From cd512b24f7902b04e66bb2b8c6cca4f9b09eee82 Mon Sep 17 00:00:00 2001 From: r4ulcl Date: Wed, 3 Jul 2024 15:30:49 +0100 Subject: [PATCH] Fix WPA3 TKIP error --- APs/config/wpa3/hostapd_bruteforce.conf.tmp | 3067 +------------------ APs/config/wpa3/hostapd_downgrade.conf.tmp | 3062 +----------------- Attacker/installTools.sh | 8 +- 3 files changed, 12 insertions(+), 6125 deletions(-) diff --git a/APs/config/wpa3/hostapd_bruteforce.conf.tmp b/APs/config/wpa3/hostapd_bruteforce.conf.tmp index 5be2a85..85673de 100644 --- a/APs/config/wpa3/hostapd_bruteforce.conf.tmp +++ b/APs/config/wpa3/hostapd_bruteforce.conf.tmp @@ -1,3109 +1,56 @@ ##### hostapd configuration file ############################################## # Empty lines and lines starting with # are ignored -# AP netdevice name (without 'ap' postfix, i.e., wlan0 uses wlan0ap for -# management frames with the Host AP driver); wlan0 with many nl80211 drivers -# Note: This attribute can be overridden by the values supplied with the '-i' -# command line parameter. interface=$WLAN_BRUTEFORCE - -# In case of atheros and nl80211 driver interfaces, an additional -# configuration parameter, bridge, may be used to notify hostapd if the -# interface is included in a bridge. This parameter is not used with Host AP -# driver. If the bridge parameter is not set, the drivers will automatically -# figure out the bridge interface (assuming sysfs is enabled and mounted to -# /sys) and this parameter may not be needed. -# -# For nl80211, this parameter can be used to request the AP interface to be -# added to the bridge automatically (brctl may refuse to do this before hostapd -# has been started to change the interface mode). If needed, the bridge -# interface is also created. -#bridge=br0 - -# Driver interface type (hostap/wired/none/nl80211/bsd); -# default: hostap). nl80211 is used with all Linux mac80211 drivers. -# Use driver=none if building hostapd as a standalone RADIUS server that does -# not control any wireless/wired driver. -# driver=hostap - -# Driver interface parameters (mainly for development testing use) -# driver_params= - -# hostapd event logger configuration -# -# Two output method: syslog and stdout (only usable if not forking to -# background). -# -# Module bitfield (ORed bitfield of modules that will be logged; -1 = all -# modules): -# bit 0 (1) = IEEE 802.11 -# bit 1 (2) = IEEE 802.1X -# bit 2 (4) = RADIUS -# bit 3 (8) = WPA -# bit 4 (16) = driver interface -# bit 6 (64) = MLME -# -# Levels (minimum value for logged events): -# 0 = verbose debugging -# 1 = debugging -# 2 = informational messages -# 3 = notification -# 4 = warning -# logger_syslog=-1 logger_syslog_level=2 logger_stdout=-1 logger_stdout_level=2 - -# Interface for separate control program. If this is specified, hostapd -# will create this directory and a UNIX domain socket for listening to requests -# from external programs (CLI/GUI, etc.) for status information and -# configuration. The socket file will be named based on the interface name, so -# multiple hostapd processes/interfaces can be run at the same time if more -# than one interface is used. -# /var/run/hostapd is the recommended directory for sockets and by default, -# hostapd_cli will use it when trying to connect with hostapd. ctrl_interface=/var/run/hostapd - -# Access control for the control interface can be configured by setting the -# directory to allow only members of a group to use sockets. This way, it is -# possible to run hostapd as root (since it needs to change network -# configuration and open raw sockets) and still allow GUI/CLI components to be -# run as non-root users. However, since the control interface can be used to -# change the network configuration, this access needs to be protected in many -# cases. By default, hostapd is configured to use gid 0 (root). If you -# want to allow non-root users to use the control interface, add a new group -# and change this value to match with that group. Add users that should have -# control interface access to this group. -# -# This variable can be a group name or gid. -#ctrl_interface_group=wheel ctrl_interface_group=0 - - -##### IEEE 802.11 related configuration ####################################### - -# SSID to be used in IEEE 802.11 management frames -ssid=wifi-management -# Alternative formats for configuring SSID -# (double quoted string, hexdump, printf-escaped string) -#ssid2="test" -#ssid2=74657374 -#ssid2=P"hello\nthere" - -# UTF-8 SSID: Whether the SSID is to be interpreted using UTF-8 encoding -#utf8_ssid=1 - -# Country code (ISO/IEC 3166-1). Used to set regulatory domain. -# Set as needed to indicate country in which device is operating. -# This can limit available channels and transmit power. -# These two octets are used as the first two octets of the Country String -# (dot11CountryString) -#country_code=US - -# The third octet of the Country String (dot11CountryString) -# This parameter is used to set the third octet of the country string. -# -# All environments of the current frequency band and country (default) -#country3=0x20 -# Outdoor environment only -#country3=0x4f -# Indoor environment only -#country3=0x49 -# Noncountry entity (country_code=XX) -#country3=0x58 -# IEEE 802.11 standard Annex E table indication: 0x01 .. 0x1f -# Annex E, Table E-4 (Global operating classes) -#country3=0x04 - -# Enable IEEE 802.11d. This advertises the country_code and the set of allowed -# channels and transmit power levels based on the regulatory limits. The -# country_code setting must be configured with the correct country for -# IEEE 802.11d functions. -# (default: 0 = disabled) -#ieee80211d=1 - -# Enable IEEE 802.11h. This enables radar detection and DFS support if -# available. DFS support is required on outdoor 5 GHz channels in most countries -# of the world. This can be used only with ieee80211d=1. -# (default: 0 = disabled) -#ieee80211h=1 - -# Add Power Constraint element to Beacon and Probe Response frames -# This config option adds Power Constraint element when applicable and Country -# element is added. Power Constraint element is required by Transmit Power -# Control. This can be used only with ieee80211d=1. -# Valid values are 0..255. -#local_pwr_constraint=3 - -# Set Spectrum Management subfield in the Capability Information field. -# This config option forces the Spectrum Management bit to be set. When this -# option is not set, the value of the Spectrum Management bit depends on whether -# DFS or TPC is required by regulatory authorities. This can be used only with -# ieee80211d=1 and local_pwr_constraint configured. -#spectrum_mgmt_required=1 - -# Operation mode (a = IEEE 802.11a (5 GHz), b = IEEE 802.11b (2.4 GHz), -# g = IEEE 802.11g (2.4 GHz), ad = IEEE 802.11ad (60 GHz); a/g options are used -# with IEEE 802.11n (HT), too, to specify band). For IEEE 802.11ac (VHT), this -# needs to be set to hw_mode=a. For IEEE 802.11ax (HE) on 6 GHz this needs -# to be set to hw_mode=a. When using ACS (see channel parameter), a -# special value "any" can be used to indicate that any support band can be used. -# This special case is currently supported only with drivers with which -# offloaded ACS is used. -# Default: IEEE 802.11b +ssid=wifi-c hw_mode=g - -# Channel number (IEEE 802.11) -# (default: 0, i.e., not set) -# Please note that some drivers do not use this value from hostapd and the -# channel will need to be configured separately with iwconfig. -# -# If CONFIG_ACS build option is enabled, the channel can be selected -# automatically at run time by setting channel=acs_survey or channel=0, both of -# which will enable the ACS survey based algorithm. channel=11 - -# Global operating class (IEEE 802.11, Annex E, Table E-4) -# This option allows hostapd to specify the operating class of the channel -# configured with the channel parameter. channel and op_class together can -# uniquely identify channels across different bands, including the 6 GHz band. -#op_class=131 - -# ACS tuning - Automatic Channel Selection -# See: https://wireless.wiki.kernel.org/en/users/documentation/acs -# -# You can customize the ACS survey algorithm with following variables: -# -# acs_num_scans requirement is 1..100 - number of scans to be performed that -# are used to trigger survey data gathering of an underlying device driver. -# Scans are passive and typically take a little over 100ms (depending on the -# driver) on each available channel for given hw_mode. Increasing this value -# means sacrificing startup time and gathering more data wrt channel -# interference that may help choosing a better channel. This can also help fine -# tune the ACS scan time in case a driver has different scan dwell times. -# -# acs_chan_bias is a space-separated list of : pairs. It can be -# used to increase (or decrease) the likelihood of a specific channel to be -# selected by the ACS algorithm. The total interference factor for each channel -# gets multiplied by the specified bias value before finding the channel with -# the lowest value. In other words, values between 0.0 and 1.0 can be used to -# make a channel more likely to be picked while values larger than 1.0 make the -# specified channel less likely to be picked. This can be used, e.g., to prefer -# the commonly used 2.4 GHz band channels 1, 6, and 11 (which is the default -# behavior on 2.4 GHz band if no acs_chan_bias parameter is specified). -# -# Defaults: -#acs_num_scans=5 -#acs_chan_bias=1:0.8 6:0.8 11:0.8 - -# Channel list restriction. This option allows hostapd to select one of the -# provided channels when a channel should be automatically selected. -# Channel list can be provided as range using hyphen ('-') or individual -# channels can be specified by space (' ') separated values -# Default: all channels allowed in selected hw_mode -#chanlist=100 104 108 112 116 -#chanlist=1 6 11-13 - -# Frequency list restriction. This option allows hostapd to select one of the -# provided frequencies when a frequency should be automatically selected. -# Frequency list can be provided as range using hyphen ('-') or individual -# frequencies can be specified by comma (',') separated values -# Default: all frequencies allowed in selected hw_mode -#freqlist=2437,5955,5975 -#freqlist=2437,5985-6105 - -# Exclude DFS channels from ACS -# This option can be used to exclude all DFS channels from the ACS channel list -# in cases where the driver supports DFS channels. -#acs_exclude_dfs=1 - -# Include only preferred scan channels from 6 GHz band for ACS -# This option can be used to include only preferred scan channels in the 6 GHz -# band. This can be useful in particular for devices that operate only a 6 GHz -# BSS without a collocated 2.4/5 GHz BSS. -# Default behavior is to include all PSC and non-PSC channels. -#acs_exclude_6ghz_non_psc=1 - -# Enable background radar feature -# This feature allows CAC to be run on dedicated radio RF chains while the -# radio(s) are otherwise running normal AP activities on other channels. -# This requires that the driver and the radio support it before feature will -# actually be enabled, i.e., this parameter value is ignored with drivers that -# do not advertise support for the capability. -# 0: Leave disabled (default) -# 1: Enable it. -#enable_background_radar=1 - -# Set minimum permitted max TX power (in dBm) for ACS and DFS channel selection. -# (default 0, i.e., not constraint) -#min_tx_power=20 - -# Beacon interval in kus (1.024 ms) (default: 100; range 15..65535) beacon_int=100 - -# DTIM (delivery traffic information message) period (range 1..255): -# number of beacons between DTIMs (1 = every beacon includes DTIM element) -# (default: 2) dtim_period=2 - -# Maximum number of stations allowed in station table. New stations will be -# rejected after the station table is full. IEEE 802.11 has a limit of 2007 -# different association IDs, so this number should not be larger than that. -# (default: 2007) max_num_sta=255 - -# RTS/CTS threshold; -1 = disabled (default); range -1..65535 -# If this field is not included in hostapd.conf, hostapd will not control -# RTS threshold and 'iwconfig wlan# rts ' can be used to set it. rts_threshold=-1 - -# Fragmentation threshold; -1 = disabled (default); range -1, 256..2346 -# If this field is not included in hostapd.conf, hostapd will not control -# fragmentation threshold and 'iwconfig wlan# frag ' can be used to set -# it. fragm_threshold=-1 - -# Rate configuration -# Default is to enable all rates supported by the hardware. This configuration -# item allows this list be filtered so that only the listed rates will be left -# in the list. If the list is empty, all rates are used. This list can have -# entries that are not in the list of rates the hardware supports (such entries -# are ignored). The entries in this list are in 100 kbps, i.e., 11 Mbps = 110. -# If this item is present, at least one rate have to be matching with the rates -# hardware supports. -# default: use the most common supported rate setting for the selected -# hw_mode (i.e., this line can be removed from configuration file in most -# cases) -#supported_rates=10 20 55 110 60 90 120 180 240 360 480 540 - -# Basic rate set configuration -# List of rates (in 100 kbps) that are included in the basic rate set. -# If this item is not included, usually reasonable default set is used. -#basic_rates=10 20 -#basic_rates=10 20 55 110 -#basic_rates=60 120 240 - -# Beacon frame TX rate configuration -# This sets the TX rate that is used to transmit Beacon frames. If this item is -# not included, the driver default rate (likely lowest rate) is used. -# Legacy (CCK/OFDM rates): -# beacon_rate= -# HT: -# beacon_rate=ht: -# VHT: -# beacon_rate=vht: -# HE: -# beacon_rate=he: -# -# For example, beacon_rate=10 for 1 Mbps or beacon_rate=60 for 6 Mbps (OFDM). -#beacon_rate=10 - -# Short Preamble -# This parameter can be used to enable optional use of short preamble for -# frames sent at 2 Mbps, 5.5 Mbps, and 11 Mbps to improve network performance. -# This applies only to IEEE 802.11b-compatible networks and this should only be -# enabled if the local hardware supports use of short preamble. If any of the -# associated STAs do not support short preamble, use of short preamble will be -# disabled (and enabled when such STAs disassociate) dynamically. -# 0 = do not allow use of short preamble (default) -# 1 = allow use of short preamble -#preamble=1 - -# Station MAC address -based authentication -# Please note that this kind of access control requires a driver that uses -# hostapd to take care of management frame processing and as such, this can be -# used with driver=hostap or driver=nl80211, but not with driver=atheros. -# 0 = accept unless in deny list -# 1 = deny unless in accept list -# 2 = use external RADIUS server (accept/deny lists are searched first) macaddr_acl=0 - -# Accept/deny lists are read from separate files (containing list of -# MAC addresses, one per line). Use absolute path name to make sure that the -# files can be read on SIGHUP configuration reloads. -#accept_mac_file=/etc/hostapd.accept -#deny_mac_file=/etc/hostapd.deny - -# IEEE 802.11 specifies two authentication algorithms. hostapd can be -# configured to allow both of these or only one. Open system authentication -# should be used with IEEE 802.1X. -# Bit fields of allowed authentication algorithms: -# bit 0 = Open System Authentication -# bit 1 = Shared Key Authentication (requires WEP) -auth_algs=3 - -# Send empty SSID in beacons and ignore probe request frames that do not -# specify full SSID, i.e., require stations to know SSID. -# default: disabled (0) -# 1 = send empty (length=0) SSID in beacon and ignore probe request for -# broadcast SSID -# 2 = clear SSID (ASCII 0), but keep the original length (this may be required -# with some clients that do not support empty SSID) and ignore probe -# requests for broadcast SSID +auth_algs=1 ignore_broadcast_ssid=0 - -# Do not reply to broadcast Probe Request frames from unassociated STA if there -# is no room for additional stations (max_num_sta). This can be used to -# discourage a STA from trying to associate with this AP if the association -# would be rejected due to maximum STA limit. -# Default: 0 (disabled) -#no_probe_resp_if_max_sta=0 - -# Additional vendor specific elements for Beacon and Probe Response frames -# This parameter can be used to add additional vendor specific element(s) into -# the end of the Beacon and Probe Response frames. The format for these -# element(s) is a hexdump of the raw information elements (id+len+payload for -# one or more elements) -#vendor_elements=dd0411223301 - -# Additional vendor specific elements for (Re)Association Response frames -# This parameter can be used to add additional vendor specific element(s) into -# the end of the (Re)Association Response frames. The format for these -# element(s) is a hexdump of the raw information elements (id+len+payload for -# one or more elements) -#assocresp_elements=dd0411223301 - -# TX queue parameters (EDCF / bursting) -# tx_queue__ -# queues: data0, data1, data2, data3 -# (data0 is the highest priority queue) -# parameters: -# aifs: AIFS (default 2) -# cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023, 2047, 4095, 8191, -# 16383, 32767) -# cwmax: cwMax (same values as cwMin, cwMax >= cwMin) -# burst: maximum length (in milliseconds with precision of up to 0.1 ms) for -# bursting -# -# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): -# These parameters are used by the access point when transmitting frames -# to the clients. -# -# Low priority / AC_BK = background -#tx_queue_data3_aifs=7 -#tx_queue_data3_cwmin=15 -#tx_queue_data3_cwmax=1023 -#tx_queue_data3_burst=0 -# Note: for IEEE 802.11b mode: cWmin=31 cWmax=1023 burst=0 -# -# Normal priority / AC_BE = best effort -#tx_queue_data2_aifs=3 -#tx_queue_data2_cwmin=15 -#tx_queue_data2_cwmax=63 -#tx_queue_data2_burst=0 -# Note: for IEEE 802.11b mode: cWmin=31 cWmax=127 burst=0 -# -# High priority / AC_VI = video -#tx_queue_data1_aifs=1 -#tx_queue_data1_cwmin=7 -#tx_queue_data1_cwmax=15 -#tx_queue_data1_burst=3.0 -# Note: for IEEE 802.11b mode: cWmin=15 cWmax=31 burst=6.0 -# -# Highest priority / AC_VO = voice -#tx_queue_data0_aifs=1 -#tx_queue_data0_cwmin=3 -#tx_queue_data0_cwmax=7 -#tx_queue_data0_burst=1.5 -# Note: for IEEE 802.11b mode: cWmin=7 cWmax=15 burst=3.3 - -# 802.1D Tag (= UP) to AC mappings -# WMM specifies following mapping of data frames to different ACs. This mapping -# can be configured using Linux QoS/tc and sch_pktpri.o module. -# 802.1D Tag 802.1D Designation Access Category WMM Designation -# 1 BK AC_BK Background -# 2 - AC_BK Background -# 0 BE AC_BE Best Effort -# 3 EE AC_BE Best Effort -# 4 CL AC_VI Video -# 5 VI AC_VI Video -# 6 VO AC_VO Voice -# 7 NC AC_VO Voice -# Data frames with no priority information: AC_BE -# Management frames: AC_VO -# PS-Poll frames: AC_BE - -# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): -# for 802.11a or 802.11g networks -# These parameters are sent to WMM clients when they associate. -# The parameters will be used by WMM clients for frames transmitted to the -# access point. -# -# note - txop_limit is in units of 32microseconds -# note - acm is admission control mandatory flag. 0 = admission control not -# required, 1 = mandatory -# note - Here cwMin and cmMax are in exponent form. The actual cw value used -# will be (2^n)-1 where n is the value given here. The allowed range for these -# wmm_ac_??_{cwmin,cwmax} is 0..15 with cwmax >= cwmin. -# wmm_enabled=1 -# -# WMM-PS Unscheduled Automatic Power Save Delivery [U-APSD] -# Enable this flag if U-APSD supported outside hostapd (eg., Firmware/driver) -#uapsd_advertisement_enabled=1 -# -# Low priority / AC_BK = background wmm_ac_bk_cwmin=4 wmm_ac_bk_cwmax=10 wmm_ac_bk_aifs=7 wmm_ac_bk_txop_limit=0 wmm_ac_bk_acm=0 -# Note: for IEEE 802.11b mode: cWmin=5 cWmax=10 -# -# Normal priority / AC_BE = best effort wmm_ac_be_aifs=3 wmm_ac_be_cwmin=4 wmm_ac_be_cwmax=10 wmm_ac_be_txop_limit=0 wmm_ac_be_acm=0 -# Note: for IEEE 802.11b mode: cWmin=5 cWmax=7 -# -# High priority / AC_VI = video wmm_ac_vi_aifs=2 wmm_ac_vi_cwmin=3 wmm_ac_vi_cwmax=4 wmm_ac_vi_txop_limit=94 wmm_ac_vi_acm=0 -# Note: for IEEE 802.11b mode: cWmin=4 cWmax=5 txop_limit=188 -# -# Highest priority / AC_VO = voice wmm_ac_vo_aifs=2 wmm_ac_vo_cwmin=2 wmm_ac_vo_cwmax=3 wmm_ac_vo_txop_limit=47 wmm_ac_vo_acm=0 -# Note: for IEEE 802.11b mode: cWmin=3 cWmax=4 burst=102 - -# Enable Multi-AP functionality -# 0 = disabled (default) -# 1 = AP support backhaul BSS -# 2 = AP support fronthaul BSS -# 3 = AP supports both backhaul BSS and fronthaul BSS -#multi_ap=0 - -# Static WEP key configuration -# -# The key number to use when transmitting. -# It must be between 0 and 3, and the corresponding key must be set. -# default: not set -#wep_default_key=0 -# The WEP keys to use. -# A key may be a quoted string or unquoted hexadecimal digits. -# The key length should be 5, 13, or 16 characters, or 10, 26, or 32 -# digits, depending on whether 40-bit (64-bit), 104-bit (128-bit), or -# 128-bit (152-bit) WEP is used. -# Only the default key must be supplied; the others are optional. -# default: not set -#wep_key0=123456789a -#wep_key1="vwxyz" -#wep_key2=0102030405060708090a0b0c0d -#wep_key3=".2.4.6.8.0.23" - -# Station inactivity limit -# -# If a station does not send anything in ap_max_inactivity seconds, an -# empty data frame is sent to it in order to verify whether it is -# still in range. If this frame is not ACKed, the station will be -# disassociated and then deauthenticated. This feature is used to -# clear station table of old entries when the STAs move out of the -# range. -# -# The station can associate again with the AP if it is still in range; -# this inactivity poll is just used as a nicer way of verifying -# inactivity; i.e., client will not report broken connection because -# disassociation frame is not sent immediately without first polling -# the STA with a data frame. -# default: 300 (i.e., 5 minutes) -#ap_max_inactivity=300 -# -# The inactivity polling can be disabled to disconnect stations based on -# inactivity timeout so that idle stations are more likely to be disconnected -# even if they are still in range of the AP. This can be done by setting -# skip_inactivity_poll to 1 (default 0). -#skip_inactivity_poll=0 - -# Disassociate stations based on excessive transmission failures or other -# indications of connection loss. This depends on the driver capabilities and -# may not be available with all drivers. -#disassoc_low_ack=1 - -# Maximum allowed Listen Interval (how many Beacon periods STAs are allowed to -# remain asleep). Default: 65535 (no limit apart from field size) -#max_listen_interval=100 - -# WDS (4-address frame) mode with per-station virtual interfaces -# (only supported with driver=nl80211) -# This mode allows associated stations to use 4-address frames to allow layer 2 -# bridging to be used. -#wds_sta=1 - -# If bridge parameter is set, the WDS STA interface will be added to the same -# bridge by default. This can be overridden with the wds_bridge parameter to -# use a separate bridge. -#wds_bridge=wds-br0 - -# Start the AP with beaconing disabled by default. -#start_disabled=0 - -# Client isolation can be used to prevent low-level bridging of frames between -# associated stations in the BSS. By default, this bridging is allowed. -#ap_isolate=1 - -# BSS Load update period (in BUs) -# This field is used to enable and configure adding a BSS Load element into -# Beacon and Probe Response frames. -#bss_load_update_period=50 - -# Channel utilization averaging period (in BUs) -# This field is used to enable and configure channel utilization average -# calculation with bss_load_update_period. This should be in multiples of -# bss_load_update_period for more accurate calculation. -#chan_util_avg_period=600 - -# Fixed BSS Load value for testing purposes -# This field can be used to configure hostapd to add a fixed BSS Load element -# into Beacon and Probe Response frames for testing purposes. The format is -# :: -#bss_load_test=12:80:20000 - -# Multicast to unicast conversion -# Request that the AP will do multicast-to-unicast conversion for ARP, IPv4, and -# IPv6 frames (possibly within 802.1Q). If enabled, such frames are to be sent -# to each station separately, with the DA replaced by their own MAC address -# rather than the group address. -# -# Note that this may break certain expectations of the receiver, such as the -# ability to drop unicast IP packets received within multicast L2 frames, or the -# ability to not send ICMP destination unreachable messages for packets received -# in L2 multicast (which is required, but the receiver can't tell the difference -# if this new option is enabled). -# -# This also doesn't implement the 802.11 DMS (directed multicast service). -# -#multicast_to_unicast=0 - -# Send broadcast Deauthentication frame on AP start/stop -# Default: 1 (enabled) -#broadcast_deauth=1 - -# Get notifications for received Management frames on control interface -# Default: 0 (disabled) -#notify_mgmt_frames=0 - -##### IEEE 802.11n related configuration ###################################### - -# ieee80211n: Whether IEEE 802.11n (HT) is enabled -# 0 = disabled (default) -# 1 = enabled -# Note: You will also need to enable WMM for full HT functionality. -# Note: hw_mode=g (2.4 GHz) and hw_mode=a (5 GHz) is used to specify the band. -#ieee80211n=1 - -# disable_11n: Boolean (0/1) to disable HT for a specific BSS -#disable_11n=0 - -# ht_capab: HT capabilities (list of flags) -# LDPC coding capability: [LDPC] = supported -# Supported channel width set: [HT40-] = both 20 MHz and 40 MHz with secondary -# channel below the primary channel; [HT40+] = both 20 MHz and 40 MHz -# with secondary channel above the primary channel -# (20 MHz only if neither is set) -# Note: There are limits on which channels can be used with HT40- and -# HT40+. Following table shows the channels that may be available for -# HT40- and HT40+ use per IEEE 802.11n Annex J: -# freq HT40- HT40+ -# 2.4 GHz 5-13 1-7 (1-9 in Europe/Japan) -# 5 GHz 40,48,56,64 36,44,52,60 -# (depending on the location, not all of these channels may be available -# for use) -# Please note that 40 MHz channels may switch their primary and secondary -# channels if needed or creation of 40 MHz channel maybe rejected based -# on overlapping BSSes. These changes are done automatically when hostapd -# is setting up the 40 MHz channel. -# HT-greenfield: [GF] (disabled if not set) -# Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set) -# Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set) -# Tx STBC: [TX-STBC] (disabled if not set) -# Rx STBC: [RX-STBC1] (one spatial stream), [RX-STBC12] (one or two spatial -# streams), or [RX-STBC123] (one, two, or three spatial streams); Rx STBC -# disabled if none of these set -# HT-delayed Block Ack: [DELAYED-BA] (disabled if not set) -# Maximum A-MSDU length: [MAX-AMSDU-7935] for 7935 octets (3839 octets if not -# set) -# DSSS/CCK Mode in 40 MHz: [DSSS_CCK-40] = allowed (not allowed if not set) -# 40 MHz intolerant [40-INTOLERANT] (not advertised if not set) -# L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set) -#ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40] - -# Require stations to support HT PHY (reject association if they do not) -#require_ht=1 - -# If set non-zero, require stations to perform scans of overlapping -# channels to test for stations which would be affected by 40 MHz traffic. -# This parameter sets the interval in seconds between these scans. Setting this -# to non-zero allows 2.4 GHz band AP to move dynamically to a 40 MHz channel if -# no co-existence issues with neighboring devices are found. -#obss_interval=0 - -##### IEEE 802.11ac related configuration ##################################### - -# ieee80211ac: Whether IEEE 802.11ac (VHT) is enabled -# 0 = disabled (default) -# 1 = enabled -# Note: You will also need to enable WMM for full VHT functionality. -# Note: hw_mode=a is used to specify that 5 GHz band is used with VHT. -#ieee80211ac=1 - -# disable_11ac: Boolean (0/1) to disable VHT for a specific BSS -#disable_11ac=0 - -# vht_capab: VHT capabilities (list of flags) -# -# vht_max_mpdu_len: [MAX-MPDU-7991] [MAX-MPDU-11454] -# Indicates maximum MPDU length -# 0 = 3895 octets (default) -# 1 = 7991 octets -# 2 = 11454 octets -# 3 = reserved -# -# supported_chan_width: [VHT160] [VHT160-80PLUS80] -# Indicates supported Channel widths -# 0 = 160 MHz & 80+80 channel widths are not supported (default) -# 1 = 160 MHz channel width is supported -# 2 = 160 MHz & 80+80 channel widths are supported -# 3 = reserved -# -# Rx LDPC coding capability: [RXLDPC] -# Indicates support for receiving LDPC coded pkts -# 0 = Not supported (default) -# 1 = Supported -# -# Short GI for 80 MHz: [SHORT-GI-80] -# Indicates short GI support for reception of packets transmitted with TXVECTOR -# params format equal to VHT and CBW = 80Mhz -# 0 = Not supported (default) -# 1 = Supported -# -# Short GI for 160 MHz: [SHORT-GI-160] -# Indicates short GI support for reception of packets transmitted with TXVECTOR -# params format equal to VHT and CBW = 160Mhz -# 0 = Not supported (default) -# 1 = Supported -# -# Tx STBC: [TX-STBC-2BY1] -# Indicates support for the transmission of at least 2x1 STBC -# 0 = Not supported (default) -# 1 = Supported -# -# Rx STBC: [RX-STBC-1] [RX-STBC-12] [RX-STBC-123] [RX-STBC-1234] -# Indicates support for the reception of PPDUs using STBC -# 0 = Not supported (default) -# 1 = support of one spatial stream -# 2 = support of one and two spatial streams -# 3 = support of one, two and three spatial streams -# 4 = support of one, two, three and four spatial streams -# 5,6,7 = reserved -# -# SU Beamformer Capable: [SU-BEAMFORMER] -# Indicates support for operation as a single user beamformer -# 0 = Not supported (default) -# 1 = Supported -# -# SU Beamformee Capable: [SU-BEAMFORMEE] -# Indicates support for operation as a single user beamformee -# 0 = Not supported (default) -# 1 = Supported -# -# Compressed Steering Number of Beamformer Antennas Supported: -# [BF-ANTENNA-2] [BF-ANTENNA-3] [BF-ANTENNA-4] -# Beamformee's capability indicating the maximum number of beamformer -# antennas the beamformee can support when sending compressed beamforming -# feedback -# If SU beamformer capable, set to maximum value minus 1 -# else reserved (default) -# -# Number of Sounding Dimensions: -# [SOUNDING-DIMENSION-2] [SOUNDING-DIMENSION-3] [SOUNDING-DIMENSION-4] -# Beamformer's capability indicating the maximum value of the NUM_STS parameter -# in the TXVECTOR of a VHT NDP -# If SU beamformer capable, set to maximum value minus 1 -# else reserved (default) -# -# MU Beamformer Capable: [MU-BEAMFORMER] -# Indicates support for operation as an MU beamformer -# 0 = Not supported or sent by Non-AP STA (default) -# 1 = Supported -# -# VHT TXOP PS: [VHT-TXOP-PS] -# Indicates whether or not the AP supports VHT TXOP Power Save Mode -# or whether or not the STA is in VHT TXOP Power Save mode -# 0 = VHT AP doesn't support VHT TXOP PS mode (OR) VHT STA not in VHT TXOP PS -# mode -# 1 = VHT AP supports VHT TXOP PS mode (OR) VHT STA is in VHT TXOP power save -# mode -# -# +HTC-VHT Capable: [HTC-VHT] -# Indicates whether or not the STA supports receiving a VHT variant HT Control -# field. -# 0 = Not supported (default) -# 1 = supported -# -# Maximum A-MPDU Length Exponent: [MAX-A-MPDU-LEN-EXP0]..