Add heatpump control #1875
Replies: 29 comments 124 replies
-
Interessante Idee. Dann wären wir allerdings eine Art SAE? Nicht unmöglich, aber doch ein wenig Aufwand. |
Beta Was this translation helpful? Give feedback.
-
Es macht halt schlussendlich nur Sinn alles gemeinsam zu Steuern. Wenn die Wärmepumpe nicht mit rein kommt wird es für immer mehr Leute dann halt nur begrenzt Sinn ergeben evcc-io zu nutzen, fände ich schade, da das Projekt ansonsten für mich ziemlich spannend aussieht. |
Beta Was this translation helpful? Give feedback.
-
Meine Hauptsteuerung ist bei mir Loxone. Die kennt auch die Wärmepumpe. Und evcc wird einfach per mqtt „eingebunden“. |
Beta Was this translation helpful? Give feedback.
-
@TheSpirit das kling sehr gut, kann man denn dann selbst den Kompromiss zwischen Heizen und Fahrzeug laden beeinflussen? |
Beta Was this translation helpful? Give feedback.
-
Du kannst einfach das Heizen selbst steuern und evcc nimmt die restliche Energie fürs Auto. Dafür ist der PV Modus da. |
Beta Was this translation helpful? Give feedback.
-
Das war auch mein Gedanke es mit einzubinden das man den Speicher heizen kann wenn PV Überschuss da ist. |
Beta Was this translation helpful? Give feedback.
-
Ich würde mir das Thema Wärmepumpe gerne mal genauer anschauen. Was wären da die Anforderungen und wie sehen die Schnittstellen aus? |
Beta Was this translation helpful? Give feedback.
-
Schnittstellen sind leider sehr unterschiedlich. Manche funktionieren über WLAN und brauchen dann so einen Tuya Adapter wie bei Home Assistant. Manche haben auch andere Schnittstellen. Tuya Adapter wäre auf jeden Fall interessant für viele günstige Geräte. |
Beta Was this translation helpful? Give feedback.
-
wäre es denkbar wenn mal diese Dinge alle abfängt in dem man EVCC einen maximal erlaubten Netzbezug gibt und alle nicht automotive Verbraucher mit einer anderen Lösung z.B. ioBroker, Loxone, Homebridge etc. steuert? Edit: Ebenfalls gut wäre, wenn EVCC dann den maximal vorgegebenen Netzbezug dann entsprechend auf die Ladepunkte verteilt. |
Beta Was this translation helpful? Give feedback.
-
Über die klassischen Klimaanlagen kann man kühlen und heizen. Grad wenn man eh Elektrizität übrig hat kann das ganz praktisch sein. In vielen älteren Gebäuden gibt es halt oft die Situation, dass eine Gasheizung um solche Ansätze erweitert wird. Im Sommer gibt es auch oft das Thema Pool Wärmepumpe und dann kann man auch teilweise mal verzichten wenn man grad den Strom anderweitig benötigt. Von daher muss eine generische Lösung her, jedes Haus ist da leicht anders eingerichtet. |
Beta Was this translation helpful? Give feedback.
-
@premultiply Wenn man es so löst dann ist die Frage wie gut man evcc in diese Lösung integrieren kann und ob man es dann überhaupt noch braucht(?) Ist die Philosophie so, nur weil der Name evcc ist, dass man keine weiteren Module einbauen sollte? Persönlich würde ich es jedenfalls bevorzugen nur eine Lösung zu verwenden die möglichst simpel sich um alle großen Verbraucher im kW Bereich kümmert. Das ist der Themenblock der für mich falls möglich gemeinsam gemanagt gehört. Am Ende müssen es aber diejenigen entscheiden die ihre Zeit in die Umsetzung investieren. |
Beta Was this translation helpful? Give feedback.
-
Ich sehe in der Steuerbarkeit meiner Wärmepumpe (Wolf CHA-10 Monoblock mit je 150l Speicher für Heizung und Warmwasser) in meiner Situation durchaus als sinnvoll an.
|
Beta Was this translation helpful? Give feedback.
-
Ich habe zwei Jahre intensiv beruflich an der Regelgung über SG-Ready gearbeitet und habe auch Workshops mit dem Bundesverband Wärmepumpe gemacht. Hier mal eine kurze Präsentation, wie man sinnvolle Regelparameter festlegen kann, so dass die Nutzung der SG-Ready-Schnittstelle Sinn ergibt. Ansteuern könnte man praktisch alle am Markt verfügbaren Wärmepumpen über SG-Ready wohl am einfachsten über einen Shelly. @andig und @premultiply : Wir können uns dazu gerne auch mal im Gespräch austauschen. |
Beta Was this translation helpful? Give feedback.
