Skip to content

Latest commit

 

History

History
84 lines (47 loc) · 3.4 KB

README.md

File metadata and controls

84 lines (47 loc) · 3.4 KB
Raw

27C322/160/800/400 EPROM Programming Adapter Series

GitHub issues

Introduction

This adapter converts the pin-outs of the parts listed below (which is similar to contemporary DIP-packaged mask ROMs) to 27C4096 pin-out as supported by the readily-available and cheap TL866 series of USB programmers.

The supported EPROMs parts are:

  • 27C400: 40-pin, 4Mbit (256k x 16-bit, 512k x 8-bit)
  • 27C800: 42-pin, 8Mbit (512k x 16-bit, 1M x 8-bit)
  • 27C160: 42-pin, 16Mbit (1M x 16-bit, 2M x 8-bit)
  • 27C322: 42-pin, 32Mbit (2M x 16-bit, no 8-bit access mode)

Design

This adapter was designed using KiCad 5.0, you can find the project files on the folder called kicad-project.

Top Side:

top

Bottom Side:

bottom

Usage

Insert the programming adapter into the TL866 with the socket handles adjacent to each other. Insert the EPROM into the lowest-possible position in the adapter and with pin 1 nearest the handle.

Adapter when in use

If your are programming a 27C322 EPROMs, move the switch to the Position 27c322, for 27C160 , 27C400 and 27C800 EPROMs, switch must be in the Position other.

Adapter mode

Software

The following instructions describe how to write a 27c160 EPROM.

Split the source EPROM into 512Kbytes parts, in this case I use the HJSplit, however other programs can be used.

HJSplit

Located the output path, for this example four files of 512Kbyte size with the extension ending on ".001" - ".004".

Launch the MiniPro software, select AMD 27C4096 DIP40 device, deselect Check ID and set Pulse Delay to 50us. You may also optionally reduce VPP Voltage to 12.50V, depending on your EPROM's datasheet and programming success.

MiniPro Software Configuration

The EPROM can now be accessed as if it were a 27C4096 device, 512kB at a time, as configured by the DIP Switch:

  • 27C400: program all 512kB in one pass.
  • 27C800: program in 2 (two) 512kB passes.
  • 27C160: program in 4 (four) 512kB passes.
  • 27C322: program in 8 (eight) 512kB passes.

Refere to the following table for DIP Switch configuration:

DIP Switch configuration

Troubleshooting

If you suffer write or verify errors when programming, try these steps:

  1. Make sure the EPROM is fully blank before programming it (Device -> Blank Check). All EPROMs available today are second-hand 'pulls' and sellers aren't always careful when erasing before resale.

  2. Open and close the adapter's ZIF lever a few times, and reposition the EPROM squarely in the socket.

  3. Try adjusting VPP Voltage between 12.50V and 13.50V. Subjectively I have had greater success at the higher voltage and it gives headroom for voltage losses in transferring VPP through the adapter's logic.

  4. Programming errors will occur from time to time, and of course the chances increase the larger the device. It makes sense to invest in a UV eraser. These are available at low cost on Ebay for around $15-20. Most devices will be erased after 10 to 20 minutes under UV light.

Hardware change log

R_20231123

  • Fix EDG-03 DIP Switch's correct polarity.
  • Update revision number to R_20231123
  • Update Version number to 1.1

V_20180919

  • Initial release.