[MAX-A-MPDU-LEN-EXP7] -# Indicates the maximum length of A-MPDU pre-EOF padding that the STA can recv -# This field is an integer in the range of 0 to 7. -# The length defined by this field is equal to -# 2 pow(13 + Maximum A-MPDU Length Exponent) -1 octets -# -# VHT Link Adaptation Capable: [VHT-LINK-ADAPT2] [VHT-LINK-ADAPT3] -# Indicates whether or not the STA supports link adaptation using VHT variant -# HT Control field -# If +HTC-VHTcapable is 1 -# 0 = (no feedback) if the STA does not provide VHT MFB (default) -# 1 = reserved -# 2 = (Unsolicited) if the STA provides only unsolicited VHT MFB -# 3 = (Both) if the STA can provide VHT MFB in response to VHT MRQ and if the -# STA provides unsolicited VHT MFB -# Reserved if +HTC-VHTcapable is 0 -# -# Rx Antenna Pattern Consistency: [RX-ANTENNA-PATTERN] -# Indicates the possibility of Rx antenna pattern change -# 0 = Rx antenna pattern might change during the lifetime of an association -# 1 = Rx antenna pattern does not change during the lifetime of an association -# -# Tx Antenna Pattern Consistency: [TX-ANTENNA-PATTERN] -# Indicates the possibility of Tx antenna pattern change -# 0 = Tx antenna pattern might change during the lifetime of an association -# 1 = Tx antenna pattern does not change during the lifetime of an association -#vht_capab=[SHORT-GI-80][HTC-VHT] -# -# Require stations to support VHT PHY (reject association if they do not) -#require_vht=1 - -# 0 = 20 or 40 MHz operating Channel width -# 1 = 80 MHz channel width -# 2 = 160 MHz channel width -# 3 = 80+80 MHz channel width -#vht_oper_chwidth=1 -# -# center freq = 5 GHz + (5 * index) -# So index 42 gives center freq 5.210 GHz -# which is channel 42 in 5G band -# -#vht_oper_centr_freq_seg0_idx=42 -# -# center freq = 5 GHz + (5 * index) -# So index 159 gives center freq 5.795 GHz -# which is channel 159 in 5G band -# -#vht_oper_centr_freq_seg1_idx=159 - -# Workaround to use station's nsts capability in (Re)Association Response frame -# This may be needed with some deployed devices as an interoperability -# workaround for beamforming if the AP's capability is greater than the -# station's capability. This is disabled by default and can be enabled by -# setting use_sta_nsts=1. -#use_sta_nsts=0 - -##### IEEE 802.11ax related configuration ##################################### - -#ieee80211ax: Whether IEEE 802.11ax (HE) is enabled -# 0 = disabled (default) -# 1 = enabled -#ieee80211ax=1 - -# disable_11ax: Boolean (0/1) to disable HE for a specific BSS -#disable_11ax=0 - -#he_su_beamformer: HE single user beamformer support -# 0 = not supported (default) -# 1 = supported -#he_su_beamformer=1 - -#he_su_beamformee: HE single user beamformee support -# 0 = not supported (default) -# 1 = supported -#he_su_beamformee=1 - -#he_mu_beamformer: HE multiple user beamformer support -# 0 = not supported (default) -# 1 = supported -#he_mu_beamformer=1 - -# he_bss_color: BSS color (1-63) -#he_bss_color=1 - -# he_bss_color_partial: BSS color AID equation -#he_bss_color_partial=0 - -#he_default_pe_duration: The duration of PE field in an HE PPDU in us -# Possible values are 0 us (default), 4 us, 8 us, 12 us, and 16 us -#he_default_pe_duration=0 - -#he_twt_required: Whether TWT is required -# 0 = not required (default) -# 1 = required -#he_twt_required=0 - -#he_twt_responder: Whether TWT (HE) responder is enabled -# 0 = disabled -# 1 = enabled if supported by the driver (default) -#he_twt_responder=1 - -#he_rts_threshold: Duration of STA transmission -# 0 = not set (default) -# unsigned integer = duration in units of 16 us -#he_rts_threshold=0 - -#he_er_su_disable: Disable 242-tone HE ER SU PPDU reception by the AP -# 0 = enable reception (default) -# 1 = disable reception -#he_er_su_disable=0 - -# HE operating channel information; see matching vht_* parameters for details. -# he_oper_centr_freq_seg0_idx field is used to indicate center frequency of 80 -# and 160 MHz bandwidth operation. In 80+80 MHz operation, it is the center -# frequency of the lower frequency segment. he_oper_centr_freq_seg1_idx field -# is used only with 80+80 MHz bandwidth operation and it is used to transmit -# the center frequency of the second segment. -# On the 6 GHz band the center freq calculation starts from 5.950 GHz offset. -# For example idx=3 would result in 5965 MHz center frequency. In addition, -# he_oper_chwidth is ignored, and the channel width is derived from the -# configured operating class or center frequency indexes (see -# IEEE P802.11ax/D6.1 Annex E, Table E-4). -#he_oper_chwidth -#he_oper_centr_freq_seg0_idx -#he_oper_centr_freq_seg1_idx - -#he_basic_mcs_nss_set: Basic NSS/MCS set -# 16-bit combination of 2-bit values of Max HE-MCS For 1..8 SS; each 2-bit -# value having following meaning: -# 0 = HE-MCS 0-7, 1 = HE-MCS 0-9, 2 = HE-MCS 0-11, 3 = not supported -#he_basic_mcs_nss_set - -#he_mu_edca_qos_info_param_count -#he_mu_edca_qos_info_q_ack -#he_mu_edca_qos_info_queue_request=1 -#he_mu_edca_qos_info_txop_request -#he_mu_edca_ac_be_aifsn=0 -#he_mu_edca_ac_be_ecwmin=15 -#he_mu_edca_ac_be_ecwmax=15 -#he_mu_edca_ac_be_timer=255 -#he_mu_edca_ac_bk_aifsn=0 -#he_mu_edca_ac_bk_aci=1 -#he_mu_edca_ac_bk_ecwmin=15 -#he_mu_edca_ac_bk_ecwmax=15 -#he_mu_edca_ac_bk_timer=255 -#he_mu_edca_ac_vi_ecwmin=15 -#he_mu_edca_ac_vi_ecwmax=15 -#he_mu_edca_ac_vi_aifsn=0 -#he_mu_edca_ac_vi_aci=2 -#he_mu_edca_ac_vi_timer=255 -#he_mu_edca_ac_vo_aifsn=0 -#he_mu_edca_ac_vo_aci=3 -#he_mu_edca_ac_vo_ecwmin=15 -#he_mu_edca_ac_vo_ecwmax=15 -#he_mu_edca_ac_vo_timer=255 - -# Spatial Reuse Parameter Set -# -# SR Control field value -# B0 = PSR Disallowed -# B1 = Non-SRG OBSS PD SR Disallowed -# B2 = Non-SRG Offset Present -# B3 = SRG Information Present -# B4 = HESIGA_Spatial_reuse_value15_allowed -#he_spr_sr_control -# -# Non-SRG OBSS PD Max Offset (included if he_spr_sr_control B2=1) -#he_spr_non_srg_obss_pd_max_offset - -# SRG OBSS PD Min Offset (included if he_spr_sr_control B3=1) -#he_spr_srg_obss_pd_min_offset -# -# SRG OBSS PD Max Offset (included if he_spr_sr_control B3=1) -#he_spr_srg_obss_pd_max_offset -# -# SPR SRG BSS Color (included if he_spr_sr_control B3=1) -# This config represents SRG BSS Color Bitmap field of Spatial Reuse Parameter -# Set element that indicates the BSS color values used by members of the -# SRG of which the transmitting STA is a member. The value is in range of 0-63. -#he_spr_srg_bss_colors=1 2 10 63 -# -# SPR SRG Partial BSSID (included if he_spr_sr_control B3=1) -# This config represents SRG Partial BSSID Bitmap field of Spatial Reuse -# Parameter Set element that indicates the Partial BSSID values used by members -# of the SRG of which the transmitting STA is a member. The value range -# corresponds to one of the 64 possible values of BSSID[39:44], where the lowest -# numbered bit corresponds to Partial BSSID value 0 and the highest numbered bit -# corresponds to Partial BSSID value 63. -#he_spr_srg_partial_bssid=0 1 3 63 -# -#he_6ghz_max_mpdu: Maximum MPDU Length of HE 6 GHz band capabilities. -# Indicates maximum MPDU length -# 0 = 3895 octets -# 1 = 7991 octets -# 2 = 11454 octets (default) -#he_6ghz_max_mpdu=2 -# -#he_6ghz_max_ampdu_len_exp: Maximum A-MPDU Length Exponent of HE 6 GHz band -# capabilities. Indicates the maximum length of A-MPDU pre-EOF padding that -# the STA can receive. This field is an integer in the range of 0 to 7. -# The length defined by this field is equal to -# 2 pow(13 + Maximum A-MPDU Length Exponent) -1 octets -# 0 = AMPDU length of 8k -# 1 = AMPDU length of 16k -# 2 = AMPDU length of 32k -# 3 = AMPDU length of 65k -# 4 = AMPDU length of 131k -# 5 = AMPDU length of 262k -# 6 = AMPDU length of 524k -# 7 = AMPDU length of 1048k (default) -#he_6ghz_max_ampdu_len_exp=7 -# -#he_6ghz_rx_ant_pat: Rx Antenna Pattern Consistency of HE 6 GHz capability. -# Indicates the possibility of Rx antenna pattern change -# 0 = Rx antenna pattern might change during the lifetime of an association -# 1 = Rx antenna pattern does not change during the lifetime of an association -# (default) -#he_6ghz_rx_ant_pat=1 -# -#he_6ghz_tx_ant_pat: Tx Antenna Pattern Consistency of HE 6 GHz capability. -# Indicates the possibility of Tx antenna pattern change -# 0 = Tx antenna pattern might change during the lifetime of an association -# 1 = Tx antenna pattern does not change during the lifetime of an association -# (default) -#he_6ghz_tx_ant_pat=1 - -# 6 GHz Access Point type -# This config is to set the 6 GHz Access Point type. Possible options are: -# 0 = Indoor AP (default) -# 1 = Standard Power AP -# This has no impact for operation on other bands. -#he_6ghz_reg_pwr_type=0 - -# Unsolicited broadcast Probe Response transmission settings -# This is for the 6 GHz band only. If the interval is set to a non-zero value, -# the AP schedules unsolicited broadcast Probe Response frames to be -# transmitted for in-band discovery. Refer to -# IEEE P802.11ax/D8.0 26.17.2.3.2, AP behavior for fast passive scanning. -# Valid range: 0..20 TUs; default is 0 (disabled) -#unsol_bcast_probe_resp_interval=0 - -##### IEEE 802.11be related configuration ##################################### - -#ieee80211be: Whether IEEE 802.11be (EHT) is enabled -# 0 = disabled (default) -# 1 = enabled -#ieee80211be=1 - -#disable_11be: Boolean (0/1) to disable EHT for a specific BSS -#disable_11be=0 - -#eht_su_beamformer: EHT single user beamformer support -# 0 = not supported (default) -# 1 = supported -#eht_su_beamformer=1 - -#eht_su_beamformee: EHT single user beamformee support -# 0 = not supported (default) -# 1 = supported -#eht_su_beamformee=1 - -#eht_mu_beamformer: EHT multiple user beamformer support -# 0 = not supported (default) -# 1 = supported -#eht_mu_beamformer=1 - -# EHT operating channel information; see matching he_* parameters for details. -# The field eht_oper_centr_freq_seg0_idx field is used to indicate center -# frequency of 40, 80, and 160 MHz bandwidth operation. -# In the 6 GHz band, eht_oper_chwidth is ignored and the channel width is -# derived from the configured operating class (IEEE P802.11be/D1.5, -# Annex E.1 - Country information and operating classes). -#eht_oper_chwidth -#eht_oper_centr_freq_seg0_idx - -##### IEEE 802.1X-2004 related configuration ################################## - -# Require IEEE 802.1X authorization -#ieee8021x=1 - -# IEEE 802.1X/EAPOL version -# hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL -# version 2. However, there are many client implementations that do not handle -# the new version number correctly (they seem to drop the frames completely). -# In order to make hostapd interoperate with these clients, the version number -# can be set to the older version (1) with this configuration value. -# Note: When using MACsec, eapol_version shall be set to 3, which is -# defined in IEEE Std 802.1X-2010. -#eapol_version=2 - -# Optional displayable message sent with EAP Request-Identity. The first \0 -# in this string will be converted to ASCII-0 (nul). This can be used to -# separate network info (comma separated list of attribute=value pairs); see, -# e.g., RFC 4284. -#eap_message=hello -#eap_message=hello\0networkid=netw,nasid=foo,portid=0,NAIRealms=example.com - -# WEP rekeying (disabled if key lengths are not set or are set to 0) -# Key lengths for default/broadcast and individual/unicast keys: -# 5 = 40-bit WEP (also known as 64-bit WEP with 40 secret bits) -# 13 = 104-bit WEP (also known as 128-bit WEP with 104 secret bits) -#wep_key_len_broadcast=5 -#wep_key_len_unicast=5 -# Rekeying period in seconds. 0 = do not rekey (i.e., set keys only once) -#wep_rekey_period=300 - -# EAPOL-Key index workaround (set bit7) for WinXP Supplicant (needed only if -# only broadcast keys are used) eapol_key_index_workaround=0 - -# EAP reauthentication period in seconds (default: 3600 seconds; 0 = disable -# reauthentication). -# Note: Reauthentications may enforce a disconnection, check the related -# parameter wpa_deny_ptk0_rekey for details. -#eap_reauth_period=3600 - -# Use PAE group address (01:80:c2:00:00:03) instead of individual target -# address when sending EAPOL frames with driver=wired. This is the most common -# mechanism used in wired authentication, but it also requires that the port -# is only used by one station. -#use_pae_group_addr=1 - -# EAP Re-authentication Protocol (ERP) authenticator (RFC 6696) -# -# Whether to initiate EAP authentication with EAP-Initiate/Re-auth-Start before -# EAP-Identity/Request -#erp_send_reauth_start=1 -# -# Domain name for EAP-Initiate/Re-auth-Start. Omitted from the message if not -# set (no local ER server). This is also used by the integrated EAP server if -# ERP is enabled (eap_server_erp=1). -#erp_domain=example.com - -##### MACsec ################################################################## - -# macsec_policy: IEEE 802.1X/MACsec options -# This determines how sessions are secured with MACsec (only for MACsec -# drivers). -# 0: MACsec not in use (default) -# 1: MACsec enabled - Should secure, accept key server's advice to -# determine whether to use a secure session or not. -# -# macsec_integ_only: IEEE 802.1X/MACsec transmit mode -# This setting applies only when MACsec is in use, i.e., -# - macsec_policy is enabled -# - the key server has decided to enable MACsec -# 0: Encrypt traffic (default) -# 1: Integrity only -# -# macsec_replay_protect: IEEE 802.1X/MACsec replay protection -# This setting applies only when MACsec is in use, i.e., -# - macsec_policy is enabled -# - the key server has decided to enable MACsec -# 0: Replay protection disabled (default) -# 1: Replay protection enabled -# -# macsec_replay_window: IEEE 802.1X/MACsec replay protection window -# This determines a window in which replay is tolerated, to allow receipt -# of frames that have been misordered by the network. -# This setting applies only when MACsec replay protection active, i.e., -# - macsec_replay_protect is enabled -# - the key server has decided to enable MACsec -# 0: No replay window, strict check (default) -# 1..2^32-1: number of packets that could be misordered -# -# macsec_port: IEEE 802.1X/MACsec port -# Port component of the SCI -# Range: 1-65534 (default: 1) -# -# mka_priority (Priority of MKA Actor) -# Range: 0..255 (default: 255) -# -# macsec_csindex: IEEE 802.1X/MACsec cipher suite -# 0 = GCM-AES-128 (default) -# 1 = GCM-AES-256 (default) -# -# mka_cak, mka_ckn, and mka_priority: IEEE 802.1X/MACsec pre-shared key mode -# This allows to configure MACsec with a pre-shared key using a (CAK,CKN) pair. -# In this mode, instances of hostapd can act as MACsec peers. The peer -# with lower priority will become the key server and start distributing SAKs. -# mka_cak (CAK = Secure Connectivity Association Key) takes a 16-byte (128-bit) -# hex-string (32 hex-digits) or a 32-byte (256-bit) hex-string (64 hex-digits) -# mka_ckn (CKN = CAK Name) takes a 1..32-bytes (8..256 bit) hex-string -# (2..64 hex-digits) - -##### Integrated EAP server ################################################### - -# Optionally, hostapd can be configured to use an integrated EAP server -# to process EAP authentication locally without need for an external RADIUS -# server. This functionality can be used both as a local authentication server -# for IEEE 802.1X/EAPOL and as a RADIUS server for other devices. - -# Use integrated EAP server instead of external RADIUS authentication -# server. This is also needed if hostapd is configured to act as a RADIUS -# authentication server. eap_server=0 - -# Path for EAP server user database -# If SQLite support is included, this can be set to "sqlite:/path/to/sqlite.db" -# to use SQLite database instead of a text file. -#eap_user_file=/etc/hostapd.eap_user - -# CA certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS -#ca_cert=/etc/hostapd.ca.pem - -# Server certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS -#server_cert=/etc/hostapd.server.pem - -# Private key matching with the server certificate for EAP-TLS/PEAP/TTLS -# This may point to the same file as server_cert if both certificate and key -# are included in a single file. PKCS#12 (PFX) file (.p12/.pfx) can also be -# used by commenting out server_cert and specifying the PFX file as the -# private_key. -#private_key=/etc/hostapd.server.prv - -# Passphrase for private key -#private_key_passwd=secret passphrase - -# An alternative server certificate and private key can be configured with the -# following parameters (with values just like the parameters above without the -# '2' suffix). The ca_cert file (in PEM encoding) is used to add the trust roots -# for both server certificates and/or client certificates). -# -# The main use case for this alternative server certificate configuration is to -# enable both RSA and ECC public keys. The server will pick which one to use -# based on the client preferences for the cipher suite (in the TLS ClientHello -# message). It should be noted that number of deployed EAP peer implementations -# do not filter out the cipher suite list based on their local configuration and -# as such, configuration of alternative types of certificates on the server may -# result in interoperability issues. -#server_cert2=/etc/hostapd.server-ecc.pem -#private_key2=/etc/hostapd.server-ecc.prv -#private_key_passwd2=secret passphrase - - -# Server identity -# EAP methods that provide mechanism for authenticated server identity delivery -# use this value. If not set, "hostapd" is used as a default. -#server_id=server.example.com - -# Enable CRL verification. -# Note: hostapd does not yet support CRL downloading based on CDP. Thus, a -# valid CRL signed by the CA is required to be included in the ca_cert file. -# This can be done by using PEM format for CA certificate and CRL and -# concatenating these into one file. Whenever CRL changes, hostapd needs to be -# restarted to take the new CRL into use. Alternatively, crl_reload_interval can -# be used to configure periodic updating of the loaded CRL information. -# 0 = do not verify CRLs (default) -# 1 = check the CRL of the user certificate -# 2 = check all CRLs in the certificate path -#check_crl=1 - -# Specify whether to ignore certificate CRL validity time mismatches with -# errors X509_V_ERR_CRL_HAS_EXPIRED and X509_V_ERR_CRL_NOT_YET_VALID. -# -# 0 = ignore errors -# 1 = do not ignore errors (default) -#check_crl_strict=1 - -# CRL reload interval in seconds -# This can be used to reload ca_cert file and the included CRL on every new TLS -# session if difference between last reload and the current reload time in -# seconds is greater than crl_reload_interval. -# Note: If interval time is very short, CPU overhead may be negatively affected -# and it is advised to not go below 300 seconds. -# This is applicable only with check_crl values 1 and 2. -# 0 = do not reload CRLs (default) -# crl_reload_interval = 300 - -# If check_cert_subject is set, the value of every field will be checked -# against the DN of the subject in the client certificate. If the values do -# not match, the certificate verification will fail, rejecting the user. -# This option allows hostapd to match every individual field in the right order -# against the DN of the subject in the client certificate. -# -# For example, check_cert_subject=C=US/O=XX/OU=ABC/OU=XYZ/CN=1234 will check -# every individual DN field of the subject in the client certificate. If OU=XYZ -# comes first in terms of the order in the client certificate (DN field of -# client certificate C=US/O=XX/OU=XYZ/OU=ABC/CN=1234), hostapd will reject the -# client because the order of 'OU' is not matching the specified string in -# check_cert_subject. -# -# This option also allows '*' as a wildcard. This option has some limitation. -# It can only be used as per the following example. -# -# For example, check_cert_subject=C=US/O=XX/OU=Production* and we have two -# clients and DN of the subject in the first client certificate is -# (C=US/O=XX/OU=Production Unit) and DN of the subject in the second client is -# (C=US/O=XX/OU=Production Factory). In this case, hostapd will allow both -# clients because the value of 'OU' field in both client certificates matches -# 'OU' value in 'check_cert_subject' up to 'wildcard'. -# -# * (Allow all clients, e.g., check_cert_subject=*) -#check_cert_subject=string - -# TLS Session Lifetime in seconds -# This can be used to allow TLS sessions to be cached and resumed with an -# abbreviated handshake when using EAP-TLS/TTLS/PEAP. -# (default: 0 = session caching and resumption disabled) -#tls_session_lifetime=3600 - -# TLS flags -# [ALLOW-SIGN-RSA-MD5] = allow MD5-based certificate signatures (depending on -# the TLS library, these may be disabled by default to enforce stronger -# security) -# [DISABLE-TIME-CHECKS] = ignore certificate validity time (this requests -# the TLS library to accept certificates even if they are not currently -# valid, i.e., have expired or have not yet become valid; this should be -# used only for testing purposes) -# [DISABLE-TLSv1.0] = disable use of TLSv1.0 -# [ENABLE-TLSv1.0] = explicitly enable use of TLSv1.0 (this allows -# systemwide TLS policies to be overridden) -# [DISABLE-TLSv1.1] = disable use of TLSv1.1 -# [ENABLE-TLSv1.1] = explicitly enable use of TLSv1.1 (this allows -# systemwide TLS policies to be overridden) -# [DISABLE-TLSv1.2] = disable use of TLSv1.2 -# [ENABLE-TLSv1.2] = explicitly enable use of TLSv1.2 (this allows -# systemwide TLS policies to be overridden) -# [DISABLE-TLSv1.3] = disable use of TLSv1.3 -# [ENABLE-TLSv1.3] = enable TLSv1.3 (experimental - disabled by default) -#tls_flags=[flag1][flag2]... - -# Maximum number of EAP message rounds with data (default: 100) -#max_auth_rounds=100 - -# Maximum number of short EAP message rounds (default: 50) -#max_auth_rounds_short=50 - -# Cached OCSP stapling response (DER encoded) -# If set, this file is sent as a certificate status response by the EAP server -# if the EAP peer requests certificate status in the ClientHello message. -# This cache file can be updated, e.g., by running following command -# periodically to get an update from the OCSP responder: -# openssl ocsp \ -# -no_nonce \ -# -CAfile /etc/hostapd.ca.pem \ -# -issuer /etc/hostapd.ca.pem \ -# -cert /etc/hostapd.server.pem \ -# -url http://ocsp.example.com:8888/ \ -# -respout /tmp/ocsp-cache.der -#ocsp_stapling_response=/tmp/ocsp-cache.der - -# Cached OCSP stapling response list (DER encoded OCSPResponseList) -# This is similar to ocsp_stapling_response, but the extended version defined in -# RFC 6961 to allow multiple OCSP responses to be provided. -#ocsp_stapling_response_multi=/tmp/ocsp-multi-cache.der - -# dh_file: File path to DH/DSA parameters file (in PEM format) -# This is an optional configuration file for setting parameters for an -# ephemeral DH key exchange. If the file is in DSA parameters format, it will -# be automatically converted into DH params. If the used TLS library supports -# automatic DH parameter selection, that functionality will be used if this -# parameter is not set. DH parameters are required if anonymous EAP-FAST is -# used. -# You can generate DH parameters file with OpenSSL, e.g., -# "openssl dhparam -out /etc/hostapd.dh.pem 2048" -#dh_file=/etc/hostapd.dh.pem - -# OpenSSL cipher string -# -# This is an OpenSSL specific configuration option for configuring the default -# ciphers. If not set, the value configured at build time ("DEFAULT:!EXP:!LOW" -# by default) is used. -# See https://www.openssl.org/docs/apps/ciphers.html for OpenSSL documentation -# on cipher suite configuration. This is applicable only if hostapd is built to -# use OpenSSL. -#openssl_ciphers=DEFAULT:!EXP:!LOW - -# OpenSSL ECDH curves -# -# This is an OpenSSL specific configuration option for configuring the ECDH -# curves for EAP-TLS/TTLS/PEAP/FAST server. If not set, automatic curve -# selection is enabled. If set to an empty string, ECDH curve configuration is -# not done (the exact library behavior depends on the library version). -# Otherwise, this is a colon separated list of the supported curves (e.g., -# P-521:P-384:P-256). This is applicable only if hostapd is built to use -# OpenSSL. This must not be used for Suite B cases since the same OpenSSL -# parameter is set differently in those cases and this might conflict with that -# design. -#openssl_ecdh_curves=P-521:P-384:P-256 - -# Fragment size for EAP methods -#fragment_size=1400 - -# Finite cyclic group for EAP-pwd. Number maps to group of domain parameters -# using the IANA repository for IKE (RFC 2409). -#pwd_group=19 - -# Configuration data for EAP-SIM database/authentication gateway interface. -# This is a text string in implementation specific format. The example -# implementation in eap_sim_db.c uses this as the UNIX domain socket name for -# the HLR/AuC gateway (e.g., hlr_auc_gw). In this case, the path uses "unix:" -# prefix. If hostapd is built with SQLite support (CONFIG_SQLITE=y in .config), -# database file can be described with an optional db= parameter. -#eap_sim_db=unix:/tmp/hlr_auc_gw.sock -#eap_sim_db=unix:/tmp/hlr_auc_gw.sock db=/tmp/hostapd.db - -# EAP-SIM DB request timeout -# This parameter sets the maximum time to wait for a database request response. -# The parameter value is in seconds. -#eap_sim_db_timeout=1 - -# Encryption key for EAP-FAST PAC-Opaque values. This key must be a secret, -# random value. It is configured as a 16-octet value in hex format. It can be -# generated, e.g., with the following command: -# od -tx1 -v -N16 /dev/random | colrm 1 8 | tr -d ' ' -#pac_opaque_encr_key=000102030405060708090a0b0c0d0e0f - -# EAP-FAST authority identity (A-ID) -# A-ID indicates the identity of the authority that issues PACs. The A-ID -# should be unique across all issuing servers. In theory, this is a variable -# length field, but due to some existing implementations requiring A-ID to be -# 16 octets in length, it is strongly recommended to use that length for the -# field to provide interoperability with deployed peer implementations. This -# field is configured in hex format. -#eap_fast_a_id=101112131415161718191a1b1c1d1e1f - -# EAP-FAST authority identifier information (A-ID-Info) -# This is a user-friendly name for the A-ID. For example, the enterprise name -# and server name in a human-readable format. This field is encoded as UTF-8. -#eap_fast_a_id_info=test server - -# Enable/disable different EAP-FAST provisioning modes: -#0 = provisioning disabled -#1 = only anonymous provisioning allowed -#2 = only authenticated provisioning allowed -#3 = both provisioning modes allowed (default) -#eap_fast_prov=3 - -# EAP-FAST PAC-Key lifetime in seconds (hard limit) -#pac_key_lifetime=604800 - -# EAP-FAST PAC-Key refresh time in seconds (soft limit on remaining hard -# limit). The server will generate a new PAC-Key when this number of seconds -# (or fewer) of the lifetime remains. -#pac_key_refresh_time=86400 - -# EAP-TEAP authentication type -# 0 = inner EAP (default) -# 1 = Basic-Password-Auth -# 2 = Do not require Phase 2 authentication if client can be authenticated -# during Phase 1 -#eap_teap_auth=0 - -# EAP-TEAP authentication behavior when using PAC -# 0 = perform inner authentication (default) -# 1 = skip inner authentication (inner EAP/Basic-Password-Auth) -#eap_teap_pac_no_inner=0 - -# EAP-TEAP behavior with Result TLV -# 0 = include with Intermediate-Result TLV (default) -# 1 = send in a separate message (for testing purposes) -#eap_teap_separate_result=0 - -# EAP-TEAP identities -# 0 = allow any identity type (default) -# 1 = require user identity -# 2 = require machine identity -# 3 = request user identity; accept either user or machine identity -# 4 = request machine identity; accept either user or machine identity -# 5 = require both user and machine identity -#eap_teap_id=0 - -# EAP-SIM and EAP-AKA protected success/failure indication using AT_RESULT_IND -# (default: 0 = disabled). -#eap_sim_aka_result_ind=1 - -# EAP-SIM and EAP-AKA identity options -# 0 = do not use pseudonyms or fast reauthentication -# 1 = use pseudonyms, but not fast reauthentication -# 2 = do not use pseudonyms, but use fast reauthentication -# 3 = use pseudonyms and use fast reauthentication (default) -#eap_sim_id=3 - -# IMSI privacy key (PEM encoded RSA 2048-bit private key) for decrypting -# permanent identity when using EAP-SIM/AKA/AKA'. -#imsi_privacy_key=imsi-privacy-key.pem - -# Trusted Network Connect (TNC) -# If enabled, TNC validation will be required before the peer is allowed to -# connect. Note: This is only used with EAP-TTLS and EAP-FAST. If any other -# EAP method is enabled, the peer will be allowed to connect without TNC. -#tnc=1 - -# EAP Re-authentication Protocol (ERP) - RFC 6696 -# -# Whether to enable ERP on the EAP server. -#eap_server_erp=1 - - -##### RADIUS client configuration ############################################# -# for IEEE 802.1X with external Authentication Server, IEEE 802.11 -# authentication with external ACL for MAC addresses, and accounting - -# The own IP address of the access point (used as NAS-IP-Address) own_ip_addr=127.0.0.1 - -# NAS-Identifier string for RADIUS messages. When used, this should be unique -# to the NAS within the scope of the RADIUS server. Please note that hostapd -# uses a separate RADIUS client for each BSS and as such, a unique -# nas_identifier value should be configured separately for each BSS. This is -# particularly important for cases where RADIUS accounting is used -# (Accounting-On/Off messages are interpreted as clearing all ongoing sessions -# and that may get interpreted as applying to all BSSes if the same -# NAS-Identifier value is used.) For example, a fully qualified domain name -# prefixed with a unique identifier of the BSS (e.g., BSSID) can be used here. -# -# When using IEEE 802.11r, nas_identifier must be set and must be between 1 and -# 48 octets long. -# -# It is mandatory to configure either own_ip_addr or nas_identifier to be -# compliant with the RADIUS protocol. When using RADIUS accounting, it is -# strongly recommended that nas_identifier is set to a unique value for each -# BSS. -#nas_identifier=ap.example.com - -# RADIUS client forced local IP address for the access point -# Normally the local IP address is determined automatically based on configured -# IP addresses, but this field can be used to force a specific address to be -# used, e.g., when the device has multiple IP addresses. -#radius_client_addr=127.0.0.1 - -# RADIUS client forced local interface. Helps run properly with VRF -# Default is none set which allows the network stack to pick the appropriate -# interface automatically. -# Example below binds to eth0 -#radius_client_dev=eth0 - -# RADIUS authentication server -#auth_server_addr=127.0.0.1 -#auth_server_port=1812 -#auth_server_shared_secret=secret - -# RADIUS accounting server -#acct_server_addr=127.0.0.1 -#acct_server_port=1813 -#acct_server_shared_secret=secret - -# Secondary RADIUS servers; to be used if primary one does not reply to -# RADIUS packets. These are optional and there can be more than one secondary -# server listed. -#auth_server_addr=127.0.0.2 -#auth_server_port=1812 -#auth_server_shared_secret=secret2 -# -#acct_server_addr=127.0.0.2 -#acct_server_port=1813 -#acct_server_shared_secret=secret2 - -# Retry interval for trying to return to the primary RADIUS server (in -# seconds). RADIUS client code will automatically try to use the next server -# when the current server is not replying to requests. If this interval is set, -# primary server will be retried after configured amount of time even if the -# currently used secondary server is still working. -#radius_retry_primary_interval=600 - - -# Interim accounting update interval -# If this is set (larger than 0) and acct_server is configured, hostapd will -# send interim accounting updates every N seconds. Note: if set, this overrides -# possible Acct-Interim-Interval attribute in Access-Accept message. Thus, this -# value should not be configured in hostapd.conf, if RADIUS server is used to -# control the interim interval. -# This value should not be less 600 (10 minutes) and must not be less than -# 60 (1 minute). -#radius_acct_interim_interval=600 - -# Request Chargeable-User-Identity (RFC 4372) -# This parameter can be used to configure hostapd to request CUI from the -# RADIUS server by including Chargeable-User-Identity attribute into -# Access-Request packets. -#radius_request_cui=1 - -# Dynamic VLAN mode; allow RADIUS authentication server to decide which VLAN -# is used for the stations. This information is parsed from following RADIUS -# attributes based on RFC 3580 and RFC 2868: Tunnel-Type (value 13 = VLAN), -# Tunnel-Medium-Type (value 6 = IEEE 802), Tunnel-Private-Group-ID (value -# VLANID as a string). Optionally, the local MAC ACL list (accept_mac_file) can -# be used to set static client MAC address to VLAN ID mapping. -# Dynamic VLAN mode is also used with VLAN ID assignment based on WPA/WPA2 -# passphrase from wpa_psk_file or vlan_id parameter from sae_password. -# 0 = disabled (default); only VLAN IDs from accept_mac_file will be used -# 1 = optional; use default interface if RADIUS server does not include VLAN ID -# 2 = required; reject authentication if RADIUS server does not include VLAN ID -#dynamic_vlan=0 - -# Per-Station AP_VLAN interface mode -# If enabled, each station is assigned its own AP_VLAN interface. -# This implies per-station group keying and ebtables filtering of inter-STA -# traffic (when passed through the AP). -# If the sta is not assigned to any VLAN, then its AP_VLAN interface will be -# added to the bridge given by the "bridge" configuration option (see above). -# Otherwise, it will be added to the per-VLAN bridge. -# 0 = disabled (default) -# 1 = enabled -#per_sta_vif=0 - -# VLAN interface list for dynamic VLAN mode is read from a separate text file. -# This list is used to map VLAN ID from the RADIUS server to a network -# interface. Each station is bound to one interface in the same way as with -# multiple BSSIDs or SSIDs. Each line in this text file is defining a new -# interface and the line must include VLAN ID and interface name separated by -# white space (space or tab). -# If no entries are provided by this file, the station is statically mapped -# to . interfaces. -# Each line can optionally also contain the name of a bridge to add the VLAN to -#vlan_file=/etc/hostapd.vlan - -# Interface where 802.1q tagged packets should appear when a RADIUS server is -# used to determine which VLAN a station is on. hostapd creates a bridge for -# each VLAN. Then hostapd adds a VLAN interface (associated with the interface -# indicated by 'vlan_tagged_interface') and the appropriate wireless interface -# to the bridge. -#vlan_tagged_interface=eth0 - -# Bridge (prefix) to add the wifi and the tagged interface to. This gets the -# VLAN ID appended. It defaults to brvlan%d if no tagged interface is given -# and br%s.