-
Notifications
You must be signed in to change notification settings - Fork 1
/
Copy pathAdaptive_Mesh.cfg.txt
139 lines (109 loc) · 8.38 KB
/
Adaptive_Mesh.cfg.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
# # # Klipper Adaptive Meshing # # #
# Heads up! If you have any other BED_MESH_CALIBRATE macros defined elsewhere in your config, you will need to comment out / remove them for this to work. (Klicky/Euclid Probe)
# You will also need to be sure that [exclude_object] is defined in printer.cfg, and your slicer is labeling objects.
# This macro will parse information from objects in your gcode to define a min and max mesh area to probe, creating an adaptive mesh!
# This macro will not increase probe_count values in your [bed_mesh] config. If you want richer meshes, be sure to increase probe_count. We recommend at least 5,5.
[gcode_macro BED_MESH_CALIBRATE]
rename_existing: _BED_MESH_CALIBRATE
### This section allows control of status LEDs your printer may have.
variable_led_enable: False # Enables/disables the use of status LEDs in this macro.
variable_status_macro: 'status_meshing' # If you have status LEDs in your printer (StealthBurner), you can use the macro that changes their status here.
### This section configures mesh point fuzzing, which allows probe points to be varied slightly if printing multiples of the same G-code file.
variable_fuzz_enable: False # Enables/disables the use of mesh point fuzzing to slightly randomize probing points to spread out wear on a build surface, default is False.
variable_fuzz_min: 0 # If enabled, the minimum amount in mm a probe point can be randomized, default is 0.
variable_fuzz_max: 4 # If enabled, the maximum amount in mm a probe point can be randomized, default is 4.
### This section is for configuring a mesh margin, which allows the probed mesh to be expanded outwards from the print area.
variable_margin_enable: False # Enables/disables adding a margin to the meshed area to pad a mesh out for specific needs, default is False.
variable_margin_size: 5 # Size in millimeters to expand the mesh outwards from the print area in all directions.
### This section is for those using a dockable probe that is stored outside of the print area. ###
variable_probe_dock_enable: False # Enables/disables the use of a dockable probe that is stored outside of the print area, default is False.
variable_attach_macro: 'Attach_Probe' # Here is where you define the macro that ATTACHES the probe to the printhead. E.g. 'Attach_Probe'
variable_detach_macro: 'Dock_Probe' # Here is where you define the macro that DETACHES the probe from the printhead. E.g. 'Dock_Probe'
### This section is for those who are using Moonraker's Update Manager for KAMP, or want a more verbose macro. ###
variable_display_parameters: True # Display macro paramters in the console, useful for debugging the SETUP_KAMP_MESHING call, or more verbosity.
gcode:
{% if display_parameters == True %}
{ action_respond_info("led_enable : %d" % (led_enable)) }
{ action_respond_info("status_macro: \'%s\'" % (status_macro)) }
{ action_respond_info("fuzz_enable : %d" % (fuzz_enable)) }
{ action_respond_info("fuzz_min : %f" % (fuzz_min)) }
{ action_respond_info("fuzz_max : %f" % (fuzz_max)) }
{ action_respond_info("probe_dock_enable: %d" % (probe_dock_enable)) }
{ action_respond_info("attach_macro: \'%s\'" % (attach_macro)) }
{ action_respond_info("detach_macro: \'%s\'" % (detach_macro)) }
{% endif %}
{% set all_points = printer.exclude_object.objects | map(attribute='polygon') | sum(start=[]) %}
{% set bed_mesh_min = printer.configfile.settings.bed_mesh.mesh_min %}
{% set bed_mesh_max = printer.configfile.settings.bed_mesh.mesh_max %}
{% set probe_count = printer.configfile.settings.bed_mesh.probe_count %}
{% set probe_count = probe_count if probe_count|length > 1 else probe_count * 2 %}
{% set max_probe_point_distance_x = ( bed_mesh_max[0] - bed_mesh_min[0] ) / (probe_count[0] - 1) %}
{% set max_probe_point_distance_y = ( bed_mesh_max[1] - bed_mesh_min[1] ) / (probe_count[1] - 1) %}
