-
Notifications
You must be signed in to change notification settings - Fork 20
/
INSTALL
267 lines (176 loc) · 9.8 KB
/
INSTALL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
Preliminary Mininet Installation/Configuration Notes
Mininet 1.0rc0
---
The supported installation methods for Mininet are 1) using
a pre-built VM image, and 2) native installation on Ubuntu or Debian.
(Other distributions may be supported in the future - if you would
like to contribute an installation script, we would welcome it!)
1. Easiest "install" - use our pre-built VM image!
The easiest way to get Mininet running is to start with one of our pre-built
virtual machine images from http://openflow.org/mininet
Boot up the VM image, log in, and follow the instructions on the wiki page.
An additional advantage of using the VM image is that it doesn't mess with
your native OS installation or damage it in any way.
2. Native installation (experimental!) for Ubuntu and Debian 5
If you are running Ubuntu or Debian 5, you may be able to use our handy
install.sh script, which is in mininet/util.
WARNING: USE AT YOUR OWN RISK!
install.sh is a bit intrusive and may possibly damage your OS
and/or home directory. Although we hope it won't do anything completely
terrible, you may want to look at the script before you run it, and you
should make sure your system and home directory are backed up just in case!
To install ALL of the software which we use for OpenFlow tutorials, you may
use
$ mininet/util/install.sh
This takes about 20-30 minutes.
Alternately, you can install just the pieces you need.
We recommend the following steps, in order:
a) On Debian 5, first install a Mininet-compatible kernel:
$ mininet/util/install.sh -k
Reboot and run 'uname -r' to make sure you're running the new kernel.
b) Install mininet and its dependencies:
$ mininet/util/install.sh -n
c) Install OpenFlow 1.0 and associated useful software
$ mininet/util/install.sh -f
d) Install Open vSwitch and its kernel module
$ mininet/util/install.sh -vm
e) If you wish to install the version of NOX we use in the tutorial:
$ mininet/util/install.sh -x
Good luck! Some additional installation notes are provided below, for
the brave and/or Linux-savvy, or those who are trying to understand what
is installed and why.
p.s. Note that only one instance of Mininet is currently supported on a single
machine - that's one reason we recommend using a VM to run it.
---
Mininet Manual Installation Notes
These installation notes assume you understand how to do things like
compile kernels, apply patches, configure networks, write code, etc.. If
this is unfamiliar territory, or if you run into trouble, we recommend
using one of our pre-built virtual machine images (see above.)
If you wish to try to create a VM to run Mininet, you may also wish
to look at the Wiki page:
http://openflow.org/foswiki/bin/view/OpenFlow/MininetVMCreationNotes
0. Obtaining Mininet
If you're reading this, you've already done it, but the command to
download mininet is:
git clone git://openflow.org/mininet.git
1. Core Mininet installation
The core Mininet installation requires gcc, make, python,
and setuptools. On Ubuntu and Debian you may install them with:
# aptitude install gcc make python setuptools
To install Mininet itself, with root privileges:
# cd mininet
# make install
This places the mininet package in /usr/lib/python-*/site-packages/,
so that 'import mininet' will work, and installs the primary mn
script (mn) as well as its helper utility (mnexec.)
On Ubuntu and Debian, Mininet's dependencies and core files may also be
installed using mininet/util/install.sh -n
2. Installation script for Ubuntu/Debian Lenny
If you are running Ubuntu 10.04 or Debian Lenny, you may be able to use the
util/install.sh script to install a compatible Linux kernel as well as
other software including the OpenFlow reference implementation, the Open
vSwitch switch implementation, and the NOX OpenFlow controller.
Many different installation options are possible by passing different
options to install.sh; install.sh -h lists them all.
Assuming the mininet source tree is installed in ~/mininet, the steps to run
install.sh to install EVERYTHING we use for OpenFlow tutorials are:
% cd
% time ~/mininet/util/install.sh # installs tons of stuff
% sudo reboot # to load new kernel
% ~/mininet/util/install.sh -c # to clean out unneeded kernel stuff
This installs a lot of useful software, but it will take a while (30
minutes or more, depending on your network connection, computer, etc..)
Probably the minimal semi-useful configuration would be to install
Mininet itself, kernel support if necessary, and either the
reference OpenFlow switch or Open vSwitch. This could be installed
as follows:
% sudo ~/mininet/util/install.sh -knvm
Respectively, this installs kernel support, core mininet dependencies,
Open vSwitch, and the Open vSwitch kernel module. If a new kernel was
installed, then a reboot may be required.
