draft-aboba-emu-rfc5216bis-00.txt

EMU Working Group                                          Bernard Aboba
Internet-Draft                                     Microsoft Corporation
Obsoletes: 5216                                               Ryan Hurst
Category: Full Standard                                           Google
Expires: July 1, 2018                                         Alan DeKok
                                                      FreeRADIUS Project



                  The EAP TLS Authentication Protocol
                   draft-aboba-emu-rfc5216bis-01.txt

Abstract

   The Extensible Authentication Protocol (EAP), defined in RFC 3748,
   provides support for multiple authentication methods.  Transport
   Level Security (TLS) provides for mutual authentication, integrity-
   protected ciphersuite negotiation and key exchange between two
   endpoints.  This document defines EAP-TLS, which includes support for
   certificate-based mutual authentication and key derivation.

   This document obsoletes RFC 5216. A summary of the changes between
   this document and RFC 5216 is available in Appendix A.

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

   This Internet-Draft will expire on July 1, 2018.

Copyright Notice

   Copyright (c) 2017 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents



Aboba, Hurst & DeKok          Full Standard                     [Page 1]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   (https://trustee.ietf.org/license-info) in effect on the date of
   publication of this document.  Please review these documents
   carefully, as they describe your rights and restrictions with respect
   to this document.  Code Components extracted from this document must
   include Simplified BSD License text as described in Section 4.e of
   the Trust Legal Provisions and are provided without warranty as
   described in the Simplified BSD License.

   This document may contain material from IETF Documents or IETF
   Contributions published or made publicly available before November
   10, 2008.  The person(s) controlling the copyright in some of this
   material may not have granted the IETF Trust the right to allow
   modifications of such material outside the IETF Standards Process.
   Without obtaining an adequate license from the person(s) controlling
   the copyright in such materials, this document may not be modified
   outside the IETF Standards Process, and derivative works of it may
   not be created outside the IETF Standards Process, except to format
   it for publication as an RFC or to translate it into languages other
   than English.

Table of Contents

1.  Introduction..............................................    3
      1.1    Requirements Language ...........................    3
      1.2    Terminology .....................................    3
2.  Protocol Overview ........................................    4
      2.1    Overview of the EAP-TLS Conversation ............    4
      2.2    Identity Verification ...........................   15
      2.3    Key Hierarchy ...................................   16
      2.4    Ciphersuite and Compression Negotiation .........   18
3.  Detailed Description of the EAP-TLS Protocol .............   19
      3.1     EAP TLS Request Packet .........................   19
      3.2     EAP TLS Response Packet ........................   21
4.  IANA Considerations ......................................   22
5.  Security Considerations ..................................   22
      5.1     Security Claims ................................   22
      5.2     Peer and Server Identities .....................   23
      5.3     Certificate Validation .........................   24
      5.4     Certificate Revocation .........................   25
      5.5     Packet Modification Attacks ....................   26
6.  References ...............................................   27
      6.1    Normative references ....... ....................   27
      6.2    Informative references ..........................   28
Acknowledgments ..............................................   29
Authors' Addresses ...........................................   30
Appendix A - Changes from RFC 2716 ...........................   31
Full Copyright Statement .....................................   32
Intellectual Property ........................................   32



Aboba, Hurst & DeKok          Full Standard                     [Page 2]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


1.  Introduction

   The Extensible Authentication Protocol (EAP), described in [RFC3748],
   provides a standard mechanism for support of multiple authentication
   methods.  Through the use of EAP, support for a number of
   authentication schemes may be added, including smart cards, Kerberos,
   Public Key, One Time Passwords, and others.  EAP has been defined for
   use with a variety of lower layers, including Point-to-Point Protocol
   (PPP) [RFC1661], Layer 2 tunneling protocols such as PPTP [RFC2637]
   or L2TP [RFC2661], IEEE 802 wired networks [IEEE-802.1X] and wireless
   technologies such as IEEE 802.11 [IEEE-802.11] and IEEE 802.16
   [IEEE-802.16e].

   While the EAP methods defined in [RFC3748] did not support mutual
   authentication, the use of EAP with wireless technologies such as
   [IEEE-802.11] has resulted in development of a new set of
   requirements.  As described in "EAP Method Requirements for Wireless
   LANs" [RFC4017], it is desirable for EAP methods used for wireless
   LAN authentication to support mutual authentication and key
   derivation.  Other link layers can also make use of EAP to enable
   mutual authentication and key derivation.

   This document defines EAP-Transport Layer Security (EAP-TLS), which
   includes support for certificate-based mutual authentication and key
   derivation, utilizing the version negotiation, protected ciphersuite
   negotiation, mutual authentication and key management capabilities of
   the TLS protocol.  While this document obsoletes RFC 5216 [RFC5216],
   it remains backward compatible with it.  A summary of the changes
   between this document and RFC 5216 is available in Appendix A.

1.1.  Requirements

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in [RFC2119].

1.2.  Terminology

    This document frequently uses the following terms:

authenticator
     The entity initiating EAP authentication.

peer The entity that responds to the authenticator.  In [IEEE-802.1X],
     this entity is known as the Supplicant.

backend authentication server
     A backend authentication server is an entity that provides an



Aboba, Hurst & DeKok          Full Standard                     [Page 3]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


     authentication service to an authenticator.  When used, this server
     typically executes EAP methods for the authenticator.  This
     terminology is also used in [IEEE-802.1X].