{% set x_min = all_points | map(attribute=0) | min | default(bed_mesh_min[0]) %}
{% set y_min = all_points | map(attribute=1) | min | default(bed_mesh_min[1]) %}
{% set x_max = all_points | map(attribute=0) | max | default(bed_mesh_max[0]) %}
{% set y_max = all_points | map(attribute=1) | max | default(bed_mesh_max[1]) %}
{% if margin_enable == False %}
{% set margin_size = 0 %}
{% endif %}
{ action_respond_info("{} object points, clamping to bed mesh [{!r} {!r}]".format(
all_points | count,
bed_mesh_min,
bed_mesh_max,
)) }
{% if fuzz_enable == True %}
{% set fuzz_range = range((fuzz_min * 100) | int, (fuzz_max * 100) | int + 1) %}
{% set x_min = (bed_mesh_min[0] + fuzz_max - margin_size, x_min) | max - (fuzz_range | random / 100.0) %}
{% set y_min = (bed_mesh_min[1] + fuzz_max - margin_size, y_min) | max - (fuzz_range | random / 100.0) %}
{% set x_max = (bed_mesh_max[0] - fuzz_max + margin_size, x_max) | min + (fuzz_range | random / 100.0) %}
{% set y_max = (bed_mesh_max[1] - fuzz_max + margin_size, y_max) | min + (fuzz_range | random / 100.0) %}
{% else %}
{% set x_min = [ bed_mesh_min[0], x_min - margin_size ] | max %}
{% set y_min = [ bed_mesh_min[1], y_min - margin_size ] | max %}
{% set x_max = [ bed_mesh_max[0], x_max + margin_size ] | min %}
{% set y_max = [ bed_mesh_max[1], y_max + margin_size ] | min %}
{% endif %}
{ action_respond_info("Object bounds, clamped to the bed_mesh: {!r}, {!r}".format(
(x_min, y_min),
(x_max, y_max),
)) }
{% set points_x = (((x_max - x_min) / max_probe_point_distance_x) | round(method='ceil') | int) + 1 %}
{% set points_y = (((y_max - y_min) / max_probe_point_distance_y) | round(method='ceil') | int) + 1 %}
{% if (([points_x, points_y]|max) > 6) %}
{% set algorithm = "bicubic" %}
{% set min_points = 4 %}
{% else %}
{% set algorithm = "lagrange" %}
{% set min_points = 3 %}
{% endif %}
{ action_respond_info( "Algorithm: {}".format(algorithm)) }
{% set points_x = [points_x, min_points]|max %}
{% set points_y = [points_y, min_points]|max %}
{ action_respond_info( "Points: x: {}, y: {}".format(points_x, points_y) ) }
{% if printer.configfile.settings.bed_mesh.relative_reference_index is defined %}
{% set ref_index = (points_x * points_y / 2) | int %}
{ action_respond_info( "Reference index: {}".format(ref_index) ) }
{% else %}
{% set ref_index = -1 %}
{% endif %}
{% if probe_dock_enable == True %}
{attach_macro} # Attach/deploy a probe if the probe is stored somewhere outside of the print area
{% endif %}
{% if led_enable == True %}
{status_macro} # Set status LEDs
{% endif %}
_BED_MESH_CALIBRATE mesh_min={x_min},{y_min} mesh_max={x_max},{y_max} ALGORITHM={algorithm} PROBE_COUNT={points_x},{points_y} RELATIVE_REFERENCE_INDEX={ref_index}
{% if probe_dock_enable == True %}
{detach_macro} # Detach/stow a probe if the probe is stored somewhere outside of the print area
{% endif %}
[gcode_macro SETUP_KAMP_MESHING]
gcode:
SET_GCODE_VARIABLE MACRO=BED_MESH_CALIBRATE VARIABLE=display_parameters VALUE={params.DISPLAY_PARAMETERS|default(True)|int}
SET_GCODE_VARIABLE MACRO=BED_MESH_CALIBRATE VARIABLE=led_enable VALUE={params.LED_ENABLE|default(False)|int}
SET_GCODE_VARIABLE MACRO=BED_MESH_CALIBRATE VARIABLE=status_macro VALUE='"{params.STATUS_MACRO|default('status_meshing')|string}"'
SET_GCODE_VARIABLE MACRO=BED_MESH_CALIBRATE VARIABLE=fuzz_enable VALUE={params.FUZZ_ENABLE|default(False)|int}
SET_GCODE_VARIABLE MACRO=BED_MESH_CALIBRATE VARIABLE=fuzz_min VALUE={params.FUZZ_MIN|default(0)|float}
SET_GCODE_VARIABLE MACRO=BED_MESH_CALIBRATE VARIABLE=fuzz_max VALUE={params.FUZZ_MAX|default(4)|float}
SET_GCODE_VARIABLE MACRO=BED_MESH_CALIBRATE VARIABLE=probe_dock_enable VALUE={params.PROBE_DOCK_ENABLE|default(False)|int}
SET_GCODE_VARIABLE MACRO=BED_MESH_CALIBRATE VARIABLE=attach_macro VALUE='"{params.ATTACH_MACRO|default('Attach_Probe')|string}"'
SET_GCODE_VARIABLE MACRO=BED_MESH_CALIBRATE VARIABLE=detach_macro VALUE='"{params.DETACH_MACRO|default('Dock_Probe')|string}"'