%d if a tagged interface is given, provided %s = tagged interface -# and %d = VLAN ID. -#vlan_bridge=brvlan - -# When hostapd creates a VLAN interface on vlan_tagged_interfaces, it needs -# to know how to name it. -# 0 = vlan, e.g., vlan1 -# 1 = ., e.g. eth0.1 -#vlan_naming=0 - -# Arbitrary RADIUS attributes can be added into Access-Request and -# Accounting-Request packets by specifying the contents of the attributes with -# the following configuration parameters. There can be multiple of these to -# add multiple attributes. These parameters can also be used to override some -# of the attributes added automatically by hostapd. -# Format: [:] -# attr_id: RADIUS attribute type (e.g., 26 = Vendor-Specific) -# syntax: s = string (UTF-8), d = integer, x = octet string -# value: attribute value in format indicated by the syntax -# If syntax and value parts are omitted, a null value (single 0x00 octet) is -# used. -# -# Additional Access-Request attributes -# radius_auth_req_attr=[:] -# Examples: -# Operator-Name = "Operator" -#radius_auth_req_attr=126:s:Operator -# Service-Type = Framed (2) -#radius_auth_req_attr=6:d:2 -# Connect-Info = "testing" (this overrides the automatically generated value) -#radius_auth_req_attr=77:s:testing -# Same Connect-Info value set as a hexdump -#radius_auth_req_attr=77:x:74657374696e67 - -# -# Additional Accounting-Request attributes -# radius_acct_req_attr=[:] -# Examples: -# Operator-Name = "Operator" -#radius_acct_req_attr=126:s:Operator - -# If SQLite support is included, path to a database from which additional -# RADIUS request attributes are extracted based on the station MAC address. -# -# The schema for the radius_attributes table is: -# id | sta | reqtype | attr : multi-key (sta, reqtype) -# id = autonumber -# sta = station MAC address in `11:22:33:44:55:66` format. -# type = `auth` | `acct` | NULL (match any) -# attr = existing config file format, e.g. `126:s:Test Operator` -#radius_req_attr_sqlite=radius_attr.sqlite - -# Dynamic Authorization Extensions (RFC 5176) -# This mechanism can be used to allow dynamic changes to user session based on -# commands from a RADIUS server (or some other disconnect client that has the -# needed session information). For example, Disconnect message can be used to -# request an associated station to be disconnected. -# -# This is disabled by default. Set radius_das_port to non-zero UDP port -# number to enable. -#radius_das_port=3799 -# -# DAS client (the host that can send Disconnect/CoA requests) and shared secret -# Format: -# IP address 0.0.0.0 can be used to allow requests from any address. -#radius_das_client=192.168.1.123 shared secret here -# -# DAS Event-Timestamp time window in seconds -#radius_das_time_window=300 -# -# DAS require Event-Timestamp -#radius_das_require_event_timestamp=1 -# -# DAS require Message-Authenticator -#radius_das_require_message_authenticator=1 - -##### RADIUS authentication server configuration ############################## - -# hostapd can be used as a RADIUS authentication server for other hosts. This -# requires that the integrated EAP server is also enabled and both -# authentication services are sharing the same configuration. - -# File name of the RADIUS clients configuration for the RADIUS server. If this -# commented out, RADIUS server is disabled. -#radius_server_clients=/etc/hostapd.radius_clients - -# The UDP port number for the RADIUS authentication server -#radius_server_auth_port=1812 - -# The UDP port number for the RADIUS accounting server -# Commenting this out or setting this to 0 can be used to disable RADIUS -# accounting while still enabling RADIUS authentication. -#radius_server_acct_port=1813 - -# Use IPv6 with RADIUS server (IPv4 will also be supported using IPv6 API) -#radius_server_ipv6=1 - - -##### WPA/IEEE 802.11i configuration ########################################## - -# Enable WPA. Setting this variable configures the AP to require WPA (either -# WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either -# wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK. -# Instead of wpa_psk / wpa_passphrase, wpa_psk_radius might suffice. -# For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys), -# RADIUS authentication server must be configured, and WPA-EAP must be included -# in wpa_key_mgmt. -# This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0) -# and/or WPA2 (full IEEE 802.11i/RSN): -# bit0 = WPA -# bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled) -# Note that WPA3 is also configured with bit1 since it uses RSN just like WPA2. -# In other words, for WPA3, wpa=2 is used the configuration (and -# wpa_key_mgmt=SAE for WPA3-Personal instead of wpa_key_mgmt=WPA-PSK). wpa=2 - -# Extended Key ID support for Individually Addressed frames -# -# Extended Key ID allows to rekey PTK keys without the impacts the "normal" -# PTK rekeying with only a single Key ID 0 has. It can only be used when the -# driver supports it and RSN/WPA2 is used with a CCMP/GCMP pairwise cipher. -# -# 0 = force off, i.e., use only Key ID 0 (default) -# 1 = enable and use Extended Key ID support when possible -# 2 = identical to 1 but start with Key ID 1 when possible -#extended_key_id=0 - -# WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit -# secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase -# (8..63 characters) that will be converted to PSK. This conversion uses SSID -# so the PSK changes when ASCII passphrase is used and the SSID is changed. -# wpa_psk (dot11RSNAConfigPSKValue) -# wpa_passphrase (dot11RSNAConfigPSKPassPhrase) -#wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef wpa_passphrase=chocolate1 - -# Optionally, WPA PSKs can be read from a separate text file (containing list -# of (PSK,MAC address) pairs. This allows more than one PSK to be configured. -# Use absolute path name to make sure that the files can be read on SIGHUP -# configuration reloads. -#wpa_psk_file=/etc/hostapd.wpa_psk - -# Optionally, WPA passphrase can be received from RADIUS authentication server -# This requires macaddr_acl to be set to 2 (RADIUS) for wpa_psk_radius values -# 1 and 2. -# 0 = disabled (default) -# 1 = optional; use default passphrase/psk if RADIUS server does not include -# Tunnel-Password -# 2 = required; reject authentication if RADIUS server does not include -# Tunnel-Password -# 3 = ask RADIUS server during 4-way handshake if there is no locally -# configured PSK/passphrase for the STA -#wpa_psk_radius=0 - -# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The -# entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be -# added to enable SHA256-based stronger algorithms. -# WPA-PSK = WPA-Personal / WPA2-Personal -# WPA-PSK-SHA256 = WPA2-Personal using SHA256 -# WPA-EAP = WPA-Enterprise / WPA2-Enterprise -# WPA-EAP-SHA256 = WPA2-Enterprise using SHA256 -# SAE = SAE (WPA3-Personal) -# WPA-EAP-SUITE-B-192 = WPA3-Enterprise with 192-bit security/CNSA suite -# FT-PSK = FT with passphrase/PSK -# FT-EAP = FT with EAP -# FT-EAP-SHA384 = FT with EAP using SHA384 -# FT-SAE = FT with SAE -# FILS-SHA256 = Fast Initial Link Setup with SHA256 -# FILS-SHA384 = Fast Initial Link Setup with SHA384 -# FT-FILS-SHA256 = FT and Fast Initial Link Setup with SHA256 -# FT-FILS-SHA384 = FT and Fast Initial Link Setup with SHA384 -# OWE = Opportunistic Wireless Encryption (a.k.a. Enhanced Open) -# DPP = Device Provisioning Protocol -# OSEN = Hotspot 2.0 online signup with encryption -# (dot11RSNAConfigAuthenticationSuitesTable) wpa_key_mgmt=SAE - -# Set of accepted cipher suites (encryption algorithms) for pairwise keys -# (unicast packets). This is a space separated list of algorithms: -# CCMP = AES in Counter mode with CBC-MAC (CCMP-128) -# TKIP = Temporal Key Integrity Protocol -# CCMP-256 = AES in Counter mode with CBC-MAC with 256-bit key -# GCMP = Galois/counter mode protocol (GCMP-128) -# GCMP-256 = Galois/counter mode protocol with 256-bit key -# Group cipher suite (encryption algorithm for broadcast and multicast frames) -# is automatically selected based on this configuration. If only CCMP is -# allowed as the pairwise cipher, group cipher will also be CCMP. Otherwise, -# TKIP will be used as the group cipher. The optional group_cipher parameter can -# be used to override this automatic selection. -# -# (dot11RSNAConfigPairwiseCiphersTable) -# Pairwise cipher for WPA (v1) (default: TKIP) -#wpa_pairwise=TKIP CCMP -# Pairwise cipher for RSN/WPA2 (default: use wpa_pairwise value) -#rsn_pairwise=CCMP - -# Optional override for automatic group cipher selection -# This can be used to select a specific group cipher regardless of which -# pairwise ciphers were enabled for WPA and RSN. It should be noted that -# overriding the group cipher with an unexpected value can result in -# interoperability issues and in general, this parameter is mainly used for -# testing purposes. -#group_cipher=CCMP - -# Time interval for rekeying GTK (broadcast/multicast encryption keys) in -# seconds. (dot11RSNAConfigGroupRekeyTime) -# This defaults to 86400 seconds (once per day) when using CCMP/GCMP as the -# group cipher and 600 seconds (once per 10 minutes) when using TKIP as the -# group cipher. -#wpa_group_rekey=86400 - -# Rekey GTK when any STA that possesses the current GTK is leaving the BSS. -# (dot11RSNAConfigGroupRekeyStrict) -#wpa_strict_rekey=1 - -# The number of times EAPOL-Key Message 1/2 in the RSN Group Key Handshake is -#retried per GTK Handshake attempt. (dot11RSNAConfigGroupUpdateCount) -# This value should only be increased when stations are constantly -# deauthenticated during GTK rekeying with the log message -# "group key handshake failed...". -# You should consider to also increase wpa_pairwise_update_count then. -# Range 1..4294967295; default: 4 -#wpa_group_update_count=4 - -# Time interval for rekeying GMK (master key used internally to generate GTKs -# (in seconds). -#wpa_gmk_rekey=86400 - -# Maximum lifetime for PTK in seconds. This can be used to enforce rekeying of -# PTK to mitigate some attacks against TKIP deficiencies. -# Warning: PTK rekeying is buggy with many drivers/devices and with such -# devices, the only secure method to rekey the PTK without Extended Key ID -# support requires a disconnection. Check the related parameter -# wpa_deny_ptk0_rekey for details. -#wpa_ptk_rekey=600 - -# Workaround for PTK rekey issues -# -# PTK0 rekeys (rekeying the PTK without "Extended Key ID for Individually -# Addressed Frames") can degrade the security and stability with some cards. -# To avoid such issues hostapd can replace those PTK rekeys (including EAP -# reauthentications) with disconnects. -# -# Available options: -# 0 = always rekey when configured/instructed (default) -# 1 = only rekey when the local driver is explicitly indicating it can perform -# this operation without issues -# 2 = never allow PTK0 rekeys -#wpa_deny_ptk0_rekey=0 - -# The number of times EAPOL-Key Message 1/4 and Message 3/4 in the RSN 4-Way -# Handshake are retried per 4-Way Handshake attempt. -# (dot11RSNAConfigPairwiseUpdateCount) -# Range 1..4294967295; default: 4 -#wpa_pairwise_update_count=4 - -# Workaround for key reinstallation attacks -# -# This parameter can be used to disable retransmission of EAPOL-Key frames that -# are used to install keys (EAPOL-Key message 3/4 and group message 1/2). This -# is similar to setting wpa_group_update_count=1 and -# wpa_pairwise_update_count=1, but with no impact to message 1/4 and with -# extended timeout on the response to avoid causing issues with stations that -# may use aggressive power saving have very long time in replying to the -# EAPOL-Key messages. -# -# This option can be used to work around key reinstallation attacks on the -# station (supplicant) side in cases those station devices cannot be updated -# for some reason. By removing the retransmissions the attacker cannot cause -# key reinstallation with a delayed frame transmission. This is related to the -# station side vulnerabilities CVE-2017-13077, CVE-2017-13078, CVE-2017-13079, -# CVE-2017-13080, and CVE-2017-13081. -# -# This workaround might cause interoperability issues and reduced robustness of -# key negotiation especially in environments with heavy traffic load due to the -# number of attempts to perform the key exchange is reduced significantly. As -# such, this workaround is disabled by default (unless overridden in build -# configuration). To enable this, set the parameter to 1. -#wpa_disable_eapol_key_retries=1 - -# Enable IEEE 802.11i/RSN/WPA2 pre-authentication. This is used to speed up -# roaming be pre-authenticating IEEE 802.1X/EAP part of the full RSN -# authentication and key handshake before actually associating with a new AP. -# (dot11RSNAPreauthenticationEnabled) -#rsn_preauth=1 -# -# Space separated list of interfaces from which pre-authentication frames are -# accepted (e.g., 'eth0' or 'eth0 wlan0wds0'. This list should include all -# interface that are used for connections to other APs. This could include -# wired interfaces and WDS links. The normal wireless data interface towards -# associated stations (e.g., wlan0) should not be added, since -# pre-authentication is only used with APs other than the currently associated -# one. -#rsn_preauth_interfaces=eth0 - -# ieee80211w: Whether management frame protection (MFP) is enabled -# 0 = disabled (default) -# 1 = optional -# 2 = required ieee80211w=2 -# The most common configuration options for this based on the PMF (protected -# management frames) certification program are: -# PMF enabled: ieee80211w=1 and wpa_key_mgmt=WPA-EAP WPA-EAP-SHA256 -# PMF required: ieee80211w=2 and wpa_key_mgmt=WPA-EAP-SHA256 -# (and similarly for WPA-PSK and WPA-PSK-SHA256 if WPA2-Personal is used) -# WPA3-Personal-only mode: ieee80211w=2 and wpa_key_mgmt=SAE - -# Group management cipher suite -# Default: AES-128-CMAC (BIP) -# Other options (depending on driver support): -# BIP-GMAC-128 -# BIP-GMAC-256 -# BIP-CMAC-256 -# Note: All the stations connecting to the BSS will also need to support the -# selected cipher. The default AES-128-CMAC is the only option that is commonly -# available in deployed devices. -#group_mgmt_cipher=AES-128-CMAC - -# Beacon Protection (management frame protection for Beacon frames) -# This depends on management frame protection being enabled (ieee80211w != 0) -# and beacon protection support indication from the driver. -# 0 = disabled (default) -# 1 = enabled -#beacon_prot=0 - -# Association SA Query maximum timeout (in TU = 1.024 ms; for MFP) -# (maximum time to wait for a SA Query response) -# dot11AssociationSAQueryMaximumTimeout, 1...4294967295 -#assoc_sa_query_max_timeout=1000 - -# Association SA Query retry timeout (in TU = 1.024 ms; for MFP) -# (time between two subsequent SA Query requests) -# dot11AssociationSAQueryRetryTimeout, 1...4294967295 -#assoc_sa_query_retry_timeout=201 - -# ocv: Operating Channel Validation -# This is a countermeasure against multi-channel on-path attacks. -# Enabling this depends on the driver's support for OCV when the driver SME is -# used. If hostapd SME is used, this will be enabled just based on this -# configuration. -# Enabling this automatically also enables ieee80211w, if not yet enabled. -# 0 = disabled (default) -# 1 = enabled -# 2 = enabled in workaround mode - Allow STA that claims OCV capability to -# connect even if the STA doesn't send OCI or negotiate PMF. This -# workaround is to improve interoperability with legacy STAs which are -# wrongly copying reserved bits of RSN capabilities from the AP's -# RSNE into (Re)Association Request frames. When this configuration is -# enabled, the AP considers STA is OCV capable only when the STA indicates -# MFP capability in (Re)Association Request frames and sends OCI in -# EAPOL-Key msg 2/4/FT Reassociation Request frame/FILS (Re)Association -# Request frame; otherwise, the AP disables OCV for the current connection -# with the STA. Enabling this workaround mode reduced OCV protection to -# some extend since it allows misbehavior to go through. As such, this -# should be enabled only if interoperability with misbehaving STAs is -# needed. -#ocv=1 - -# disable_pmksa_caching: Disable PMKSA caching -# This parameter can be used to disable caching of PMKSA created through EAP -# authentication. RSN preauthentication may still end up using PMKSA caching if -# it is enabled (rsn_preauth=1). -# 0 = PMKSA caching enabled (default) -# 1 = PMKSA caching disabled -#disable_pmksa_caching=0 - -# okc: Opportunistic Key Caching (aka Proactive Key Caching) -# Allow PMK cache to be shared opportunistically among configured interfaces -# and BSSes (i.e., all configurations within a single hostapd process). -# 0 = disabled (default) -# 1 = enabled -#okc=1 - -# SAE password -# This parameter can be used to set passwords for SAE. By default, the -# wpa_passphrase value is used if this separate parameter is not used, but -# wpa_passphrase follows the WPA-PSK constraints (8..63 characters) even though -# SAE passwords do not have such constraints. If the BSS enabled both SAE and -# WPA-PSK and both values are set, SAE uses the sae_password values and WPA-PSK -# uses the wpa_passphrase value. -# -# Each sae_password entry is added to a list of available passwords. This -# corresponds to the dot11RSNAConfigPasswordValueEntry. sae_password value -# starts with the password (dot11RSNAConfigPasswordCredential). That value can -# be followed by optional peer MAC address (dot11RSNAConfigPasswordPeerMac) and -# by optional password identifier (dot11RSNAConfigPasswordIdentifier). In -# addition, an optional VLAN ID specification can be used to bind the station -# to the specified VLAN whenever the specific SAE password entry is used. -# -# If the peer MAC address is not included or is set to the wildcard address -# (ff:ff:ff:ff:ff:ff), the entry is available for any station to use. If a -# specific peer MAC address is included, only a station with that MAC address -# is allowed to use the entry. -# -# If the password identifier (with non-zero length) is included, the entry is -# limited to be used only with that specified identifier. - -# The last matching (based on peer MAC address and identifier) entry is used to -# select which password to use. Setting sae_password to an empty string has a -# special meaning of removing all previously added entries. -# -# sae_password uses the following encoding: -#[|mac=][|vlanid=] -#[|pk=][|id=] -# Examples: -#sae_password=secret -#sae_password=really secret|mac=ff:ff:ff:ff:ff:ff -#sae_password=example secret|mac=02:03:04:05:06:07|id=pw identifier -#sae_password=example secret|vlanid=3|id=pw identifier - -# SAE threshold for anti-clogging mechanism (dot11RSNASAEAntiCloggingThreshold) -# This parameter defines how many open SAE instances can be in progress at the -# same time before the anti-clogging mechanism is taken into use. -#sae_anti_clogging_threshold=5 (deprecated) -#anti_clogging_threshold=5 - -# Maximum number of SAE synchronization errors (dot11RSNASAESync) -# The offending SAE peer will be disconnected if more than this many -# synchronization errors happen. -#sae_sync=5 - -# Enabled SAE finite cyclic groups -# SAE implementation are required to support group 19 (ECC group defined over a -# 256-bit prime order field). This configuration parameter can be used to -# specify a set of allowed groups. If not included, only the mandatory group 19 -# is enabled. -# The group values are listed in the IANA registry: -# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-9 -# Note that groups 1, 2, 5, 22, 23, and 24 should not be used in production -# purposes due limited security (see RFC 8247). Groups that are not as strong as -# group 19 (ECC, NIST P-256) are unlikely to be useful for production use cases -# since all implementations are required to support group 19. -#sae_groups=19 20 21 - -# Require MFP for all associations using SAE -# This parameter can be used to enforce negotiation of MFP for all associations -# that negotiate use of SAE. This is used in cases where SAE-capable devices are -# known to be MFP-capable and the BSS is configured with optional MFP -# (ieee80211w=1) for legacy support. The non-SAE stations can connect without -# MFP while SAE stations are required to negotiate MFP if sae_require_mfp=1. -#sae_require_mfp=0 - -# SAE Confirm behavior -# By default, AP will send out only SAE Commit message in response to a received -# SAE Commit message. This parameter can be set to 1 to override that behavior -# to send both SAE Commit and SAE Confirm messages without waiting for the STA -# to send its SAE Confirm message first. -#sae_confirm_immediate=0 - -# SAE mechanism for PWE derivation -# 0 = hunting-and-pecking loop only (default without password identifier) -# 1 = hash-to-element only (default with password identifier) -# 2 = both hunting-and-pecking loop and hash-to-element enabled -# Note: The default value is likely to change from 0 to 2 once the new -# hash-to-element mechanism has received more interoperability testing. -# When using SAE password identifier, the hash-to-element mechanism is used -# regardless of the sae_pwe parameter value. -#sae_pwe=0 - -# FILS Cache Identifier (16-bit value in hexdump format) -#fils_cache_id=0011 - -# FILS Realm Information -# One or more FILS realms need to be configured when FILS is enabled. This list -# of realms is used to define which realms (used in keyName-NAI by the client) -# can be used with FILS shared key authentication for ERP. -#fils_realm=example.com -#fils_realm=example.org - -# FILS DH Group for PFS -# 0 = PFS disabled with FILS shared key authentication (default) -# 1-65535 DH Group to use for FILS PFS -#fils_dh_group=0 - -# OWE DH groups -# OWE implementations are required to support group 19 (NIST P-256). All groups -# that are supported by the implementation (e.g., groups 19, 20, and 21 when -# using OpenSSL) are enabled by default. This configuration parameter can be -# used to specify a limited set of allowed groups. The group values are listed -# in the IANA registry: -# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-10 -#owe_groups=19 20 21 - -# OWE PTK derivation workaround -# Initial OWE implementation used SHA256 when deriving the PTK for all OWE -# groups. This was supposed to change to SHA384 for group 20 and SHA512 for -# group 21. This parameter can be used to enable workaround for interoperability -# with stations that use SHA256 with groups 20 and 21. By default (0) only the -# appropriate hash function is accepted. When workaround is enabled (1), the -# appropriate hash function is tried first and if that fails, SHA256-based PTK -# derivation is attempted. This workaround can result in reduced security for -# groups 20 and 21, but is required for interoperability with older -# implementations. There is no impact to group 19 behavior. The workaround is -# disabled by default and can be enabled by uncommenting the following line. -#owe_ptk_workaround=1 - -# OWE transition mode configuration -# Pointer to the matching open/OWE BSS -#owe_transition_bssid= -# SSID in same format as ssid2 described above. -#owe_transition_ssid= -# Alternatively, OWE transition mode BSSID/SSID can be configured with a -# reference to a BSS operated by this hostapd process. -#owe_transition_ifname= - -# DHCP server for FILS HLP -# If configured, hostapd will act as a DHCP relay for all FILS HLP requests -# that include a DHCPDISCOVER message and send them to the specific DHCP -# server for processing. hostapd will then wait for a response from that server -# before replying with (Re)Association Response frame that encapsulates this -# DHCP response. own_ip_addr is used as the local address for the communication -# with the DHCP server. -#dhcp_server=127.0.0.1 - -# DHCP server UDP port -# Default: 67 -#dhcp_server_port=67 - -# DHCP relay UDP port on the local device -# Default: 67; 0 means not to bind any specific port -#dhcp_relay_port=67 - -# DHCP rapid commit proxy -# If set to 1, this enables hostapd to act as a DHCP rapid commit proxy to -# allow the rapid commit options (two message DHCP exchange) to be used with a -# server that supports only the four message DHCP exchange. This is disabled by -# default (= 0) and can be enabled by setting this to 1. -#dhcp_rapid_commit_proxy=0 - -# Wait time for FILS HLP (dot11HLPWaitTime) in TUs -# default: 30 TUs (= 30.72 milliseconds) -#fils_hlp_wait_time=30 - -# FILS Discovery frame transmission minimum and maximum interval settings. -# If fils_discovery_max_interval is non-zero, the AP enables FILS Discovery -# frame transmission. These values use TUs as the unit and have allowed range -# of 0-10000. fils_discovery_min_interval defaults to 20. -#fils_discovery_min_interval=20 -#fils_discovery_max_interval=0 - -# Transition Disable indication -# The AP can notify authenticated stations to disable transition mode in their -# network profiles when the network has completed transition steps, i.e., once -# sufficiently large number of APs in the ESS have been updated to support the -# more secure alternative. When this indication is used, the stations are -# expected to automatically disable transition mode and less secure security -# options. This includes use of WEP, TKIP (including use of TKIP as the group -# cipher), and connections without PMF. -# Bitmap bits: -# bit 0 (0x01): WPA3-Personal (i.e., disable WPA2-Personal = WPA-PSK and only -# allow SAE to be used) -# bit 1 (0x02): SAE-PK (disable SAE without use of SAE-PK) -# bit 2 (0x04): WPA3-Enterprise (move to requiring PMF) -# bit 3 (0x08): Enhanced Open (disable use of open network; require OWE) -# (default: 0 = do not include Transition Disable KDE) -#transition_disable=0x01 - -# PASN ECDH groups -# PASN implementations are required to support group 19 (NIST P-256). If this -# parameter is not set, only group 19 is supported by default. This -# configuration parameter can be used to specify a limited set of allowed -# groups. The group values are listed in the IANA registry: -# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-10 -#pasn_groups=19 20 21 - -# PASN comeback after time in TUs -# In case the AP is temporarily unable to handle a PASN authentication exchange -# due to a too large number of parallel operations, this value indicates to the -# peer after how many TUs it can try the PASN exchange again. -# (default: 10 TUs) -#pasn_comeback_after=10 - -##### IEEE 802.11r configuration ############################################## - -# Mobility Domain identifier (dot11FTMobilityDomainID, MDID) -# MDID is used to indicate a group of APs (within an ESS, i.e., sharing the -# same SSID) between which a STA can use Fast BSS Transition. -# 2-octet identifier as a hex string. -#mobility_domain=a1b2 - -# PMK-R0 Key Holder identifier (dot11FTR0KeyHolderID) -# 1 to 48 octet identifier. -# This is configured with nas_identifier (see RADIUS client section above). - -# Default lifetime of the PMK-R0 in seconds; range 60..4294967295 -# (default: 14 days / 1209600 seconds; 0 = disable timeout) -# (dot11FTR0KeyLifetime) -#ft_r0_key_lifetime=1209600 - -# Maximum lifetime for PMK-R1; applied only if not zero -# PMK-R1 is removed at latest after this limit. -# Removing any PMK-R1 for expiry can be disabled by setting this to -1. -# (default: 0) -#r1_max_key_lifetime=0 - -# PMK-R1 Key Holder identifier (dot11FTR1KeyHolderID) -# 6-octet identifier as a hex string. -# Defaults to BSSID. -#r1_key_holder=000102030405 - -# Reassociation deadline in time units (TUs / 1.024 ms; range 1000..65535) -# (dot11FTReassociationDeadline) -#reassociation_deadline=1000 - -# List of R0KHs in the same Mobility Domain -# format: <256-bit key as hex string> -# This list is used to map R0KH-ID (NAS Identifier) to a destination MAC -# address when requesting PMK-R1 key from the R0KH that the STA used during the -# Initial Mobility Domain Association. -#r0kh=02:01:02:03:04:05 r0kh-1.example.com 000102030405060708090a0b0c0d0e0f000102030405060708090a0b0c0d0e0f -#r0kh=02:01:02:03:04:06 r0kh-2.example.com 00112233445566778899aabbccddeeff00112233445566778899aabbccddeeff -# And so on.. One line per R0KH. -# Wildcard entry: -# Upon receiving a response from R0KH, it will be added to this list, so -# subsequent requests won't be broadcast. If R0KH does not reply, it will be -# temporarily blocked (see rkh_neg_timeout). -#r0kh=ff:ff:ff:ff:ff:ff * 00112233445566778899aabbccddeeff - -# List of R1KHs in the same Mobility Domain -# format: <256-bit key as hex string> -# This list is used to map R1KH-ID to a destination MAC address when sending -# PMK-R1 key from the R0KH. This is also the list of authorized R1KHs in the MD -# that can request PMK-R1 keys. -#r1kh=02:01:02:03:04:05 02:11:22:33:44:55 000102030405060708090a0b0c0d0e0f000102030405060708090a0b0c0d0e0f -#r1kh=02:01:02:03:04:06 02:11:22:33:44:66 00112233445566778899aabbccddeeff00112233445566778899aabbccddeeff -# And so on.. One line per R1KH. -# Wildcard entry: -# Upon receiving a request from an R1KH not yet known, it will be added to this -# list and thus will receive push notifications. -#r1kh=00:00:00:00:00:00 00:00:00:00:00:00 00112233445566778899aabbccddeeff - -# Timeout (seconds) for newly discovered R0KH/R1KH (see wildcard entries above) -# Special values: 0 -> do not expire -# Warning: do not cache implies no sequence number validation with wildcards -#rkh_pos_timeout=86400 (default = 1 day) - -# Timeout (milliseconds) for requesting PMK-R1 from R0KH using PULL request -# and number of retries. -#rkh_pull_timeout=1000 (default = 1 second) -#rkh_pull_retries=4 (default) - -# Timeout (seconds) for non replying R0KH (see wildcard entries above) -# Special values: 0 -> do not cache -# default: 60 seconds -#rkh_neg_timeout=60 - -# Note: The R0KH/R1KH keys used to be 128-bit in length before the message -# format was changed. That shorter key length is still supported for backwards -# compatibility of the configuration files. If such a shorter key is used, a -# 256-bit key is derived from it. For new deployments, configuring the 256-bit -# key is recommended. - -# Whether PMK-R1 push is enabled at R0KH -# 0 = do not push PMK-R1 to all configured R1KHs (default) -# 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived -#pmk_r1_push=1 - -# Whether to enable FT-over-DS -# 0 = FT-over-DS disabled -# 1 = FT-over-DS enabled (default) -#ft_over_ds=1 - -# Whether to generate FT response locally for PSK networks -# This avoids use of PMK-R1 push/pull from other APs with FT-PSK networks as -# the required information (PSK and other session data) is already locally -# available. -# 0 = disabled (default) -# 1 = enabled -#ft_psk_generate_local=0 - -##### Neighbor table ########################################################## -# Maximum number of entries kept in AP table (either for neighbor table or for -# detecting Overlapping Legacy BSS Condition). The oldest entry will be -# removed when adding a new entry that would make the list grow over this -# limit. Note! WFA certification for IEEE 802.11g requires that OLBC is -# enabled, so this field should not be set to 0 when using IEEE 802.11g. -# default: 255 -#ap_table_max_size=255 - -# Number of seconds of no frames received after which entries may be deleted -# from the AP table. Since passive scanning is not usually performed frequently -# this should not be set to very small value. In addition, there is no -# guarantee that every scan cycle will receive beacon frames from the -# neighboring APs. -# default: 60 -#ap_table_expiration_time=3600 - -# Maximum number of stations to track on the operating channel -# This can be used to detect dualband capable stations before they have -# associated, e.g., to provide guidance on which colocated BSS to use. -# Default: 0 (disabled) -#track_sta_max_num=100 - -# Maximum age of a station tracking entry in seconds -# Default: 180 -#track_sta_max_age=180 - -# Do not reply to group-addressed Probe Request from a station that was seen on -# another radio. -# Default: Disabled -# -# This can be used with enabled track_sta_max_num configuration on another -# interface controlled by the same hostapd process to restrict Probe Request -# frame handling from replying to group-addressed Probe Request frames from a -# station that has been detected to be capable of operating on another band, -# e.g., to try to reduce likelihood of the station selecting a 2.4 GHz BSS when -# the AP operates both a 2.4 GHz and 5 GHz BSS concurrently. -# -# Note: Enabling this can cause connectivity issues and increase latency for -# discovering the AP. -#no_probe_resp_if_seen_on=wlan1 - -# Reject authentication from a station that was seen on another radio. -# Default: Disabled -# -# This can be used with enabled track_sta_max_num configuration on another -# interface controlled by the same hostapd process to reject authentication -# attempts from a station that has been detected to be capable of operating on -# another band, e.g., to try to reduce likelihood of the station selecting a -# 2.4 GHz BSS when the AP operates both a 2.4 GHz and 5 GHz BSS concurrently. -# -# Note: Enabling this can cause connectivity issues and increase latency for -# connecting with the AP. -#no_auth_if_seen_on=wlan1 - -##### Wi-Fi Protected Setup (WPS) ############################################# - -# WPS state -# 0 = WPS disabled (default) -# 1 = WPS enabled, not configured -# 2 = WPS enabled, configured -#wps_state=2 - -# Whether to manage this interface independently from other WPS interfaces -# By default, a single hostapd