EAP server
     The entity that terminates the EAP authentication method with the
     peer.  In the case where no backend authentication server is used,
     the EAP server is part of the authenticator.  In the case where the
     authenticator operates in pass-through mode, the EAP server is
     located on the backend authentication server.

Master Session Key (MSK)
     Keying material that is derived between the EAP peer and server and
     exported by the EAP method.

Extended Master Session Key (EMSK)
     Additional keying material derived between the EAP peer and server
     that is exported by the EAP method.

2.  Protocol Overview

2.1.  Overview of the EAP-TLS Conversation

   As described in [RFC3748], the EAP-TLS conversation will typically
   begin with the authenticator and the peer negotiating EAP.  The
   authenticator will then typically send an EAP-Request/Identity packet
   to the peer, and the peer will respond with an EAP-Response/Identity
   packet to the authenticator, containing the peer's user-Id.

   From this point forward, while nominally the EAP conversation occurs
   between the EAP authenticator and the peer, the authenticator can act
   as a pass-through device, with the EAP packets received from the peer
   being encapsulated for transmission to a backend authentication
   server.  In the discussion that follows, we will use the term "EAP
   server" to denote the ultimate endpoint conversing with the peer.

2.1.1.  Base Case
   Once having received the peer's Identity, the EAP server MUST respond
   with an EAP-TLS/Start packet, which is an EAP-Request packet with
   EAP-Type=EAP-TLS, the Start (S) bit set, and no data.  The EAP-TLS
   conversation will then begin, with the peer sending an EAP-Response
   packet with EAP-Type=EAP-TLS.  The data field of that packet will
   encapsulate one or more TLS records in TLS record layer format,
   containing a TLS client_hello handshake message.  The current cipher
   spec for the TLS records will be TLS_NULL_WITH_NULL_NULL and null
   compression.  This current cipher spec remains the same until the
   change_cipher_spec message signals that subsequent records will have
   the negotiated attributes for the remainder of the handshake.



Aboba, Hurst & DeKok          Full Standard                     [Page 4]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   The client_hello message contains the peer's TLS version number, a
   sessionId, a random number, and a set of ciphersuites supported by
   the peer.  The version offered by the peer MUST correspond to TLS
   v1.0 or later.

   The EAP server will then respond with an EAP-Request packet with EAP-
   Type=EAP-TLS.  The data field of this packet will encapsulate one or
   more TLS records.  These will contain a TLS server_hello handshake
   message, possibly followed by TLS certificate, server_key_exchange,
   certificate_request, server_hello_done and/or finished handshake
   messages, and/or a TLS change_cipher_spec message.  The server_hello
   handshake message contains a TLS version number, another random
   number, a sessionId, and a ciphersuite.  The version offered by the
   server MUST correspond to TLS v1.0 or later.

   If the peer's sessionId is null or unrecognized by the server, the
   server MUST choose the sessionId to establish a new session.
   Otherwise, the sessionId will match that offered by the peer,
   indicating a resumption of the previously established session with
   that sessionId.  The server will also choose a ciphersuite from those
   offered by the peer.  If the session matches the peer's, then the
   ciphersuite MUST match the one negotiated during the handshake
   protocol execution that established the session.

   If the EAP server is not resuming a previously established session,
   then it MUST include a TLS server_certificate handshake message, and
   a server_hello_done handshake message MUST be the last handshake
   message encapsulated in this EAP-Request packet.

   The certificate message contains a public key certificate chain for
   either a key exchange public key (such as an RSA or Diffie-Hellman
   key exchange public key) or a signature public key (such as an RSA or
   Digital Signature Standard (DSS) signature public key).  In the
   latter case, a TLS server_key_exchange handshake message MUST also be
   included to allow the key exchange to take place.

   The certificate_request message is included when the server desires
   the peer to authenticate itself via public key.  While the EAP server
   SHOULD require peer authentication, this is not mandatory, since
   there are circumstances in which peer authentication will not be
   needed (e.g., emergency services, as described in [UNAUTH]), or where
   the peer will authenticate via some other means.

   If the peer supports EAP-TLS and is configured to use it, it MUST
   respond to the EAP-Request with an EAP-Response packet of EAP-
   Type=EAP-TLS.  If the preceding server_hello message sent by the EAP
   server in the preceding EAP-Request packet did not indicate the
   resumption of a previous session, the data field of this packet MUST



Aboba, Hurst & DeKok          Full Standard                     [Page 5]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   encapsulate one or more TLS records containing a TLS
   client_key_exchange, change_cipher_spec, and finished messages.  If
   the EAP server sent a certificate_request message in the preceding
   EAP-Request packet, then unless the peer is configured for privacy
   (see Section 2.1.4) the peer MUST send, in addition, certificate and
   certificate_verify messages.  The former contains a certificate for
   the peer's signature public key, while the latter contains the peer's
   signed authentication response to the EAP server.  After receiving
   this packet, the EAP server will verify the peer's certificate and
   digital signature, if requested.

