forked from adafruit/Adafruit_L3GD20_U
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathAdafruit_L3GD20_U.cpp
362 lines (320 loc) · 12.6 KB
/
Adafruit_L3GD20_U.cpp
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
/***************************************************
This is a library for the L3GD20 GYROSCOPE
Designed specifically to work with the Adafruit L3GD20 Breakout
----> https://www.adafruit.com/products/1032
These sensors use I2C or SPI to communicate, 2 pins (I2C)
or 4 pins (SPI) are required to interface.
Adafruit invests time and resources providing this open source code,
please support Adafruit and open-source hardware by purchasing
products from Adafruit!
Written by Kevin "KTOWN" Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
****************************************************/
#if ARDUINO >= 100
#include "Arduino.h"
#else
#include "WProgram.h"
#endif
#include <Wire.h>
#include <limits.h>
#include "Adafruit_L3GD20_U.h"
/***************************************************************************
PRIVATE FUNCTIONS
***************************************************************************/
/**************************************************************************/
/*!
@brief Abstract away platform differences in Arduino wire library
*/
/**************************************************************************/
void Adafruit_L3GD20_Unified::write8(byte reg, byte value)
{
Wire.beginTransmission(L3GD20_ADDRESS);
#if ARDUINO >= 100
Wire.write((uint8_t)reg);
Wire.write((uint8_t)value);
#else
Wire.send(reg);
Wire.send(value);
#endif
Wire.endTransmission();
}
/**************************************************************************/
/*!
@brief Abstract away platform differences in Arduino wire library
*/
/**************************************************************************/
byte Adafruit_L3GD20_Unified::read8(byte reg)
{
byte value;
Wire.beginTransmission((byte)L3GD20_ADDRESS);
#if ARDUINO >= 100
Wire.write((uint8_t)reg);
#else
Wire.send(reg);
#endif
Wire.endTransmission();
Wire.requestFrom((byte)L3GD20_ADDRESS, (byte)1);
while (!Wire.available()); // Wait for data to arrive.
#if ARDUINO >= 100
value = Wire.read();
#else
value = Wire.receive();
#endif
Wire.endTransmission();
return value;
}
/***************************************************************************
CONSTRUCTOR
***************************************************************************/
/**************************************************************************/
/*!
@brief Instantiates a new Adafruit_L3GD20_Unified class
*/
/**************************************************************************/
Adafruit_L3GD20_Unified::Adafruit_L3GD20_Unified(int32_t sensorID) {
_sensorID = sensorID;
_autoRangeEnabled = false;
}
/***************************************************************************
PUBLIC FUNCTIONS
***************************************************************************/
/**************************************************************************/
/*!
@brief Setups the HW
*/
/**************************************************************************/
bool Adafruit_L3GD20_Unified::begin(gyroRange_t rng)
{
/* Enable I2C */
Wire.begin();
/* Set the range the an appropriate value */
_range = rng;
/* Make sure we have the correct chip ID since this checks
for correct address and that the IC is properly connected */
uint8_t id = read8(GYRO_REGISTER_WHO_AM_I);
//Serial.println(id, HEX);
if ((id != L3GD20_ID) && (id != L3GD20H_ID))
{
return false;
}