process applies WPS operations to all configured -# interfaces. This parameter can be used to disable that behavior for a subset -# of interfaces. If this is set to non-zero for an interface, WPS commands -# issued on that interface do not apply to other interfaces and WPS operations -# performed on other interfaces do not affect this interface. -#wps_independent=0 - -# AP can be configured into a locked state where new WPS Registrar are not -# accepted, but previously authorized Registrars (including the internal one) -# can continue to add new Enrollees. -#ap_setup_locked=1 - -# Universally Unique IDentifier (UUID; see RFC 4122) of the device -# This value is used as the UUID for the internal WPS Registrar. If the AP -# is also using UPnP, this value should be set to the device's UPnP UUID. -# If not configured, UUID will be generated based on the local MAC address. -#uuid=12345678-9abc-def0-1234-56789abcdef0 - -# Note: If wpa_psk_file is set, WPS is used to generate random, per-device PSKs -# that will be appended to the wpa_psk_file. If wpa_psk_file is not set, the -# default PSK (wpa_psk/wpa_passphrase) will be delivered to Enrollees. Use of -# per-device PSKs is recommended as the more secure option (i.e., make sure to -# set wpa_psk_file when using WPS with WPA-PSK). - -# When an Enrollee requests access to the network with PIN method, the Enrollee -# PIN will need to be entered for the Registrar. PIN request notifications are -# sent to hostapd ctrl_iface monitor. In addition, they can be written to a -# text file that could be used, e.g., to populate the AP administration UI with -# pending PIN requests. If the following variable is set, the PIN requests will -# be written to the configured file. -#wps_pin_requests=/var/run/hostapd_wps_pin_requests - -# Device Name -# User-friendly description of device; up to 32 octets encoded in UTF-8 -#device_name=Wireless AP - -# Manufacturer -# The manufacturer of the device (up to 64 ASCII characters) -#manufacturer=Company - -# Model Name -# Model of the device (up to 32 ASCII characters) -#model_name=WAP - -# Model Number -# Additional device description (up to 32 ASCII characters) -#model_number=123 - -# Serial Number -# Serial number of the device (up to 32 characters) -#serial_number=12345 - -# Primary Device Type -# Used format: -- -# categ = Category as an integer value -# OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for -# default WPS OUI -# subcateg = OUI-specific Sub Category as an integer value -# Examples: -# 1-0050F204-1 (Computer / PC) -# 1-0050F204-2 (Computer / Server) -# 5-0050F204-1 (Storage / NAS) -# 6-0050F204-1 (Network Infrastructure / AP) -#device_type=6-0050F204-1 - -# OS Version -# 4-octet operating system version number (hex string) -#os_version=01020300 - -# Config Methods -# List of the supported configuration methods -# Available methods: usba ethernet label display ext_nfc_token int_nfc_token -# nfc_interface push_button keypad virtual_display physical_display -# virtual_push_button physical_push_button -#config_methods=label virtual_display virtual_push_button keypad - -# WPS capability discovery workaround for PBC with Windows 7 -# Windows 7 uses incorrect way of figuring out AP's WPS capabilities by acting -# as a Registrar and using M1 from the AP. The config methods attribute in that -# message is supposed to indicate only the configuration method supported by -# the AP in Enrollee role, i.e., to add an external Registrar. For that case, -# PBC shall not be used and as such, the PushButton config method is removed -# from M1 by default. If pbc_in_m1=1 is included in the configuration file, -# the PushButton config method is left in M1 (if included in config_methods -# parameter) to allow Windows 7 to use PBC instead of PIN (e.g., from a label -# in the AP). -#pbc_in_m1=1 - -# Static access point PIN for initial configuration and adding Registrars -# If not set, hostapd will not allow external WPS Registrars to control the -# access point. The AP PIN can also be set at runtime with hostapd_cli -# wps_ap_pin command. Use of temporary (enabled by user action) and random -# AP PIN is much more secure than configuring a static AP PIN here. As such, -# use of the ap_pin parameter is not recommended if the AP device has means for -# displaying a random PIN. -#ap_pin=12345670 - -# Skip building of automatic WPS credential -# This can be used to allow the automatically generated Credential attribute to -# be replaced with pre-configured Credential(s). -#skip_cred_build=1 - -# Additional Credential attribute(s) -# This option can be used to add pre-configured Credential attributes into M8 -# message when acting as a Registrar. If skip_cred_build=1, this data will also -# be able to override the Credential attribute that would have otherwise been -# automatically generated based on network configuration. This configuration -# option points to an external file that much contain the WPS Credential -# attribute(s) as binary data. -#extra_cred=hostapd.cred - -# Credential processing -# 0 = process received credentials internally (default) -# 1 = do not process received credentials; just pass them over ctrl_iface to -# external program(s) -# 2 = process received credentials internally and pass them over ctrl_iface -# to external program(s) -# Note: With wps_cred_processing=1, skip_cred_build should be set to 1 and -# extra_cred be used to provide the Credential data for Enrollees. -# -# wps_cred_processing=1 will disabled automatic updates of hostapd.conf file -# both for Credential processing and for marking AP Setup Locked based on -# validation failures of AP PIN. An external program is responsible on updating -# the configuration appropriately in this case. -#wps_cred_processing=0 - -# Whether to enable SAE (WPA3-Personal transition mode) automatically for -# WPA2-PSK credentials received using WPS. -# 0 = only add the explicitly listed WPA2-PSK configuration (default) -# 1 = add both the WPA2-PSK and SAE configuration and enable PMF so that the -# AP gets configured in WPA3-Personal transition mode (supports both -# WPA2-Personal (PSK) and WPA3-Personal (SAE) clients). -#wps_cred_add_sae=0 - -# AP Settings Attributes for M7 -# By default, hostapd generates the AP Settings Attributes for M7 based on the -# current configuration. It is possible to override this by providing a file -# with pre-configured attributes. This is similar to extra_cred file format, -# but the AP Settings attributes are not encapsulated in a Credential -# attribute. -#ap_settings=hostapd.ap_settings - -# Multi-AP backhaul BSS config -# Used in WPS when multi_ap=2 or 3. Defines "backhaul BSS" credentials. -# These are passed in WPS M8 instead of the normal (fronthaul) credentials -# if the Enrollee has the Multi-AP subelement set. Backhaul SSID is formatted -# like ssid2. The key is set like wpa_psk or wpa_passphrase. -#multi_ap_backhaul_ssid="backhaul" -#multi_ap_backhaul_wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef -#multi_ap_backhaul_wpa_passphrase=secret passphrase - -# WPS UPnP interface -# If set, support for external Registrars is enabled. -#upnp_iface=br0 - -# Friendly Name (required for UPnP) -# Short description for end use. Should be less than 64 characters. -#friendly_name=WPS Access Point - -# Manufacturer URL (optional for UPnP) -#manufacturer_url=http://www.example.com/ - -# Model Description (recommended for UPnP) -# Long description for end user. Should be less than 128 characters. -#model_description=Wireless Access Point - -# Model URL (optional for UPnP) -#model_url=http://www.example.com/model/ - -# Universal Product Code (optional for UPnP) -# 12-digit, all-numeric code that identifies the consumer package. -#upc=123456789012 - -# WPS RF Bands (a = 5G, b = 2.4G, g = 2.4G, ag = dual band, ad = 60 GHz) -# This value should be set according to RF band(s) supported by the AP if -# hw_mode is not set. For dual band dual concurrent devices, this needs to be -# set to ag to allow both RF bands to be advertized. -#wps_rf_bands=ag - -# NFC password token for WPS -# These parameters can be used to configure a fixed NFC password token for the -# AP. This can be generated, e.g., with nfc_pw_token from wpa_supplicant. When -# these parameters are used, the AP is assumed to be deployed with a NFC tag -# that includes the matching NFC password token (e.g., written based on the -# NDEF record from nfc_pw_token). -# -#wps_nfc_dev_pw_id: Device Password ID (16..65535) -#wps_nfc_dh_pubkey: Hexdump of DH Public Key -#wps_nfc_dh_privkey: Hexdump of DH Private Key -#wps_nfc_dev_pw: Hexdump of Device Password - -# Application Extension attribute for Beacon and Probe Response frames -# This parameter can be used to add application extension into WPS IE. The -# contents of this parameter starts with 16-octet (32 hexdump characters) of -# UUID to identify the specific application and that is followed by the actual -# application specific data. -#wps_application_ext= - -##### Wi-Fi Direct (P2P) ###################################################### - -# Enable P2P Device management -#manage_p2p=1 - -# Allow cross connection -#allow_cross_connection=1 - -##### Device Provisioning Protocol (DPP) ###################################### - -# Name for Enrollee's DPP Configuration Request -#dpp_name=Test - -# MUD URL for Enrollee's DPP Configuration Request (optional) -#dpp_mud_url=https://example.com/mud - -#dpp_connector -#dpp_netaccesskey -#dpp_netaccesskey_expiry -#dpp_csign -#dpp_controller - -# Configurator Connectivity indication -# 0: no Configurator is currently connected (default) -# 1: advertise that a Configurator is available -#dpp_configurator_connectivity=0 - -# DPP PFS -# 0: allow PFS to be used or not used (default) -# 1: require PFS to be used (note: not compatible with DPP R1) -# 2: do not allow PFS to be used -#dpp_pfs=0 - -#### TDLS (IEEE 802.11z-2010) ################################################# - -# Prohibit use of TDLS in this BSS -#tdls_prohibit=1 - -# Prohibit use of TDLS Channel Switching in this BSS -#tdls_prohibit_chan_switch=1 - -##### IEEE 802.11v-2011 ####################################################### - -# Time advertisement -# 0 = disabled (default) -# 2 = UTC time at which the TSF timer is 0 -#time_advertisement=2 - -# Local time zone as specified in 8.3 of IEEE Std 1003.1-2004: -# stdoffset[dst[offset][,start[/time],end[/time]]] -#time_zone=EST5 - -# WNM-Sleep Mode (extended sleep mode for stations) -# 0 = disabled (default) -# 1 = enabled (allow stations to use WNM-Sleep Mode) -#wnm_sleep_mode=1 - -# WNM-Sleep Mode GTK/IGTK workaround -# Normally, WNM-Sleep Mode exit with management frame protection negotiated -# would result in the current GTK/IGTK getting added into the WNM-Sleep Mode -# Response frame. Some station implementations may have a vulnerability that -# results in GTK/IGTK reinstallation based on this frame being replayed. This -# configuration parameter can be used to disable that behavior and use EAPOL-Key -# frames for GTK/IGTK update instead. This would likely be only used with -# wpa_disable_eapol_key_retries=1 that enables a workaround for similar issues -# with EAPOL-Key. This is related to station side vulnerabilities CVE-2017-13087 -# and CVE-2017-13088. To enable this AP-side workaround, set the parameter to 1. -#wnm_sleep_mode_no_keys=0 - -# BSS Transition Management -# 0 = disabled (default) -# 1 = enabled -#bss_transition=1 - -# Proxy ARP -# 0 = disabled (default) -# 1 = enabled -#proxy_arp=1 - -# IPv6 Neighbor Advertisement multicast-to-unicast conversion -# This can be used with Proxy ARP to allow multicast NAs to be forwarded to -# associated STAs using link layer unicast delivery. -# 0 = disabled (default) -# 1 = enabled -#na_mcast_to_ucast=0 - -##### IEEE 802.11u-2011 ####################################################### - -# Enable Interworking service -#interworking=1 - -# Access Network Type -# 0 = Private network -# 1 = Private network with guest access -# 2 = Chargeable public network -# 3 = Free public network -# 4 = Personal device network -# 5 = Emergency services only network -# 14 = Test or experimental -# 15 = Wildcard -#access_network_type=0 - -# Whether the network provides connectivity to the Internet -# 0 = Unspecified -# 1 = Network provides connectivity to the Internet -#internet=1 - -# Additional Step Required for Access -# Note: This is only used with open network, i.e., ASRA shall ne set to 0 if -# RSN is used. -#asra=0 - -# Emergency services reachable -#esr=0 - -# Unauthenticated emergency service accessible -#uesa=0 - -# Venue Info (optional) -# The available values are defined in IEEE Std 802.11u-2011, 7.3.1.34. -# Example values (group,type): -# 0,0 = Unspecified -# 1,7 = Convention Center -# 1,13 = Coffee Shop -# 2,0 = Unspecified Business -# 7,1 Private Residence -#venue_group=7 -#venue_type=1 - -# Homogeneous ESS identifier (optional; dot11HESSID) -# If set, this shall be identifical to one of the BSSIDs in the homogeneous -# ESS and this shall be set to the same value across all BSSs in homogeneous -# ESS. -#hessid=02:03:04:05:06:07 - -# Roaming Consortium List -# Arbitrary number of Roaming Consortium OIs can be configured with each line -# adding a new OI to the list. The first three entries are available through -# Beacon and Probe Response frames. Any additional entry will be available only -# through ANQP queries. Each OI is between 3 and 15 octets and is configured as -# a hexstring. -#roaming_consortium=021122 -#roaming_consortium=2233445566 - -# Venue Name information -# This parameter can be used to configure one or more Venue Name Duples for -# Venue Name ANQP information. Each entry has a two or three character language -# code (ISO-639) separated by colon from the venue name string. -# Note that venue_group and venue_type have to be set for Venue Name -# information to be complete. -#venue_name=eng:Example venue -#venue_name=fin:Esimerkkipaikka -# Alternative format for language:value strings: -# (double quoted string, printf-escaped string) -#venue_name=P"eng:Example\nvenue" - -# Venue URL information -# This parameter can be used to configure one or more Venue URL Duples to -# provide additional information corresponding to Venue Name information. -# Each entry has a Venue Number value separated by colon from the Venue URL -# string. Venue Number indicates the corresponding venue_name entry (1 = 1st -# venue_name, 2 = 2nd venue_name, and so on; 0 = no matching venue_name) -#venue_url=1:http://www.example.com/info-eng -#venue_url=2:http://www.example.com/info-fin - -# Network Authentication Type -# This parameter indicates what type of network authentication is used in the -# network. -# format: [redirect URL] -# Network Authentication Type Indicator values: -# 00 = Acceptance of terms and conditions -# 01 = On-line enrollment supported -# 02 = http/https redirection -# 03 = DNS redirection -#network_auth_type=00 -#network_auth_type=02http://www.example.com/redirect/me/here/ - -# IP Address Type Availability -# format: <1-octet encoded value as hex str> -# (ipv4_type & 0x3f) << 2 | (ipv6_type & 0x3) -# ipv4_type: -# 0 = Address type not available -# 1 = Public IPv4 address available -# 2 = Port-restricted IPv4 address available -# 3 = Single NATed private IPv4 address available -# 4 = Double NATed private IPv4 address available -# 5 = Port-restricted IPv4 address and single NATed IPv4 address available -# 6 = Port-restricted IPv4 address and double NATed IPv4 address available -# 7 = Availability of the address type is not known -# ipv6_type: -# 0 = Address type not available -# 1 = Address type available -# 2 = Availability of the address type not known -#ipaddr_type_availability=14 - -# Domain Name -# format: [,] -#domain_name=example.com,another.example.com,yet-another.example.com - -# 3GPP Cellular Network information -# format: [;][;...] -#anqp_3gpp_cell_net=244,91;310,026;234,56 - -# NAI Realm information -# One or more realm can be advertised. Each nai_realm line adds a new realm to -# the set. These parameters provide information for stations using Interworking -# network selection to allow automatic connection to a network based on -# credentials. -# format: ,[,][,][,...] -# encoding: -# 0 = Realm formatted in accordance with IETF RFC 4282 -# 1 = UTF-8 formatted character string that is not formatted in -# accordance with IETF RFC 4282 -# NAI Realm(s): Semi-colon delimited NAI Realm(s) -# EAP Method: [:<[AuthParam1:Val1]>][<[AuthParam2:Val2]>][...] -# EAP Method types, see: -# http://www.iana.org/assignments/eap-numbers/eap-numbers.xhtml#eap-numbers-4 -# AuthParam (Table 8-188 in IEEE Std 802.11-2012): -# ID 2 = Non-EAP Inner Authentication Type -# 1 = PAP, 2 = CHAP, 3 = MSCHAP, 4 = MSCHAPV2 -# ID 3 = Inner authentication EAP Method Type -# ID 5 = Credential Type -# 1 = SIM, 2 = USIM, 3 = NFC Secure Element, 4 = Hardware Token, -# 5 = Softoken, 6 = Certificate, 7 = username/password, 9 = Anonymous, -# 10 = Vendor Specific -#nai_realm=0,example.com;example.net -# EAP methods EAP-TLS with certificate and EAP-TTLS/MSCHAPv2 with -# username/password -#nai_realm=0,example.org,13[5:6],21[2:4][5:7] - -# Arbitrary ANQP-element configuration -# Additional ANQP-elements with arbitrary values can be defined by specifying -# their contents in raw format as a hexdump of the payload. Note that these -# values will override ANQP-element contents that may have been specified in the -# more higher layer configuration parameters listed above. -# format: anqp_elem=: -# For example, AP Geospatial Location ANQP-element with unknown location: -#anqp_elem=265:0000 -# For example, AP Civic Location ANQP-element with unknown location: -#anqp_elem=266:000000 - -# GAS Address 3 behavior -# 0 = P2P specification (Address3 = AP BSSID) workaround enabled by default -# based on GAS request Address3 -# 1 = IEEE 802.11 standard compliant regardless of GAS request Address3 -# 2 = Force non-compliant behavior (Address3 = AP BSSID for all cases) -#gas_address3=0 - -# QoS Map Set configuration -# -# Comma delimited QoS Map Set in decimal values -# (see IEEE Std 802.11-2012, 8.4.2.97) -# -# format: -# [,],... -# -# There can be up to 21 optional DSCP Exceptions which are pairs of DSCP Value -# (0..63 or 255) and User Priority (0..7). This is followed by eight DSCP Range -# descriptions with DSCP Low Value and DSCP High Value pairs (0..63 or 255) for -# each UP starting from 0. If both low and high value are set to 255, the -# corresponding UP is not used. -# -# default: not set -#qos_map_set=53,2,22,6,8,15,0,7,255,255,16,31,32,39,255,255,40,47,255,255 - -##### Hotspot 2.0 ############################################################# - -# Enable Hotspot 2.0 support -#hs20=1 - -# Disable Downstream Group-Addressed Forwarding (DGAF) -# This can be used to configure a network where no group-addressed frames are -# allowed. The AP will not forward any group-address frames to the stations and -# random GTKs are issued for each station to prevent associated stations from -# forging such frames to other stations in the BSS. -#disable_dgaf=1 - -# OSU Server-Only Authenticated L2 Encryption Network -#osen=1 - -# ANQP Domain ID (0..65535) -# An identifier for a set of APs in an ESS that share the same common ANQP -# information. 0 = Some of the ANQP information is unique to this AP (default). -#anqp_domain_id=1234 - -# Deauthentication request timeout -# If the RADIUS server indicates that the station is not allowed to connect to -# the BSS/ESS, the AP can allow the station some time to download a -# notification page (URL included in the message). This parameter sets that -# timeout in seconds. -#hs20_deauth_req_timeout=60 - -# Operator Friendly Name -# This parameter can be used to configure one or more Operator Friendly Name -# Duples. Each entry has a two or three character language code (ISO-639) -# separated by colon from the operator friendly name string. -#hs20_oper_friendly_name=eng:Example operator -#hs20_oper_friendly_name=fin:Esimerkkioperaattori - -# Connection Capability -# This can be used to advertise what type of IP traffic can be sent through the -# hotspot (e.g., due to firewall allowing/blocking protocols/ports). -# format: :: -# IP Protocol: 1 = ICMP, 6 = TCP, 17 = UDP -# Port Number: 0..65535 -# Status: 0 = Closed, 1 = Open, 2 = Unknown -# Each hs20_conn_capab line is added to the list of advertised tuples. -#hs20_conn_capab=1:0:2 -#hs20_conn_capab=6:22:1 -#hs20_conn_capab=17:5060:0 - -# WAN Metrics -# format: :
:
    :
    :
      : -# WAN Info: B0-B1: Link Status, B2: Symmetric Link, B3: At Capabity -# (encoded as two hex digits) -# Link Status: 1 = Link up, 2 = Link down, 3 = Link in test state -# Downlink Speed: Estimate of WAN backhaul link current downlink speed in kbps; -# 1..4294967295; 0 = unknown -# Uplink Speed: Estimate of WAN backhaul link current uplink speed in kbps -# 1..4294967295; 0 = unknown -# Downlink Load: Current load of downlink WAN connection (scaled to 255 = 100%) -# Uplink Load: Current load of uplink WAN connection (scaled to 255 = 100%) -# Load Measurement Duration: Duration for measuring downlink/uplink load in -# tenths of a second (1..65535); 0 if load cannot be determined -#hs20_wan_metrics=01:8000:1000:80:240:3000 - -# Operating Class Indication -# List of operating classes the BSSes in this ESS use. The Global operating -# classes in Table E-4 of IEEE Std 802.11-2012 Annex E define the values that -# can be used in this. -# format: hexdump of operating class octets -# for example, operating classes 81 (2.4 GHz channels 1-13) and 115 (5 GHz -# channels 36-48): -#hs20_operating_class=5173 - -# Terms and Conditions information -# -# hs20_t_c_filename contains the Terms and Conditions filename that the AP -# indicates in RADIUS Access-Request messages. -#hs20_t_c_filename=terms-and-conditions -# -# hs20_t_c_timestamp contains the Terms and Conditions timestamp that the AP -# indicates in RADIUS Access-Request messages. Usually, this contains the number -# of seconds since January 1, 1970 00:00 UTC showing the time when the file was -# last modified. -#hs20_t_c_timestamp=1234567 -# -# hs20_t_c_server_url contains a template for the Terms and Conditions server -# URL. This template is used to generate the URL for a STA that needs to -# acknowledge Terms and Conditions. Unlike the other hs20_t_c_* parameters, this -# parameter is used on the authentication server, not the AP. -# Macros: -# @1@ = MAC address of the STA (colon separated hex octets) -#hs20_t_c_server_url=https://example.com/t_and_c?addr=@1@&ap=123 - -# OSU and Operator icons -# ::::: -#hs20_icon=32:32:eng:image/png:icon32:/tmp/icon32.png -#hs20_icon=64:64:eng:image/png:icon64:/tmp/icon64.png - -# OSU SSID (see ssid2 for format description) -# This is the SSID used for all OSU connections to all the listed OSU Providers. -#osu_ssid="example" - -# OSU Providers -# One or more sets of following parameter. Each OSU provider is started by the -# mandatory osu_server_uri item. The other parameters add information for the -# last added OSU provider. osu_nai specifies the OSU_NAI value for OSEN -# authentication when using a standalone OSU BSS. osu_nai2 specifies the OSU_NAI -# value for OSEN authentication when using a shared BSS (Single SSID) for OSU. -# -#osu_server_uri=https://example.com/osu/ -#osu_friendly_name=eng:Example operator -#osu_friendly_name=fin:Esimerkkipalveluntarjoaja -#osu_nai=anonymous@example.com -#osu_nai2=anonymous@example.com -#osu_method_list=1 0 -#osu_icon=icon32 -#osu_icon=icon64 -#osu_service_desc=eng:Example services -#osu_service_desc=fin:Esimerkkipalveluja -# -#osu_server_uri=... - -# Operator Icons -# Operator icons are specified using references to the hs20_icon entries -# (Name subfield). This information, if present, is advertsised in the -# Operator Icon Metadata ANQO-element. -#operator_icon=icon32 -#operator_icon=icon64 - -##### Multiband Operation (MBO) ############################################### -# -# MBO enabled -# 0 = disabled (default) -# 1 = enabled -#mbo=1 -# -# Cellular data connection preference -# 0 = Excluded - AP does not want STA to use the cellular data connection -# 1 = AP prefers the STA not to use cellular data connection -# 255 = AP prefers the STA to use cellular data connection -#mbo_cell_data_conn_pref=1 - -##### Optimized Connectivity Experience (OCE) ################################# -# -# Enable OCE specific features (bitmap) -# BIT(0) - Reserved -# Set BIT(1) (= 2) to enable OCE in STA-CFON mode -# Set BIT(2) (= 4) to enable OCE in AP mode -# Default is 0 = OCE disabled -#oce=0 - -# RSSI-based association rejection -# -# Reject STA association if RSSI is below given threshold (in dBm) -# Allowed range: -60 to -90 dBm; default = 0 (rejection disabled) -# Note: This rejection happens based on a signal strength detected while -# receiving a single frame and as such, there is significant risk of the value -# not being accurate and this resulting in valid stations being rejected. As -# such, this functionality is not recommended to be used for purposes other than -# testing. -#rssi_reject_assoc_rssi=-75 -# -# Association retry delay in seconds allowed by the STA if RSSI has not met the -# threshold (range: 0..255, default=30). -#rssi_reject_assoc_timeout=30 - -# Ignore Probe Request frames if RSSI is below given threshold (in dBm) -# Allowed range: -60 to -90 dBm; default = 0 (rejection disabled) -#rssi_ignore_probe_request=-75 - -##### Fast Session Transfer (FST) support ##################################### -# -# The options in this section are only available when the build configuration -# option CONFIG_FST is set while compiling hostapd. They allow this interface -# to be a part of FST setup. -# -# FST is the transfer of a session from a channel to another channel, in the -# same or different frequency bands. -# -# For detals, see IEEE Std 802.11ad-2012. - -# Identifier of an FST Group the interface belongs to. -#fst_group_id=bond0 - -# Interface priority within the FST Group. -# Announcing a higher priority for an interface means declaring it more -# preferable for FST switch. -# fst_priority is in 1..255 range with 1 being the lowest priority. -#fst_priority=100 - -# Default LLT value for this interface in milliseconds. The value used in case -# no value provided during session setup. Default is 50 ms. -# fst_llt is in 1..4294967 range (due to spec limitation, see 10.32.2.2 -# Transitioning between states). -#fst_llt=100 - -##### Radio measurements / location ########################################### - -# The content of a LCI measurement subelement -#lci= - -# The content of a location civic measurement subelement -#civic= - -# Enable neighbor report via radio measurements -#rrm_neighbor_report=1 - -# Enable beacon report via radio measurements -#rrm_beacon_report=1 - -# Publish fine timing measurement (FTM) responder functionality -# This parameter only controls publishing via Extended Capabilities element. -# Actual functionality is managed outside hostapd. -#ftm_responder=0 - -# Publish fine timing measurement (FTM) initiator functionality -# This parameter only controls publishing via Extended Capabilities element. -# Actual functionality is managed outside hostapd. -#ftm_initiator=0 -# -# Stationary AP config indicates that the AP doesn't move hence location data -# can be considered as always up to date. If configured, LCI data will be sent -# as a radio measurement even if the request doesn't contain a max age element -# that allows sending of such data. Default: 0. -#stationary_ap=0 - -# Enable reduced neighbor reporting (RNR) -#rnr=0 - -##### Airtime policy configuration ########################################### - -# Set the airtime policy operating mode: -# 0 = disabled (default) -# 1 = static config -# 2 = per-BSS dynamic config -# 3 = per-BSS limit mode -#airtime_mode=0 - -# Interval (in milliseconds) to poll the kernel for updated station activity in -# dynamic and limit modes -#airtime_update_interval=200 - -# Static configuration of station weights (when airtime_mode=1). Kernel default -# weight is 256; set higher for larger airtime share, lower for smaller share. -# Each entry is a MAC address followed by a weight. -#airtime_sta_weight=02:01:02:03:04:05 256 -#airtime_sta_weight=02:01:02:03:04:06 512 - -# Per-BSS airtime weight. In multi-BSS mode, set for each BSS and hostapd will -# configure station weights to enforce the correct ratio between BSS weights -# depending on the number of active stations. The *ratios* between different -# BSSes is what's important, not the absolute numbers. -# Must be set for all BSSes if airtime_mode=2 or 3, has no effect otherwise. -#airtime_bss_weight=1 - -# Whether the current BSS should be limited (when airtime_mode=3). -# -# If set, the BSS weight ratio will be applied in the case where the current BSS -# would exceed the share defined by the BSS weight ratio. E.g., if two BSSes are -# set to the same weights, and one is set to limited, the limited BSS will get -# no more than half the available airtime, but if the non-limited BSS has more -# stations active, that *will* be allowed to exceed its half of the available -# airtime. -#airtime_bss_limit=1 - -##### EDMG support ############################################################ -# -# Enable EDMG capability for AP mode in the 60 GHz band. Default value is false. -# To configure channel bonding for an EDMG AP use edmg_channel below. -# If enable_edmg is set and edmg_channel is not set, EDMG CB1 will be -# configured. -#enable_edmg=1 -# -# Configure channel bonding for AP mode in the 60 GHz band. -# This parameter is relevant only if enable_edmg is set. -# Default value is 0 (no channel bonding). -#edmg_channel=9 - -##### TESTING OPTIONS ######################################################### -# -# The options in this section are only available when the build configuration -# option CONFIG_TESTING_OPTIONS is set while compiling hostapd. They allow -# testing some scenarios that are otherwise difficult to reproduce. -# -# Ignore probe requests sent to hostapd with the given probability, must be a -# floating point number in the range [0, 1). -#ignore_probe_probability=0.0 -# -# Ignore authentication frames with the given probability -#ignore_auth_probability=0.0 -# -# Ignore association requests with the given probability -#ignore_assoc_probability=0.0 -# -# Ignore reassociation requests with the given probability -#ignore_reassoc_probability=0.0 -# -# Corrupt Key MIC in GTK rekey EAPOL-Key frames with the given probability -#corrupt_gtk_rekey_mic_probability=0.0 -# -# Include only ECSA IE without CSA IE where possible -# (channel switch operating class is needed) -#ecsa_ie_only=0 - -##### Multiple BSSID support ################################################## -# -# Above configuration is using the default interface (wlan#, or multi-SSID VLAN -# interfaces). Other BSSIDs can be added by using separator 'bss' with -# default interface name to be allocated for the data packets of the new BSS. -# -# hostapd will generate BSSID mask based on the BSSIDs that are -# configured. hostapd will verify that dev_addr & MASK == dev_addr. If this is -# not the case, the MAC address of the radio must be changed before starting -# hostapd (ifconfig wlan0 hw ether ). If a BSSID is configured for -# every secondary BSS, this limitation is not applied at hostapd and other -# masks may be used if the driver supports them (e.g., swap the locally -# administered bit) -# -# BSSIDs are assigned in order to each BSS, unless an explicit BSSID is -# specified using the 'bssid' parameter. -# If an explicit BSSID is specified, it must be chosen such that it: -# - results in a valid MASK that covers it and the dev_addr -# - is not the same as the MAC address of the radio -# - is not the same as any other explicitly specified BSSID -# -# Alternatively, the 'use_driver_iface_addr' parameter can be used to request -# hostapd to use the driver auto-generated interface address (e.g., to use the -# exact MAC addresses allocated to the device). -# -# Not all drivers support multiple BSSes. The exact mechanism for determining -# the driver capabilities is driver specific. With the current (i.e., a recent -# kernel) drivers using nl80211, this information can be checked with "iw list" -# (search for "valid interface combinations"). -# -# Please note that hostapd uses some of the values configured for the first BSS -# as the defaults for the following BSSes. However, it is recommended that all -# BSSes include explicit configuration of all relevant configuration items. -# -#bss=wlan0_0 -#ssid=test2 -# most of the above items can be used here (apart from radio interface specific -# items, like channel) +# Use GCMP-128 +#rsn_pairwise=GCMP-128 +rsn_pairwise=CCMP -#bss=wlan0_1 -#bssid=00:13:10:95:fe:0b -# ... +# Enable WPA3-SAE with mandatory Management Frame Protection +sae_require_mfp=1 \ No newline at end of file diff --git a/APs/config/wpa3/hostapd_downgrade.conf.tmp b/APs/config/wpa3/hostapd_downgrade.conf.tmp index c9cf407..692da94 100644 --- a/APs/config/wpa3/hostapd_downgrade.conf.tmp +++ b/APs/config/wpa3/hostapd_downgrade.conf.tmp @@ -1,3108 +1,48 @@ ##### hostapd configuration file ############################################## -# Empty lines and lines starting with # are ignored - -# AP netdevice name (without 'ap' postfix, i.e., wlan0 uses wlan0ap for -# management frames with the Host AP driver); wlan0 with many nl80211 drivers -# Note: This attribute can be overridden by the values supplied with the '-i' -# command line parameter. interface=$WLAN_DOWNGRADE - -# In case of atheros and nl80211 driver interfaces, an additional -# configuration parameter, bridge, may be used to notify hostapd if the -# interface is included in a bridge. This parameter is not used with Host AP -# driver. If the bridge parameter is not set, the drivers will automatically -# figure out the bridge interface (assuming sysfs is enabled and mounted to -# /sys) and this parameter may not be needed. -# -# For nl80211, this parameter can be used to request the AP interface to be -# added to the bridge automatically (brctl may refuse to do this before hostapd -# has been started to change the interface mode). If needed, the bridge -# interface is also created. -#bridge=br0 - -# Driver interface type (hostap/wired/none/nl80211/bsd); -# default: hostap). nl80211 is used with all Linux mac80211 drivers. -# Use driver=none if building hostapd as a standalone RADIUS server that does -# not control any wireless/wired driver. -# driver=hostap - -# Driver interface parameters (mainly for development testing use) -# driver_params= - -# hostapd event logger configuration -# -# Two output method: syslog and stdout (only usable if not forking to -# background). -# -# Module bitfield (ORed bitfield of modules that will be logged; -1 = all -# modules): -# bit 0 (1) = IEEE 802.11 -# bit 1 (2) = IEEE 802.1X -# bit 2 (4) = RADIUS -# bit 3 (8) = WPA -# bit 4 (16) = driver interface -# bit 6 (64) = MLME -# -# Levels (minimum value for logged events): -# 0 = verbose debugging -# 1 = debugging -# 2 = informational messages -# 3 = notification -# 4 = warning -# logger_syslog=-1 logger_syslog_level=2 logger_stdout=-1 logger_stdout_level=2 - -# Interface for separate control program. If this is specified, hostapd -# will create this directory and a UNIX domain socket for listening to requests -# from external programs (CLI/GUI, etc.) for status information and -# configuration. The socket file will be named based on the interface name, so -# multiple hostapd processes/interfaces can be run at the same time if more -# than one interface is used. -# /var/run/hostapd is the recommended directory for sockets and by default, -# hostapd_cli will use it when trying to connect with hostapd. ctrl_interface=/var/run/hostapd - -# Access control for the control interface can be configured by setting the -# directory to allow only members of a group to use sockets. This way, it is -# possible to run hostapd as root (since it needs to change network -# configuration and open raw sockets) and still allow GUI/CLI components to be -# run as non-root users. However, since the control interface can be used to -# change the network configuration, this access needs to be protected in many -# cases. By default, hostapd is configured to use gid 0 (root). If you -# want to allow non-root users to use the control interface, add a new group -# and change this value to match with that group. Add users that should have -# control interface access to this group. -# -# This variable can be a group name or gid. -#ctrl_interface_group=wheel ctrl_interface_group=0 - - -##### IEEE 802.11 related configuration ####################################### - -# SSID to be used in IEEE 802.11 management frames ssid=wifi-IT -# Alternative formats for configuring SSID -# (double quoted string, hexdump, printf-escaped string) -#ssid2="test" -#ssid2=74657374 -#ssid2=P"hello\nthere" - -# UTF-8 SSID: Whether the SSID is to be interpreted using UTF-8 encoding -#utf8_ssid=1 - -# Country code (ISO/IEC 3166-1). Used to set regulatory domain. -# Set as needed to indicate country in which device is operating. -# This can limit available channels and transmit power. -# These two octets are used as the first two octets of the Country String -# (dot11CountryString) -#country_code=US - -# The third octet of the Country String (dot11CountryString) -# This parameter is used to set the third octet of the country string. -# -# All environments of the current frequency band and country (default) -#country3=0x20 -# Outdoor environment only -#country3=0x4f -# Indoor environment only -#country3=0x49 -# Noncountry entity (country_code=XX) -#country3=0x58 -# IEEE 802.11 standard Annex E table indication: 0x01 .. 