   If the preceding server_hello message sent by the EAP server in the
   preceding EAP-Request packet indicated the resumption of a previous
   session, then the peer MUST send only the change_cipher_spec and
   finished handshake messages.  The finished message contains the
   peer's authentication response to the EAP server.

   In the case where the EAP-TLS mutual authentication is successful,
   the conversation will appear as follows:

   Authenticating Peer     Authenticator
   -------------------     -------------
                           <- EAP-Request/
                           Identity
   EAP-Response/
   Identity (MyID) ->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS Start)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS client_hello)->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS server_hello,
                             TLS certificate,
                    [TLS server_key_exchange,]
                     TLS certificate_request,
                        TLS server_hello_done)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS certificate,
    TLS client_key_exchange,
    TLS certificate_verify,
    TLS change_cipher_spec,
    TLS finished) ->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS



Aboba, Hurst & DeKok          Full Standard                     [Page 6]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


                           (TLS change_cipher_spec,
                            TLS finished)
   EAP-Response/
   EAP-Type=EAP-TLS ->
                           <- EAP-Success

2.1.2.  Session Resumption

   The purpose of the sessionId within the TLS protocol is to allow for
   improved efficiency in the case where a peer repeatedly attempts to
   authenticate to an EAP server within a short period of time.  While
   this model was developed for use with HTTP authentication, it also
   can be used to provide "fast reconnect" functionality as defined in
   [RFC3748] Section 7.2.1.

   It is left up to the peer whether to attempt to continue a previous
   session, thus shortening the TLS conversation.  Typically the peer's
   decision will be made based on the time elapsed since the previous
   authentication attempt to that EAP server.  Based on the sessionId
   chosen by the peer, and the time elapsed since the previous
   authentication, the EAP server will decide whether to allow the
   continuation, or whether to choose a new session.

   In the case where the EAP server and authenticator reside on the same
   device, the peer will only be able to continue sessions when
   connecting to the same authenticator.  Should the authenticators be
   set up in a rotary or round-robin then it may not be possible for the
   peer to know in advance the authenticator it will be connecting to,
   and therefore which sessionId to attempt to reuse.  As a result, it
   is likely that the continuation attempt will fail.  In the case where
   the EAP authentication is remoted then continuation is much more
   likely to be successful, since multiple authenticators will utilize
   the same backend authentication server.

   If the EAP server is resuming a previously established session, then
   it MUST include only a TLS change_cipher_spec message and a TLS
   finished handshake message after the server_hello message.  The
   finished message contains the EAP server's authentication response to
   the peer.

   In the case where a previously established session is being resumed,
   and both sides authenticate successfully, the conversation will
   appear as follows:

   Authenticating Peer     Authenticator
   -------------------     -------------
                           <- EAP-Request/
                           Identity



Aboba, Hurst & DeKok          Full Standard                     [Page 7]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   EAP-Response/
   Identity (MyID) ->
                           <- EAP-Request/
                           EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS Start)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS client_hello)->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS server_hello,
                           TLS change_cipher_spec
                           TLS finished)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS change_cipher_spec,
    TLS finished) ->
                           <- EAP-Success

2.1.3.  Termination

   To ensure that the peer receives the TLS alert message, the EAP
   server MUST wait for the peer to reply with an EAP-Response packet.
   The EAP-Response packet sent by the peer MAY encapsulate a TLS
   client_hello handshake message, in which case the EAP server MAY
   allow the EAP-TLS conversation to be restarted, or it MAY contain an
   EAP-Response packet with EAP-Type=EAP-TLS and no data, in which case
   the EAP-Server MUST send an EAP-Failure packet, and terminate the
   conversation. It is up to the EAP server whether to allow restarts,
   and if so, how many times the conversation can be restarted.  An EAP
   Server implementing restart capability SHOULD impose a per-peer limit
   on the number of restarts, so as to protect against denial of service
   attacks.

   If the peer authenticates successfully, the EAP server MUST respond
   with an EAP-Request packet with EAP-Type=EAP-TLS, which includes, in
   the case of a new TLS session, one or more TLS records containing TLS
   change_cipher_spec and finished handshake messages.  The latter
   contains the EAP server's authentication response to the peer.  The
   peer will then verify the finished message in order to authenticate
   the EAP server.

   If EAP server authentication is unsuccessful, the peer SHOULD delete
   the session from its cache, preventing reuse of the sessionId. The
   peer MAY send an EAP-Response packet of EAP-Type=EAP-TLS containing a
   TLS Alert message identifying the reason for the failed
   authentication.  The peer MAY send a TLS alert message rather than



Aboba, Hurst & DeKok          Full Standard                     [Page 8]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   immediately terminating the conversation so as to allow the EAP
   server to log the cause of the error for examination by the system
   administrator.

   To ensure that the EAP Server receives the TLS alert message, the
   peer MUST wait for the EAP-Server to reply before terminating the
   conversation.  The EAP Server MUST reply with an EAP-Failure packet
   since server authentication failure is a terminal condition.

   If the EAP server authenticates successfully, the peer MUST send an
   EAP-Response packet of EAP-Type=EAP-TLS, and no data.  The EAP-Server
   then MUST respond with an EAP-Success message.