/* Set CTRL_REG1 (0x20)
====================================================================
BIT Symbol Description Default
--- ------ --------------------------------------------- -------
7-6 DR1/0 Output data rate 00
5-4 BW1/0 Bandwidth selection 00
3 PD 0 = Power-down mode, 1 = normal/sleep mode 0
2 ZEN Z-axis enable (0 = disabled, 1 = enabled) 1
1 YEN Y-axis enable (0 = disabled, 1 = enabled) 1
0 XEN X-axis enable (0 = disabled, 1 = enabled) 1 */
/* Reset then switch to normal mode and enable all three channels */
write8(GYRO_REGISTER_CTRL_REG1, 0x00);
write8(GYRO_REGISTER_CTRL_REG1, 0x0F);
/* ------------------------------------------------------------------ */
/* Set CTRL_REG2 (0x21)
====================================================================
BIT Symbol Description Default
--- ------ --------------------------------------------- -------
5-4 HPM1/0 High-pass filter mode selection 00
3-0 HPCF3..0 High-pass filter cutoff frequency selection 0000 */
/* Nothing to do ... keep default values */
/* ------------------------------------------------------------------ */
/* Set CTRL_REG3 (0x22)
====================================================================
BIT Symbol Description Default
--- ------ --------------------------------------------- -------
7 I1_Int1 Interrupt enable on INT1 (0=disable,1=enable) 0
6 I1_Boot Boot status on INT1 (0=disable,1=enable) 0
5 H-Lactive Interrupt active config on INT1 (0=high,1=low) 0
4 PP_OD Push-Pull/Open-Drain (0=PP, 1=OD) 0
3 I2_DRDY Data ready on DRDY/INT2 (0=disable,1=enable) 0
2 I2_WTM FIFO wtrmrk int on DRDY/INT2 (0=dsbl,1=enbl) 0
1 I2_ORun FIFO overrun int on DRDY/INT2 (0=dsbl,1=enbl) 0
0 I2_Empty FIFI empty int on DRDY/INT2 (0=dsbl,1=enbl) 0 */
/* Nothing to do ... keep default values */
/* ------------------------------------------------------------------ */
/* Set CTRL_REG4 (0x23)
====================================================================
BIT Symbol Description Default
--- ------ --------------------------------------------- -------
7 BDU Block Data Update (0=continuous, 1=LSB/MSB) 0
6 BLE Big/Little-Endian (0=Data LSB, 1=Data MSB) 0
5-4 FS1/0 Full scale selection 00
00 = 250 dps
01 = 500 dps
10 = 2000 dps
11 = 2000 dps
0 SIM SPI Mode (0=4-wire, 1=3-wire) 0 */
/* Adjust resolution if requested */
switch(_range)
{
case GYRO_RANGE_250DPS:
write8(GYRO_REGISTER_CTRL_REG4, 0x00);
break;
case GYRO_RANGE_500DPS:
write8(GYRO_REGISTER_CTRL_REG4, 0x10);
break;
case GYRO_RANGE_2000DPS:
write8(GYRO_REGISTER_CTRL_REG4, 0x20);
break;
}
/* ------------------------------------------------------------------ */
/* Set CTRL_REG5 (0x24)
====================================================================
BIT Symbol Description Default
--- ------ --------------------------------------------- -------
7 BOOT Reboot memory content (0=normal, 1=reboot) 0
6 FIFO_EN FIFO enable (0=FIFO disable, 1=enable) 0
4 HPen High-pass filter enable (0=disable,1=enable) 0
3-2 INT1_SEL INT1 Selection config 00
1-0 OUT_SEL Out selection config 00 */
/* Nothing to do ... keep default values */
/* ------------------------------------------------------------------ */
return true;
}
/**************************************************************************/
/*!
@brief Enables or disables auto-ranging
*/
/**************************************************************************/
void Adafruit_L3GD20_Unified::enableAutoRange(bool enabled)
{
_autoRangeEnabled = enabled;
}
/**************************************************************************/
/*!
