Skip to content

Latest commit

 

History

History
106 lines (91 loc) · 5.39 KB

knownlimitations.md

File metadata and controls

106 lines (91 loc) · 5.39 KB
Raw

Known Limitations {#knownlimitations}

Some sensors do not work seamlessly with a specific board. This means that they are either incompatible or work only under specific settings. This is a list of such sensors and known workarounds if they exist.

Grove Sensors

  • RN2903 Click 2 version. This device will not work using the Edison UART on the Arduino breakout. It does work on Edison using a USB->serial interface.
  • Grove LCD RGB Backlit (JHD1313M1) requires 5V and should be used with an external power supply connected to the board to function properly. Although some high powered USB ports might be enough, in most cases you will encounter dropped characters, washed out text and/or failed I2C writes while using USB power alone.
  • Grove Servo (ES08A) requires an external power supply connected to the board to work. We highly recommend using a separate circuit when powering any sort of motor. Trying to use this servo off USB power alone can lead to damage to the servo and/or board!
  • Grove I2C Touch Sensor (MPR121) v1.3 is incompatible with the Intel Edison using the Arduino board, but will work with the Mini-breakout if supplied with at least 4V. Revision v1.2 works well on all Intel boards.
  • Grove Nunchuck only works with the Intel Galileo boards and is unusable on the Intel Edison boards.
  • Grove 3-Axis Digital Gyroscope (ITG-3200) is not compatible with the Intel Edison Arduino board but will work with the Mini-breakout.
  • Grove 3-Axis Digital Accelerometer +/-16g (ADXL345) only works with the Intel Edison Arduino board when powered from the 3.3V line.
  • Grove 3-Axis Digital Compass (HMC5883L) reports inaccurate values at 5V on the Intel Edison Arduino board and newer revisions might not work at all. Use 3.3V or the Mini-breakout.
  • Grove 96x96 OLED Display will not work on the Intel Edison with Arduino breakout.
  • Grove 128x64 OLED Display will not work on the Intel Edison with Arduino breakout.
  • Grove Barometer (BMP085) has an unstable connection on the Intel Edison using the Arduino breakout and may drop read data. The Xadow version of this sensor (BMP180) is also dropping data packets occasionally.
  • Grove 6-Axis Accelerometer & Compass (LSM303) fails to write to the configuration register properly and returns invalid data.
  • Grove I2C ADC Converter does not show up on the I2C bus on the Intel Edison with the Arduino board.
  • Grove I2C Motor Driver is not compatible with the Intel Galileo due to the inability to change the I2C bus speed to 100 KHz.
  • Grove Digital Light Sensor (TSL2561) may have an unstable connection on the Intel Edison using the Arduino breakout that results in missed I2C reads. This is usually applicable when the I2C lines are pulled-up to 5V. Works as expected with the Mini-breakout.
  • Grove CO2 Sensor will return zeroed data and is unusable on the Intel Galileo.
  • Grove BLE (HM-11) does not return data on the Intel Galileo board due to known UART limitation.
  • Grove Hall Sensor (A11X) if the base shield is set to 3V on Intel Edison, it will trigger continuous callbacks when the sensor is not reading anything.
  • Grove RTC (DS1307) is not compatible with the Intel Edison Arduino board but will work with the Mini-breakout.
  • Grove Temperature & Humidity (High-Accuracy & Mini) Sensor (TH02) only works with the Intel Edison Arduino board when powered from the 3.3V rail.

Adafruit Sensors

  • Adafruit Motor Shield (1438) is not detected on the I2C bus when connected to the Intel Edison with an Arduino breakout.

One Wire Sensors

Please note that our 1-Wire protocol implementation is only compatible with Dallas 1-Wire devices and uses both the RX and TX pins of a UART bus for communication. It will also require the following external circuit:

1-Wire Circuit Diagram

The principle of operation is discussed [here] (https://www.maximintegrated.com/en/app-notes/index.mvp/id/214). This affects the DS18B20, DS2413 and DFREC drivers.

Other Sensors

  • HTU21D is unstable on the Intel Edison with the Arduino breakout and will throw an error when it can't complete an update call.
  • MLX90614 is not compatible with the Intel Galileo due to the inability to change the I2C bus speed to 100 KHz.
  • MICSV89 is not compatible with the Intel Galileo due to the inability to change the I2C bus speed to 100 KHz.
  • MPL3115A2 uses repeated starts for I2C communication and may not work as expected especially when other I2C sensors are present on the same bus.
  • InvenSense MPU9150 & MPU9250 will be unable to report magnetometer data when used on the Intel Edison Arduino board because the integrated compass chips are not detected on the I2C bus.

General

Some I2C sensors add too much capacitance to the SDA line of the Intel Edison Arduino breakout board, thus the signal sticks to a logic 1. When this happens, other sensors connected to the I2C bus also become unusable. In order to solve this problem, an I2C repeater that isolates the capacitance on the bus, such as the PCA9517 can be used.

The Intel Edison SPI bus can corrupt data being sent across when certain sensors are connected to it, if using an old image. This has been resolved with the latest releases.

On the Intel Galileo boards, the UART bus might drop data if several bytes are read at once.