   In the case where the server authenticates to the peer successfully,
   but the peer fails to authenticate to the server, the conversation
   will appear as follows:

   Authenticating Peer     Authenticator
   -------------------     -------------
                           <- EAP-Request/
                           Identity
   EAP-Response/
   Identity (MyID) ->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS Start)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS client_hello)->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS server_hello,
                             TLS certificate,
                    [TLS server_key_exchange,]
               TLS certificate_request,
                 TLS server_hello_done)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS certificate,
    TLS client_key_exchange,
    TLS certificate_verify,
    TLS change_cipher_spec,
    TLS finished) ->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS change_cipher_spec,
                           TLS finished)
   EAP-Response/



Aboba, Hurst & DeKok          Full Standard                     [Page 9]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   EAP-Type=EAP-TLS ->
                           <- EAP-Request
                           EAP-Type=EAP-TLS
                           (TLS Alert message)
   EAP-Response/
   EAP-Type=EAP-TLS ->
                           <- EAP-Failure
                           (User Disconnected)

   In the case where server authentication is unsuccessful, the
   conversation will appear as follows:

   Authenticating Peer     Authenticator
   -------------------     -------------
                           <- EAP-Request/
                           Identity
   EAP-Response/
   Identity (MyID) ->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS Start)
   EAP-Response/
   EAP-Type=EAP-TLS
    (TLS client_hello)->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS server_hello,
                            TLS certificate,
                  [TLS server_key_exchange,]
                   TLS certificate_request,
                   TLS server_hello_done)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS Alert message) ->
                           <- EAP-Failure
                           (User Disconnected)

2.1.4.  Privacy

   EAP-TLS peer and server implementations MAY support privacy.
   Disclosure of the username is avoided by utilizing a privacy Network
   Access Identifier (NAI) [RFC7542] in the EAP-Response/Identity, and
   transmitting the peer certificate within a TLS session providing
   confidentiality.

   In order to avoid disclosing the peer username, an EAP-TLS peer
   configured for privacy MUST negotiate a TLS ciphersuite supporting
   confidentiality and MUST provide a client certificate list containing



Aboba, Hurst & DeKok          Full Standard                    [Page 10]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   no entries in response to the initial certificate_request from the
   EAP-TLS server.

   An EAP-TLS server supporting privacy MUST NOT treat a certificate
   list containing no entries as a terminal condition;  instead it MUST
   bring up the TLS session and then send a hello_request.  The
   handshake then proceeds normally; the peer sends a client_hello and
   the server replies with a server_hello, certificate,
   server_key_exchange, certificate_request, server_hello_done, etc.
   For the calculation of exported keying material (see Section 2.3),
   the master_secret derived within the second handshake is used.

   An EAP-TLS peer supporting privacy MUST provide a certificate list
   containing at least one entry in response to the subsequent
   certificate_request sent by the server.  If the EAP-TLS server
   supporting privacy does not receive a client certificate in response
   to the subsequent certificate_request, then it MUST abort the
   session.

   EAP-TLS privacy support is designed to allow EAP-TLS peers that do
   not support privacy to interoperate with EAP-TLS servers supporting
   privacy.  EAP-TLS servers supporting privacy MUST request a client
   certificate, and MUST be able to accept a client certificate offered
   by the EAP-TLS peer, in order to preserve interoperability with EAP-
   TLS peers that do not support privacy.

   However, an EAP-TLS peer configured for privacy typically will not be
   able to successfully authenticate with an EAP-TLS server that does
   not support privacy, since such a server will typically treat the
   refusal to provide a client certificate as a terminal error.  As a
   result, unless authentication failure is considered preferable to
   disclosure of the username, EAP-TLS peers SHOULD only be configured
   for privacy on networks known to support it.

   This is most easily achieved with EAP lower layers that support
   network advertisement, so that the network and appropriate privacy
   configuration can be determined.  In order to determine the privacy
   configuration on link layers (such as IEEE 802 wired networks) which
   do not support network advertisement, it may be desirable to utilize
   information provided in the server certificate (such as the subject
   and subjectAltName fields) or within identity selection hints
   [RFC4284] to determine the appropriate configuration.

   In the case where the peer and server support privacy and mutual
   authentication, the conversation will appear as follows:

   Authenticating Peer     Authenticator
   -------------------     -------------



Aboba, Hurst & DeKok          Full Standard                    [Page 11]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


                           <- EAP-Request/
                           Identity
   EAP-Response/
   Identity (Anonymous NAI) ->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS Start)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS client_hello)->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS server_hello,
                            TLS certificate,
                    [TLS server_key_exchange,]
                     TLS certificate_request,
                        TLS server_hello_done)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS certificate (no cert),
    TLS client_key_exchange,
    TLS change_cipher_spec,
    TLS finished) ->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS change_cipher_spec,
                             finished,
                             hello_request)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS client_hello)->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS server_hello,
                             TLS certificate,
                     TLS server_key_exchange,
                     TLS certificate_request,
                        TLS server_hello_done)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS certificate,
    TLS client_key_exchange,
    TLS certificate_verify,
    TLS change_cipher_spec,
    TLS finished) ->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS change_cipher_spec,



Aboba, Hurst & DeKok          Full Standard                    [Page 12]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


                            TLS finished)
   EAP-Response/
   EAP-Type=EAP-TLS ->
                           <- EAP-Success

2.1.5.  Fragmentation

   A single TLS record may be up to 16384 octets in length, but a TLS
   message may span multiple TLS records, and a TLS certificate message
   may in principle be as long as 16MB.  The group of EAP-TLS messages
   sent in a single round may thus be larger than the MTU size or the
   maximum RADIUS packet size of 4096 octets.  As a result, an EAP-TLS
   implementation MUST provide its own support for fragmentation and
   reassembly.  However, in order to ensure interoperability with
   existing implementations, TLS handshake messages SHOULD NOT be
   fragmented into multiple TLS records if they fit within a single TLS
   record.

