| layout | title |
|---|---|
documentation |
14288 - ZWave |
{% include base.html %}
This describes the Z-Wave device 14288, manufactured by Jasco Products with the thing type UID of ge_14288_00_000.
The 14288 supports routing. This allows the device to communicate using other routing enabled devices as intermediate routers. This device is also able to participate in the routing of data between other devices in the mesh network.
No device information is provided in the database. Consider updating the database to improve the documentation.
The following table summarises the channels available for the 14288 -:
| Channel | Channel Id | Category | Item Type |
|---|---|---|---|
| Switch | switch_binary | Switch | Switch |
| Scene Number | scene_number | Number |
Switch the power on and off.
The switch_binary channel supports the Switch item and is in the Switch category.
Triggers when a scene button is pressed.
The scene_number channel supports the Number item.
The following table provides a summary of the 1 configuration parameters available in the 14288. Detailed information on each parameter can be found in the sections below.
| Param | Name | Description |
|---|---|---|
| 3 | LED Light configuration | |
| Switch All Mode | Set the mode for the switch when receiving SWITCH ALL commands |
LED Light configuration 0 - LED On when load is Off, Led Off when load is On
1 - LED On when load is On, LED Off when laod is Off (Default)
2 - LED always off The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | LED On when load is Off, Led Off when load is On |
| 1 | LED On when load is On, LED Off when laod is Off (Default) |
| 2 | LED always off |
The manufacturer defined default value is 1 (LED On when load is On, LED Off when laod is Off (Default)).
This parameter has the configuration ID config_3_1 and is of type INTEGER.
Set the mode for the switch when receiving SWITCH ALL commands.
The following option values may be configured -:
| Value | Description |
|---|---|
| 0 | Exclude from All On and All Off groups |
| 1 | Include in All On group |
| 2 | Include in All Off group |
| 255 | Include in All On and All Off groups |
This parameter has the configuration ID switchall_mode and is of type INTEGER.
Association groups allow the device to send unsolicited reports to the controller, or other devices in the network. Using association groups can allow you to eliminate polling, providing instant feedback of a device state change without unnecessary network traffic.
The 14288 supports 3 association groups.
The Lifeline association group reports device status to a hub and is not designed to control other devices directly. When using the Lineline group with a hub, in most cases, only the lifeline group will need to be configured and normally the hub will perform this automatically during the device initialisation.
Association group 1 supports 5 nodes.
Supports Basic Set and is controlled with the local load
Association group 2 supports 5 nodes.
Supports Basic Set and is controlled by pressing the On or Off button
Association group 3 supports 5 nodes.
| Command Class | Comment |
|---|---|
| COMMAND_CLASS_NO_OPERATION_V1 | |
| COMMAND_CLASS_BASIC_V1 | |
| COMMAND_CLASS_SWITCH_BINARY_V1 | Linked to BASIC |
| COMMAND_CLASS_SWITCH_ALL_V1 | |
| COMMAND_CLASS_SCENE_ACTIVATION_V1 | |
| COMMAND_CLASS_SCENE_ACTUATOR_CONF_V1 | |
| COMMAND_CLASS_CRC_16_ENCAP_V1 | |
| COMMAND_CLASS_ASSOCIATION_GRP_INFO_V1 | |
| COMMAND_CLASS_DEVICE_RESET_LOCALLY_V1 | |
| COMMAND_CLASS_ZWAVEPLUS_INFO_V1 | |
| COMMAND_CLASS_CONFIGURATION_V1 | |
| COMMAND_CLASS_MANUFACTURER_SPECIFIC_V1 | |
| COMMAND_CLASS_POWERLEVEL_V1 | |
| COMMAND_CLASS_FIRMWARE_UPDATE_MD_V1 | |
| COMMAND_CLASS_ASSOCIATION_V2 | |
| COMMAND_CLASS_VERSION_V2 |
Did you spot an error in the above definition or want to improve the content? You can contribute to the database here.