| layout | title |
|---|---|
documentation |
TPS411 - ZWave |
{% include base.html %}
This describes the Z-Wave device TPS411, manufactured by McoHome Technology Co., Ltd with the thing type UID of mcohome_tps411_00_000.
This version of the device is limited to firmware versions below 5.2
The device is in the category of Wall Switch, defining Any device attached to the wall that controls a binary status of something, for ex. a light switch.
The TPS411 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
Touch Panel Switch is a wall panel built-in with Z-Wave Plus module. With its stylish design and stable performance, the panel can be used to control house-hold electrical appliances like lamp, motor, coffee machine, TV set etc. It supports basic command class，multi channel command class and multi channel association command class, also works as a repeater in a Z-Wave network. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from any other manufacturers
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
To include the device you only need to press and hold any key for 8 seconds.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
To exclude the device you only need to press and hold any key for 3 seconds.
The actuator is operated by the local switching Touch pannels or wirelessly using Z-Wave commands.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
- Press and hold any key on the panel for 10 seconds for restoring factory settings.
- Then the node information and association data will be deleted.
**Note:**If factory settings are restored, all INDICATION LEDs on the panel will turn orange, and all switches will turn off.
The following table summarises the channels available for the TPS411 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Switch | switch_binary | Switch | Switch |
| Switch 1 | switch_binary1 | Switch | Switch |
Switch the power on and off.
The switch_binary channel supports the Switch item and is in the Switch category.
Switch the power on and off.
The switch_binary1 channel supports the Switch item and is in the Switch category.
The following table provides a summary of the 1 configuration parameters available in the TPS411. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 1 | Saving state before power failure | Switch state saved or not when power down |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
Switch state saved or not when power down
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
The manufacturer defined default value is 1 (Enabled).
This parameter has the configuration ID config_1_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The TPS411 supports 2 association groups.
Association group 1 supports 5 nodes.
Association group 2 supports 1 node.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_V2 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V1 | |
| COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2 |
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.