   In order to protect against reassembly lockup and denial of service
   attacks, it may be desirable for an implementation to set a maximum
   size for one such group of TLS messages.  Since a single certificate
   is rarely longer than a few thousand octets, and no other field is
   likely to be anywhere near as long, a reasonable choice of maximum
   acceptable message length might be 64 KB.

   Since EAP is a simple ACK-NAK protocol, fragmentation support can be
   added in a simple manner.  In EAP, fragments that are lost or damaged
   in transit will be retransmitted, and since sequencing information is
   provided by the Identifier field in EAP, there is no need for a
   fragment offset field as is provided in IPv4.

   EAP-TLS fragmentation support is provided through addition of a flags
   octet within the EAP-Response and EAP-Request packets, as well as a
   TLS Message Length field of four octets. Flags include the Length
   included (L), More fragments (M), and EAP-TLS Start (S) bits.  The L
   flag is set to indicate the presence of the four octet TLS Message
   Length field, and MUST be set for the first fragment of a fragmented
   TLS message or set of messages. The M flag is set on all but the last
   fragment.  The S flag is set only within the EAP-TLS start message
   sent from the EAP server to the peer. The TLS Message Length field is
   four octets, and provides the total length of the TLS message or set
   of messages that is being fragmented; this simplifies buffer
   allocation.

   When an EAP-TLS peer receives an EAP-Request packet with the M bit
   set, it MUST respond with an EAP-Response with EAP-Type=EAP-TLS and
   no data.  This serves as a fragment ACK.  The EAP server MUST wait
   until it receives the EAP-Response before sending another fragment.



Aboba, Hurst & DeKok          Full Standard                    [Page 13]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   In order to prevent errors in processing of fragments, the EAP server
   MUST increment the Identifier field for each fragment contained
   within an EAP-Request, and the peer MUST include this Identifier
   value in the fragment ACK contained within the EAP-Response.
   Retransmitted fragments will contain the same Identifier value.

   Similarly, when the EAP server receives an EAP-Response with the M
   bit set, it MUST respond with an EAP-Request with EAP-Type=EAP-TLS
   and no data.  This serves as a fragment ACK. The EAP peer MUST wait
   until it receives the EAP-Request before sending another fragment.
   In order to prevent errors in the processing of fragments, the EAP
   server MUST increment the Identifier value for each fragment ACK
   contained within an EAP-Request, and the peer MUST include this
   Identifier value in the subsequent fragment contained within an EAP-
   Response.

   In the case where the EAP-TLS mutual authentication is successful,
   and fragmentation is required, the conversation will appear as
   follows:

   Authenticating Peer     Authenticator
   -------------------     -------------
                           <- EAP-Request/
                           Identity
   EAP-Response/
   Identity (MyID) ->
                           <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS Start, S bit set)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS client_hello)->
                           <- EAP-Request/
                              EAP-Type=EAP-TLS
                             (TLS server_hello,
                               TLS certificate,
                     [TLS server_key_exchange,]
                       TLS certificate_request,
                         TLS server_hello_done)
                    (Fragment 1: L, M bits set)
   EAP-Response/
   EAP-Type=EAP-TLS ->
                           <- EAP-Request/
                              EAP-Type=EAP-TLS
                           (Fragment 2: M bit set)
   EAP-Response/
   EAP-Type=EAP-TLS ->
                           <- EAP-Request/



Aboba, Hurst & DeKok          Full Standard                    [Page 14]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


                           EAP-Type=EAP-TLS
                           (Fragment 3)
   EAP-Response/
   EAP-Type=EAP-TLS
   (TLS certificate,
    TLS client_key_exchange,
    TLS certificate_verify,
    TLS change_cipher_spec,
    TLS finished)(Fragment 1:
    L, M bits set)->
                            <- EAP-Request/
                           EAP-Type=EAP-TLS
   EAP-Response/
   EAP-Type=EAP-TLS
   (Fragment 2)->
                          <- EAP-Request/
                           EAP-Type=EAP-TLS
                           (TLS change_cipher_spec,
                            TLS finished)
   EAP-Response/
   EAP-Type=EAP-TLS ->
                           <- EAP-Success

2.2.  Identity Verification

   As noted in [RFC3748] Section 5.1:

      It is RECOMMENDED that the Identity Response be used primarily for
      routing purposes and selecting which EAP method to use.  EAP
      Methods SHOULD include a method-specific mechanism for obtaining
      the identity, so that they do not have to rely on the Identity
      Response.

