Try to compile a version für Sonoff NSPanel but failed!! TasmoCompiler v10-development #333

Mark-Muc · 2023-02-15T12:20:08Z

Mark-Muc
Feb 15, 2023

Hello I tried to compile a newer version of Sonoff NSPAnel in development brache.

TasmoCompiler v10-development

using this switches ..

Parameters:

#define FIRMWARE_NSPANEL
#define FRAMEWORK_ARDUINO_ITEAD

#define USE_THERMOSTAT                           
    #define THERMOSTAT_CONTROLLER_OUTPUTS         1  
    #define THERMOSTAT_SENSOR_NAME                "ANALOG"

    #define THERMOSTAT_SENSOR_NUMBER              1         
    #define THERMOSTAT_RELAY_NUMBER               1         
    #define THERMOSTAT_SWITCH_NUMBER              1         // Default input switch number for the first controller (+i for following ones)
    #define THERMOSTAT_TIME_ALLOW_RAMPUP          300       // Default time after last target update to allow ramp-up controller phase in minutes
    #define THERMOSTAT_TIME_RAMPUP_MAX            960       // Default time maximum ramp-up controller duration in minutes
    #define THERMOSTAT_TIME_RAMPUP_CYCLE          30        // Default time ramp-up cycle in minutes
    #define THERMOSTAT_TIME_SENS_LOST             30        // Maximum time w/o sensor update to set it as lost in minutes
    #define THERMOSTAT_TEMP_SENS_NUMBER           1         // Default temperature sensor number
    #define THERMOSTAT_TIME_MANUAL_TO_AUTO        60        // Default time without input switch active to change from manual to automatic in minutes
    #define THERMOSTAT_TIME_RESET                 12000     // Default reset time of the PI controller in seconds
    #define THERMOSTAT_TIME_PI_CYCLE              30        // Default cycle time for the thermostat controller in minutes
    #define THERMOSTAT_TIME_MAX_ACTION            20        // Default maximum thermostat time per cycle in minutes
    #define THERMOSTAT_TIME_MIN_ACTION            4         // Default minimum thermostat time per cycle in minutes
    #define THERMOSTAT_TIME_MIN_TURNOFF_ACTION    3         // Default minimum turnoff time in minutes, below it the thermostat will be held on
    #define THERMOSTAT_PROP_BAND                  4         // Default proportional band of the PI controller in degrees celsius
    #define THERMOSTAT_TEMP_RESET_ANTI_WINDUP     8         // Default range where reset antiwindup is disabled, in tenths of degrees celsius
    #define THERMOSTAT_TEMP_HYSTERESIS            1         // Default range hysteresis for temperature PI controller, in tenths of degrees celsius
    #define THERMOSTAT_TEMP_FROST_PROTECT         40        // Default minimum temperature for frost protection, in tenths of degrees celsius
    #define THERMOSTAT_TEMP_RAMPUP_DELTA_IN       4         // Default minimum delta temperature to target to get into rampup mode, in tenths of degrees celsius
    #define THERMOSTAT_TEMP_RAMPUP_DELTA_OUT      2         // Default minimum delta temperature to target to get out of the rampup mode, in tenths of degrees celsius
    #define THERMOSTAT_TEMP_PI_RAMPUP_ACC_E       200       // Default accumulated error when switching from ramp-up controller to PI in hundredths of degrees celsius
    #define THERMOSTAT_TIME_OUTPUT_DELAY          180       // Default output delay between state change and real actuation event (f.i. valve open/closed)
    #define THERMOSTAT_TEMP_INIT                  180       // Default init target temperature for the thermostat controller
    #define THERMOSTAT_TIME_MAX_OUTPUT_INCONSIST  3         // Default maximum time where the input and the output shall differ (for diagnostic) in minutes
    #define THERMOSTAT_TIME_MAX_AUTOTUNE          21600     // Maximum time for the PI autotune function to complete in seconds
    #define THERMOSTAT_DUTYCYCLE_AUTOTUNE         35        // Default duty cycle (in % over PI cycle time) for the step response of the autotune PI function
    #define THERMOSTAT_PEAKNUMBER_AUTOTUNE        8         // Default number of peak temperatures (max or min) to be used for the autotune PI function
    #define THERMOSTAT_TEMP_BAND_NO_PEAK_DET      1         // Default temperature band in thenths of degrees celsius within no peak will be detected
    #define THERMOSTAT_TIME_STD_DEV_PEAK_DET_OK   10        // Default standard deviation in minutes of the oscillation periods within the peak detection is successful    