@brief Gets the most recent sensor event
*/
/**************************************************************************/
void Adafruit_L3GD20_Unified::getEvent(sensors_event_t* event)
{
bool readingValid = false;
/* Clear the event */
memset(event, 0, sizeof(sensors_event_t));
event->version = sizeof(sensors_event_t);
event->sensor_id = _sensorID;
event->type = SENSOR_TYPE_GYROSCOPE;
while(!readingValid)
{
event->timestamp = millis();
/* Read 6 bytes from the sensor */
Wire.beginTransmission((byte)L3GD20_ADDRESS);
#if ARDUINO >= 100
Wire.write(GYRO_REGISTER_OUT_X_L | 0x80);
#else
Wire.send(GYRO_REGISTER_OUT_X_L | 0x80);
#endif
Wire.endTransmission();
Wire.requestFrom((byte)L3GD20_ADDRESS, (byte)6);
/* Wait around until enough data is available */
while (Wire.available() < 6);
#if ARDUINO >= 100
uint8_t xlo = Wire.read();
uint8_t xhi = Wire.read();
uint8_t ylo = Wire.read();
uint8_t yhi = Wire.read();
uint8_t zlo = Wire.read();
uint8_t zhi = Wire.read();
#else
uint8_t xlo = Wire.receive();
uint8_t xhi = Wire.receive();
uint8_t ylo = Wire.receive();
uint8_t yhi = Wire.receive();
uint8_t zlo = Wire.receive();
uint8_t zhi = Wire.receive();
#endif
/* Shift values to create properly formed integer (low byte first) */
event->gyro.x = (int16_t)(xlo | (xhi << 8));
event->gyro.y = (int16_t)(ylo | (yhi << 8));
event->gyro.z = (int16_t)(zlo | (zhi << 8));
/* Make sure the sensor isn't saturating if auto-ranging is enabled */
if (!_autoRangeEnabled)
{
readingValid = true;
}
else
{
/* Check if the sensor is saturating or not */
if ( (event->gyro.x >= 32760) | (event->gyro.x <= -32760) |
(event->gyro.y >= 32760) | (event->gyro.y <= -32760) |
(event->gyro.z >= 32760) | (event->gyro.z <= -32760) )
{
/* Saturating .... increase the range if we can */
switch(_range)
{
case GYRO_RANGE_500DPS:
/* Push the range up to 2000dps */
_range = GYRO_RANGE_2000DPS;
write8(GYRO_REGISTER_CTRL_REG1, 0x00);
write8(GYRO_REGISTER_CTRL_REG1, 0x0F);
write8(GYRO_REGISTER_CTRL_REG4, 0x20);
write8(GYRO_REGISTER_CTRL_REG5, 0x80);
readingValid = false;
// Serial.println("Changing range to 2000DPS");
break;
case GYRO_RANGE_250DPS:
/* Push the range up to 500dps */
_range = GYRO_RANGE_500DPS;
write8(GYRO_REGISTER_CTRL_REG1, 0x00);
write8(GYRO_REGISTER_CTRL_REG1, 0x0F);
write8(GYRO_REGISTER_CTRL_REG4, 0x10);
write8(GYRO_REGISTER_CTRL_REG5, 0x80);
readingValid = false;
// Serial.println("Changing range to 500DPS");
break;
default:
readingValid = true;
break;
}
}
else
{
/* All values are withing range */
readingValid = true;
}
}
}
/* Compensate values depending on the resolution */
switch(_range)
{
case GYRO_RANGE_250DPS:
event->gyro.x *= GYRO_SENSITIVITY_250DPS;
event->gyro.y *= GYRO_SENSITIVITY_250DPS;
event->gyro.z *= GYRO_SENSITIVITY_250DPS;
break;
case GYRO_RANGE_500DPS:
event->gyro.x *= GYRO_SENSITIVITY_500DPS;
event->gyro.y *= GYRO_SENSITIVITY_500DPS;
event->gyro.z *= GYRO_SENSITIVITY_500DPS;
break;
case GYRO_RANGE_2000DPS:
event->gyro.x *= GYRO_SENSITIVITY_2000DPS;
event->gyro.y *= GYRO_SENSITIVITY_2000DPS;
event->gyro.z *= GYRO_SENSITIVITY_2000DPS;
break;
}
/* Convert values to rad/s */
event->gyro.x *= SENSORS_DPS_TO_RADS;
event->gyro.y *= SENSORS_DPS_TO_RADS;
event->gyro.z *= SENSORS_DPS_TO_RADS;
}
/**************************************************************************/
/*!
@brief Gets the sensor_t data
*/
/**************************************************************************/
void Adafruit_L3GD20_Unified::getSensor(sensor_t* sensor)
{
/* Clear the sensor_t object */
memset(sensor, 0, sizeof(sensor_t));
/* Insert the sensor name in the fixed length char array */
strncpy (sensor->name, "L3GD20", sizeof(sensor->name) - 1);
sensor->name[sizeof(sensor->name)- 1] = 0;
sensor->version = 1;
sensor->sensor_id = _sensorID;
sensor->type = SENSOR_TYPE_GYROSCOPE;
sensor->min_delay = 0;
sensor->max_value = (float)this->_range * SENSORS_DPS_TO_RADS;
sensor->min_value = (this->_range * -1.0) * SENSORS_DPS_TO_RADS;
sensor->resolution = 0.0F; // TBD
}