   As part of the TLS negotiation, the server presents a certificate to
   the peer, and if mutual authentication is requested, the peer
   presents a certificate to the server. EAP-TLS therefore provides a
   mechanism for determining both the peer identity (Peer-Id in
   [RFC5247]) and server identity (Server-Id in [RFC5247]).  For
   details, see Section 5.2.

   Since the identity presented in the EAP-Response/Identity need not be
   related to the identity presented in the peer certificate, EAP-TLS
   implementations SHOULD NOT require that they be identical.  However,
   if they are not identical, the identity presented in the EAP-
   Response/Identity is unauthenticated information, and SHOULD NOT be
   used for access control or accounting purposes.





Aboba, Hurst & DeKok          Full Standard                    [Page 15]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


2.3.  Key Hierarchy

   Figure 1 illustrates the TLS Key Hierarchy, described in [RFC4346]
   Section 6.3.  The derivation proceeds as follows:

   master_secret = TLS-PRF-48(pre_master_secret, "master secret",
                    client.random || server.random)
   key_block     = TLS-PRF-X(master_secret, "key expansion",
                    server.random || client.random)

   Where:

   TLS-PRF-X =     TLS pseudo-random function defined in [RFC4346],
                   computed to X octets.

   In EAP-TLS, the MSK, EMSK and IV are derived from the TLS master
   secret via a one-way function.  This ensures that the TLS master
   secret cannot be derived from the MSK, EMSK or IV unless the one-way
   function (TLS PRF) is broken.  Since the MSK and EMSK are derived
   from the TLS master secret, if the TLS master secret is compromised
   then the MSK and EMSK are also compromised.

   The MSK is divided into two halves, corresponding to the "Peer to
   Authenticator Encryption Key" (Enc-RECV-Key, 32 octets) and
   "Authenticator to Peer Encryption Key" (Enc-SEND-Key, 32 octets).

   The IV is a 64 octet quantity that is a known value; octets 0-31 are
   known as the "Peer to Authenticator IV" or RECV-IV, and Octets 32-63
   are known as the "Authenticator to Peer IV", or SEND-IV.






















Aboba, Hurst & DeKok          Full Standard                    [Page 16]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


         |                       | pre_master_secret       |
   server|                       |                         | client
   Random|                       V                         | Random
         |     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+     |
         |     |                                     |     |
         +---->|             master_secret           |<----+
         |     |                                     |     |
         |     |                                     |     |
         |     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+     |
         |                       |                         |
         V                       V                         V
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                         |
   |                      key_block                          |
   |               label == "key expansion"                  |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |         |         |         |         |         |
     | client  | server  | client  | server  | client  | server
     | MAC     | MAC     | write   | write   | IV      | IV
     |         |         |         |         |         |
     V         V         V         V         V         V

      Figure 1 - TLS [RFC4346] Key Hierarchy

   EAP-TLS derives exported keying material and parameters as follows:

   Key_Material = TLS-PRF-128(master_secret, "client EAP encryption",
                     client.random || server.random)
   MSK          = Key_Material(0,63)
   EMSK         = Key_Material(64,127)
   IV           = TLS-PRF-64("", "client EAP encryption",
                     client.random || server.random)

   Enc-RECV-Key = MSK(0,31) = Peer to Authenticator Encryption Key
                  (MS-MPPE-Recv-Key in [RFC2548]).  Also known as the
                  PMK in [IEEE-802.11].
   Enc-SEND-Key = MSK(32,63) = Authenticator to Peer Encryption Key
                  (MS-MPPE-Send-Key in [RFC2548])
   RECV-IV      = IV(0,31) = Peer to Authenticator Initialization Vector
   SEND-IV      = IV(32,63) = Authenticator to Peer Initialization
                              Vector
   Session-Id   = 0x0D || client.random || server.random

   Where:

   Key_Material(W,Z) = Octets W through Z inclusive of the key material.
   IV(W,Z)           = Octets W through Z inclusive of the IV.
   MSK(W,Z)          = Octets W through Z inclusive of the MSK.



Aboba, Hurst & DeKok          Full Standard                    [Page 17]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   EMSK(W,Z)         = Octets W through Z inclusive of the EMSK.
   TMS               = TLS master_secret
   TLS-PRF-X         = TLS PRF function computed to X octets
   client.random     = Nonce generated by the TLS client.
   server.random     = Nonce generated by the TLS server.

         |                       | pre_master_secret       |
   server|                       |                         | client
   Random|                       V                         | Random
         |     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+     |
         |     |                                     |     |
         +---->|             master_secret           |<----+
         |     |                                     |     |
         |     |                                     |     |
         |     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+     |
         |                       |                         |
         V                       V                         V
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |                                                         |
   |                        MSK, EMSK                        |
   |               label == "client EAP encryption"          |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |             |             |
     | MSK(0,31)   | MSK(32,63)  | EMSK(0,63)
     |             |             |
     |             |             |
     V             V             V

      Figure 2 - EAP-TLS Key Hierarchy

   The use of these keys is specific to the lower layer, as described in
   [RFC5247] Section 2.1.

2.4.  Version, Ciphersuite and Compression Negotiation

   Since EAP-TLS represents the encapsulation of TLS within EAP,
   implementations utilize TLS to negotiate protocol versions and
   ciphersuites.