#ifdef LATITUDE
  #undef LATITUDE
#endif
#define LATITUDE 48.105061

#ifdef LONGITUDE
  #undef LONGITUDE
#endif
#define LONGITUDE 11.518246

#ifdef APP_TIMEZONE
  #undef APP_TIMEZONE
#endif
#define APP_TIMEZONE 99

#ifdef USE_EXPRESSION 
#undef USE_EXPRESSION
#endif
#define USE_EXPRESSION

#ifdef SUPPORT_IF_STATEMENT
#undef SUPPORT_IF_STATEMENT
#endif
#define SUPPORT_IF_STATEMENT

it runs for the first time but then an error occured:

Linking .pio/build/tasmota32/firmware.elf
/tmp/Tasmota/tasmota/tasmota_xsns_sensor/xsns_62_esp32_mi_ble.ino: In function 'HandleMI32Key':
/tmp/Tasmota/tasmota/tasmota_xsns_sensor/xsns_62_esp32_mi_ble.ino:2672:10: warning: 'strncat' specified bound 64 equals destination size [-Wstringop-overflow=]
   strncat(key, mac, sizeof(key));
          ^
/home/gitpod/.platformio/packages/toolchain-xtensa-esp32/bin/../lib/gcc/xtensa-esp32-elf/8.4.0/../../../../xtensa-esp32-elf/bin/ld: .pio/build/tasmota32/firmware.elf section `.iram0.text' will not fit in region `iram0_0_seg'
/home/gitpod/.platformio/packages/toolchain-xtensa-esp32/bin/../lib/gcc/xtensa-esp32-elf/8.4.0/../../../../xtensa-esp32-elf/bin/ld: IRAM0 segment data does not fit.
/home/gitpod/.platformio/packages/toolchain-xtensa-esp32/bin/../lib/gcc/xtensa-esp32-elf/8.4.0/../../../../xtensa-esp32-elf/bin/ld: region `iram0_0_seg' overflowed by 32 bytes
collect2: error: ld returned 1 exit status
*** [.pio/build/tasmota32/firmware.elf] Error 1
========================= [FAILED] Took 292.71 seconds =========================

Environment    Status    Duration
-------------  --------  ------------
tasmota32      FAILED    00:04:52.705
==================== 1 failed, 0 succeeded in 00:04:52.705 ====================
Finished. Exit code: 1.

Anyone had a clue what happens?
Regards
Msrk_Muc

PS: I today tried to comile with the stable version and it worked!!

Today I tried to compile with TasmoCompiler v10.2.0 (final 12.4.0) and now I can't comple no version
Same Error:

Linking .pio/build/tasmota32/firmware.elf
/tmp/Tasmota/tasmota/tasmota_xsns_sensor/xsns_62_esp32_mi_ble.ino: In function 'HandleMI32Key':
/tmp/Tasmota/tasmota/tasmota_xsns_sensor/xsns_62_esp32_mi_ble.ino:2672:10: warning: 'strncat' specified bound 64 equals destination size [-Wstringop-overflow=]
   strncat(key, mac, sizeof(key));
          ^
/home/gitpod/.platformio/packages/toolchain-xtensa-esp32/bin/../lib/gcc/xtensa-esp32-elf/8.4.0/../../../../xtensa-esp32-elf/bin/ld: .pio/build/tasmota32/firmware.elf section `.iram0.text' will not fit in region `iram0_0_seg'
/home/gitpod/.platformio/packages/toolchain-xtensa-esp32/bin/../lib/gcc/xtensa-esp32-elf/8.4.0/../../../../xtensa-esp32-elf/bin/ld: IRAM0 segment data does not fit.
/home/gitpod/.platformio/packages/toolchain-xtensa-esp32/bin/../lib/gcc/xtensa-esp32-elf/8.4.0/../../../../xtensa-esp32-elf/bin/ld: region `iram0_0_seg' overflowed by 32 bytes
collect2: error: ld returned 1 exit status
*** [.pio/build/tasmota32/firmware.elf] Error 1
========================= [FAILED] Took 230.40 seconds =========================