-
Hallo zusammen, sehr interessante Diskussion. Ich selber bin Automatisierer und sehe die Dinge gern praktisch.
Ich würde bei der Umsetzung auch gern mit helfen... soweit es möglich ist. Ich habe einen FHEM Server und eine Siemens SPS im Haus... :-) |
Beta Was this translation helpful? Give feedback.
-
Moin!
Ich hab bei uns einen 3EM eingebaut und fand es allein schon interessant,
darüber die Arbeit der WP besser beobachten zu können. Wir nutzen die
aktuell auch zum Kühlen über die Fußbodenheizung und für Warmwasser. Ich
habe Warmwasser per Zeitsteuerung nur in der Mittagszeit, aber wenn wir
über SG Ready das Signal geben, macht sie halt zu jeder Zeit Warmwasser.
Kühlen machen wir ausschließlich, wenn SG Ready Signal kommt.
Also zwingend brauchen tut man den 3em dafür nicht, aber ich hab zum
Beispiel auch erst darüber festgestellt, dass sie manchmal am takten war
und habe dann feinjustiert.
Ich würde es wieder tun, aber dir muss auch klar sein, dass es nur ein
Schritt in Optimierung und Eigenverbrauchssteigerung ist.
Weitere Fragen? :-)
lg
f
|
Beta Was this translation helpful? Give feedback.
-
Das wird immer interessanter hier! U.a. dieses Forum finde ich interessant: lg, |
Beta Was this translation helpful? Give feedback.
-
Hallo zusammen, SMA macht das auch schon: |
Beta Was this translation helpful? Give feedback.
-
Ich kann meine Tecalor Wärmepumpe über das zusätzliche "ISG Web" per Modbus steuern. Ich fände eine Integration in EVCC auch toll. Ich glaube es gibt viele die so etwas gerne hätten, aber es ist nur nicht so straight-forward wie bei Wallbox und E-Auto vermutlich. Warmwasser als kurzzeitig steuerbaren Verbraucher / Puffer fände ich da noch am einfachsten da man ihn m.E. relativ einfach mit einem Akku vergleichen kann. Bei der Fußbodenheizung/Estricherwärmung wird das Thema sicher komplexer, da man gegen/mit der Trägheit der Estrichtemperatur ein Raumtemperatur erhalten möchte. Das ganze Abhängig von der Aussentemperatur. |
Beta Was this translation helpful? Give feedback.
-
Meine Weishaupt hat einen SG Ready Kontakt. Daran hab ich einen Shelly1 dran, welcher von evcc angesteuert wird. Schau mal #3837 |
Beta Was this translation helpful? Give feedback.
-
Hallo! Gibt es hier was neues? Wenn ja wo kann ich mich einlesen? |
Beta Was this translation helpful? Give feedback.
-
Hallo in die Runde, ich habe eine Weishaupt BiBlock Wärmepumpe WBB20. Mit dem letzten Softwareupdate hat sie jetzt auch ein "Gaspedal" bekommen: Per Modbus TCP kann der Wärmepumpe, Datenpunkt 40002 (Holding R/W), (0 … 30.000 W) ein elektrischer Leistungswert vorgegeben werden, z. B. der PV- Überschuss zur kompletten Eigenstromnutzung. |
Beta Was this translation helpful? Give feedback.
-
Im Gegensatz zu Autos müssten die Statusausprägungen für Wärmepumpen etwas anders sein. Diese würde ich gerne einmal gemeinsam sammeln. Sammlung relevanter Statusausprägungen für Wärmepumpen:
Die Steuerung würde ich weiterhin auf die SG-Ready Funktion begrenzen. Dies bedeutet die Status 1-5 würden von der Wärmepumpe selbst bereitgestellt. Sollte ein PV Überschluss hinzukommen, kann die Wärmepumpe den SG-Readykontakt schalten und so Status 6 aktivieren. Wenn die Wärmepumpe dann startet, würden je nach verfügbaren Ausprägungen 8 oder 9 aktiv werden. Die Status 4,5,8 und 9 könnten ggf. auch mit einer Zweitstatusausprägung und entsprechender Kombination abgebildet werden. |
Beta Was this translation helpful? Give feedback.
-
Beta Was this translation helpful? Give feedback.
-
Ich denke da darf jeder Entscheiden für was er seinen Energieüberschuss einsetzt. Man kann ihn natürlich auch für 7ct einspeisen und Nachts mit schlechtem Wirkungsgrad für 38 ct/kWh nachheizen oder einfach tagsüber mit dem Heizstab auf 75 Grad aufheizen und die Wärmepumpe hat keine Abnutzung. Das ist für mich auch Umweltschutz wenn die Wärmepumpe länger hält.