   To ensure backward compatibility, EAP-TLS implementations MUST
   support TLS 1.0.  To ensure forward compatibility, EAP-TLS
   implementations MUST support TLS version negotiation.

   EAP-TLS implementations inherit the normative requirements of each
   TLS version they support.  For each version of TLS they support, EAP-
   TLS implementations MUST support the mandatory ciphersuites, SHOULD
   support the recommended ciphersuites and MAY support the optional
   ciphersuites.



Aboba, Hurst & DeKok          Full Standard                    [Page 18]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   However, administrators MAY impose TLS version and ciphersuite
   requirements on EAP clients and servers under their control. For
   example, an administrator can configure EAP-TLS servers within their
   organization to only negotiate TLS versions and ciphersuites
   conforming to organizational policy.

   Since TLS supports ciphersuite negotiation, peers completing the TLS
   negotiation will also have selected a ciphersuite, which includes
   encryption and hashing methods.  Since the ciphersuite negotiated
   within EAP-TLS applies only to the EAP conversation, TLS ciphersuite
   negotiation MUST NOT be used to negotiate the ciphersuites used to
   secure data.

   TLS also supports compression as well as ciphersuite negotiation.
   However, during the EAP-TLS conversation the EAP peer and server MUST
   NOT request or negotiate compression.

3.  Detailed description of the EAP-TLS protocol

3.1.  EAP TLS Request Packet

   A summary of the EAP TLS Request packet format is shown below.  The
   fields are transmitted from left to right.

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Code      |   Identifier  |            Length             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |     Flags     |      TLS Message Length...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
         TLS Message Length        |       TLS Data...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Code

      1

   Identifier

      The Identifier field is one octet and aids in matching responses
      with requests.  The Identifier field MUST be changed on each
      Request packet.

   Length

      The Length field is two octets and indicates the length of the EAP
      packet including the Code, Identifier, Length, Type, and Data



Aboba, Hurst & DeKok          Full Standard                    [Page 19]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


      fields.  Octets outside the range of the Length field should be
      treated as Data Link Layer padding and MUST be ignored on
      reception.

   Type

      13 - EAP TLS

   Flags

      0 1 2 3 4 5 6 7 8
      +-+-+-+-+-+-+-+-+
      |L M S R R R R R|
      +-+-+-+-+-+-+-+-+

      L = Length included
      M = More fragments
      S = EAP-TLS start
      R = Reserved

      The L bit (length included) is set to indicate the presence of the
      four octet TLS Message Length field, and MUST be set for the first
      fragment of a fragmented TLS message or set of messages.  The M
      bit (more fragments) is set on all but the last fragment.  The S
      bit (EAP-TLS start) is set in an EAP-TLS Start message. This
      differentiates the EAP-TLS Start message from a fragment
      acknowledgment.  Implementations of this specification MUST set
      the reserved bits to zero, and MUST ignore them on reception.

   TLS Message Length

      The TLS Message Length field is four octets, and is present only
      if the L bit is set.  This field provides the total length of the
      TLS message or set of messages that is being fragmented.

   TLS data

      The TLS data consists of the encapsulated TLS packet in TLS record
      format.

3.2.  EAP TLS Response Packet

   A summary of the EAP TLS Response packet format is shown below.  The
   fields are transmitted from left to right.

   0                   1                   2                   3
   0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+



Aboba, Hurst & DeKok          Full Standard                    [Page 20]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   |     Code      |   Identifier  |            Length             |
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
   |     Type      |     Flags     |      TLS Message Length...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
         TLS Message Length        |       TLS Data...
   +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   Code

      2

   Identifier

      The Identifier field is one octet and MUST match the Identifier
      field from the corresponding request.

   Length

      The Length field is two octets and indicates the length of the EAP
      packet including the Code, Identifier, Length, Type, and Data
      fields.  Octets outside the range of the Length field should be
      treated as Data Link Layer padding and MUST be ignored on
      reception.

   Type

      13 - EAP TLS

   Flags

      0 1 2 3 4 5 6 7 8
      +-+-+-+-+-+-+-+-+
      |L M R R R R R R|
      +-+-+-+-+-+-+-+-+

      L = Length included
      M = More fragments
      R = Reserved

      The L bit (length included) is set to indicate the presence of the
      four octet TLS Message Length field, and MUST be set for the first
      fragment of a fragmented TLS message or set of messages.  The M
      bit (more fragments) is set on all but the last fragment.
      Implementations of this specification MUST set the reserved bits
      to zero, and MUST ignore them on reception.

   TLS Message Length




Aboba, Hurst & DeKok          Full Standard                    [Page 21]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


      The TLS Message Length field is four octets, and is present only
      if the L bit is set.  This field provides the total length of the
      TLS message or set of messages that is being fragmented.

   TLS data

      The TLS data consists of the encapsulated TLS packet in TLS record
      format.

4.  IANA Considerations

   IANA has allocated EAP Type 13 for EAP-TLS.  The allocation should be
   updated to reference this document.  There are no other IANA actions.

