rules.mk

#----------------------------------------------------------------------------
# On command line:
#
# make = Make software.
#
# make clean = Clean out built project files.
#
# That's pretty much all you need. To compile, always go make clean,
# followed by make.
#
# For advanced users only:
# make teensy = Download the hex file to the device, using teensy_loader_cli.
#               (must have teensy_loader_cli installed).
#
#----------------------------------------------------------------------------

# # project specific files
SRC += matrix.c

# MCU name
MCU = atmega32u4

# Processor frequency.
#     This will define a symbol, F_CPU, in all source code files equal to the
#     processor frequency in Hz. You can then use this symbol in your source code to
#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
#     automatically to create a 32-bit value in your source code.
#
#     This will be an integer division of F_USB below, as it is sourced by
#     F_USB after it has run through any CPU prescalers. Note that this value
#     does not *change* the processor frequency - it should merely be updated to
#     reflect the processor speed set externally so that the code can use accurate
#     software delays.
F_CPU = 16000000


#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8

# Input clock frequency.
#     This will define a symbol, F_USB, in all source code files equal to the
#     input clock frequency (before any prescaling is performed) in Hz. This value may
#     differ from F_CPU if prescaling is used on the latter, and is required as the
#     raw input clock is fed directly to the PLL sections of the AVR for high speed
#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
#     at the end, this will be done automatically to create a 32-bit value in your
#     source code.
#
#     If no clock division is performed on the input clock inside the AVR (via the
#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)

# Bootloader
#     This definition is optional, and if your keyboard supports multiple bootloaders of
#     different sizes, comment this out, and the correct address will be loaded
#     automatically (+60). See bootloader.mk for all options.
BOOTLOADER = halfkay

# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT

# If you have Left LEDs (see
# https://geekhack.org/index.php?topic=22780.msg873819#msg873819 for
# details), include the following define:
# OPT_DEFS += -DLEFT_LEDS

# Build Options
#   comment out to disable the options.
#
BOOTMAGIC_ENABLE = no  # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE  = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE  = yes # Audio control and System control(+450)
CONSOLE_ENABLE   = no  # Console for debug(+400)
COMMAND_ENABLE   = yes # Commands for debug and configuration
CUSTOM_MATRIX    = yes # Custom matrix file for the ErgoDox EZ
NKRO_ENABLE      = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
UNICODE_ENABLE   = yes # Unicode
SWAP_HANDS_ENABLE= yes # Allow swapping hands of keyboard
SLEEP_LED_ENABLE = no
API_SYSEX_ENABLE = no
RGBLIGHT_ENABLE = yes
RGB_MATRIX_ENABLE = no # enable later
DEBOUNCE_TYPE = eager_pr

ifeq ($(strip $(RGB_MATRIX_ENABLE)), no)
  SRC += i2c_master.c
endif


LAYOUTS = ergodox