Filament level

[clumsyzombie]

Question when you are in Bambu Lab Studio and are at the Device Screen and you are using Bambu Filament you can see the amount with a small line of what is left. If there any senser or any way tio pull this into Home assist to display the left of Filament left on a spool with out a cam on the AMS? I am not sure what I am even asking about but I was just thinking if that is something that can be pulled from some where.

Or is there away to have a Filament inventory systems that monitors what Filament you have even in the closet and when you start to get low you get an alert to reorder blah blah Filament

[t3chguy]

Yes, that info is already present in this integration.

[clumsyzombie]

So can you make a senser to grab like X1C-ClumsysLab-1-AMS Tray 3 and only grab Remain filament %
So I guess can you have a senser grab set attributes under a senser
So you can truly track the % left?

[clumsyzombie]

I got it figuered out sorry thanks a ton

sensor:

• platform: template
  sensors:
  spool_remaining_filament_tray_1:
  friendly_name: "Spool Remaining Filament Tray 1"
  unit_of_measurement: '%'
  value_template: "{{ state_attr('sensor.X1C-ClumsysLab-1-AMS_Tray_1', 'Remaining filament') }}"
  spool_remaining_filament_tray_2:
  friendly_name: "Spool Remaining Filament Tray 2"
  unit_of_measurement: '%'
  value_template: "{{ state_attr('sensor.X1C-ClumsysLab-1-AMS_Tray_2', 'Remaining filament') }}"
  spool_remaining_filament_tray_3:
  friendly_name: "Spool Remaining Filament Tray 3"
  unit_of_measurement: '%'
  value_template: "{{ state_attr('sensor.X1C-ClumsysLab-1-AMS_Tray_3', 'Remaining filament') }}"
  spool_remaining_filament_tray_4:
  friendly_name: "Spool Remaining Filament Tray 4"
  unit_of_measurement: '%'
  value_template:

[clumsyzombie]

Well I thought that code would work and it will not pull it so i am back tot he drawing board.

sensor:

• platform: template
  sensors:
  spool_remaining_filament_tray_1:
  friendly_name: "Spool Remaining Filament Tray 1"
  unit_of_measurement: '%'
  value_template: "{{ state_attr('sensor.X1C-ClumsysLab-1-AMS_Tray_1', 'Remaining filament') | float }}"
  spool_remaining_filament_tray_2:
  friendly_name: "Spool Remaining Filament Tray 2"
  unit_of_measurement: '%'
  value_template: "{{ state_attr('sensor.X1C-ClumsysLab-1-AMS_Tray_2', 'Remaining filament') | float }}"
  spool_remaining_filament_tray_3:
  friendly_name: "Spool Remaining Filament Tray 3"
  unit_of_measurement: '%'
  value_template: "{{ state_attr('sensor.X1C-ClumsysLab-1-AMS_Tray_3', 'Remaining filament') | float }}"
  spool_remaining_filament_tray_4:
  friendly_name: "Spool Remaining Filament Tray 4"
  unit_of_measurement: '%'
  value_template: "{{ state_attr('sensor.X1C-ClumsysLab-1-AMS_Tray_4', 'Remaining filament') | float }}"

[clumsyzombie]

I got it working thank you