Environment    Status    Duration
-------------  --------  ------------
tasmota32      FAILED    00:03:50.399
==================== 1 failed, 0 succeeded in 00:03:50.399 ====================
Finished. Exit code: 1.

benzino77 · 2023-02-28T17:58:48Z

benzino77
Feb 28, 2023
Maintainer

I think you shouldn't use #define FIRMWARE_NSPANEL or #define FIRMWARE_TASMOTA32
Instead you should try to define all features which are used to build this binary. Have a look here: link

I can't remember where, but @Jason2866 has mentioned in some place that using #define FIRMWARE_* in your user_config_override.h file may lead to problems and errors during compilation (customizations make by TasmoCompiler are mainly based on user_config_override.h file)

0 replies

Jason2866 · 2023-02-28T18:16:32Z

Jason2866
Feb 28, 2023

Should work (don't know what TasmoCompiler does...). The issue looks like running out of free ram.
BLE needs a lot. There is not much headroom left.
Try a build without Bluetooth. If this is working you know it is too BIG what you want to include.
The #define FIRMWARE_NSPANEL does include EVERYTHING what firmware Tasmota32 has on board.
So it is not a good idea to use together with TasmoCompiler

1 reply

Mark-Muc Mar 1, 2023
Author

Thx Jason2866!!
U'r right .. building a version without Bluetooth will built the version without problems!!
The problem is: I have to use BlueTooth because I use a BlueTooth Thermometer to control the Thermostat..
So what to do??
Regards
Mark

BTW: up to Version 12.3.1 to worked!!
Probem exist since 12.4.0

Jason2866 · 2023-03-01T08:45:12Z

Jason2866
Mar 1, 2023

Read the sevond part of my post. Do not use the define NSPanel.
Not a problem of 12.4. Tasmota has more features in standard setup

1 reply

Mark-Muc Mar 1, 2023
Author

oh excuse me .. I did not defining _#define FIRMWARE_NSPANEL_
what's about: #define FRAMEWORK_ARDUINO_ITEAD also not needed?

so no it compiles without any error and seems to work as expecteed ....
THX again for your help!!
Regards
Mark

Jason2866 · 2023-03-01T12:31:06Z

Jason2866
Mar 1, 2023

@Mark-Muc #define FRAMEWORK_ARDUINO_ITEAD is needed to select the modified framework for ITEAD.
Without the PSRAM will not work.

P.S. Grüsse nach Obersendling

1 reply

Mark-Muc Mar 1, 2023
Author

Danke Danke!!

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Try to compile a version für Sonoff NSPanel but failed!! TasmoCompiler v10-development #333

{{title}}

{{editor}}'s edit

{{editor}}'s edit

Replies: 4 comments 3 replies

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

Select a reply

Try to compile a version für Sonoff NSPanel but failed!! TasmoCompiler v10-development #333

Mark-Muc Feb 15, 2023

Replies: 4 comments · 3 replies

benzino77 Feb 28, 2023 Maintainer

Jason2866 Feb 28, 2023

Mark-Muc Mar 1, 2023 Author

Jason2866 Mar 1, 2023

Mark-Muc Mar 1, 2023 Author

Jason2866 Mar 1, 2023

Mark-Muc Mar 1, 2023 Author

Mark-Muc
Feb 15, 2023

Replies: 4 comments 3 replies

benzino77
Feb 28, 2023
Maintainer

Jason2866
Feb 28, 2023

Mark-Muc Mar 1, 2023
Author

Jason2866
Mar 1, 2023

Mark-Muc Mar 1, 2023
Author

Jason2866
Mar 1, 2023

Mark-Muc Mar 1, 2023
Author