Ich bin gerade dran, es so aufzusetzen, dass ich einen Dummy in FHEM habe, der von meiner Ladestation „Heizstab“ aus evcc mit Daten versorgt wird.
Wenn es vollständig läuft werde ich es posten.
Freundliche Grüße
Joachim Platzer
Am 11. Apr. 2024, 13:07 +0200 schrieb premultiply ***@***.***>:
… Auf diesen energiefressenden Schwachsinn hat die Welt echt noch gewartet... 😪
—
Reply to this email directly, view it on GitHub, or unsubscribe.
You are receiving this because you commented.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
Ich habe versucht meine LWZ 504 mit ISG web und EMI (über SEMP) in evcc zu integrieren. Leider klappt das noch nicht so ganz:
Vielleicht hat jemand eine Idee und kann mir helfen. Ich würde mir natürlich auch eine "native" Integration wünschen.
|
Beta Was this translation helpful? Give feedback.
-
Ich schließe mich mal dahingehend an, dass wir hier
Bin gespannt, wie man das am Ende "eintüten kann", oder sagen wir zumindest die BWWP (SG Ready), den Hausakku und die Elektrokarre. Einbau steht die Tage an und wir haben auch die Atlantic Explorer Bridge zur WLAN Anbindung und Fernsteuerung. |
Beta Was this translation helpful? Give feedback.
-
Im Prinzip finde ich eine Wärmenpumpen Steuerung eine gute Idee, aber ich zweifle daran ob es eine gute Vorgehensweise ist Wärmepumpen direkt auf evcc zu steuern. Wenn der "Typ: Custom" es zulässt Wärmerzeuger über Modbus oder HTTP zu steuern ist ja wunderbar. Aber ich denke sinnvoller und einfacher wäre es Heizprofile über evcc zu erzeugen. Diese könnten dann z.b. mit Home Assistant weiterverarbeitet werden und auf individuelle Wärmeerzeuger angepasst werde. Mit Heizprofilen meine ich im Prinzip Profile die Sollwerte von Wärmeerzeuger steuern. Im Prinzip könnte man dies auch jetzt schon machen, z.b. über einen MQTT oder Shelly Charger, aber halt nur mit einem Profil bzw. 2 (high / low) über den evcc/loadpoints/1/enabled schalter. Schön wäre es dies dynamischer zu haben indem ein Wert wie bei einer Wallbox in Ampere (über OCPP) auf die APT/MQTT Schnitstelle gelegt würde. Man kann das selber filtern welcher Wert wechlem Profil entspricht. Super Cool wäre es den Wert auch in der UI angezeigt zu haben. |
Beta Was this translation helpful? Give feedback.
-
Ich habe eine ältere Wärmepumpe die kein SG Ready kann. Ich habe also alle Rückmeldungen über Temperaturen oder sonstwas nur an der propritären Steuerung Im Heizungsraum die ich nicht fernsteuern kann und die auch keine Werte nach Aussen gibt. Auch den Stromverbrauch der WP kann ich nicht einsehen oder an EVCC weitergeben. Ich könnte sie also nur Blind steuern was aber besser ist als nix. Das einzige was sie extern kann ist auf die Sperre vom Netzbereiber zu reagieren. Ich kann sie damit nur An oder Ausmachen. Ich habe also einen Shelly dafür genutzt diesen Kontakt zu schalten: AUS = WP denkt Netzsperre, AN = normaler Betrieb. Manuell kann ich dadurch die WP immer aus Aus lassen und anmachen wenn Überschuss ist oder im WInter der Preis niedrig. Nun habe ich die als loadpoint eingebunden nach einer Anleitung die ich irgendwo im Netz gefunden habe. Und ich habe sie in der Reihenfolge der Loadpoint an die erste Stell gesetzt. Nur es scheint nicht zu funktionieren. Auch bei deutlich mehr als 2 KW Überschuss wird sie nicht angemacht. Es wird lieber das E-Auto mit 4-5 KW geladen. Ich kann sie aber manuell über EVCC an und ausschalten.
Wie kann ich das zum laufen bekommen? |
Beta Was this translation helpful? Give feedback.
-
Beta Was this translation helpful? Give feedback.
-
Some people also have a heatpump as part of their setup. Would it be possible to also ads control of those devices? That means we can control when the vehicle should be charged or when the home should be heated first.
Beta Was this translation helpful? Give feedback.
All reactions