0x1f -# Annex E, Table E-4 (Global operating classes) -#country3=0x04 - -# Enable IEEE 802.11d. This advertises the country_code and the set of allowed -# channels and transmit power levels based on the regulatory limits. The -# country_code setting must be configured with the correct country for -# IEEE 802.11d functions. -# (default: 0 = disabled) -#ieee80211d=1 - -# Enable IEEE 802.11h. This enables radar detection and DFS support if -# available. DFS support is required on outdoor 5 GHz channels in most countries -# of the world. This can be used only with ieee80211d=1. -# (default: 0 = disabled) -#ieee80211h=1 - -# Add Power Constraint element to Beacon and Probe Response frames -# This config option adds Power Constraint element when applicable and Country -# element is added. Power Constraint element is required by Transmit Power -# Control. This can be used only with ieee80211d=1. -# Valid values are 0..255. -#local_pwr_constraint=3 - -# Set Spectrum Management subfield in the Capability Information field. -# This config option forces the Spectrum Management bit to be set. When this -# option is not set, the value of the Spectrum Management bit depends on whether -# DFS or TPC is required by regulatory authorities. This can be used only with -# ieee80211d=1 and local_pwr_constraint configured. -#spectrum_mgmt_required=1 - -# Operation mode (a = IEEE 802.11a (5 GHz), b = IEEE 802.11b (2.4 GHz), -# g = IEEE 802.11g (2.4 GHz), ad = IEEE 802.11ad (60 GHz); a/g options are used -# with IEEE 802.11n (HT), too, to specify band). For IEEE 802.11ac (VHT), this -# needs to be set to hw_mode=a. For IEEE 802.11ax (HE) on 6 GHz this needs -# to be set to hw_mode=a. When using ACS (see channel parameter), a -# special value "any" can be used to indicate that any support band can be used. -# This special case is currently supported only with drivers with which -# offloaded ACS is used. -# Default: IEEE 802.11b hw_mode=g - -# Channel number (IEEE 802.11) -# (default: 0, i.e., not set) -# Please note that some drivers do not use this value from hostapd and the -# channel will need to be configured separately with iwconfig. -# -# If CONFIG_ACS build option is enabled, the channel can be selected -# automatically at run time by setting channel=acs_survey or channel=0, both of -# which will enable the ACS survey based algorithm. channel=11 - -# Global operating class (IEEE 802.11, Annex E, Table E-4) -# This option allows hostapd to specify the operating class of the channel -# configured with the channel parameter. channel and op_class together can -# uniquely identify channels across different bands, including the 6 GHz band. -#op_class=131 - -# ACS tuning - Automatic Channel Selection -# See: https://wireless.wiki.kernel.org/en/users/documentation/acs -# -# You can customize the ACS survey algorithm with following variables: -# -# acs_num_scans requirement is 1..100 - number of scans to be performed that -# are used to trigger survey data gathering of an underlying device driver. -# Scans are passive and typically take a little over 100ms (depending on the -# driver) on each available channel for given hw_mode. Increasing this value -# means sacrificing startup time and gathering more data wrt channel -# interference that may help choosing a better channel. This can also help fine -# tune the ACS scan time in case a driver has different scan dwell times. -# -# acs_chan_bias is a space-separated list of : pairs. It can be -# used to increase (or decrease) the likelihood of a specific channel to be -# selected by the ACS algorithm. The total interference factor for each channel -# gets multiplied by the specified bias value before finding the channel with -# the lowest value. In other words, values between 0.0 and 1.0 can be used to -# make a channel more likely to be picked while values larger than 1.0 make the -# specified channel less likely to be picked. This can be used, e.g., to prefer -# the commonly used 2.4 GHz band channels 1, 6, and 11 (which is the default -# behavior on 2.4 GHz band if no acs_chan_bias parameter is specified). -# -# Defaults: -#acs_num_scans=5 -#acs_chan_bias=1:0.8 6:0.8 11:0.8 - -# Channel list restriction. This option allows hostapd to select one of the -# provided channels when a channel should be automatically selected. -# Channel list can be provided as range using hyphen ('-') or individual -# channels can be specified by space (' ') separated values -# Default: all channels allowed in selected hw_mode -#chanlist=100 104 108 112 116 -#chanlist=1 6 11-13 - -# Frequency list restriction. This option allows hostapd to select one of the -# provided frequencies when a frequency should be automatically selected. -# Frequency list can be provided as range using hyphen ('-') or individual -# frequencies can be specified by comma (',') separated values -# Default: all frequencies allowed in selected hw_mode -#freqlist=2437,5955,5975 -#freqlist=2437,5985-6105 - -# Exclude DFS channels from ACS -# This option can be used to exclude all DFS channels from the ACS channel list -# in cases where the driver supports DFS channels. -#acs_exclude_dfs=1 - -# Include only preferred scan channels from 6 GHz band for ACS -# This option can be used to include only preferred scan channels in the 6 GHz -# band. This can be useful in particular for devices that operate only a 6 GHz -# BSS without a collocated 2.4/5 GHz BSS. -# Default behavior is to include all PSC and non-PSC channels. -#acs_exclude_6ghz_non_psc=1 - -# Enable background radar feature -# This feature allows CAC to be run on dedicated radio RF chains while the -# radio(s) are otherwise running normal AP activities on other channels. -# This requires that the driver and the radio support it before feature will -# actually be enabled, i.e., this parameter value is ignored with drivers that -# do not advertise support for the capability. -# 0: Leave disabled (default) -# 1: Enable it. -#enable_background_radar=1 - -# Set minimum permitted max TX power (in dBm) for ACS and DFS channel selection. -# (default 0, i.e., not constraint) -#min_tx_power=20 - -# Beacon interval in kus (1.024 ms) (default: 100; range 15..65535) beacon_int=100 - -# DTIM (delivery traffic information message) period (range 1..255): -# number of beacons between DTIMs (1 = every beacon includes DTIM element) -# (default: 2) dtim_period=2 - -# Maximum number of stations allowed in station table. New stations will be -# rejected after the station table is full. IEEE 802.11 has a limit of 2007 -# different association IDs, so this number should not be larger than that. -# (default: 2007) max_num_sta=255 - -# RTS/CTS threshold; -1 = disabled (default); range -1..65535 -# If this field is not included in hostapd.conf, hostapd will not control -# RTS threshold and 'iwconfig wlan# rts ' can be used to set it. rts_threshold=-1 - -# Fragmentation threshold; -1 = disabled (default); range -1, 256..2346 -# If this field is not included in hostapd.conf, hostapd will not control -# fragmentation threshold and 'iwconfig wlan# frag ' can be used to set -# it. fragm_threshold=-1 - -# Rate configuration -# Default is to enable all rates supported by the hardware. This configuration -# item allows this list be filtered so that only the listed rates will be left -# in the list. If the list is empty, all rates are used. This list can have -# entries that are not in the list of rates the hardware supports (such entries -# are ignored). The entries in this list are in 100 kbps, i.e., 11 Mbps = 110. -# If this item is present, at least one rate have to be matching with the rates -# hardware supports. -# default: use the most common supported rate setting for the selected -# hw_mode (i.e., this line can be removed from configuration file in most -# cases) -#supported_rates=10 20 55 110 60 90 120 180 240 360 480 540 - -# Basic rate set configuration -# List of rates (in 100 kbps) that are included in the basic rate set. -# If this item is not included, usually reasonable default set is used. -#basic_rates=10 20 -#basic_rates=10 20 55 110 -#basic_rates=60 120 240 - -# Beacon frame TX rate configuration -# This sets the TX rate that is used to transmit Beacon frames. If this item is -# not included, the driver default rate (likely lowest rate) is used. -# Legacy (CCK/OFDM rates): -# beacon_rate= -# HT: -# beacon_rate=ht: -# VHT: -# beacon_rate=vht: -# HE: -# beacon_rate=he: -# -# For example, beacon_rate=10 for 1 Mbps or beacon_rate=60 for 6 Mbps (OFDM). -#beacon_rate=10 - -# Short Preamble -# This parameter can be used to enable optional use of short preamble for -# frames sent at 2 Mbps, 5.5 Mbps, and 11 Mbps to improve network performance. -# This applies only to IEEE 802.11b-compatible networks and this should only be -# enabled if the local hardware supports use of short preamble. If any of the -# associated STAs do not support short preamble, use of short preamble will be -# disabled (and enabled when such STAs disassociate) dynamically. -# 0 = do not allow use of short preamble (default) -# 1 = allow use of short preamble -#preamble=1 - -# Station MAC address -based authentication -# Please note that this kind of access control requires a driver that uses -# hostapd to take care of management frame processing and as such, this can be -# used with driver=hostap or driver=nl80211, but not with driver=atheros. -# 0 = accept unless in deny list -# 1 = deny unless in accept list -# 2 = use external RADIUS server (accept/deny lists are searched first) macaddr_acl=0 - -# Accept/deny lists are read from separate files (containing list of -# MAC addresses, one per line). Use absolute path name to make sure that the -# files can be read on SIGHUP configuration reloads. -#accept_mac_file=/etc/hostapd.accept -#deny_mac_file=/etc/hostapd.deny - -# IEEE 802.11 specifies two authentication algorithms. hostapd can be -# configured to allow both of these or only one. Open system authentication -# should be used with IEEE 802.1X. -# Bit fields of allowed authentication algorithms: -# bit 0 = Open System Authentication -# bit 1 = Shared Key Authentication (requires WEP) auth_algs=3 - -# Send empty SSID in beacons and ignore probe request frames that do not -# specify full SSID, i.e., require stations to know SSID. -# default: disabled (0) -# 1 = send empty (length=0) SSID in beacon and ignore probe request for -# broadcast SSID -# 2 = clear SSID (ASCII 0), but keep the original length (this may be required -# with some clients that do not support empty SSID) and ignore probe -# requests for broadcast SSID ignore_broadcast_ssid=0 - -# Do not reply to broadcast Probe Request frames from unassociated STA if there -# is no room for additional stations (max_num_sta). This can be used to -# discourage a STA from trying to associate with this AP if the association -# would be rejected due to maximum STA limit. -# Default: 0 (disabled) -#no_probe_resp_if_max_sta=0 - -# Additional vendor specific elements for Beacon and Probe Response frames -# This parameter can be used to add additional vendor specific element(s) into -# the end of the Beacon and Probe Response frames. The format for these -# element(s) is a hexdump of the raw information elements (id+len+payload for -# one or more elements) -#vendor_elements=dd0411223301 - -# Additional vendor specific elements for (Re)Association Response frames -# This parameter can be used to add additional vendor specific element(s) into -# the end of the (Re)Association Response frames. The format for these -# element(s) is a hexdump of the raw information elements (id+len+payload for -# one or more elements) -#assocresp_elements=dd0411223301 - -# TX queue parameters (EDCF / bursting) -# tx_queue__ -# queues: data0, data1, data2, data3 -# (data0 is the highest priority queue) -# parameters: -# aifs: AIFS (default 2) -# cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023, 2047, 4095, 8191, -# 16383, 32767) -# cwmax: cwMax (same values as cwMin, cwMax >= cwMin) -# burst: maximum length (in milliseconds with precision of up to 0.1 ms) for -# bursting -# -# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): -# These parameters are used by the access point when transmitting frames -# to the clients. -# -# Low priority / AC_BK = background -#tx_queue_data3_aifs=7 -#tx_queue_data3_cwmin=15 -#tx_queue_data3_cwmax=1023 -#tx_queue_data3_burst=0 -# Note: for IEEE 802.11b mode: cWmin=31 cWmax=1023 burst=0 -# -# Normal priority / AC_BE = best effort -#tx_queue_data2_aifs=3 -#tx_queue_data2_cwmin=15 -#tx_queue_data2_cwmax=63 -#tx_queue_data2_burst=0 -# Note: for IEEE 802.11b mode: cWmin=31 cWmax=127 burst=0 -# -# High priority / AC_VI = video -#tx_queue_data1_aifs=1 -#tx_queue_data1_cwmin=7 -#tx_queue_data1_cwmax=15 -#tx_queue_data1_burst=3.0 -# Note: for IEEE 802.11b mode: cWmin=15 cWmax=31 burst=6.0 -# -# Highest priority / AC_VO = voice -#tx_queue_data0_aifs=1 -#tx_queue_data0_cwmin=3 -#tx_queue_data0_cwmax=7 -#tx_queue_data0_burst=1.5 -# Note: for IEEE 802.11b mode: cWmin=7 cWmax=15 burst=3.3 - -# 802.1D Tag (= UP) to AC mappings -# WMM specifies following mapping of data frames to different ACs. This mapping -# can be configured using Linux QoS/tc and sch_pktpri.o module. -# 802.1D Tag 802.1D Designation Access Category WMM Designation -# 1 BK AC_BK Background -# 2 - AC_BK Background -# 0 BE AC_BE Best Effort -# 3 EE AC_BE Best Effort -# 4 CL AC_VI Video -# 5 VI AC_VI Video -# 6 VO AC_VO Voice -# 7 NC AC_VO Voice -# Data frames with no priority information: AC_BE -# Management frames: AC_VO -# PS-Poll frames: AC_BE - -# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): -# for 802.11a or 802.11g networks -# These parameters are sent to WMM clients when they associate. -# The parameters will be used by WMM clients for frames transmitted to the -# access point. -# -# note - txop_limit is in units of 32microseconds -# note - acm is admission control mandatory flag. 0 = admission control not -# required, 1 = mandatory -# note - Here cwMin and cmMax are in exponent form. The actual cw value used -# will be (2^n)-1 where n is the value given here. The allowed range for these -# wmm_ac_??_{cwmin,cwmax} is 0..15 with cwmax >= cwmin. -# wmm_enabled=1 -# -# WMM-PS Unscheduled Automatic Power Save Delivery [U-APSD] -# Enable this flag if U-APSD supported outside hostapd (eg., Firmware/driver) -#uapsd_advertisement_enabled=1 -# -# Low priority / AC_BK = background wmm_ac_bk_cwmin=4 wmm_ac_bk_cwmax=10 wmm_ac_bk_aifs=7 wmm_ac_bk_txop_limit=0 wmm_ac_bk_acm=0 -# Note: for IEEE 802.11b mode: cWmin=5 cWmax=10 -# -# Normal priority / AC_BE = best effort wmm_ac_be_aifs=3 wmm_ac_be_cwmin=4 wmm_ac_be_cwmax=10 wmm_ac_be_txop_limit=0 wmm_ac_be_acm=0 -# Note: for IEEE 802.11b mode: cWmin=5 cWmax=7 -# -# High priority / AC_VI = video wmm_ac_vi_aifs=2 wmm_ac_vi_cwmin=3 wmm_ac_vi_cwmax=4 wmm_ac_vi_txop_limit=94 wmm_ac_vi_acm=0 -# Note: for IEEE 802.11b mode: cWmin=4 cWmax=5 txop_limit=188 -# -# Highest priority / AC_VO = voice wmm_ac_vo_aifs=2 wmm_ac_vo_cwmin=2 wmm_ac_vo_cwmax=3 wmm_ac_vo_txop_limit=47 wmm_ac_vo_acm=0 -# Note: for IEEE 802.11b mode: cWmin=3 cWmax=4 burst=102 - -# Enable Multi-AP functionality -# 0 = disabled (default) -# 1 = AP support backhaul BSS -# 2 = AP support fronthaul BSS -# 3 = AP supports both backhaul BSS and fronthaul BSS -#multi_ap=0 - -# Static WEP key configuration -# -# The key number to use when transmitting. -# It must be between 0 and 3, and the corresponding key must be set. -# default: not set -#wep_default_key=0 -# The WEP keys to use. -# A key may be a quoted string or unquoted hexadecimal digits. -# The key length should be 5, 13, or 16 characters, or 10, 26, or 32 -# digits, depending on whether 40-bit (64-bit), 104-bit (128-bit), or -# 128-bit (152-bit) WEP is used. -# Only the default key must be supplied; the others are optional. -# default: not set -#wep_key0=123456789a -#wep_key1="vwxyz" -#wep_key2=0102030405060708090a0b0c0d -#wep_key3=".2.4.6.8.0.23" - -# Station inactivity limit -# -# If a station does not send anything in ap_max_inactivity seconds, an -# empty data frame is sent to it in order to verify whether it is -# still in range. If this frame is not ACKed, the station will be -# disassociated and then deauthenticated. This feature is used to -# clear station table of old entries when the STAs move out of the -# range. -# -# The station can associate again with the AP if it is still in range; -# this inactivity poll is just used as a nicer way of verifying -# inactivity; i.e., client will not report broken connection because -# disassociation frame is not sent immediately without first polling -# the STA with a data frame. -# default: 300 (i.e., 5 minutes) -#ap_max_inactivity=300 -# -# The inactivity polling can be disabled to disconnect stations based on -# inactivity timeout so that idle stations are more likely to be disconnected -# even if they are still in range of the AP. This can be done by setting -# skip_inactivity_poll to 1 (default 0). -#skip_inactivity_poll=0 - -# Disassociate stations based on excessive transmission failures or other -# indications of connection loss. This depends on the driver capabilities and -# may not be available with all drivers. -#disassoc_low_ack=1 - -# Maximum allowed Listen Interval (how many Beacon periods STAs are allowed to -# remain asleep). Default: 65535 (no limit apart from field size) -#max_listen_interval=100 - -# WDS (4-address frame) mode with per-station virtual interfaces -# (only supported with driver=nl80211) -# This mode allows associated stations to use 4-address frames to allow layer 2 -# bridging to be used. -#wds_sta=1 - -# If bridge parameter is set, the WDS STA interface will be added to the same -# bridge by default. This can be overridden with the wds_bridge parameter to -# use a separate bridge. -#wds_bridge=wds-br0 - -# Start the AP with beaconing disabled by default. -#start_disabled=0 - -# Client isolation can be used to prevent low-level bridging of frames between -# associated stations in the BSS. By default, this bridging is allowed. -#ap_isolate=1 - -# BSS Load update period (in BUs) -# This field is used to enable and configure adding a BSS Load element into -# Beacon and Probe Response frames. -#bss_load_update_period=50 - -# Channel utilization averaging period (in BUs) -# This field is used to enable and configure channel utilization average -# calculation with bss_load_update_period. This should be in multiples of -# bss_load_update_period for more accurate calculation. -#chan_util_avg_period=600 - -# Fixed BSS Load value for testing purposes -# This field can be used to configure hostapd to add a fixed BSS Load element -# into Beacon and Probe Response frames for testing purposes. The format is -# :: -#bss_load_test=12:80:20000 - -# Multicast to unicast conversion -# Request that the AP will do multicast-to-unicast conversion for ARP, IPv4, and -# IPv6 frames (possibly within 802.1Q). If enabled, such frames are to be sent -# to each station separately, with the DA replaced by their own MAC address -# rather than the group address. -# -# Note that this may break certain expectations of the receiver, such as the -# ability to drop unicast IP packets received within multicast L2 frames, or the -# ability to not send ICMP destination unreachable messages for packets received -# in L2 multicast (which is required, but the receiver can't tell the difference -# if this new option is enabled). -# -# This also doesn't implement the 802.11 DMS (directed multicast service). -# -#multicast_to_unicast=0 - -# Send broadcast Deauthentication frame on AP start/stop -# Default: 1 (enabled) -#broadcast_deauth=1 - -# Get notifications for received Management frames on control interface -# Default: 0 (disabled) -#notify_mgmt_frames=0 - -##### IEEE 802.11n related configuration ###################################### - -# ieee80211n: Whether IEEE 802.11n (HT) is enabled -# 0 = disabled (default) -# 1 = enabled -# Note: You will also need to enable WMM for full HT functionality. -# Note: hw_mode=g (2.4 GHz) and hw_mode=a (5 GHz) is used to specify the band. -#ieee80211n=1 - -# disable_11n: Boolean (0/1) to disable HT for a specific BSS -#disable_11n=0 - -# ht_capab: HT capabilities (list of flags) -# LDPC coding capability: [LDPC] = supported -# Supported channel width set: [HT40-] = both 20 MHz and 40 MHz with secondary -# channel below the primary channel; [HT40+] = both 20 MHz and 40 MHz -# with secondary channel above the primary channel -# (20 MHz only if neither is set) -# Note: There are limits on which channels can be used with HT40- and -# HT40+. Following table shows the channels that may be available for -# HT40- and HT40+ use per IEEE 802.11n Annex J: -# freq HT40- HT40+ -# 2.4 GHz 5-13 1-7 (1-9 in Europe/Japan) -# 5 GHz 40,48,56,64 36,44,52,60 -# (depending on the location, not all of these channels may be available -# for use) -# Please note that 40 MHz channels may switch their primary and secondary -# channels if needed or creation of 40 MHz channel maybe rejected based -# on overlapping BSSes. These changes are done automatically when hostapd -# is setting up the 40 MHz channel. -# HT-greenfield: [GF] (disabled if not set) -# Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set) -# Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set) -# Tx STBC: [TX-STBC] (disabled if not set) -# Rx STBC: [RX-STBC1] (one spatial stream), [RX-STBC12] (one or two spatial -# streams), or [RX-STBC123] (one, two, or three spatial streams); Rx STBC -# disabled if none of these set -# HT-delayed Block Ack: [DELAYED-BA] (disabled if not set) -# Maximum A-MSDU length: [MAX-AMSDU-7935] for 7935 octets (3839 octets if not -# set) -# DSSS/CCK Mode in 40 MHz: [DSSS_CCK-40] = allowed (not allowed if not set) -# 40 MHz intolerant [40-INTOLERANT] (not advertised if not set) -# L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set) -#ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40] - -# Require stations to support HT PHY (reject association if they do not) -#require_ht=1 - -# If set non-zero, require stations to perform scans of overlapping -# channels to test for stations which would be affected by 40 MHz traffic. -# This parameter sets the interval in seconds between these scans. Setting this -# to non-zero allows 2.4 GHz band AP to move dynamically to a 40 MHz channel if -# no co-existence issues with neighboring devices are found. -#obss_interval=0 - -##### IEEE 802.11ac related configuration ##################################### - -# ieee80211ac: Whether IEEE 802.11ac (VHT) is enabled -# 0 = disabled (default) -# 1 = enabled -# Note: You will also need to enable WMM for full VHT functionality. -# Note: hw_mode=a is used to specify that 5 GHz band is used with VHT. -#ieee80211ac=1 - -# disable_11ac: Boolean (0/1) to disable VHT for a specific BSS -#disable_11ac=0 - -# vht_capab: VHT capabilities (list of flags) -# -# vht_max_mpdu_len: [MAX-MPDU-7991] [MAX-MPDU-11454] -# Indicates maximum MPDU length -# 0 = 3895 octets (default) -# 1 = 7991 octets -# 2 = 11454 octets -# 3 = reserved -# -# supported_chan_width: [VHT160] [VHT160-80PLUS80] -# Indicates supported Channel widths -# 0 = 160 MHz & 80+80 channel widths are not supported (default) -# 1 = 160 MHz channel width is supported -# 2 = 160 MHz & 80+80 channel widths are supported -# 3 = reserved -# -# Rx LDPC coding capability: [RXLDPC] -# Indicates support for receiving LDPC coded pkts -# 0 = Not supported (default) -# 1 = Supported -# -# Short GI for 80 MHz: [SHORT-GI-80] -# Indicates short GI support for reception of packets transmitted with TXVECTOR -# params format equal to VHT and CBW = 80Mhz -# 0 = Not supported (default) -# 1 = Supported -# -# Short GI for 160 MHz: [SHORT-GI-160] -# Indicates short GI support for reception of packets transmitted with TXVECTOR -# params format equal to VHT and CBW = 160Mhz -# 0 = Not supported (default) -# 1 = Supported -# -# Tx STBC: [TX-STBC-2BY1] -# Indicates support for the transmission of at least 2x1 STBC -# 0 = Not supported (default) -# 1 = Supported -# -# Rx STBC: [RX-STBC-1] [RX-STBC-12] [RX-STBC-123] [RX-STBC-1234] -# Indicates support for the reception of PPDUs using STBC -# 0 = Not supported (default) -# 1 = support of one spatial stream -# 2 = support of one and two spatial streams -# 3 = support of one, two and three spatial streams -# 4 = support of one, two, three and four spatial streams -# 5,6,7 = reserved -# -# SU Beamformer Capable: [SU-BEAMFORMER] -# Indicates support for operation as a single user beamformer -# 0 = Not supported (default) -# 1 = Supported -# -# SU Beamformee Capable: [SU-BEAMFORMEE] -# Indicates support for operation as a single user beamformee -# 0 = Not supported (default) -# 1 = Supported -# -# Compressed Steering Number of Beamformer Antennas Supported: -# [BF-ANTENNA-2] [BF-ANTENNA-3] [BF-ANTENNA-4] -# Beamformee's capability indicating the maximum number of beamformer -# antennas the beamformee can support when sending compressed beamforming -# feedback -# If SU beamformer capable, set to maximum value minus 1 -# else reserved (default) -# -# Number of Sounding Dimensions: -# [SOUNDING-DIMENSION-2] [SOUNDING-DIMENSION-3] [SOUNDING-DIMENSION-4] -# Beamformer's capability indicating the maximum value of the NUM_STS parameter -# in the TXVECTOR of a VHT NDP -# If SU beamformer capable, set to maximum value minus 1 -# else reserved (default) -# -# MU Beamformer Capable: [MU-BEAMFORMER] -# Indicates support for operation as an MU beamformer -# 0 = Not supported or sent by Non-AP STA (default) -# 1 = Supported -# -# VHT TXOP PS: [VHT-TXOP-PS] -# Indicates whether or not the AP supports VHT TXOP Power Save Mode -# or whether or not the STA is in VHT TXOP Power Save mode -# 0 = VHT AP doesn't support VHT TXOP PS mode (OR) VHT STA not in VHT TXOP PS -# mode -# 1 = VHT AP supports VHT TXOP PS mode (OR) VHT STA is in VHT TXOP power save -# mode -# -# +HTC-VHT Capable: [HTC-VHT] -# Indicates whether or not the STA supports receiving a VHT variant HT Control -# field. -# 0 = Not supported (default) -# 1 = supported -# -# Maximum A-MPDU Length Exponent: [MAX-A-MPDU-LEN-EXP0]..