizing
The default image is 4GB of size, to use the full microSD space a new partition can be added or the existing one can be resized as described here.
Additional resources
Project page
Documentation
Board schematics, layout and support files
INTERLOCK - file encryption front end
Discussion group
Major changes against the previous release:
- upgraded to kernel 4.9.80
- fixed URLs in sources.list (#7)
SHA256:
28297c48157ede344777dc50fa3d7ce6885b976bb2d46bb786ceaa482adf40c5 usbarmory-debian_stretch-base_image-20180208.raw.xz
60f56112649b030fb5e8a213382f64d5629ca56c25ab3102bd8f6ee913c05d1f usbarmory-debian_stretch-base_image-20180208.raw.zip
USB armory Mk I - Debian base image release 20180115
This release contains the Debian base operating system image provided as reference for booting, and start developing on, the USB armory board.
The base image consists of a standard Linux distribution (Debian) prepared with the process outlined in the usbarmory-debian-base_image repository.
Installation
IMPORTANT: /dev/sdX, /dev/diskN must be replaced with your microSD device (not eventual microSD partitions), ensure that you are specifying the correct one. Errors in target specification will result in disk corruption.
NOTE: Remember to uncompress the downloaded image file before imaging.
Linux (verify target from terminal using dmesg):
sudo dd if=usbarmory-debian_stretch-base_image-20180115.raw of=/dev/sdX bs=1M conv=fsync
Mac OS X (verify target from terminal with diskutil list):
sudo dd if=usbarmory-debian_stretch-base_image-20180115.raw of=/dev/rdiskN bs=1m
On Windows, and other OSes, alternatively the Etcher utility can be used.
Connecting
After being booted, the image uses Ethernet over USB emulation (CDC Ethernet) to communicate with the host, with assigned IP address 10.0.0.1 (using 10.0.0.2 as gateway). Connection can be accomplished via SSH to 10.0.0.1, with default user usbarmory and password usbarmory. NOTE: There is a DHCP server running by default. Alternatively the host interface IP address can be statically set to 10.0.0.2/24.
LED feedback
To aid initial testing the base image configures the board LED to reflect CPU load average, via the Linux Heartbeat Trigger driver. In case this is undesired, the heartbeat can be disabled by removing the ledtrig_heartbeat module in /etc/modules. More information about LED control here.
Resizing
The default image is 4GB of size, to use the full microSD space a new partition can be added or the existing one can be resized as described here.
Additional resources
Project page
Documentation
Board schematics, layout and support files
INTERLOCK - file encryption front end
Discussion group
Major changes against the previous release:
- upgraded to kernel 4.9.75
- upgraded to Debian 9 (Stretch)
SHA256:
3ceda5f7b2eaadb226a9ef029a2f1eaa49c726d2b7e3c9674ed5d29084c4ec4d usbarmory-debian_stretch-base_image-20180115.raw.xz
fe814d67d9d7be028e537c72f73e727fa77c7d7c956690adbf8eb38e9652475a usbarmory-debian_stretch-base_image-20180115.raw.zip
USB armory Mk I - Debian base image release 20170518
This release contains the Debian base operating system image provided as reference for booting, and start developing on, the USB armory board.
The base image consists of a standard Linux distribution (Debian) prepared with the process outlined in the usbarmory-debian-base_image repository.
Installation
IMPORTANT: /dev/sdX, /dev/diskN must be replaced with your microSD device (not eventual microSD partitions), ensure that you are specifying the correct one. Errors in target specification will result in disk corruption.
NOTE: Remember to uncompress the downloaded image file before imaging.
Linux (verify target from terminal using dmesg):
sudo dd if=usbarmory-debian_jessie-base_image-20170518.raw of=/dev/sdX bs=1M conv=fsync
Mac OS X (verify target from terminal with diskutil list):
sudo dd if=usbarmory-debian_jessie-base_image-20170518.raw of=/dev/rdiskN bs=1m
On Windows, and other OSes, alternatively the Etcher utility can be used.
Connecting
After being booted, the image uses Ethernet over USB emulation (CDC Ethernet) to communicate with the host, with assigned IP address 10.0.0.1 (using 10.0.0.2 as gateway). Connection can be accomplished via SSH to 10.0.0.1, with default user usbarmory and password usbarmory. NOTE: There is a DHCP server running by default. Alternatively the host interface IP address can be statically set to 10.0.0.2/24.
LED feedback
To aid initial testing the base image configures the board LED to reflect CPU load average, via the Linux Heartbeat Trigger driver. In case this is undesired, the heartbeat can be disabled by removing the ledtrig_heartbeat module in /etc/modules. More information about LED control here.
Resizing
The default image is 4GB of size, to use the full microSD space a new partition can be added or the existing one can be resized as described here.
Additional resources
Project page
Documentation
Board schematics, layout and support files
INTERLOCK - file encryption front end
Discussion group
Major changes against the previous release:
- upgraded to kernel 4.9.28
- upgraded to U-Boot 2017.05
- enabled DHCP server
- added
/boot/imx53-usbarmory-scc2.dtbfor SCCv2 support
SHA256:
22eec0739b78b35fff99221d5abcfa06422b573eca4632a6f0cd9ba951654c11 usbarmory-debian_jessie-base_image-20170518.raw.xz
5225941826291068fe9df07ce8ec9237925db72cfe79f07a41818086392115f1 usbarmory-debian_jessie-base_image-20170518.raw.zip