Skip to content

Latest commit

 

History

History
168 lines (120 loc) · 6.38 KB

turn-howto.md

File metadata and controls

168 lines (120 loc) · 6.38 KB

Overview

This document explains how to enable VoIP relaying on your homeserver with TURN.

The synapse Matrix homeserver supports integration with TURN server via the TURN server REST API. This allows the homeserver to generate credentials that are valid for use on the TURN server through the use of a secret shared between the homeserver and the TURN server.

This documentation provides two TURN server configuration examples:

Requirements

For TURN relaying to work, the TURN service must be hosted on a server/endpoint with a public IP.

Hosting TURN behind NAT requires port forwarding and for the NAT gateway to have a public IP. However, even with appropriate configuration, NAT is known to cause issues and to often not work.

Afterwards, the homeserver needs some further configuration.

Synapse setup

Your homeserver configuration file needs the following extra keys:

  1. turn_uris
  2. turn_shared_secret
  3. turn_user_lifetime
  4. turn_allow_guests

As an example, here is the relevant section of the config file for matrix.org. The turn_uris are appropriate for TURN servers listening on the default ports, with no TLS.

turn_uris: [ "turn:turn.matrix.org?transport=udp", "turn:turn.matrix.org?transport=tcp" ]
turn_shared_secret: "n0t4ctuAllymatr1Xd0TorgSshar3d5ecret4obvIousreAsons"
turn_user_lifetime: 86400000
turn_allow_guests: true

After updating the homeserver configuration, you must restart synapse:

  • If you use synctl:
    # Depending on how Synapse is installed, synctl may already be on
    # your PATH. If not, you may need to activate a virtual environment.
    synctl restart
  • If you use systemd:
    systemctl restart matrix-synapse.service

... and then reload any clients (or wait an hour for them to refresh their settings).

Troubleshooting

The normal symptoms of a misconfigured TURN server are that calls between devices on different networks ring, but get stuck at "call connecting". Unfortunately, troubleshooting this can be tricky.

Here are a few things to try:

  • Check that you have opened your firewall to allow TCP and UDP traffic to the TURN ports (normally 3478 and 5349).

  • Check that you have opened your firewall to allow UDP traffic to the UDP relay ports (49152-65535 by default).

  • Try disabling TLS/DTLS listeners and enable only its (unencrypted) TCP/UDP listeners. (This will only leave signaling traffic unencrypted; voice & video WebRTC traffic is always encrypted.)

  • Some WebRTC implementations (notably, that of Google Chrome) appear to get confused by TURN servers which are reachable over IPv6 (this appears to be an unexpected side-effect of its handling of multiple IP addresses as defined by draft-ietf-rtcweb-ip-handling).

    Try removing any AAAA records for your TURN server, so that it is only reachable over IPv4.

  • If your TURN server is behind NAT:

    • double-check that your NAT gateway is correctly forwarding all TURN ports (normally 3478 & 5349 for TCP & UDP TURN traffic, and 49152-65535 for the UDP relay) to the NAT-internal address of your TURN server. If advertising both IPv4 and IPv6 external addresses via the external-ip option, ensure that the NAT is forwarding both IPv4 and IPv6 traffic to the IPv4 and IPv6 internal addresses of your TURN server. When in doubt, remove AAAA records for your TURN server and specify only an IPv4 address as your external-ip.

    • ensure that your TURN server uses the NAT gateway as its default route.

  • Enable more verbose logging, in coturn via the verbose setting:

    verbose
    

    or with eturnal with the shell command eturnalctl loglevel debug or in the configuration file (the service needs to reload for it to become effective):

        ## Logging configuration:
            log_level: debug

    ... and then see if there are any clues in its logs.

  • If you are using a browser-based client under Chrome, check chrome://webrtc-internals/ for insights into the internals of the negotiation. On Firefox, check the "Connection Log" on about:webrtc.

    (Understanding the output is beyond the scope of this document!)

  • You can test your Matrix homeserver TURN setup with https://test.voip.librepush.net/. Note that this test is not fully reliable yet, so don't be discouraged if the test fails. Here is the github repo of the source of the tester, where you can file bug reports.

  • There is a WebRTC test tool at https://webrtc.github.io/samples/src/content/peerconnection/trickle-ice/. To use it, you will need a username/password for your TURN server. You can either:

    • look for the GET /_matrix/client/r0/voip/turnServer request made by a matrix client to your homeserver in your browser's network inspector. In the response you should see username and password. Or:

    • Use the following shell commands for coturn:

      secret=staticAuthSecretHere
      
      u=$((`date +%s` + 3600)):test
      p=$(echo -n $u | openssl dgst -hmac $secret -sha1 -binary | base64)
      echo -e "username: $u\npassword: $p"

      or for eturnal

      eturnalctl credentials
    • Or (coturn only): Temporarily configure coturn to accept a static username/password. To do this, comment out use-auth-secret and static-auth-secret and add the following:

      lt-cred-mech
      user=username:password
      

      Note: these settings will not take effect unless use-auth-secret and static-auth-secret are disabled.

      Restart coturn after changing the configuration file.

      Remember to restore the original settings to go back to testing with Matrix clients!

    If the TURN server is working correctly, you should see at least one relay entry in the results.