[MAX-A-MPDU-LEN-EXP7] -# Indicates the maximum length of A-MPDU pre-EOF padding that the STA can recv -# This field is an integer in the range of 0 to 7. -# The length defined by this field is equal to -# 2 pow(13 + Maximum A-MPDU Length Exponent) -1 octets -# -# VHT Link Adaptation Capable: [VHT-LINK-ADAPT2] [VHT-LINK-ADAPT3] -# Indicates whether or not the STA supports link adaptation using VHT variant -# HT Control field -# If +HTC-VHTcapable is 1 -# 0 = (no feedback) if the STA does not provide VHT MFB (default) -# 1 = reserved -# 2 = (Unsolicited) if the STA provides only unsolicited VHT MFB -# 3 = (Both) if the STA can provide VHT MFB in response to VHT MRQ and if the -# STA provides unsolicited VHT MFB -# Reserved if +HTC-VHTcapable is 0 -# -# Rx Antenna Pattern Consistency: [RX-ANTENNA-PATTERN] -# Indicates the possibility of Rx antenna pattern change -# 0 = Rx antenna pattern might change during the lifetime of an association -# 1 = Rx antenna pattern does not change during the lifetime of an association -# -# Tx Antenna Pattern Consistency: [TX-ANTENNA-PATTERN] -# Indicates the possibility of Tx antenna pattern change -# 0 = Tx antenna pattern might change during the lifetime of an association -# 1 = Tx antenna pattern does not change during the lifetime of an association -#vht_capab=[SHORT-GI-80][HTC-VHT] -# -# Require stations to support VHT PHY (reject association if they do not) -#require_vht=1 - -# 0 = 20 or 40 MHz operating Channel width -# 1 = 80 MHz channel width -# 2 = 160 MHz channel width -# 3 = 80+80 MHz channel width -#vht_oper_chwidth=1 -# -# center freq = 5 GHz + (5 * index) -# So index 42 gives center freq 5.210 GHz -# which is channel 42 in 5G band -# -#vht_oper_centr_freq_seg0_idx=42 -# -# center freq = 5 GHz + (5 * index) -# So index 159 gives center freq 5.795 GHz -# which is channel 159 in 5G band -# -#vht_oper_centr_freq_seg1_idx=159 - -# Workaround to use station's nsts capability in (Re)Association Response frame -# This may be needed with some deployed devices as an interoperability -# workaround for beamforming if the AP's capability is greater than the -# station's capability. This is disabled by default and can be enabled by -# setting use_sta_nsts=1. -#use_sta_nsts=0 - -##### IEEE 802.11ax related configuration ##################################### - -#ieee80211ax: Whether IEEE 802.11ax (HE) is enabled -# 0 = disabled (default) -# 1 = enabled -#ieee80211ax=1 - -# disable_11ax: Boolean (0/1) to disable HE for a specific BSS -#disable_11ax=0 - -#he_su_beamformer: HE single user beamformer support -# 0 = not supported (default) -# 1 = supported -#he_su_beamformer=1 - -#he_su_beamformee: HE single user beamformee support -# 0 = not supported (default) -# 1 = supported -#he_su_beamformee=1 - -#he_mu_beamformer: HE multiple user beamformer support -# 0 = not supported (default) -# 1 = supported -#he_mu_beamformer=1 - -# he_bss_color: BSS color (1-63) -#he_bss_color=1 - -# he_bss_color_partial: BSS color AID equation -#he_bss_color_partial=0 - -#he_default_pe_duration: The duration of PE field in an HE PPDU in us -# Possible values are 0 us (default), 4 us, 8 us, 12 us, and 16 us -#he_default_pe_duration=0 - -#he_twt_required: Whether TWT is required -# 0 = not required (default) -# 1 = required -#he_twt_required=0 - -#he_twt_responder: Whether TWT (HE) responder is enabled -# 0 = disabled -# 1 = enabled if supported by the driver (default) -#he_twt_responder=1 - -#he_rts_threshold: Duration of STA transmission -# 0 = not set (default) -# unsigned integer = duration in units of 16 us -#he_rts_threshold=0 - -#he_er_su_disable: Disable 242-tone HE ER SU PPDU reception by the AP -# 0 = enable reception (default) -# 1 = disable reception -#he_er_su_disable=0 - -# HE operating channel information; see matching vht_* parameters for details. -# he_oper_centr_freq_seg0_idx field is used to indicate center frequency of 80 -# and 160 MHz bandwidth operation. In 80+80 MHz operation, it is the center -# frequency of the lower frequency segment. he_oper_centr_freq_seg1_idx field -# is used only with 80+80 MHz bandwidth operation and it is used to transmit -# the center frequency of the second segment. -# On the 6 GHz band the center freq calculation starts from 5.950 GHz offset. -# For example idx=3 would result in 5965 MHz center frequency. In addition, -# he_oper_chwidth is ignored, and the channel width is derived from the -# configured operating class or center frequency indexes (see -# IEEE P802.11ax/D6.1 Annex E, Table E-4). -#he_oper_chwidth -#he_oper_centr_freq_seg0_idx -#he_oper_centr_freq_seg1_idx - -#he_basic_mcs_nss_set: Basic NSS/MCS set -# 16-bit combination of 2-bit values of Max HE-MCS For 1..8 SS; each 2-bit -# value having following meaning: -# 0 = HE-MCS 0-7, 1 = HE-MCS 0-9, 2 = HE-MCS 0-11, 3 = not supported -#he_basic_mcs_nss_set - -#he_mu_edca_qos_info_param_count -#he_mu_edca_qos_info_q_ack -#he_mu_edca_qos_info_queue_request=1 -#he_mu_edca_qos_info_txop_request -#he_mu_edca_ac_be_aifsn=0 -#he_mu_edca_ac_be_ecwmin=15 -#he_mu_edca_ac_be_ecwmax=15 -#he_mu_edca_ac_be_timer=255 -#he_mu_edca_ac_bk_aifsn=0 -#he_mu_edca_ac_bk_aci=1 -#he_mu_edca_ac_bk_ecwmin=15 -#he_mu_edca_ac_bk_ecwmax=15 -#he_mu_edca_ac_bk_timer=255 -#he_mu_edca_ac_vi_ecwmin=15 -#he_mu_edca_ac_vi_ecwmax=15 -#he_mu_edca_ac_vi_aifsn=0 -#he_mu_edca_ac_vi_aci=2 -#he_mu_edca_ac_vi_timer=255 -#he_mu_edca_ac_vo_aifsn=0 -#he_mu_edca_ac_vo_aci=3 -#he_mu_edca_ac_vo_ecwmin=15 -#he_mu_edca_ac_vo_ecwmax=15 -#he_mu_edca_ac_vo_timer=255 - -# Spatial Reuse Parameter Set -# -# SR Control field value -# B0 = PSR Disallowed -# B1 = Non-SRG OBSS PD SR Disallowed -# B2 = Non-SRG Offset Present -# B3 = SRG Information Present -# B4 = HESIGA_Spatial_reuse_value15_allowed -#he_spr_sr_control -# -# Non-SRG OBSS PD Max Offset (included if he_spr_sr_control B2=1) -#he_spr_non_srg_obss_pd_max_offset - -# SRG OBSS PD Min Offset (included if he_spr_sr_control B3=1) -#he_spr_srg_obss_pd_min_offset -# -# SRG OBSS PD Max Offset (included if he_spr_sr_control B3=1) -#he_spr_srg_obss_pd_max_offset -# -# SPR SRG BSS Color (included if he_spr_sr_control B3=1) -# This config represents SRG BSS Color Bitmap field of Spatial Reuse Parameter -# Set element that indicates the BSS color values used by members of the -# SRG of which the transmitting STA is a member. The value is in range of 0-63. -#he_spr_srg_bss_colors=1 2 10 63 -# -# SPR SRG Partial BSSID (included if he_spr_sr_control B3=1) -# This config represents SRG Partial BSSID Bitmap field of Spatial Reuse -# Parameter Set element that indicates the Partial BSSID values used by members -# of the SRG of which the transmitting STA is a member. The value range -# corresponds to one of the 64 possible values of BSSID[39:44], where the lowest -# numbered bit corresponds to Partial BSSID value 0 and the highest numbered bit -# corresponds to Partial BSSID value 63. -#he_spr_srg_partial_bssid=0 1 3 63 -# -#he_6ghz_max_mpdu: Maximum MPDU Length of HE 6 GHz band capabilities. -# Indicates maximum MPDU length -# 0 = 3895 octets -# 1 = 7991 octets -# 2 = 11454 octets (default) -#he_6ghz_max_mpdu=2 -# -#he_6ghz_max_ampdu_len_exp: Maximum A-MPDU Length Exponent of HE 6 GHz band -# capabilities. Indicates the maximum length of A-MPDU pre-EOF padding that -# the STA can receive. This field is an integer in the range of 0 to 7. -# The length defined by this field is equal to -# 2 pow(13 + Maximum A-MPDU Length Exponent) -1 octets -# 0 = AMPDU length of 8k -# 1 = AMPDU length of 16k -# 2 = AMPDU length of 32k -# 3 = AMPDU length of 65k -# 4 = AMPDU length of 131k -# 5 = AMPDU length of 262k -# 6 = AMPDU length of 524k -# 7 = AMPDU length of 1048k (default) -#he_6ghz_max_ampdu_len_exp=7 -# -#he_6ghz_rx_ant_pat: Rx Antenna Pattern Consistency of HE 6 GHz capability. -# Indicates the possibility of Rx antenna pattern change -# 0 = Rx antenna pattern might change during the lifetime of an association -# 1 = Rx antenna pattern does not change during the lifetime of an association -# (default) -#he_6ghz_rx_ant_pat=1 -# -#he_6ghz_tx_ant_pat: Tx Antenna Pattern Consistency of HE 6 GHz capability. -# Indicates the possibility of Tx antenna pattern change -# 0 = Tx antenna pattern might change during the lifetime of an association -# 1 = Tx antenna pattern does not change during the lifetime of an association -# (default) -#he_6ghz_tx_ant_pat=1 - -# 6 GHz Access Point type -# This config is to set the 6 GHz Access Point type. Possible options are: -# 0 = Indoor AP (default) -# 1 = Standard Power AP -# This has no impact for operation on other bands. -#he_6ghz_reg_pwr_type=0 - -# Unsolicited broadcast Probe Response transmission settings -# This is for the 6 GHz band only. If the interval is set to a non-zero value, -# the AP schedules unsolicited broadcast Probe Response frames to be -# transmitted for in-band discovery. Refer to -# IEEE P802.11ax/D8.0 26.17.2.3.2, AP behavior for fast passive scanning. -# Valid range: 0..20 TUs; default is 0 (disabled) -#unsol_bcast_probe_resp_interval=0 - -##### IEEE 802.11be related configuration ##################################### - -#ieee80211be: Whether IEEE 802.11be (EHT) is enabled -# 0 = disabled (default) -# 1 = enabled -#ieee80211be=1 - -#disable_11be: Boolean (0/1) to disable EHT for a specific BSS -#disable_11be=0 - -#eht_su_beamformer: EHT single user beamformer support -# 0 = not supported (default) -# 1 = supported -#eht_su_beamformer=1 - -#eht_su_beamformee: EHT single user beamformee support -# 0 = not supported (default) -# 1 = supported -#eht_su_beamformee=1 - -#eht_mu_beamformer: EHT multiple user beamformer support -# 0 = not supported (default) -# 1 = supported -#eht_mu_beamformer=1 - -# EHT operating channel information; see matching he_* parameters for details. -# The field eht_oper_centr_freq_seg0_idx field is used to indicate center -# frequency of 40, 80, and 160 MHz bandwidth operation. -# In the 6 GHz band, eht_oper_chwidth is ignored and the channel width is -# derived from the configured operating class (IEEE P802.11be/D1.5, -# Annex E.1 - Country information and operating classes). -#eht_oper_chwidth -#eht_oper_centr_freq_seg0_idx - -##### IEEE 802.1X-2004 related configuration ################################## - -# Require IEEE 802.1X authorization -#ieee8021x=1 - -# IEEE 802.1X/EAPOL version -# hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL -# version 2. However, there are many client implementations that do not handle -# the new version number correctly (they seem to drop the frames completely). -# In order to make hostapd interoperate with these clients, the version number -# can be set to the older version (1) with this configuration value. -# Note: When using MACsec, eapol_version shall be set to 3, which is -# defined in IEEE Std 802.1X-2010. -#eapol_version=2 - -# Optional displayable message sent with EAP Request-Identity. The first \0 -# in this string will be converted to ASCII-0 (nul). This can be used to -# separate network info (comma separated list of attribute=value pairs); see, -# e.g., RFC 4284. -#eap_message=hello -#eap_message=hello\0networkid=netw,nasid=foo,portid=0,NAIRealms=example.com - -# WEP rekeying (disabled if key lengths are not set or are set to 0) -# Key lengths for default/broadcast and individual/unicast keys: -# 5 = 40-bit WEP (also known as 64-bit WEP with 40 secret bits) -# 13 = 104-bit WEP (also known as 128-bit WEP with 104 secret bits) -#wep_key_len_broadcast=5 -#wep_key_len_unicast=5 -# Rekeying period in seconds. 0 = do not rekey (i.e., set keys only once) -#wep_rekey_period=300 - -# EAPOL-Key index workaround (set bit7) for WinXP Supplicant (needed only if -# only broadcast keys are used) eapol_key_index_workaround=0 - -# EAP reauthentication period in seconds (default: 3600 seconds; 0 = disable -# reauthentication). -# Note: Reauthentications may enforce a disconnection, check the related -# parameter wpa_deny_ptk0_rekey for details. -#eap_reauth_period=3600 - -# Use PAE group address (01:80:c2:00:00:03) instead of individual target -# address when sending EAPOL frames with driver=wired. This is the most common -# mechanism used in wired authentication, but it also requires that the port -# is only used by one station. -#use_pae_group_addr=1 - -# EAP Re-authentication Protocol (ERP) authenticator (RFC 6696) -# -# Whether to initiate EAP authentication with EAP-Initiate/Re-auth-Start before -# EAP-Identity/Request -#erp_send_reauth_start=1 -# -# Domain name for EAP-Initiate/Re-auth-Start. Omitted from the message if not -# set (no local ER server). This is also used by the integrated EAP server if -# ERP is enabled (eap_server_erp=1). -#erp_domain=example.com - -##### MACsec ################################################################## - -# macsec_policy: IEEE 802.1X/MACsec options -# This determines how sessions are secured with MACsec (only for MACsec -# drivers). -# 0: MACsec not in use (default) -# 1: MACsec enabled - Should secure, accept key server's advice to -# determine whether to use a secure session or not. -# -# macsec_integ_only: IEEE 802.1X/MACsec transmit mode -# This setting applies only when MACsec is in use, i.e., -# - macsec_policy is enabled -# - the key server has decided to enable MACsec -# 0: Encrypt traffic (default) -# 1: Integrity only -# -# macsec_replay_protect: IEEE 802.1X/MACsec replay protection -# This setting applies only when MACsec is in use, i.e., -# - macsec_policy is enabled -# - the key server has decided to enable MACsec -# 0: Replay protection disabled (default) -# 1: Replay protection enabled -# -# macsec_replay_window: IEEE 802.1X/MACsec replay protection window -# This determines a window in which replay is tolerated, to allow receipt -# of frames that have been misordered by the network. -# This setting applies only when MACsec replay protection active, i.e., -# - macsec_replay_protect is enabled -# - the key server has decided to enable MACsec -# 0: No replay window, strict check (default) -# 1..2^32-1: number of packets that could be misordered -# -# macsec_port: IEEE 802.1X/MACsec port -# Port component of the SCI -# Range: 1-65534 (default: 1) -# -# mka_priority (Priority of MKA Actor) -# Range: 0..255 (default: 255) -# -# macsec_csindex: IEEE 802.1X/MACsec cipher suite -# 0 = GCM-AES-128 (default) -# 1 = GCM-AES-256 (default) -# -# mka_cak, mka_ckn, and mka_priority: IEEE 802.1X/MACsec pre-shared key mode -# This allows to configure MACsec with a pre-shared key using a (CAK,CKN) pair. -# In this mode, instances of hostapd can act as MACsec peers. The peer -# with lower priority will become the key server and start distributing SAKs. -# mka_cak (CAK = Secure Connectivity Association Key) takes a 16-byte (128-bit) -# hex-string (32 hex-digits) or a 32-byte (256-bit) hex-string (64 hex-digits) -# mka_ckn (CKN = CAK Name) takes a 1..32-bytes (8..256 bit) hex-string -# (2..64 hex-digits) - -##### Integrated EAP server ################################################### - -# Optionally, hostapd can be configured to use an integrated EAP server -# to process EAP authentication locally without need for an external RADIUS -# server. This functionality can be used both as a local authentication server -# for IEEE 802.1X/EAPOL and as a RADIUS server for other devices. - -# Use integrated EAP server instead of external RADIUS authentication -# server. This is also needed if hostapd is configured to act as a RADIUS -# authentication server. eap_server=0 - -# Path for EAP server user database -# If SQLite support is included, this can be set to "sqlite:/path/to/sqlite.db" -# to use SQLite database instead of a text file. -#eap_user_file=/etc/hostapd.eap_user - -# CA certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS -#ca_cert=/etc/hostapd.ca.pem - -# Server certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS -#server_cert=/etc/hostapd.server.pem - -# Private key matching with the server certificate for EAP-TLS/PEAP/TTLS -# This may point to the same file as server_cert if both certificate and key -# are included in a single file. PKCS#12 (PFX) file (.p12/.pfx) can also be -# used by commenting out server_cert and specifying the PFX file as the -# private_key. -#private_key=/etc/hostapd.server.prv - -# Passphrase for private key -#private_key_passwd=secret passphrase - -# An alternative server certificate and private key can be configured with the -# following parameters (with values just like the parameters above without the -# '2' suffix). The ca_cert file (in PEM encoding) is used to add the trust roots -# for both server certificates and/or client certificates). -# -# The main use case for this alternative server certificate configuration is to -# enable both RSA and ECC public keys. The server will pick which one to use -# based on the client preferences for the cipher suite (in the TLS ClientHello -# message). It should be noted that number of deployed EAP peer implementations -# do not filter out the cipher suite list based on their local configuration and -# as such, configuration of alternative types of certificates on the server may -# result in interoperability issues. -#server_cert2=/etc/hostapd.server-ecc.pem -#private_key2=/etc/hostapd.server-ecc.prv -#private_key_passwd2=secret passphrase - - -# Server identity -# EAP methods that provide mechanism for authenticated server identity delivery -# use this value. If not set, "hostapd" is used as a default. -#server_id=server.example.com - -# Enable CRL verification. -# Note: hostapd does not yet support CRL downloading based on CDP. Thus, a -# valid CRL signed by the CA is required to be included in the ca_cert file. -# This can be done by using PEM format for CA certificate and CRL and -# concatenating these into one file. Whenever CRL changes, hostapd needs to be -# restarted to take the new CRL into use. Alternatively, crl_reload_interval can -# be used to configure periodic updating of the loaded CRL information. -# 0 = do not verify CRLs (default) -# 1 = check the CRL of the user certificate -# 2 = check all CRLs in the certificate path -#check_crl=1 - -# Specify whether to ignore certificate CRL validity time mismatches with -# errors X509_V_ERR_CRL_HAS_EXPIRED and X509_V_ERR_CRL_NOT_YET_VALID. -# -# 0 = ignore errors -# 1 = do not ignore errors (default) -#check_crl_strict=1 - -# CRL reload interval in seconds -# This can be used to reload ca_cert file and the included CRL on every new TLS -# session if difference between last reload and the current reload time in -# seconds is greater than crl_reload_interval. -# Note: If interval time is very short, CPU overhead may be negatively affected -# and it is advised to not go below 300 seconds. -# This is applicable only with check_crl values 1 and 2. -# 0 = do not reload CRLs (default) -# crl_reload_interval = 300 - -# If check_cert_subject is set, the value of every field will be checked -# against the DN of the subject in the client certificate. If the values do -# not match, the certificate verification will fail, rejecting the user. -# This option allows hostapd to match every individual field in the right order -# against the DN of the subject in the client certificate. -# -# For example, check_cert_subject=C=US/O=XX/OU=ABC/OU=XYZ/CN=1234 will check -# every individual DN field of the subject in the client certificate. If OU=XYZ -# comes first in terms of the order in the client certificate (DN field of -# client certificate C=US/O=XX/OU=XYZ/OU=ABC/CN=1234), hostapd will reject the -# client because the order of 'OU' is not matching the specified string in -# check_cert_subject. -# -# This option also allows '*' as a wildcard. This option has some limitation. -# It can only be used as per the following example. -# -# For example, check_cert_subject=C=US/O=XX/OU=Production* and we have two -# clients and DN of the subject in the first client certificate is -# (C=US/O=XX/OU=Production Unit) and DN of the subject in the second client is -# (C=US/O=XX/OU=Production Factory). In this case, hostapd will allow both -# clients because the value of 'OU' field in both client certificates matches -# 'OU' value in 'check_cert_subject' up to 'wildcard'. -# -# * (Allow all clients, e.g., check_cert_subject=*) -#check_cert_subject=string - -# TLS Session Lifetime in seconds -# This can be used to allow TLS sessions to be cached and resumed with an -# abbreviated handshake when using EAP-TLS/TTLS/PEAP. -# (default: 0 = session caching and resumption disabled) -#tls_session_lifetime=3600 - -# TLS flags -# [ALLOW-SIGN-RSA-MD5] = allow MD5-based certificate signatures (depending on -# the TLS library, these may be disabled by default to enforce stronger -# security) -# [DISABLE-TIME-CHECKS] = ignore certificate validity time (this requests -# the TLS library to accept certificates even if they are not currently -# valid, i.e., have expired or have not yet become valid; this should be -# used only for testing purposes) -# [DISABLE-TLSv1.0] = disable use of TLSv1.0 -# [ENABLE-TLSv1.0] = explicitly enable use of TLSv1.0 (this allows -# systemwide TLS policies to be overridden) -# [DISABLE-TLSv1.1] = disable use of TLSv1.1 -# [ENABLE-TLSv1.1] = explicitly enable use of TLSv1.1 (this allows -# systemwide TLS policies to be overridden) -# [DISABLE-TLSv1.2] = disable use of TLSv1.2 -# [ENABLE-TLSv1.2] = explicitly enable use of TLSv1.2 (this allows -# systemwide TLS policies to be overridden) -# [DISABLE-TLSv1.3] = disable use of TLSv1.3 -# [ENABLE-TLSv1.3] = enable TLSv1.3 (experimental - disabled by default) -#tls_flags=[flag1][flag2]... - -# Maximum number of EAP message rounds with data (default: 100) -#max_auth_rounds=100 - -# Maximum number of short EAP message rounds (default: 50) -#max_auth_rounds_short=50 - -# Cached OCSP stapling response (DER encoded) -# If set, this file is sent as a certificate status response by the EAP server -# if the EAP peer requests certificate status in the ClientHello message. -# This cache file can be updated, e.g., by running following command -# periodically to get an update from the OCSP responder: -# openssl ocsp \ -# -no_nonce \ -# -CAfile /etc/hostapd.ca.pem \ -# -issuer /etc/hostapd.ca.pem \ -# -cert /etc/hostapd.server.pem \ -# -url http://ocsp.example.com:8888/ \ -# -respout /tmp/ocsp-cache.der -#ocsp_stapling_response=/tmp/ocsp-cache.der - -# Cached OCSP stapling response list (DER encoded OCSPResponseList) -# This is similar to ocsp_stapling_response, but the extended version defined in -# RFC 6961 to allow multiple OCSP responses to be provided. -#ocsp_stapling_response_multi=/tmp/ocsp-multi-cache.der - -# dh_file: File path to DH/DSA parameters file (in PEM format) -# This is an optional configuration file for setting parameters for an -# ephemeral DH key exchange. If the file is in DSA parameters format, it will -# be automatically converted into DH params. If the used TLS library supports -# automatic DH parameter selection, that functionality will be used if this -# parameter is not set. DH parameters are required if anonymous EAP-FAST is -# used. -# You can generate DH parameters file with OpenSSL, e.g., -# "openssl dhparam -out /etc/hostapd.dh.pem 2048" -#dh_file=/etc/hostapd.dh.pem - -# OpenSSL cipher string -# -# This is an OpenSSL specific configuration option for configuring the default -# ciphers. If not set, the value configured at build time ("DEFAULT:!EXP:!LOW" -# by default) is used. -# See https://www.openssl.org/docs/apps/ciphers.html for OpenSSL documentation -# on cipher suite configuration. This is applicable only if hostapd is built to -# use OpenSSL. -#openssl_ciphers=DEFAULT:!EXP:!LOW - -# OpenSSL ECDH curves -# -# This is an OpenSSL specific configuration option for configuring the ECDH -# curves for EAP-TLS/TTLS/PEAP/FAST server. If not set, automatic curve -# selection is enabled. If set to an empty string, ECDH curve configuration is -# not done (the exact library behavior depends on the library version). -# Otherwise, this is a colon separated list of the supported curves (e.g., -# P-521:P-384:P-256). This is applicable only if hostapd is built to use -# OpenSSL. This must not be used for Suite B cases since the same OpenSSL -# parameter is set differently in those cases and this might conflict with that -# design. -#openssl_ecdh_curves=P-521:P-384:P-256 - -# Fragment size for EAP methods -#fragment_size=1400 - -# Finite cyclic group for EAP-pwd. Number maps to group of domain parameters -# using the IANA repository for IKE (RFC 2409). -#pwd_group=19 - -# Configuration data for EAP-SIM database/authentication gateway interface. -# This is a text string in implementation specific format. The example -# implementation in eap_sim_db.c uses this as the UNIX domain socket name for -# the HLR/AuC gateway (e.g., hlr_auc_gw). In this case, the path uses "unix:" -# prefix. If hostapd is built with SQLite support (CONFIG_SQLITE=y in .config), -# database file can be described with an optional db= parameter. -#eap_sim_db=unix:/tmp/hlr_auc_gw.sock -#eap_sim_db=unix:/tmp/hlr_auc_gw.sock db=/tmp/hostapd.db - -# EAP-SIM DB request timeout -# This parameter sets the maximum time to wait for a database request response. -# The parameter value is in seconds. -#eap_sim_db_timeout=1 - -# Encryption key for EAP-FAST PAC-Opaque values. This key must be a secret, -# random value. It is configured as a 16-octet value in hex format. It can be -# generated, e.g., with the following command: -# od -tx1 -v -N16 /dev/random | colrm 1 8 | tr -d ' ' -#pac_opaque_encr_key=000102030405060708090a0b0c0d0e0f - -# EAP-FAST authority identity (A-ID) -# A-ID indicates the identity of the authority that issues PACs. The A-ID -# should be unique across all issuing servers. In theory, this is a variable -# length field, but due to some existing implementations requiring A-ID to be -# 16 octets in length, it is strongly recommended to use that length for the -# field to provide interoperability with deployed peer implementations. This -# field is configured in hex format. -#eap_fast_a_id=101112131415161718191a1b1c1d1e1f - -# EAP-FAST authority identifier information (A-ID-Info) -# This is a user-friendly name for the A-ID. For example, the enterprise name -# and server name in a human-readable format. This field is encoded as UTF-8. -#eap_fast_a_id_info=test server - -# Enable/disable different EAP-FAST provisioning modes: -#0 = provisioning disabled -#1 = only anonymous provisioning allowed -#2 = only authenticated provisioning allowed -#3 = both provisioning modes allowed (default) -#eap_fast_prov=3 - -# EAP-FAST PAC-Key lifetime in seconds (hard limit) -#pac_key_lifetime=604800 - -# EAP-FAST PAC-Key refresh time in seconds (soft limit on remaining hard -# limit). The server will generate a new PAC-Key when this number of seconds -# (or fewer) of the lifetime remains. -#pac_key_refresh_time=86400 - -# EAP-TEAP authentication type -# 0 = inner EAP (default) -# 1 = Basic-Password-Auth -# 2 = Do not require Phase 2 authentication if client can be authenticated -# during Phase 1 -#eap_teap_auth=0 - -# EAP-TEAP authentication behavior when using PAC -# 0 = perform inner authentication (default) -# 1 = skip inner authentication (inner EAP/Basic-Password-Auth) -#eap_teap_pac_no_inner=0 - -# EAP-TEAP behavior with Result TLV -# 0 = include with Intermediate-Result TLV (default) -# 1 = send in a separate message (for testing purposes) -#eap_teap_separate_result=0 - -# EAP-TEAP identities -# 0 = allow any identity type (default) -# 1 = require user identity -# 2 = require machine identity -# 3 = request user identity; accept either user or machine identity -# 4 = request machine identity; accept either user or machine identity -# 5 = require both user and machine identity -#eap_teap_id=0 - -# EAP-SIM and EAP-AKA protected success/failure indication using AT_RESULT_IND -# (default: 0 = disabled). -#eap_sim_aka_result_ind=1 - -# EAP-SIM and EAP-AKA identity options -# 0 = do not use pseudonyms or fast reauthentication -# 1 = use pseudonyms, but not fast reauthentication -# 2 = do not use pseudonyms, but use fast reauthentication -# 3 = use pseudonyms and use fast reauthentication (default) -#eap_sim_id=3 - -# IMSI privacy key (PEM encoded RSA 2048-bit private key) for decrypting -# permanent identity when using EAP-SIM/AKA/AKA'. -#imsi_privacy_key=imsi-privacy-key.pem - -# Trusted Network Connect (TNC) -# If enabled, TNC validation will be required before the peer is allowed to -# connect. Note: This is only used with EAP-TTLS and EAP-FAST. If any other -# EAP method is enabled, the peer will be allowed to connect without TNC. -#tnc=1 - -# EAP Re-authentication Protocol (ERP) - RFC 6696 -# -# Whether to enable ERP on the EAP server. -#eap_server_erp=1 - - -##### RADIUS client configuration ############################################# -# for IEEE 802.1X with external Authentication Server, IEEE 802.11 -# authentication with external ACL for MAC addresses, and accounting - -# The own IP address of the access point (used as NAS-IP-Address) own_ip_addr=127.0.0.1 - -# NAS-Identifier string for RADIUS messages. When used, this should be unique -# to the NAS within the scope of the RADIUS server. Please note that hostapd -# uses a separate RADIUS client for each BSS and as such, a unique -# nas_identifier value should be configured separately for each BSS. This is -# particularly important for cases where RADIUS accounting is used -# (Accounting-On/Off messages are interpreted as clearing all ongoing sessions -# and that may get interpreted as applying to all BSSes if the same -# NAS-Identifier value is used.) For example, a fully qualified domain name -# prefixed with a unique identifier of the BSS (e.g., BSSID) can be used here. -# -# When using IEEE 802.11r, nas_identifier must be set and must be between 1 and -# 48 octets long. -# -# It is mandatory to configure either own_ip_addr or nas_identifier to be -# compliant with the RADIUS protocol. When using RADIUS accounting, it is -# strongly recommended that nas_identifier is set to a unique value for each -# BSS. -#nas_identifier=ap.example.com - -# RADIUS client forced local IP address for the access point -# Normally the local IP address is determined automatically based on configured -# IP addresses, but this field can be used to force a specific address to be -# used, e.g., when the device has multiple IP addresses. -#radius_client_addr=127.0.0.1 - -# RADIUS client forced local interface. Helps run properly with VRF -# Default is none set which allows the network stack to pick the appropriate -# interface automatically. -# Example below binds to eth0 -#radius_client_dev=eth0 - -# RADIUS authentication server -#auth_server_addr=127.0.0.1 -#auth_server_port=1812 -#auth_server_shared_secret=secret - -# RADIUS accounting server -#acct_server_addr=127.0.0.1 -#acct_server_port=1813 -#acct_server_shared_secret=secret - -# Secondary RADIUS servers; to be used if primary one does not reply to -# RADIUS packets. These are optional and there can be more than one secondary -# server listed. -#auth_server_addr=127.0.0.2 -#auth_server_port=1812 -#auth_server_shared_secret=secret2 -# -#acct_server_addr=127.0.0.2 -#acct_server_port=1813 -#acct_server_shared_secret=secret2 - -# Retry interval for trying to return to the primary RADIUS server (in -# seconds). RADIUS client code will automatically try to use the next server -# when the current server is not replying to requests. If this interval is set, -# primary server will be retried after configured amount of time even if the -# currently used secondary server is still working. -#radius_retry_primary_interval=600 - - -# Interim accounting update interval -# If this is set (larger than 0) and acct_server is configured, hostapd will -# send interim accounting updates every N seconds. Note: if set, this overrides -# possible Acct-Interim-Interval attribute in Access-Accept message. Thus, this -# value should not be configured in hostapd.conf, if RADIUS server is used to -# control the interim interval. -# This value should not be less 600 (10 minutes) and must not be less than -# 60 (1 minute). -#radius_acct_interim_interval=600 - -# Request Chargeable-User-Identity (RFC 4372) -# This parameter can be used to configure hostapd to request CUI from the -# RADIUS server by including Chargeable-User-Identity attribute into -# Access-Request packets. -#radius_request_cui=1 - -# Dynamic VLAN mode; allow RADIUS authentication server to decide which VLAN -# is used for the stations. This information is parsed from following RADIUS -# attributes based on RFC 3580 and RFC 2868: Tunnel-Type (value 13 = VLAN), -# Tunnel-Medium-Type (value 6 = IEEE 802), Tunnel-Private-Group-ID (value -# VLANID as a string). Optionally, the local MAC ACL list (accept_mac_file) can -# be used to set static client MAC address to VLAN ID mapping. -# Dynamic VLAN mode is also used with VLAN ID assignment based on WPA/WPA2 -# passphrase from wpa_psk_file or vlan_id parameter from sae_password. -# 0 = disabled (default); only VLAN IDs from accept_mac_file will be used -# 1 = optional; use default interface if RADIUS server does not include VLAN ID -# 2 = required; reject authentication if RADIUS server does not include VLAN ID -#dynamic_vlan=0 - -# Per-Station AP_VLAN interface mode -# If enabled, each station is assigned its own AP_VLAN interface. -# This implies per-station group keying and ebtables filtering of inter-STA -# traffic (when passed through the AP). -# If the sta is not assigned to any VLAN, then its AP_VLAN interface will be -# added to the bridge given by the "bridge" configuration option (see above). -# Otherwise, it will be added to the per-VLAN bridge. -# 0 = disabled (default) -# 1 = enabled -#per_sta_vif=0 - -# VLAN interface list for dynamic VLAN mode is read from a separate text file. -# This list is used to map VLAN ID from the RADIUS server to a network -# interface. Each station is bound to one interface in the same way as with -# multiple BSSIDs or SSIDs. Each line in this text file is defining a new -# interface and the line must include VLAN ID and interface name separated by -# white space (space or tab). -# If no entries are provided by this file, the station is statically mapped -# to . interfaces. -# Each line can optionally also contain the name of a bridge to add the VLAN to -#vlan_file=/etc/hostapd.vlan - -# Interface where 802.1q tagged packets should appear when a RADIUS server is -# used to determine which VLAN a station is on. hostapd creates a bridge for -# each VLAN. Then hostapd adds a VLAN interface (associated with the interface -# indicated by 'vlan_tagged_interface') and the appropriate wireless interface -# to the bridge. -#vlan_tagged_interface=eth0 - -# Bridge (prefix) to add the wifi and the tagged interface to. This gets the -# VLAN ID appended. It defaults to brvlan%d if no tagged interface is given -# and br%s.