open http://esp-ebus.local/param to adjust PWM value

[tomm10000]

Hello, Before uploading the software, I could set PWM, now I don't know how to enter this option.
I'm trying http://192.168.1.135/param but it doesn't work

[danielkucera]

Hello, which HW version do you have?

[tomm10000]

Hello, which HW version do you have?

HW 6.1

Chip ID: 543204b78c50, ESP32-C3, rev 4
Hostname: ebus-b78c50
PCB: 20.0
Flash: 4194304
Version: v5.2-dev-3318-g8fc8f3f479
Reset reason: 1
eBUS r/w: 1/0
Host r/w: 4/20
Up time: 216
Free heap: 99168
ebusd connected: yes (inactive)
eBUS signal: no signal

[danielkucera]

And which software did you upload?

[tomm10000]

Through this website, I guess that FW is not correct
https://adapter.ebusd.eu/v5/firmware.en.html

This one update? firmware-fullflash-HW_v5.x-be7bb3.bin
https://github.com/danielkucera/esp8266-arduino-ebus/releases

[danielkucera]

Yes, the first one is incorrect, completely different hardware.

Yes, use the one from releases on this page

[tomm10000]

Can I upload via USB-C? + NodeMCU PyFlasher

[tomm10000]

[tomm10000]

The jumper is also not understandable to me

power from any adapter 5-24V: remove jumper and connect adapter to VCC and GND pins

[danielkucera]

What is the question exactly?

[tomm10000]

Which pins are these?
using a wire connect pins PROG and TP3 ( TP3 ?? )
I don't understand it, different markings

connect your adaptor in a following way (dongle - module):
3V3 <-> 3V3
TX <-> ESP-RX
RX <-> ESP-TX
GND <-> GND

[danielkucera]

This is for the old version. For 6.1 just connect PROG and GND and flash over the USB-C port

[tomm10000]

edit
Okay, I think I understand, version 5 confused me

Now I'm crazy,I returned to the beginning and now I have to upload the software ?

@danielkucera
Thank you for your help

Adds a link to the page where you can upload the firmware firmware-fullflash-HW_v5.x-be7bb3.bin
Address 0x0

https://adafruit.github.io/Adafruit_WebSerial_ESPTool/

[danielkucera]

now I have to upload the software ?

What do you mean by this?

[tomm10000]

Does this software still require any update, because I only have this simple configuration panel

Now D1 works OK

device: 192.168.1.135:3333, TCP, enhanced
signal: acquired
symbol rate: 14
max symbol rate: 22
reconnects: 1
masters: 1
messages: 11
conditional: 0
poll: 0
update: 4
address 31: master #8, ebusd
address 36: slave #8, ebusd

root@raspberrypi:~# ebusctl find
broadcast datetime = no data stored
broadcast error = no data stored
broadcast id = no data stored
broadcast id = no data stored
broadcast signoflife = no data stored
memory eeprom = no data stored
memory ram = no data stored

https://github.com/guillaumezin/DomoticzEbusd

I'm trying to download data to domotich with this plugin

[danielkucera]

It's all there is. You will need to setup ebusd to connect to your adapter to decode the data.

[tomm10000]

It's all there is. You will need to setup ebusd to connect to your adapter to decode the data.

Thank you
There is a connection :-)

root@raspberrypi:~# ebusctl info
version: ebusd 23.3.23.3-29-g2ea20ed8
device: 192.168.1.135:3335, TCP, enhanced
signal: acquired
symbol rate: 25
max symbol rate: 25
reconnects: 0
masters: 3
messages: 11
conditional: 0
poll: 0
update: 4
address 03: master #11
address 08: slave #11
address 10: master #2
address 31: master #8, ebusd
address 36: slave #8, ebusd

root@raspberrypi:~# ebusctl scan result
08;Vaillant;BAI00;0600;5502
15;Vaillant;47000;0130;6002;21;12;49;0020108131;0082;011388;N2