Heidelberg Energy Control - RS485 to ETH Hutschienenmodul #2931
Replies: 9 comments 42 replies
-
Nein, passt nicht. Die seriellen Einstellungen des Konverters müssen exakt zu den Einstellungen der Box passen. Also 19200,8e1. Die Einstellungen in evcc gelten dann wiederum der Kommunikation mit dem Konverter. Also eher so ungefähr: chargers:
- name: Wallbox 2
type: heidelberg
uri: 192.168.178.182:502
rtu: true
id: 1 # configurable (S2/DIP 1)
# an evcc sponsortoken is required for using this charger |
Beta Was this translation helpful? Give feedback.
-
Warum muss ich den Port 502 angeben? Das Hutschienenmodul hört auf dem Port 4196. |
Beta Was this translation helpful? Give feedback.
-
Ich muss meinen Thread nochmal aufgreifen. Meine Frage ist nun, wie ich die Wallbox nun in der evcc.yaml eingebe. Momentan sieht es so aus.
Bei der Einstellung des Waveshare-Moduls blicke ich auch nicht so richtig durch.
Ich habe bereits die beiden Ports 4196 und 80 jeweils in Kombination mit allen Work-Modes ausprobiert. Alles mit dem Ergebnis, dass die Seite im Browser nicht startet. Mir fehlt gerader jeder Plan, wo ich noch weitersuchen kann. PS: Ich würde gerne noch einen Screenshot der Einstellungsoberfläche des Waveshare-Moduls anhängen. Wie geht das hier? |
Beta Was this translation helpful? Give feedback.
-
Ich glaube, ich habe es gefunden. Hatte zwei Punke jeweils mit Buchstaben-Drehern geschrieben. Hab auf jeden Fall herzlichen Dank für Deine schnelle Hilfe und einen schönen Sonntag Abend. |
Beta Was this translation helpful? Give feedback.
-
Hallo Zusammen,
Ich bekomme immer wieder den Fehler:
Zur Anmerkung oben:
Hmm, An der Heidelberg Wallbox habe ich den Widerstand per DIP geschaltet. Beste Grüße Andreas |
Beta Was this translation helpful? Give feedback.
-
@twingo667 Das wäre ja großartig, wenn es daran läge!! Du hast also den DIP-Widerstand wieder ausgeschaltet und einen separaten Abschlusswiderstand am Ende bei der Wallbox gesetzt. Richtig? |
Beta Was this translation helpful? Give feedback.
-
Hallo an alle, die das hier gelesen haben und mir Tipps gegeben haben! |
Beta Was this translation helpful? Give feedback.
-
Hi, Zusätzlicher Abschlusswiderstand an beide Enden: Wallbox und Waveshare. hier die Konfiguration aus der evcc.yaml:
|
Beta Was this translation helpful? Give feedback.
-
Hi, Hätte noch ein "Waveshare RS485 TO WIFI/ETH" von einem anderen (gescheiterten) Projekt hier liegen, aber die Benutzeroberfläche ist da sowas von wirr durch Wifi und ETH Kombination, dass ich überhaupt nicht mehr durchblicke was ich wo einstellen muss......!!?! Sollte also jemand das "Waveshare RS485 TO WIFI/ETH" am laufen haben, wäre ich dankbar über eine Bilderstrecke was man wo einstellen muss. Danke schon mal vorab Gruß |
Beta Was this translation helpful? Give feedback.
-
Guten Abend,
ich habe meine Heidelberg Energy Control über ein RS485 to ETH - Hutschienenmodul von Waveshare angeschlossen.
Die Box habe ich per DIP S2 auf Slave geschaltet. Das Hutschienenmodul ist im LAN erreichbar.
In der Einstellungoberfläche des Hutschienenmoduls habe ich den RS485 auf 19200 Baud, 8 Datenbits und Parity None Stopbits 0 gestellt.
Die Box habe ich in der evcc.yaml folgendermaßen konfiguriert:
Die Daten habe ich mir aus dem Forum zusammengesucht. Ich bin mir keinesfalls sicher, ob das alles so passt.
Wie kann ich nun überprüfen, ob die Wallbox vom EVCC erkannt wird und ansprechbar ist?
Weder auf der Seite, die der RasPi im System bekommen hat, noch mit dem Befehl
evcc -1 debug meter
kann ich eine Veränderung erkennen.
Ich habe bisher noch keinen Sponsor-Token, weil ich noch am Ausprobieren bin und auch noch keinen Liefertermin für's Auto habe. Sollte der aber an dieser Stelle essentiell sein, werde ich ihn natürlich lösen.
Vielen Dank schonmal für die Hilfe.
Beta Was this translation helpful? Give feedback.
All reactions