%d if a tagged interface is given, provided %s = tagged interface -# and %d = VLAN ID. -#vlan_bridge=brvlan - -# When hostapd creates a VLAN interface on vlan_tagged_interfaces, it needs -# to know how to name it. -# 0 = vlan, e.g., vlan1 -# 1 = ., e.g. eth0.1 -#vlan_naming=0 - -# Arbitrary RADIUS attributes can be added into Access-Request and -# Accounting-Request packets by specifying the contents of the attributes with -# the following configuration parameters. There can be multiple of these to -# add multiple attributes. These parameters can also be used to override some -# of the attributes added automatically by hostapd. -# Format: [:] -# attr_id: RADIUS attribute type (e.g., 26 = Vendor-Specific) -# syntax: s = string (UTF-8), d = integer, x = octet string -# value: attribute value in format indicated by the syntax -# If syntax and value parts are omitted, a null value (single 0x00 octet) is -# used. -# -# Additional Access-Request attributes -# radius_auth_req_attr=[:] -# Examples: -# Operator-Name = "Operator" -#radius_auth_req_attr=126:s:Operator -# Service-Type = Framed (2) -#radius_auth_req_attr=6:d:2 -# Connect-Info = "testing" (this overrides the automatically generated value) -#radius_auth_req_attr=77:s:testing -# Same Connect-Info value set as a hexdump -#radius_auth_req_attr=77:x:74657374696e67 - -# -# Additional Accounting-Request attributes -# radius_acct_req_attr=[:] -# Examples: -# Operator-Name = "Operator" -#radius_acct_req_attr=126:s:Operator - -# If SQLite support is included, path to a database from which additional -# RADIUS request attributes are extracted based on the station MAC address. -# -# The schema for the radius_attributes table is: -# id | sta | reqtype | attr : multi-key (sta, reqtype) -# id = autonumber -# sta = station MAC address in `11:22:33:44:55:66` format. -# type = `auth` | `acct` | NULL (match any) -# attr = existing config file format, e.g. `126:s:Test Operator` -#radius_req_attr_sqlite=radius_attr.sqlite - -# Dynamic Authorization Extensions (RFC 5176) -# This mechanism can be used to allow dynamic changes to user session based on -# commands from a RADIUS server (or some other disconnect client that has the -# needed session information). For example, Disconnect message can be used to -# request an associated station to be disconnected. -# -# This is disabled by default. Set radius_das_port to non-zero UDP port -# number to enable. -#radius_das_port=3799 -# -# DAS client (the host that can send Disconnect/CoA requests) and shared secret -# Format: -# IP address 0.0.0.0 can be used to allow requests from any address. -#radius_das_client=192.168.1.123 shared secret here -# -# DAS Event-Timestamp time window in seconds -#radius_das_time_window=300 -# -# DAS require Event-Timestamp -#radius_das_require_event_timestamp=1 -# -# DAS require Message-Authenticator -#radius_das_require_message_authenticator=1 - -##### RADIUS authentication server configuration ############################## - -# hostapd can be used as a RADIUS authentication server for other hosts. This -# requires that the integrated EAP server is also enabled and both -# authentication services are sharing the same configuration. - -# File name of the RADIUS clients configuration for the RADIUS server. If this -# commented out, RADIUS server is disabled. -#radius_server_clients=/etc/hostapd.radius_clients - -# The UDP port number for the RADIUS authentication server -#radius_server_auth_port=1812 - -# The UDP port number for the RADIUS accounting server -# Commenting this out or setting this to 0 can be used to disable RADIUS -# accounting while still enabling RADIUS authentication. -#radius_server_acct_port=1813 - -# Use IPv6 with RADIUS server (IPv4 will also be supported using IPv6 API) -#radius_server_ipv6=1 - - -##### WPA/IEEE 802.11i configuration ########################################## - -# Enable WPA. Setting this variable configures the AP to require WPA (either -# WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either -# wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK. -# Instead of wpa_psk / wpa_passphrase, wpa_psk_radius might suffice. -# For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys), -# RADIUS authentication server must be configured, and WPA-EAP must be included -# in wpa_key_mgmt. -# This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0) -# and/or WPA2 (full IEEE 802.11i/RSN): -# bit0 = WPA -# bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled) -# Note that WPA3 is also configured with bit1 since it uses RSN just like WPA2. -# In other words, for WPA3, wpa=2 is used the configuration (and -# wpa_key_mgmt=SAE for WPA3-Personal instead of wpa_key_mgmt=WPA-PSK). wpa=2 - -# Extended Key ID support for Individually Addressed frames -# -# Extended Key ID allows to rekey PTK keys without the impacts the "normal" -# PTK rekeying with only a single Key ID 0 has. It can only be used when the -# driver supports it and RSN/WPA2 is used with a CCMP/GCMP pairwise cipher. -# -# 0 = force off, i.e., use only Key ID 0 (default) -# 1 = enable and use Extended Key ID support when possible -# 2 = identical to 1 but start with Key ID 1 when possible -#extended_key_id=0 - -# WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit -# secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase -# (8..63 characters) that will be converted to PSK. This conversion uses SSID -# so the PSK changes when ASCII passphrase is used and the SSID is changed. -# wpa_psk (dot11RSNAConfigPSKValue) -# wpa_passphrase (dot11RSNAConfigPSKPassPhrase) -#wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef wpa_passphrase=bubblegum - -# Optionally, WPA PSKs can be read from a separate text file (containing list -# of (PSK,MAC address) pairs. This allows more than one PSK to be configured. -# Use absolute path name to make sure that the files can be read on SIGHUP -# configuration reloads. -#wpa_psk_file=/etc/hostapd.wpa_psk - -# Optionally, WPA passphrase can be received from RADIUS authentication server -# This requires macaddr_acl to be set to 2 (RADIUS) for wpa_psk_radius values -# 1 and 2. -# 0 = disabled (default) -# 1 = optional; use default passphrase/psk if RADIUS server does not include -# Tunnel-Password -# 2 = required; reject authentication if RADIUS server does not include -# Tunnel-Password -# 3 = ask RADIUS server during 4-way handshake if there is no locally -# configured PSK/passphrase for the STA -#wpa_psk_radius=0 - -# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The -# entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be -# added to enable SHA256-based stronger algorithms. -# WPA-PSK = WPA-Personal / WPA2-Personal -# WPA-PSK-SHA256 = WPA2-Personal using SHA256 -# WPA-EAP = WPA-Enterprise / WPA2-Enterprise -# WPA-EAP-SHA256 = WPA2-Enterprise using SHA256 -# SAE = SAE (WPA3-Personal) -# WPA-EAP-SUITE-B-192 = WPA3-Enterprise with 192-bit security/CNSA suite -# FT-PSK = FT with passphrase/PSK -# FT-EAP = FT with EAP -# FT-EAP-SHA384 = FT with EAP using SHA384 -# FT-SAE = FT with SAE -# FILS-SHA256 = Fast Initial Link Setup with SHA256 -# FILS-SHA384 = Fast Initial Link Setup with SHA384 -# FT-FILS-SHA256 = FT and Fast Initial Link Setup with SHA256 -# FT-FILS-SHA384 = FT and Fast Initial Link Setup with SHA384 -# OWE = Opportunistic Wireless Encryption (a.k.a. Enhanced Open) -# DPP = Device Provisioning Protocol -# OSEN = Hotspot 2.0 online signup with encryption -# (dot11RSNAConfigAuthenticationSuitesTable) wpa_key_mgmt=SAE WPA-PSK -# Set of accepted cipher suites (encryption algorithms) for pairwise keys -# (unicast packets). This is a space separated list of algorithms: -# CCMP = AES in Counter mode with CBC-MAC (CCMP-128) -# TKIP = Temporal Key Integrity Protocol -# CCMP-256 = AES in Counter mode with CBC-MAC with 256-bit key -# GCMP = Galois/counter mode protocol (GCMP-128) -# GCMP-256 = Galois/counter mode protocol with 256-bit key -# Group cipher suite (encryption algorithm for broadcast and multicast frames) -# is automatically selected based on this configuration. If only CCMP is -# allowed as the pairwise cipher, group cipher will also be CCMP. Otherwise, -# TKIP will be used as the group cipher. The optional group_cipher parameter can -# be used to override this automatic selection. -# -# (dot11RSNAConfigPairwiseCiphersTable) -# Pairwise cipher for WPA (v1) (default: TKIP) -#wpa_pairwise=TKIP CCMP -# Pairwise cipher for RSN/WPA2 (default: use wpa_pairwise value) -#rsn_pairwise=CCMP - -# Optional override for automatic group cipher selection -# This can be used to select a specific group cipher regardless of which -# pairwise ciphers were enabled for WPA and RSN. It should be noted that -# overriding the group cipher with an unexpected value can result in -# interoperability issues and in general, this parameter is mainly used for -# testing purposes. -#group_cipher=CCMP - -# Time interval for rekeying GTK (broadcast/multicast encryption keys) in -# seconds. (dot11RSNAConfigGroupRekeyTime) -# This defaults to 86400 seconds (once per day) when using CCMP/GCMP as the -# group cipher and 600 seconds (once per 10 minutes) when using TKIP as the -# group cipher. -#wpa_group_rekey=86400 - -# Rekey GTK when any STA that possesses the current GTK is leaving the BSS. -# (dot11RSNAConfigGroupRekeyStrict) -#wpa_strict_rekey=1 - -# The number of times EAPOL-Key Message 1/2 in the RSN Group Key Handshake is -#retried per GTK Handshake attempt. (dot11RSNAConfigGroupUpdateCount) -# This value should only be increased when stations are constantly -# deauthenticated during GTK rekeying with the log message -# "group key handshake failed...". -# You should consider to also increase wpa_pairwise_update_count then. -# Range 1..4294967295; default: 4 -#wpa_group_update_count=4 - -# Time interval for rekeying GMK (master key used internally to generate GTKs -# (in seconds). -#wpa_gmk_rekey=86400 - -# Maximum lifetime for PTK in seconds. This can be used to enforce rekeying of -# PTK to mitigate some attacks against TKIP deficiencies. -# Warning: PTK rekeying is buggy with many drivers/devices and with such -# devices, the only secure method to rekey the PTK without Extended Key ID -# support requires a disconnection. Check the related parameter -# wpa_deny_ptk0_rekey for details. -#wpa_ptk_rekey=600 - -# Workaround for PTK rekey issues -# -# PTK0 rekeys (rekeying the PTK without "Extended Key ID for Individually -# Addressed Frames") can degrade the security and stability with some cards. -# To avoid such issues hostapd can replace those PTK rekeys (including EAP -# reauthentications) with disconnects. -# -# Available options: -# 0 = always rekey when configured/instructed (default) -# 1 = only rekey when the local driver is explicitly indicating it can perform -# this operation without issues -# 2 = never allow PTK0 rekeys -#wpa_deny_ptk0_rekey=0 - -# The number of times EAPOL-Key Message 1/4 and Message 3/4 in the RSN 4-Way -# Handshake are retried per 4-Way Handshake attempt. -# (dot11RSNAConfigPairwiseUpdateCount) -# Range 1..4294967295; default: 4 -#wpa_pairwise_update_count=4 - -# Workaround for key reinstallation attacks -# -# This parameter can be used to disable retransmission of EAPOL-Key frames that -# are used to install keys (EAPOL-Key message 3/4 and group message 1/2). This -# is similar to setting wpa_group_update_count=1 and -# wpa_pairwise_update_count=1, but with no impact to message 1/4 and with -# extended timeout on the response to avoid causing issues with stations that -# may use aggressive power saving have very long time in replying to the -# EAPOL-Key messages. -# -# This option can be used to work around key reinstallation attacks on the -# station (supplicant) side in cases those station devices cannot be updated -# for some reason. By removing the retransmissions the attacker cannot cause -# key reinstallation with a delayed frame transmission. This is related to the -# station side vulnerabilities CVE-2017-13077, CVE-2017-13078, CVE-2017-13079, -# CVE-2017-13080, and CVE-2017-13081. -# -# This workaround might cause interoperability issues and reduced robustness of -# key negotiation especially in environments with heavy traffic load due to the -# number of attempts to perform the key exchange is reduced significantly. As -# such, this workaround is disabled by default (unless overridden in build -# configuration). To enable this, set the parameter to 1. -#wpa_disable_eapol_key_retries=1 - -# Enable IEEE 802.11i/RSN/WPA2 pre-authentication. This is used to speed up -# roaming be pre-authenticating IEEE 802.1X/EAP part of the full RSN -# authentication and key handshake before actually associating with a new AP. -# (dot11RSNAPreauthenticationEnabled) -#rsn_preauth=1 -# -# Space separated list of interfaces from which pre-authentication frames are -# accepted (e.g., 'eth0' or 'eth0 wlan0wds0'. This list should include all -# interface that are used for connections to other APs. This could include -# wired interfaces and WDS links. The normal wireless data interface towards -# associated stations (e.g., wlan0) should not be added, since -# pre-authentication is only used with APs other than the currently associated -# one. -#rsn_preauth_interfaces=eth0 - -# ieee80211w: Whether management frame protection (MFP) is enabled -# 0 = disabled (default) -# 1 = optional -# 2 = required -#ieee80211w=0 -# The most common configuration options for this based on the PMF (protected -# management frames) certification program are: -# PMF enabled: ieee80211w=1 and wpa_key_mgmt=WPA-EAP WPA-EAP-SHA256 -# PMF required: ieee80211w=2 and wpa_key_mgmt=WPA-EAP-SHA256 -# (and similarly for WPA-PSK and WPA-PSK-SHA256 if WPA2-Personal is used) -# WPA3-Personal-only mode: ieee80211w=2 and wpa_key_mgmt=SAE - -# Group management cipher suite -# Default: AES-128-CMAC (BIP) -# Other options (depending on driver support): -# BIP-GMAC-128 -# BIP-GMAC-256 -# BIP-CMAC-256 -# Note: All the stations connecting to the BSS will also need to support the -# selected cipher. The default AES-128-CMAC is the only option that is commonly -# available in deployed devices. -#group_mgmt_cipher=AES-128-CMAC - -# Beacon Protection (management frame protection for Beacon frames) -# This depends on management frame protection being enabled (ieee80211w != 0) -# and beacon protection support indication from the driver. -# 0 = disabled (default) -# 1 = enabled -#beacon_prot=0 - -# Association SA Query maximum timeout (in TU = 1.024 ms; for MFP) -# (maximum time to wait for a SA Query response) -# dot11AssociationSAQueryMaximumTimeout, 1...4294967295 -#assoc_sa_query_max_timeout=1000 - -# Association SA Query retry timeout (in TU = 1.024 ms; for MFP) -# (time between two subsequent SA Query requests) -# dot11AssociationSAQueryRetryTimeout, 1...4294967295 -#assoc_sa_query_retry_timeout=201 - -# ocv: Operating Channel Validation -# This is a countermeasure against multi-channel on-path attacks. -# Enabling this depends on the driver's support for OCV when the driver SME is -# used. If hostapd SME is used, this will be enabled just based on this -# configuration. -# Enabling this automatically also enables ieee80211w, if not yet enabled. -# 0 = disabled (default) -# 1 = enabled -# 2 = enabled in workaround mode - Allow STA that claims OCV capability to -# connect even if the STA doesn't send OCI or negotiate PMF. This -# workaround is to improve interoperability with legacy STAs which are -# wrongly copying reserved bits of RSN capabilities from the AP's -# RSNE into (Re)Association Request frames. When this configuration is -# enabled, the AP considers STA is OCV capable only when the STA indicates -# MFP capability in (Re)Association Request frames and sends OCI in -# EAPOL-Key msg 2/4/FT Reassociation Request frame/FILS (Re)Association -# Request frame; otherwise, the AP disables OCV for the current connection -# with the STA. Enabling this workaround mode reduced OCV protection to -# some extend since it allows misbehavior to go through. As such, this -# should be enabled only if interoperability with misbehaving STAs is -# needed. -#ocv=1 - -# disable_pmksa_caching: Disable PMKSA caching -# This parameter can be used to disable caching of PMKSA created through EAP -# authentication. RSN preauthentication may still end up using PMKSA caching if -# it is enabled (rsn_preauth=1). -# 0 = PMKSA caching enabled (default) -# 1 = PMKSA caching disabled -#disable_pmksa_caching=0 - -# okc: Opportunistic Key Caching (aka Proactive Key Caching) -# Allow PMK cache to be shared opportunistically among configured interfaces -# and BSSes (i.e., all configurations within a single hostapd process). -# 0 = disabled (default) -# 1 = enabled -#okc=1 - -# SAE password -# This parameter can be used to set passwords for SAE. By default, the -# wpa_passphrase value is used if this separate parameter is not used, but -# wpa_passphrase follows the WPA-PSK constraints (8..63 characters) even though -# SAE passwords do not have such constraints. If the BSS enabled both SAE and -# WPA-PSK and both values are set, SAE uses the sae_password values and WPA-PSK -# uses the wpa_passphrase value. -# -# Each sae_password entry is added to a list of available passwords. This -# corresponds to the dot11RSNAConfigPasswordValueEntry. sae_password value -# starts with the password (dot11RSNAConfigPasswordCredential). That value can -# be followed by optional peer MAC address (dot11RSNAConfigPasswordPeerMac) and -# by optional password identifier (dot11RSNAConfigPasswordIdentifier). In -# addition, an optional VLAN ID specification can be used to bind the station -# to the specified VLAN whenever the specific SAE password entry is used. -# -# If the peer MAC address is not included or is set to the wildcard address -# (ff:ff:ff:ff:ff:ff), the entry is available for any station to use. If a -# specific peer MAC address is included, only a station with that MAC address -# is allowed to use the entry. -# -# If the password identifier (with non-zero length) is included, the entry is -# limited to be used only with that specified identifier. - -# The last matching (based on peer MAC address and identifier) entry is used to -# select which password to use. Setting sae_password to an empty string has a -# special meaning of removing all previously added entries. -# -# sae_password uses the following encoding: -#[|mac=][|vlanid=] -#[|pk=][|id=] -# Examples: -#sae_password=secret -#sae_password=really secret|mac=ff:ff:ff:ff:ff:ff -#sae_password=example secret|mac=02:03:04:05:06:07|id=pw identifier -#sae_password=example secret|vlanid=3|id=pw identifier - -# SAE threshold for anti-clogging mechanism (dot11RSNASAEAntiCloggingThreshold) -# This parameter defines how many open SAE instances can be in progress at the -# same time before the anti-clogging mechanism is taken into use. -#sae_anti_clogging_threshold=5 (deprecated) -#anti_clogging_threshold=5 - -# Maximum number of SAE synchronization errors (dot11RSNASAESync) -# The offending SAE peer will be disconnected if more than this many -# synchronization errors happen. -#sae_sync=5 - -# Enabled SAE finite cyclic groups -# SAE implementation are required to support group 19 (ECC group defined over a -# 256-bit prime order field). This configuration parameter can be used to -# specify a set of allowed groups. If not included, only the mandatory group 19 -# is enabled. -# The group values are listed in the IANA registry: -# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-9 -# Note that groups 1, 2, 5, 22, 23, and 24 should not be used in production -# purposes due limited security (see RFC 8247). Groups that are not as strong as -# group 19 (ECC, NIST P-256) are unlikely to be useful for production use cases -# since all implementations are required to support group 19. -#sae_groups=19 20 21 - -# Require MFP for all associations using SAE -# This parameter can be used to enforce negotiation of MFP for all associations -# that negotiate use of SAE. This is used in cases where SAE-capable devices are -# known to be MFP-capable and the BSS is configured with optional MFP -# (ieee80211w=1) for legacy support. The non-SAE stations can connect without -# MFP while SAE stations are required to negotiate MFP if sae_require_mfp=1. -#sae_require_mfp=0 - -# SAE Confirm behavior -# By default, AP will send out only SAE Commit message in response to a received -# SAE Commit message. This parameter can be set to 1 to override that behavior -# to send both SAE Commit and SAE Confirm messages without waiting for the STA -# to send its SAE Confirm message first. -#sae_confirm_immediate=0 - -# SAE mechanism for PWE derivation -# 0 = hunting-and-pecking loop only (default without password identifier) -# 1 = hash-to-element only (default with password identifier) -# 2 = both hunting-and-pecking loop and hash-to-element enabled -# Note: The default value is likely to change from 0 to 2 once the new -# hash-to-element mechanism has received more interoperability testing. -# When using SAE password identifier, the hash-to-element mechanism is used -# regardless of the sae_pwe parameter value. -#sae_pwe=0 - -# FILS Cache Identifier (16-bit value in hexdump format) -#fils_cache_id=0011 - -# FILS Realm Information -# One or more FILS realms need to be configured when FILS is enabled. This list -# of realms is used to define which realms (used in keyName-NAI by the client) -# can be used with FILS shared key authentication for ERP. -#fils_realm=example.com -#fils_realm=example.org - -# FILS DH Group for PFS -# 0 = PFS disabled with FILS shared key authentication (default) -# 1-65535 DH Group to use for FILS PFS -#fils_dh_group=0 - -# OWE DH groups -# OWE implementations are required to support group 19 (NIST P-256). All groups -# that are supported by the implementation (e.g., groups 19, 20, and 21 when -# using OpenSSL) are enabled by default. This configuration parameter can be -# used to specify a limited set of allowed groups. The group values are listed -# in the IANA registry: -# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-10 -#owe_groups=19 20 21 - -# OWE PTK derivation workaround -# Initial OWE implementation used SHA256 when deriving the PTK for all OWE -# groups. This was supposed to change to SHA384 for group 20 and SHA512 for -# group 21. This parameter can be used to enable workaround for interoperability -# with stations that use SHA256 with groups 20 and 21. By default (0) only the -# appropriate hash function is accepted. When workaround is enabled (1), the -# appropriate hash function is tried first and if that fails, SHA256-based PTK -# derivation is attempted. This workaround can result in reduced security for -# groups 20 and 21, but is required for interoperability with older -# implementations. There is no impact to group 19 behavior. The workaround is -# disabled by default and can be enabled by uncommenting the following line. -#owe_ptk_workaround=1 - -# OWE transition mode configuration -# Pointer to the matching open/OWE BSS -#owe_transition_bssid= -# SSID in same format as ssid2 described above. -#owe_transition_ssid= -# Alternatively, OWE transition mode BSSID/SSID can be configured with a -# reference to a BSS operated by this hostapd process. -#owe_transition_ifname= - -# DHCP server for FILS HLP -# If configured, hostapd will act as a DHCP relay for all FILS HLP requests -# that include a DHCPDISCOVER message and send them to the specific DHCP -# server for processing. hostapd will then wait for a response from that server -# before replying with (Re)Association Response frame that encapsulates this -# DHCP response. own_ip_addr is used as the local address for the communication -# with the DHCP server. -#dhcp_server=127.0.0.1 - -# DHCP server UDP port -# Default: 67 -#dhcp_server_port=67 - -# DHCP relay UDP port on the local device -# Default: 67; 0 means not to bind any specific port -#dhcp_relay_port=67 - -# DHCP rapid commit proxy -# If set to 1, this enables hostapd to act as a DHCP rapid commit proxy to -# allow the rapid commit options (two message DHCP exchange) to be used with a -# server that supports only the four message DHCP exchange. This is disabled by -# default (= 0) and can be enabled by setting this to 1. -#dhcp_rapid_commit_proxy=0 - -# Wait time for FILS HLP (dot11HLPWaitTime) in TUs -# default: 30 TUs (= 30.72 milliseconds) -#fils_hlp_wait_time=30 - -# FILS Discovery frame transmission minimum and maximum interval settings. -# If fils_discovery_max_interval is non-zero, the AP enables FILS Discovery -# frame transmission. These values use TUs as the unit and have allowed range -# of 0-10000. fils_discovery_min_interval defaults to 20. -#fils_discovery_min_interval=20 -#fils_discovery_max_interval=0 - -# Transition Disable indication -# The AP can notify authenticated stations to disable transition mode in their -# network profiles when the network has completed transition steps, i.e., once -# sufficiently large number of APs in the ESS have been updated to support the -# more secure alternative. When this indication is used, the stations are -# expected to automatically disable transition mode and less secure security -# options. This includes use of WEP, TKIP (including use of TKIP as the group -# cipher), and connections without PMF. -# Bitmap bits: -# bit 0 (0x01): WPA3-Personal (i.e., disable WPA2-Personal = WPA-PSK and only -# allow SAE to be used) -# bit 1 (0x02): SAE-PK (disable SAE without use of SAE-PK) -# bit 2 (0x04): WPA3-Enterprise (move to requiring PMF) -# bit 3 (0x08): Enhanced Open (disable use of open network; require OWE) -# (default: 0 = do not include Transition Disable KDE) -#transition_disable=0x01 - -# PASN ECDH groups -# PASN implementations are required to support group 19 (NIST P-256). If this -# parameter is not set, only group 19 is supported by default. This -# configuration parameter can be used to specify a limited set of allowed -# groups. The group values are listed in the IANA registry: -# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-10 -#pasn_groups=19 20 21 - -# PASN comeback after time in TUs -# In case the AP is temporarily unable to handle a PASN authentication exchange -# due to a too large number of parallel operations, this value indicates to the -# peer after how many TUs it can try the PASN exchange again. -# (default: 10 TUs) -#pasn_comeback_after=10 - -##### IEEE 802.11r configuration ############################################## - -# Mobility Domain identifier (dot11FTMobilityDomainID, MDID) -# MDID is used to indicate a group of APs (within an ESS, i.e., sharing the -# same SSID) between which a STA can use Fast BSS Transition. -# 2-octet identifier as a hex string. -#mobility_domain=a1b2 - -# PMK-R0 Key Holder identifier (dot11FTR0KeyHolderID) -# 1 to 48 octet identifier. -# This is configured with nas_identifier (see RADIUS client section above). - -# Default lifetime of the PMK-R0 in seconds; range 60..4294967295 -# (default: 14 days / 1209600 seconds; 0 = disable timeout) -# (dot11FTR0KeyLifetime) -#ft_r0_key_lifetime=1209600 - -# Maximum lifetime for PMK-R1; applied only if not zero -# PMK-R1 is removed at latest after this limit. -# Removing any PMK-R1 for expiry can be disabled by setting this to -1. -# (default: 0) -#r1_max_key_lifetime=0 - -# PMK-R1 Key Holder identifier (dot11FTR1KeyHolderID) -# 6-octet identifier as a hex string. -# Defaults to BSSID. -#r1_key_holder=000102030405 - -# Reassociation deadline in time units (TUs / 1.024 ms; range 1000..65535) -# (dot11FTReassociationDeadline) -#reassociation_deadline=1000 - -# List of R0KHs in the same Mobility Domain -# format: <256-bit key as hex string> -# This list is used to map R0KH-ID (NAS Identifier) to a destination MAC -# address when requesting PMK-R1 key from the R0KH that the STA used during the -# Initial Mobility Domain Association. -#r0kh=02:01:02:03:04:05 r0kh-1.example.com 000102030405060708090a0b0c0d0e0f000102030405060708090a0b0c0d0e0f -#r0kh=02:01:02:03:04:06 r0kh-2.example.com 00112233445566778899aabbccddeeff00112233445566778899aabbccddeeff -# And so on.. One line per R0KH. -# Wildcard entry: -# Upon receiving a response from R0KH, it will be added to this list, so -# subsequent requests won't be broadcast. If R0KH does not reply, it will be -# temporarily blocked (see rkh_neg_timeout). -#r0kh=ff:ff:ff:ff:ff:ff * 00112233445566778899aabbccddeeff - -# List of R1KHs in the same Mobility Domain -# format: <256-bit key as hex string> -# This list is used to map R1KH-ID to a destination MAC address when sending -# PMK-R1 key from the R0KH. This is also the list of authorized R1KHs in the MD -# that can request PMK-R1 keys. -#r1kh=02:01:02:03:04:05 02:11:22:33:44:55 000102030405060708090a0b0c0d0e0f000102030405060708090a0b0c0d0e0f -#r1kh=02:01:02:03:04:06 02:11:22:33:44:66 00112233445566778899aabbccddeeff00112233445566778899aabbccddeeff -# And so on.. One line per R1KH. -# Wildcard entry: -# Upon receiving a request from an R1KH not yet known, it will be added to this -# list and thus will receive push notifications. -#r1kh=00:00:00:00:00:00 00:00:00:00:00:00 00112233445566778899aabbccddeeff - -# Timeout (seconds) for newly discovered R0KH/R1KH (see wildcard entries above) -# Special values: 0 -> do not expire -# Warning: do not cache implies no sequence number validation with wildcards -#rkh_pos_timeout=86400 (default = 1 day) - -# Timeout (milliseconds) for requesting PMK-R1 from R0KH using PULL request -# and number of retries. -#rkh_pull_timeout=1000 (default = 1 second) -#rkh_pull_retries=4 (default) - -# Timeout (seconds) for non replying R0KH (see wildcard entries above) -# Special values: 0 -> do not cache -# default: 60 seconds -#rkh_neg_timeout=60 - -# Note: The R0KH/R1KH keys used to be 128-bit in length before the message -# format was changed. That shorter key length is still supported for backwards -# compatibility of the configuration files. If such a shorter key is used, a -# 256-bit key is derived from it. For new deployments, configuring the 256-bit -# key is recommended. - -# Whether PMK-R1 push is enabled at R0KH -# 0 = do not push PMK-R1 to all configured R1KHs (default) -# 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived -#pmk_r1_push=1 - -# Whether to enable FT-over-DS -# 0 = FT-over-DS disabled -# 1 = FT-over-DS enabled (default) -#ft_over_ds=1 - -# Whether to generate FT response locally for PSK networks -# This avoids use of PMK-R1 push/pull from other APs with FT-PSK networks as -# the required information (PSK and other session data) is already locally -# available. -# 0 = disabled (default) -# 1 = enabled -#ft_psk_generate_local=0 - -##### Neighbor table ########################################################## -# Maximum number of entries kept in AP table (either for neighbor table or for -# detecting Overlapping Legacy BSS Condition). The oldest entry will be -# removed when adding a new entry that would make the list grow over this -# limit. Note! WFA certification for IEEE 802.11g requires that OLBC is -# enabled, so this field should not be set to 0 when using IEEE 802.11g. -# default: 255 -#ap_table_max_size=255 - -# Number of seconds of no frames received after which entries may be deleted -# from the AP table. Since passive scanning is not usually performed frequently -# this should not be set to very small value. In addition, there is no -# guarantee that every scan cycle will receive beacon frames from the -# neighboring APs. -# default: 60 -#ap_table_expiration_time=3600 - -# Maximum number of stations to track on the operating channel -# This can be used to detect dualband capable stations before they have -# associated, e.g., to provide guidance on which colocated BSS to use. -# Default: 0 (disabled) -#track_sta_max_num=100 - -# Maximum age of a station tracking entry in seconds -# Default: 180 -#track_sta_max_age=180 - -# Do not reply to group-addressed Probe Request from a station that was seen on -# another radio. -# Default: Disabled -# -# This can be used with enabled track_sta_max_num configuration on another -# interface controlled by the same hostapd process to restrict Probe Request -# frame handling from replying to group-addressed Probe Request frames from a -# station that has been detected to be capable of operating on another band, -# e.g., to try to reduce likelihood of the station selecting a 2.4 GHz BSS when -# the AP operates both a 2.4 GHz and 5 GHz BSS concurrently. -# -# Note: Enabling this can cause connectivity issues and increase latency for -# discovering the AP. -#no_probe_resp_if_seen_on=wlan1 - -# Reject authentication from a station that was seen on another radio. -# Default: Disabled -# -# This can be used with enabled track_sta_max_num configuration on another -# interface controlled by the same hostapd process to reject authentication -# attempts from a station that has been detected to be capable of operating on -# another band, e.g., to try to reduce likelihood of the station selecting a -# 2.4 GHz BSS when the AP operates both a 2.4 GHz and 5 GHz BSS concurrently. -# -# Note: Enabling this can cause connectivity issues and increase latency for -# connecting with the AP. -#no_auth_if_seen_on=wlan1 - -##### Wi-Fi Protected Setup (WPS) ############################################# - -# WPS state -# 0 = WPS disabled (default) -# 1 = WPS enabled, not configured -# 2 = WPS enabled, configured -#wps_state=2 - -# Whether to manage this interface independently from other WPS interfaces -# By default, a single hostapd process applies WPS operations to all configured -# interfaces. This parameter can be used to disable that behavior for a subset -# of interfaces. If this is set to non-zero for an interface, WPS commands -# issued on that interface do not apply to other interfaces and WPS operations -# performed on other interfaces do not affect this interface. -#wps_independent=0 - -# AP can be configured into a locked state where new WPS Registrar are not -# accepted, but previously authorized Registrars (including the internal one) -# can continue to add new Enrollees. -#ap_setup_locked=1 - -# Universally Unique IDentifier (UUID; see RFC 4122) of the device -# This value is used as the UUID for the internal WPS Registrar. If the AP -# is also using UPnP, this value should