If install.sh cannot be used for some reason (e.g. you're on Fedora
or some other Linux - please don't say CentOS) or if you don't want to
install all of these components (they're useful!), the kernel and
OpenFlow software requirements are described in steps [3] and [4],
which follow.
If you successfully used install.sh, congratulations! You're basically
done. Proceed to step [6] for additional advice.
3. Linux Kernel requirements
Mininet requires a kernel built with network namespace support enabled,
i.e. with CONFIG_NET_NS=Y, such as the kernel shipped with
Ubuntu 10.04 LTS, currently 2.6.32. On Ubuntu 10.04, you should not need
to install or build a custom kernel, although 2.6.33+ is faster at
tearing down virtual ethernet pairs.
For Ubuntu and Debian, we provide a 2.6.33 kernel package which you may be
able to install using "util/install.sh -k". Note our kernel package
requires an ext2 or ext3 root file system, so it won't work if you have
a default Ubuntu install, which uses ext4.
If your kernel wasn't compiled with CONFIG_NET_NS=Y, you will need to
build and install a kernel that does! >= 2.6.33 works better, but may
be harder to get working, depending on your Linux distribution.
A script for building Debian packages for 2.6.33.1 is provided in
mininet/util/kbuild. You may wish to read it, as it applies patches
to enable 2.6.33.1 to build under debian-stable, and to enable the
tun driver to work correctly with Mininet.
Earlier kernels (e.g. 2.6.29) work with CONFIG_NET_NS enabled and no
additional patches, but are much slower at removing veth interfaces,
resulting in much slower switch shutdown.
For scalable configurations, you might need to increase some of your
kernel limits. Sample params are in util/sysctl_addon, which can be
appended to /etc/sysctl.conf (and modified as necessary for your
desired configuration):
sudo su -c "cat sysctl_addon >> /etc/sysctl.conf"
To save the config change, run:
sudo sysctl -p
4. OpenFlow software and configuration requirements
Mininet requires either the reference OpenFlow switch implementation
(from openflowswitch.org) or Open vSwitch (openvswitch.org) to be
installed. "make test" requires the reference user space
implementations as well as Open vSwitch. Note the reference kernel
implementation is not currently included in OpenFlow 1.0.
On Ubuntu and Debian, the install.sh script may be used with the '-f'
option to install the OpenFlow reference implementation, the '-v' option
to build Open vSwitch, and the '-m' option to install the Open vSwitch
kernel module into /lib/modules (note: you must build Open vSwitch first!)
Mininet will automatically load and remove kernel module dependencies
for supported switch types, using modprobe and rmmod - but these
modules must be in a location where modprobe can find them (e.g.
something like /lib/modules/`uname -r`/kernel/drivers/net/)
The reference OpenFlow controller (controller(8)) only supports 16
switches by default! If you wish to run a network with more than 16
switches, please recompile controller(8) with larger limits, or use a
different controller such as nox. A patch to controller(8) is included
as util/openflow-patches/controller.patch.
5. Other software dependencies
On Ubuntu and Debian, other Mininet dependencies may be installed using
the '-n' option of the install.sh script.
To run the iperf test, you need to install iperf:
sudo aptitude/yum install iperf
We assume you already have ping installed. ;-)
To use xterm or sshd with Mininet, you need the following:
sudo aptitude/yum install sshd xterm screen
Some examples may have additional requirements - consult the specific
example file for details.
The install.sh script has an '-x' option to install the version of
NOX from the OpenFlow tutorial.
6. Other notes and recommendations
If you did not install certain useful packages and you wish to later,
it may be possible to install them using install.sh.
Mininet should be run either on a machine with
no other important processes, or on a virtual machine (recommended!)
Multiple concurrent Mininet instances are not supported!
Good luck!
---
Historical information on OpenFlow 0.8.9 and the reference kernel module:
The kernel reference implementation has been deprecated, but it may
be possible to get it work with Mininet.
To switch to the most recent OpenFlow 0.8.9 release branch (the most
recent one with full NOX support and kernel datapath support) in your
OpenFlow git tree:
git checkout -b release/0.8.9 remotes/origin/release/0.8.9
A patch to enable datapath.c to compile with recent kernels
is included in util/openflow-patches/datapath.patch.
In OpenFlow 1.0, switch port numbering starts at 1 (for better or for worse.)
To run with previous versions of OpenFlow, it may be necessary
to change SWITCH_PORT_BASE from 1 to 0 in node.py.