| layout | title |
|---|---|
documentation |
012501 - ZWave |
{% include base.html %}
This describes the Z-Wave device 012501, manufactured by Popp & Co with the thing type UID of popp_012501_00_000.
The device is in the category of Lock, defining Devices whose primary pupose is locking something.
The 012501 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is unable to participate in the routing of data from other devices.
An electric strike is an access control device used to lock and release doors. Electric strikes are installed in or on the doorframe and work in conjunction with mechanical door locks, on the principle of electronically controlling the rotation of the keeper. Allowing for door opening without manual retraction of the mechanical door lock. This product combines a 16 mm thick strike lock (that will fit into almost all door formats) with a Z-Wave plus empowered wireless control.
The lock mechanics and the Z-Wave control are operated by a 9V block battery or an external 8-12V AC / 8-24V DC transformer. The Z-Wave control accepts commands to open or close the strike. Depending on a configuration parameter the door will be looked automatically after a certain time even if no ‘close’ command was sent. According to the connected Z-Wave Gateway all actions of the Strike Lock will be recorded with a time stamp.
The device is a secure Z-Wave Plus device and can be used in one wireless Z-Wave network with other certified devices regardless of origin and brand. It supports secure communication if the central controller supports secure communication as well.
Pressing the Z-Wave button for one second includes the device.
It is not allowed to operate the device in a non-secure environment. This means that the including controller must support Secure Command Class.
A single click on the button will exclude the device.
The Strike-Lock has a IP 20 protection class. Because of that it is not recommended to install the device directly outdoors.
The following table summarises the channels available for the 012501 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Binary Sensor | sensor_binary | Door | Switch |
| Door Lock | lock_door | Door | Switch |
| Alarm (access) | alarm_access | Door | Switch |
| Alarm (general) | alarm_general | Door | Switch |
| Battery Level | battery-level | Battery | Number |
Indicates if a sensor has triggered.
The sensor_binary channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| ON | Triggered |
| OFF | Untriggered |
Lock and unlock the door.
The lock_door channel supports the Switch item and is in the Door category.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| ON | Locked |
| OFF | Unlocked |
Indicates if the access control alarm is triggered.
The alarm_access channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Indicates if an alarm is triggered.
The alarm_general channel supports the Switch item and is in the Door category. This is a read only channel so will only be updated following state changes from the device.
The following state translation is provided for this channel to the Switch item type -:
| Value | Label |
|---|---|
| OFF | OK |
| ON | Alarm |
Represents the battery level as a percentage (0-100%). Bindings for things supporting battery level in a different format (e.g. 4 levels) should convert to a percentage to provide a consistent battery level reading.
The battery-level channel supports the Number item and is in the Battery category.
The following table provides a summary of the 3 configuration parameters available in the 012501. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 0 | Auto-Close | Automated Close after Opening |
| 1 | Off-Command | Value of Off-Command |
| 2 | On-Command | Value of On-Command |
| Lock Timeout | Sets the time after which the door will auto lock |
Automated Close after Opening
0: No automated close after command ‘open’
1-127: Close again after x seconds (Default 3)
Values in the range 0 to 127 may be set.
The manufacturer defined default value is 3.
This parameter has the configuration ID config_0_1 and is of type INTEGER.
Value of Off-Command Value of Off-Command (Parameter number 1, Size 1) Values in the range 0 to 99 may be set.
The manufacturer defined default value is 0.
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Value of On-Command Value of On-Command (Parameter number 2, Size 1) Values in the range 0 to 99 may be set.
The manufacturer defined default value is 99.
This parameter has the configuration ID config_2_1 and is of type INTEGER.
Sets the time after which the door will auto lock.
This parameter has the configuration ID doorlock_timeout and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The 012501 supports 2 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation. Device status
Association group 1 supports 10 nodes.
Action on External Dry Input
Association group 2 supports 10 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SENSOR_BINARY_V2 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_DOOR_LOCK_V1 | |
| COMMAND_CLASS_USER_CODE_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_ALARM_V5 | Linked to BASIC |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_LOCK_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_BATTERY_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.