be set to the device's UPnP UUID. -# If not configured, UUID will be generated based on the local MAC address. -#uuid=12345678-9abc-def0-1234-56789abcdef0 - -# Note: If wpa_psk_file is set, WPS is used to generate random, per-device PSKs -# that will be appended to the wpa_psk_file. If wpa_psk_file is not set, the -# default PSK (wpa_psk/wpa_passphrase) will be delivered to Enrollees. Use of -# per-device PSKs is recommended as the more secure option (i.e., make sure to -# set wpa_psk_file when using WPS with WPA-PSK). - -# When an Enrollee requests access to the network with PIN method, the Enrollee -# PIN will need to be entered for the Registrar. PIN request notifications are -# sent to hostapd ctrl_iface monitor. In addition, they can be written to a -# text file that could be used, e.g., to populate the AP administration UI with -# pending PIN requests. If the following variable is set, the PIN requests will -# be written to the configured file. -#wps_pin_requests=/var/run/hostapd_wps_pin_requests - -# Device Name -# User-friendly description of device; up to 32 octets encoded in UTF-8 -#device_name=Wireless AP - -# Manufacturer -# The manufacturer of the device (up to 64 ASCII characters) -#manufacturer=Company - -# Model Name -# Model of the device (up to 32 ASCII characters) -#model_name=WAP - -# Model Number -# Additional device description (up to 32 ASCII characters) -#model_number=123 - -# Serial Number -# Serial number of the device (up to 32 characters) -#serial_number=12345 - -# Primary Device Type -# Used format: -- -# categ = Category as an integer value -# OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for -# default WPS OUI -# subcateg = OUI-specific Sub Category as an integer value -# Examples: -# 1-0050F204-1 (Computer / PC) -# 1-0050F204-2 (Computer / Server) -# 5-0050F204-1 (Storage / NAS) -# 6-0050F204-1 (Network Infrastructure / AP) -#device_type=6-0050F204-1 - -# OS Version -# 4-octet operating system version number (hex string) -#os_version=01020300 - -# Config Methods -# List of the supported configuration methods -# Available methods: usba ethernet label display ext_nfc_token int_nfc_token -# nfc_interface push_button keypad virtual_display physical_display -# virtual_push_button physical_push_button -#config_methods=label virtual_display virtual_push_button keypad - -# WPS capability discovery workaround for PBC with Windows 7 -# Windows 7 uses incorrect way of figuring out AP's WPS capabilities by acting -# as a Registrar and using M1 from the AP. The config methods attribute in that -# message is supposed to indicate only the configuration method supported by -# the AP in Enrollee role, i.e., to add an external Registrar. For that case, -# PBC shall not be used and as such, the PushButton config method is removed -# from M1 by default. If pbc_in_m1=1 is included in the configuration file, -# the PushButton config method is left in M1 (if included in config_methods -# parameter) to allow Windows 7 to use PBC instead of PIN (e.g., from a label -# in the AP). -#pbc_in_m1=1 - -# Static access point PIN for initial configuration and adding Registrars -# If not set, hostapd will not allow external WPS Registrars to control the -# access point. The AP PIN can also be set at runtime with hostapd_cli -# wps_ap_pin command. Use of temporary (enabled by user action) and random -# AP PIN is much more secure than configuring a static AP PIN here. As such, -# use of the ap_pin parameter is not recommended if the AP device has means for -# displaying a random PIN. -#ap_pin=12345670 - -# Skip building of automatic WPS credential -# This can be used to allow the automatically generated Credential attribute to -# be replaced with pre-configured Credential(s). -#skip_cred_build=1 - -# Additional Credential attribute(s) -# This option can be used to add pre-configured Credential attributes into M8 -# message when acting as a Registrar. If skip_cred_build=1, this data will also -# be able to override the Credential attribute that would have otherwise been -# automatically generated based on network configuration. This configuration -# option points to an external file that much contain the WPS Credential -# attribute(s) as binary data. -#extra_cred=hostapd.cred - -# Credential processing -# 0 = process received credentials internally (default) -# 1 = do not process received credentials; just pass them over ctrl_iface to -# external program(s) -# 2 = process received credentials internally and pass them over ctrl_iface -# to external program(s) -# Note: With wps_cred_processing=1, skip_cred_build should be set to 1 and -# extra_cred be used to provide the Credential data for Enrollees. -# -# wps_cred_processing=1 will disabled automatic updates of hostapd.conf file -# both for Credential processing and for marking AP Setup Locked based on -# validation failures of AP PIN. An external program is responsible on updating -# the configuration appropriately in this case. -#wps_cred_processing=0 - -# Whether to enable SAE (WPA3-Personal transition mode) automatically for -# WPA2-PSK credentials received using WPS. -# 0 = only add the explicitly listed WPA2-PSK configuration (default) -# 1 = add both the WPA2-PSK and SAE configuration and enable PMF so that the -# AP gets configured in WPA3-Personal transition mode (supports both -# WPA2-Personal (PSK) and WPA3-Personal (SAE) clients). -#wps_cred_add_sae=0 - -# AP Settings Attributes for M7 -# By default, hostapd generates the AP Settings Attributes for M7 based on the -# current configuration. It is possible to override this by providing a file -# with pre-configured attributes. This is similar to extra_cred file format, -# but the AP Settings attributes are not encapsulated in a Credential -# attribute. -#ap_settings=hostapd.ap_settings - -# Multi-AP backhaul BSS config -# Used in WPS when multi_ap=2 or 3. Defines "backhaul BSS" credentials. -# These are passed in WPS M8 instead of the normal (fronthaul) credentials -# if the Enrollee has the Multi-AP subelement set. Backhaul SSID is formatted -# like ssid2. The key is set like wpa_psk or wpa_passphrase. -#multi_ap_backhaul_ssid="backhaul" -#multi_ap_backhaul_wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef -#multi_ap_backhaul_wpa_passphrase=secret passphrase - -# WPS UPnP interface -# If set, support for external Registrars is enabled. -#upnp_iface=br0 - -# Friendly Name (required for UPnP) -# Short description for end use. Should be less than 64 characters. -#friendly_name=WPS Access Point - -# Manufacturer URL (optional for UPnP) -#manufacturer_url=http://www.example.com/ - -# Model Description (recommended for UPnP) -# Long description for end user. Should be less than 128 characters. -#model_description=Wireless Access Point - -# Model URL (optional for UPnP) -#model_url=http://www.example.com/model/ - -# Universal Product Code (optional for UPnP) -# 12-digit, all-numeric code that identifies the consumer package. -#upc=123456789012 - -# WPS RF Bands (a = 5G, b = 2.4G, g = 2.4G, ag = dual band, ad = 60 GHz) -# This value should be set according to RF band(s) supported by the AP if -# hw_mode is not set. For dual band dual concurrent devices, this needs to be -# set to ag to allow both RF bands to be advertized. -#wps_rf_bands=ag - -# NFC password token for WPS -# These parameters can be used to configure a fixed NFC password token for the -# AP. This can be generated, e.g., with nfc_pw_token from wpa_supplicant. When -# these parameters are used, the AP is assumed to be deployed with a NFC tag -# that includes the matching NFC password token (e.g., written based on the -# NDEF record from nfc_pw_token). -# -#wps_nfc_dev_pw_id: Device Password ID (16..65535) -#wps_nfc_dh_pubkey: Hexdump of DH Public Key -#wps_nfc_dh_privkey: Hexdump of DH Private Key -#wps_nfc_dev_pw: Hexdump of Device Password - -# Application Extension attribute for Beacon and Probe Response frames -# This parameter can be used to add application extension into WPS IE. The -# contents of this parameter starts with 16-octet (32 hexdump characters) of -# UUID to identify the specific application and that is followed by the actual -# application specific data. -#wps_application_ext= - -##### Wi-Fi Direct (P2P) ###################################################### - -# Enable P2P Device management -#manage_p2p=1 - -# Allow cross connection -#allow_cross_connection=1 - -##### Device Provisioning Protocol (DPP) ###################################### - -# Name for Enrollee's DPP Configuration Request -#dpp_name=Test - -# MUD URL for Enrollee's DPP Configuration Request (optional) -#dpp_mud_url=https://example.com/mud - -#dpp_connector -#dpp_netaccesskey -#dpp_netaccesskey_expiry -#dpp_csign -#dpp_controller - -# Configurator Connectivity indication -# 0: no Configurator is currently connected (default) -# 1: advertise that a Configurator is available -#dpp_configurator_connectivity=0 - -# DPP PFS -# 0: allow PFS to be used or not used (default) -# 1: require PFS to be used (note: not compatible with DPP R1) -# 2: do not allow PFS to be used -#dpp_pfs=0 - -#### TDLS (IEEE 802.11z-2010) ################################################# - -# Prohibit use of TDLS in this BSS -#tdls_prohibit=1 - -# Prohibit use of TDLS Channel Switching in this BSS -#tdls_prohibit_chan_switch=1 - -##### IEEE 802.11v-2011 ####################################################### - -# Time advertisement -# 0 = disabled (default) -# 2 = UTC time at which the TSF timer is 0 -#time_advertisement=2 - -# Local time zone as specified in 8.3 of IEEE Std 1003.1-2004: -# stdoffset[dst[offset][,start[/time],end[/time]]] -#time_zone=EST5 - -# WNM-Sleep Mode (extended sleep mode for stations) -# 0 = disabled (default) -# 1 = enabled (allow stations to use WNM-Sleep Mode) -#wnm_sleep_mode=1 - -# WNM-Sleep Mode GTK/IGTK workaround -# Normally, WNM-Sleep Mode exit with management frame protection negotiated -# would result in the current GTK/IGTK getting added into the WNM-Sleep Mode -# Response frame. Some station implementations may have a vulnerability that -# results in GTK/IGTK reinstallation based on this frame being replayed. This -# configuration parameter can be used to disable that behavior and use EAPOL-Key -# frames for GTK/IGTK update instead. This would likely be only used with -# wpa_disable_eapol_key_retries=1 that enables a workaround for similar issues -# with EAPOL-Key. This is related to station side vulnerabilities CVE-2017-13087 -# and CVE-2017-13088. To enable this AP-side workaround, set the parameter to 1. -#wnm_sleep_mode_no_keys=0 - -# BSS Transition Management -# 0 = disabled (default) -# 1 = enabled -#bss_transition=1 - -# Proxy ARP -# 0 = disabled (default) -# 1 = enabled -#proxy_arp=1 - -# IPv6 Neighbor Advertisement multicast-to-unicast conversion -# This can be used with Proxy ARP to allow multicast NAs to be forwarded to -# associated STAs using link layer unicast delivery. -# 0 = disabled (default) -# 1 = enabled -#na_mcast_to_ucast=0 - -##### IEEE 802.11u-2011 ####################################################### - -# Enable Interworking service -#interworking=1 - -# Access Network Type -# 0 = Private network -# 1 = Private network with guest access -# 2 = Chargeable public network -# 3 = Free public network -# 4 = Personal device network -# 5 = Emergency services only network -# 14 = Test or experimental -# 15 = Wildcard -#access_network_type=0 - -# Whether the network provides connectivity to the Internet -# 0 = Unspecified -# 1 = Network provides connectivity to the Internet -#internet=1 - -# Additional Step Required for Access -# Note: This is only used with open network, i.e., ASRA shall ne set to 0 if -# RSN is used. -#asra=0 - -# Emergency services reachable -#esr=0 - -# Unauthenticated emergency service accessible -#uesa=0 - -# Venue Info (optional) -# The available values are defined in IEEE Std 802.11u-2011, 7.3.1.34. -# Example values (group,type): -# 0,0 = Unspecified -# 1,7 = Convention Center -# 1,13 = Coffee Shop -# 2,0 = Unspecified Business -# 7,1 Private Residence -#venue_group=7 -#venue_type=1 - -# Homogeneous ESS identifier (optional; dot11HESSID) -# If set, this shall be identifical to one of the BSSIDs in the homogeneous -# ESS and this shall be set to the same value across all BSSs in homogeneous -# ESS. -#hessid=02:03:04:05:06:07 - -# Roaming Consortium List -# Arbitrary number of Roaming Consortium OIs can be configured with each line -# adding a new OI to the list. The first three entries are available through -# Beacon and Probe Response frames. Any additional entry will be available only -# through ANQP queries. Each OI is between 3 and 15 octets and is configured as -# a hexstring. -#roaming_consortium=021122 -#roaming_consortium=2233445566 - -# Venue Name information -# This parameter can be used to configure one or more Venue Name Duples for -# Venue Name ANQP information. Each entry has a two or three character language -# code (ISO-639) separated by colon from the venue name string. -# Note that venue_group and venue_type have to be set for Venue Name -# information to be complete. -#venue_name=eng:Example venue -#venue_name=fin:Esimerkkipaikka -# Alternative format for language:value strings: -# (double quoted string, printf-escaped string) -#venue_name=P"eng:Example\nvenue" - -# Venue URL information -# This parameter can be used to configure one or more Venue URL Duples to -# provide additional information corresponding to Venue Name information. -# Each entry has a Venue Number value separated by colon from the Venue URL -# string. Venue Number indicates the corresponding venue_name entry (1 = 1st -# venue_name, 2 = 2nd venue_name, and so on; 0 = no matching venue_name) -#venue_url=1:http://www.example.com/info-eng -#venue_url=2:http://www.example.com/info-fin - -# Network Authentication Type -# This parameter indicates what type of network authentication is used in the -# network. -# format: [redirect URL] -# Network Authentication Type Indicator values: -# 00 = Acceptance of terms and conditions -# 01 = On-line enrollment supported -# 02 = http/https redirection -# 03 = DNS redirection -#network_auth_type=00 -#network_auth_type=02http://www.example.com/redirect/me/here/ - -# IP Address Type Availability -# format: <1-octet encoded value as hex str> -# (ipv4_type & 0x3f) << 2 | (ipv6_type & 0x3) -# ipv4_type: -# 0 = Address type not available -# 1 = Public IPv4 address available -# 2 = Port-restricted IPv4 address available -# 3 = Single NATed private IPv4 address available -# 4 = Double NATed private IPv4 address available -# 5 = Port-restricted IPv4 address and single NATed IPv4 address available -# 6 = Port-restricted IPv4 address and double NATed IPv4 address available -# 7 = Availability of the address type is not known -# ipv6_type: -# 0 = Address type not available -# 1 = Address type available -# 2 = Availability of the address type not known -#ipaddr_type_availability=14 - -# Domain Name -# format: [,] -#domain_name=example.com,another.example.com,yet-another.example.com - -# 3GPP Cellular Network information -# format: [;][;...] -#anqp_3gpp_cell_net=244,91;310,026;234,56 - -# NAI Realm information -# One or more realm can be advertised. Each nai_realm line adds a new realm to -# the set. These parameters provide information for stations using Interworking -# network selection to allow automatic connection to a network based on -# credentials. -# format: ,[,][,][,...] -# encoding: -# 0 = Realm formatted in accordance with IETF RFC 4282 -# 1 = UTF-8 formatted character string that is not formatted in -# accordance with IETF RFC 4282 -# NAI Realm(s): Semi-colon delimited NAI Realm(s) -# EAP Method: [:<[AuthParam1:Val1]>][<[AuthParam2:Val2]>][...] -# EAP Method types, see: -# http://www.iana.org/assignments/eap-numbers/eap-numbers.xhtml#eap-numbers-4 -# AuthParam (Table 8-188 in IEEE Std 802.11-2012): -# ID 2 = Non-EAP Inner Authentication Type -# 1 = PAP, 2 = CHAP, 3 = MSCHAP, 4 = MSCHAPV2 -# ID 3 = Inner authentication EAP Method Type -# ID 5 = Credential Type -# 1 = SIM, 2 = USIM, 3 = NFC Secure Element, 4 = Hardware Token, -# 5 = Softoken, 6 = Certificate, 7 = username/password, 9 = Anonymous, -# 10 = Vendor Specific -#nai_realm=0,example.com;example.net -# EAP methods EAP-TLS with certificate and EAP-TTLS/MSCHAPv2 with -# username/password -#nai_realm=0,example.org,13[5:6],21[2:4][5:7] - -# Arbitrary ANQP-element configuration -# Additional ANQP-elements with arbitrary values can be defined by specifying -# their contents in raw format as a hexdump of the payload. Note that these -# values will override ANQP-element contents that may have been specified in the -# more higher layer configuration parameters listed above. -# format: anqp_elem=: -# For example, AP Geospatial Location ANQP-element with unknown location: -#anqp_elem=265:0000 -# For example, AP Civic Location ANQP-element with unknown location: -#anqp_elem=266:000000 - -# GAS Address 3 behavior -# 0 = P2P specification (Address3 = AP BSSID) workaround enabled by default -# based on GAS request Address3 -# 1 = IEEE 802.11 standard compliant regardless of GAS request Address3 -# 2 = Force non-compliant behavior (Address3 = AP BSSID for all cases) -#gas_address3=0 - -# QoS Map Set configuration -# -# Comma delimited QoS Map Set in decimal values -# (see IEEE Std 802.11-2012, 8.4.2.97) -# -# format: -# [,],... -# -# There can be up to 21 optional DSCP Exceptions which are pairs of DSCP Value -# (0..63 or 255) and User Priority (0..7). This is followed by eight DSCP Range -# descriptions with DSCP Low Value and DSCP High Value pairs (0..63 or 255) for -# each UP starting from 0. If both low and high value are set to 255, the -# corresponding UP is not used. -# -# default: not set -#qos_map_set=53,2,22,6,8,15,0,7,255,255,16,31,32,39,255,255,40,47,255,255 - -##### Hotspot 2.0 ############################################################# - -# Enable Hotspot 2.0 support -#hs20=1 - -# Disable Downstream Group-Addressed Forwarding (DGAF) -# This can be used to configure a network where no group-addressed frames are -# allowed. The AP will not forward any group-address frames to the stations and -# random GTKs are issued for each station to prevent associated stations from -# forging such frames to other stations in the BSS. -#disable_dgaf=1 - -# OSU Server-Only Authenticated L2 Encryption Network -#osen=1 - -# ANQP Domain ID (0..65535) -# An identifier for a set of APs in an ESS that share the same common ANQP -# information. 0 = Some of the ANQP information is unique to this AP (default). -#anqp_domain_id=1234 - -# Deauthentication request timeout -# If the RADIUS server indicates that the station is not allowed to connect to -# the BSS/ESS, the AP can allow the station some time to download a -# notification page (URL included in the message). This parameter sets that -# timeout in seconds. -#hs20_deauth_req_timeout=60 - -# Operator Friendly Name -# This parameter can be used to configure one or more Operator Friendly Name -# Duples. Each entry has a two or three character language code (ISO-639) -# separated by colon from the operator friendly name string. -#hs20_oper_friendly_name=eng:Example operator -#hs20_oper_friendly_name=fin:Esimerkkioperaattori - -# Connection Capability -# This can be used to advertise what type of IP traffic can be sent through the -# hotspot (e.g., due to firewall allowing/blocking protocols/ports). -# format: :: -# IP Protocol: 1 = ICMP, 6 = TCP, 17 = UDP -# Port Number: 0..65535 -# Status: 0 = Closed, 1 = Open, 2 = Unknown -# Each hs20_conn_capab line is added to the list of advertised tuples. -#hs20_conn_capab=1:0:2 -#hs20_conn_capab=6:22:1 -#hs20_conn_capab=17:5060:0 - -# WAN Metrics -# format: :
      :
        :
        :
          : -# WAN Info: B0-B1: Link Status, B2: Symmetric Link, B3: At Capabity -# (encoded as two hex digits) -# Link Status: 1 = Link up, 2 = Link down, 3 = Link in test state -# Downlink Speed: Estimate of WAN backhaul link current downlink speed in kbps; -# 1..4294967295; 0 = unknown -# Uplink Speed: Estimate of WAN backhaul link current uplink speed in kbps -# 1..4294967295; 0 = unknown -# Downlink Load: Current load of downlink WAN connection (scaled to 255 = 100%) -# Uplink Load: Current load of uplink WAN connection (scaled to 255 = 100%) -# Load Measurement Duration: Duration for measuring downlink/uplink load in -# tenths of a second (1..65535); 0 if load cannot be determined -#hs20_wan_metrics=01:8000:1000:80:240:3000 - -# Operating Class Indication -# List of operating classes the BSSes in this ESS use. The Global operating -# classes in Table E-4 of IEEE Std 802.11-2012 Annex E define the values that -# can be used in this. -# format: hexdump of operating class octets -# for example, operating classes 81 (2.4 GHz channels 1-13) and 115 (5 GHz -# channels 36-48): -#hs20_operating_class=5173 - -# Terms and Conditions information -# -# hs20_t_c_filename contains the Terms and Conditions filename that the AP -# indicates in RADIUS Access-Request messages. -#hs20_t_c_filename=terms-and-conditions -# -# hs20_t_c_timestamp contains the Terms and Conditions timestamp that the AP -# indicates in RADIUS Access-Request messages. Usually, this contains the number -# of seconds since January 1, 1970 00:00 UTC showing the time when the file was -# last modified. -#hs20_t_c_timestamp=1234567 -# -# hs20_t_c_server_url contains a template for the Terms and Conditions server -# URL. This template is used to generate the URL for a STA that needs to -# acknowledge Terms and Conditions. Unlike the other hs20_t_c_* parameters, this -# parameter is used on the authentication server, not the AP. -# Macros: -# @1@ = MAC address of the STA (colon separated hex octets) -#hs20_t_c_server_url=https://example.com/t_and_c?addr=@1@&ap=123 - -# OSU and Operator icons -# ::::: -#hs20_icon=32:32:eng:image/png:icon32:/tmp/icon32.png -#hs20_icon=64:64:eng:image/png:icon64:/tmp/icon64.png - -# OSU SSID (see ssid2 for format description) -# This is the SSID used for all OSU connections to all the listed OSU Providers. -#osu_ssid="example" - -# OSU Providers -# One or more sets of following parameter. Each OSU provider is started by the -# mandatory osu_server_uri item. The other parameters add information for the -# last added OSU provider. osu_nai specifies the OSU_NAI value for OSEN -# authentication when using a standalone OSU BSS. osu_nai2 specifies the OSU_NAI -# value for OSEN authentication when using a shared BSS (Single SSID) for OSU. -# -#osu_server_uri=https://example.com/osu/ -#osu_friendly_name=eng:Example operator -#osu_friendly_name=fin:Esimerkkipalveluntarjoaja -#osu_nai=anonymous@example.com -#osu_nai2=anonymous@example.com -#osu_method_list=1 0 -#osu_icon=icon32 -#osu_icon=icon64 -#osu_service_desc=eng:Example services -#osu_service_desc=fin:Esimerkkipalveluja -# -#osu_server_uri=... - -# Operator Icons -# Operator icons are specified using references to the hs20_icon entries -# (Name subfield). This information, if present, is advertsised in the -# Operator Icon Metadata ANQO-element. -#operator_icon=icon32 -#operator_icon=icon64 - -##### Multiband Operation (MBO) ############################################### -# -# MBO enabled -# 0 = disabled (default) -# 1 = enabled -#mbo=1 -# -# Cellular data connection preference -# 0 = Excluded - AP does not want STA to use the cellular data connection -# 1 = AP prefers the STA not to use cellular data connection -# 255 = AP prefers the STA to use cellular data connection -#mbo_cell_data_conn_pref=1 - -##### Optimized Connectivity Experience (OCE) ################################# -# -# Enable OCE specific features (bitmap) -# BIT(0) - Reserved -# Set BIT(1) (= 2) to enable OCE in STA-CFON mode -# Set BIT(2) (= 4) to enable OCE in AP mode -# Default is 0 = OCE disabled -#oce=0 - -# RSSI-based association rejection -# -# Reject STA association if RSSI is below given threshold (in dBm) -# Allowed range: -60 to -90 dBm; default = 0 (rejection disabled) -# Note: This rejection happens based on a signal strength detected while -# receiving a single frame and as such, there is significant risk of the value -# not being accurate and this resulting in valid stations being rejected. As -# such, this functionality is not recommended to be used for purposes other than -# testing. -#rssi_reject_assoc_rssi=-75 -# -# Association retry delay in seconds allowed by the STA if RSSI has not met the -# threshold (range: 0..255, default=30). -#rssi_reject_assoc_timeout=30 - -# Ignore Probe Request frames if RSSI is below given threshold (in dBm) -# Allowed range: -60 to -90 dBm; default = 0 (rejection disabled) -#rssi_ignore_probe_request=-75 - -##### Fast Session Transfer (FST) support ##################################### -# -# The options in this section are only available when the build configuration -# option CONFIG_FST is set while compiling hostapd. They allow this interface -# to be a part of FST setup. -# -# FST is the transfer of a session from a channel to another channel, in the -# same or different frequency bands. -# -# For detals, see IEEE Std 802.11ad-2012. - -# Identifier of an FST Group the interface belongs to. -#fst_group_id=bond0 - -# Interface priority within the FST Group. -# Announcing a higher priority for an interface means declaring it more -# preferable for FST switch. -# fst_priority is in 1..255 range with 1 being the lowest priority. -#fst_priority=100 - -# Default LLT value for this interface in milliseconds. The value used in case -# no value provided during session setup. Default is 50 ms. -# fst_llt is in 1..4294967 range (due to spec limitation, see 10.32.2.2 -# Transitioning between states). -#fst_llt=100 - -##### Radio measurements / location ########################################### - -# The content of a LCI measurement subelement -#lci= - -# The content of a location civic measurement subelement -#civic= - -# Enable neighbor report via radio measurements -#rrm_neighbor_report=1 - -# Enable beacon report via radio measurements -#rrm_beacon_report=1 - -# Publish fine timing measurement (FTM) responder functionality -# This parameter only controls publishing via Extended Capabilities element. -# Actual functionality is managed outside hostapd. -#ftm_responder=0 - -# Publish fine timing measurement (FTM) initiator functionality -# This parameter only controls publishing via Extended Capabilities element. -# Actual functionality is managed outside hostapd. -#ftm_initiator=0 -# -# Stationary AP config indicates that the AP doesn't move hence location data -# can be considered as always up to date. If configured, LCI data will be sent -# as a radio measurement even if the request doesn't contain a max age element -# that allows sending of such data. Default: 0. -#stationary_ap=0 - -# Enable reduced neighbor reporting (RNR) -#rnr=0 - -##### Airtime policy configuration ########################################### - -# Set the airtime policy operating mode: -# 0 = disabled (default) -# 1 = static config -# 2 = per-BSS dynamic config -# 3 = per-BSS limit mode -#airtime_mode=0 - -# Interval (in milliseconds) to poll the kernel for updated station activity in -# dynamic and limit modes -#airtime_update_interval=200 - -# Static configuration of station weights (when airtime_mode=1). Kernel default -# weight is 256; set higher for larger airtime share, lower for smaller share. -# Each entry is a MAC address followed by a weight. -#airtime_sta_weight=02:01:02:03:04:05 256 -#airtime_sta_weight=02:01:02:03:04:06 512 - -# Per-BSS airtime weight. In multi-BSS mode, set for each BSS and hostapd will -# configure station weights to enforce the correct ratio between BSS weights -# depending on the number of active stations. The *ratios* between different -# BSSes is what's important, not the absolute numbers. -# Must be set for all BSSes if airtime_mode=2 or 3, has no effect otherwise. -#airtime_bss_weight=1 - -# Whether the current BSS should be limited (when airtime_mode=3). -# -# If set, the BSS weight ratio will be applied in the case where the current BSS -# would exceed the share defined by the BSS weight ratio. E.g., if two BSSes are -# set to the same weights, and one is set to limited, the limited BSS will get -# no more than half the available airtime, but if the non-limited BSS has more -# stations active, that *will* be allowed to exceed its half of the available -# airtime. -#airtime_bss_limit=1 - -##### EDMG support ############################################################ -# -# Enable EDMG capability for AP mode in the 60 GHz band. Default value is false. -# To configure channel bonding for an EDMG AP use edmg_channel below. -# If enable_edmg is set and edmg_channel is not set, EDMG CB1 will be -# configured. -#enable_edmg=1 -# -# Configure channel bonding for AP mode in the 60 GHz band. -# This parameter is relevant only if enable_edmg is set. -# Default value is 0 (no channel bonding). -#edmg_channel=9 - -##### TESTING OPTIONS ######################################################### -# -# The options in this section are only available when the build configuration -# option CONFIG_TESTING_OPTIONS is set while compiling hostapd. They allow -# testing some scenarios that are otherwise difficult to reproduce. -# -# Ignore probe requests sent to hostapd with the given probability, must be a -# floating point number in the range [0, 1). -#ignore_probe_probability=0.0 -# -# Ignore authentication frames with the given probability -#ignore_auth_probability=0.0 -# -# Ignore association requests with the given probability -#ignore_assoc_probability=0.0 -# -# Ignore reassociation requests with the given probability -#ignore_reassoc_probability=0.0 -# -# Corrupt Key MIC in GTK rekey EAPOL-Key frames with the given probability -#corrupt_gtk_rekey_mic_probability=0.0 -# -# Include only ECSA IE without CSA IE where possible -# (channel switch operating class is needed) -#ecsa_ie_only=0 - -##### Multiple BSSID support ################################################## -# -# Above configuration is using the default interface (wlan#, or multi-SSID VLAN -# interfaces). Other BSSIDs can be added by using separator 'bss' with -# default interface name to be allocated for the data packets of the new BSS. -# -# hostapd will generate BSSID mask based on the BSSIDs that are -# configured. hostapd will verify that dev_addr & MASK == dev_addr. If this is -# not the case, the MAC address of the radio must be changed before starting -# hostapd (ifconfig wlan0 hw ether ). If a BSSID is configured for -# every secondary BSS, this limitation is not applied at hostapd and other -# masks may be used if the driver supports them (e.g., swap the locally -# administered bit) -# -# BSSIDs are assigned in order to each BSS, unless an explicit BSSID is -# specified using the 'bssid' parameter. -# If an explicit BSSID is specified, it must be chosen such that it: -# - results in a valid MASK that covers it and the dev_addr -# - is not the same as the MAC address of the radio -# - is not the same as any other explicitly specified BSSID -# -# Alternatively, the 'use_driver_iface_addr' parameter can be used to request -# hostapd to use the driver auto-generated interface address (e.g., to use the -# exact MAC addresses allocated to the device). -# -# Not all drivers support multiple BSSes. The exact mechanism for determining -# the driver capabilities is driver specific. With the current (i.e., a recent -# kernel) drivers using nl80211, this information can be checked with "iw list" -# (search for "valid interface combinations"). -# -# Please note that hostapd uses some of the values configured for the first BSS -# as the defaults for the following BSSes. However, it is recommended that all -# BSSes include explicit configuration of all relevant configuration items. -# -#bss=wlan0_0 -#ssid=test2 -# most of the above items can be used here (apart from radio interface specific -# items, like channel) - -#bss=wlan0_1 -#bssid=00:13:10:95:fe:0b -# ... +rsn_pairwise=CCMP diff --git a/Attacker/installTools.sh b/Attacker/installTools.sh index 9475397..2165c90 100644 --- a/Attacker/installTools.sh +++ b/Attacker/installTools.sh @@ -144,8 +144,8 @@ apt-get install arp-scan -y #airgeddon -sudo apt-get install tshark john lighttpd pixiewps isc-dhcp-server reaver crunch xterm hostapd-y -sudo apt-get install asleap bettercap ettercap-text-only hcxtools hcxdumptool bully mdk4 beef-xss -y +sudo apt-get install tshark john lighttpd pixiewps isc-dhcp-server reaver crunch xterm hostapd -y +sudo apt-get install ettercap-text-only hcxdumptool mdk4 -y sudo systemctl disable lighttpd sudo systemctl stop lighttpd cd $TOOLS @@ -169,7 +169,7 @@ sudo ln -s /root/tools/hostapd-mana/hostapd/hostapd /usr/bin/hostapd-mana #eapeak cd $TOOLS -sudo apt-get install python-dev libssl-dev swig python3-dev gcc python-m2crypto -y +sudo apt-get install python-dev libssl-dev swig python3-dev gcc -y sudo pip3 install pipenv #pip2 install m2crypto @@ -200,7 +200,7 @@ cd $TOOLS git clone https://github.com/sensepost/berate_ap #MD4 -apt-get install pkg-config libnl-3-dev libnl-genl-3-dev libpcap-dev +apt-get install pkg-config libnl-3-dev libnl-genl-3-dev libpcap-dev -y cd $TOOLS git clone https://github.com/aircrack-ng/mdk4 cd mdk4