5.  Security Considerations

5.1.  Security Claims

   EAP security claims are defined in [RFC3748] Section 7.2.1.  The
   security claims for EAP-TLS are as follows:

   Auth. mechanism:           Certificates
   Ciphersuite negotiation:   Yes [4]
   Mutual authentication:     Yes [1]
   Integrity protection:      Yes [1]
   Replay protection:         Yes [1]
   Confidentiality:           Yes [2]
   Key derivation:            Yes
   Key strength:              [3]
   Dictionary attack prot.:   Yes
   Fast reconnect:            Yes
   Crypt. binding:            N/A
   Session independence:      Yes [1]
   Fragmentation:             Yes
   Channel binding:           No

   Notes
   -----

   [1] A formal proof of the security of EAP-TLS when used with
   [IEEE-802.11] is provided in [He].  This proof relies on the
   assumption that the private key pairs used by the EAP peer and server
   are not shared with other parties or applications.  For example, a
   backend authentication server supporting EAP-TLS SHOULD NOT utilize
   the same certificate with https.

   [2] Privacy is an optional feature described in Section 2.1.4.




Aboba, Hurst & DeKok          Full Standard                    [Page 22]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   [3] BCP 86 [RFC3766] Section 5 offers advice on the required RSA or
   DH module and DSA subgroup size in bits, for a given level of attack
   resistance in bits.  For example, a 2048-bit RSA key is recommended
   to provide 128-bit equivalent key strength.  The National Institute
   for Standards and Technology (NIST) also offers advice on appropriate
   key sizes in [SP800-57].

   [4] EAP-TLS inherits the secure ciphersuite negotiation features of
   TLS, including key derivation function negotiation (for versions of
   TLS where this is supported).

5.2.  Peer and Server Identities

   The EAP-TLS peer name (Peer-Id) represents the identity to be used
   for access control and accounting purposes.  The Server-Id represents
   the identity of the EAP server.  Together the Peer-Id and Server-Id
   name the entities involved in deriving the MSK/EMSK.

   In EAP-TLS, the Peer-Id and Server-Id are determined from the subject
   or subjectAltName fields in the peer and server certificates.  For
   details, see [RFC3280] Section 4.1.2.6.  Where the subjectAltName
   field is present in the peer or server certificate, the Peer-Id or
   Server-Id MUST be set to the contents of the subjectAltName.  If
   subject naming information is present only in the subjectAltName
   extension of a peer or server certificate, then the subject field
   MUST be an empty sequence and the subjectAltName extension MUST be
   critical.

   Where the peer identity represents a host, a subjectAltName of type
   dnsName SHOULD be present in the peer certificate.  Where the peer
   identity represents a user and not a resource, a subjectAltName of
   type rfc822Name SHOULD be used, conforming to the grammar for the
   Network Access Identifier (NAI) defined in [RFC7542].  If a dnsName
   or rfc822Name are not available other field types (for example a
   subjectAltName of type ipAddress or uniformResourceIdentifier) MAY be
   used.

   A server identity will typically represent a host, not a user or a
   resource.  As a result, a subjectAltName of type dnsName SHOULD be
   present in the server certificate.  If a dnsName is not available
   other field types (for example a subjectAltName of type ipAddress or
   uniformResourceIdentifier) MAY be used.

   Conforming implementations generating new certificates with Network
   Access Identifiers (NAIs) MUST use the rfc822Name in the subject
   alternative name field to describe such identities.  The use of the
   subject name field to contain an emailAddress Relative Distinguished
   Name (RDN) is deprecated, and MUST NOT be used.  The subject name



Aboba, Hurst & DeKok          Full Standard                    [Page 23]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   field MAY contain other RDNs for representing the subject's identity.

   Where it is non-empty, the subject name field MUST contain an X.500
   distinguished name (DN).  If subject naming information is present
   only in the subject name field of a peer certificate and the peer
   identity represents a host or device the subject name field SHOULD
   contain a CommonName (CN) RDN or serialNumber RDN.  If subject naming
   information is present only in the subject name field of a server
   certificate, then the subject name field SHOULD contain a CN RDN or
   serialNumber RDN.

   It is possible for more than one subjectAltName field to be present
   in a peer or server certificate in addition to an empty or non-empty
   subject distinguished name.  EAP-TLS implementations supporting
   export of the Peer-Id and Server-Id SHOULD export all the
   subjectAltName fields within Peer-Ids or Server-Ids, and SHOULD also
   export a non-empty subject distinguished name field within the Peer-
   Ids or Server-Ids.  All of the exported Peer-Ids and Server-Ids are
   considered valid.

   EAP-TLS implementations supporting export of the Peer-Id and Server-
   Id SHOULD export Peer-Ids and Server-Ids in the same order in which
   they appear within the certificate.  Such canonical ordering would
   aid in comparison operations and would enable using those identifiers
   for key derivation if that is deemed useful.  However, the ordering
   of fields within the certificate SHOULD NOT be used for access
   control.

5.3.  Certificate Validation

   Since the EAP-TLS server is typically connected to the Internet, it
   SHOULD support validating the peer certificate using RFC 3280
   [RFC3280] compliant path validation, including the ability to
   retrieve intermediate certificates that may be necessary to validate
   the peer certificate. For details, see [RFC3280] Section 4.2.2.1.

   Where the EAP-TLS server is unable to retrieve intermediate
   certificates, it either will need to be pre-configured with the
   necessary intermediate certificates to complete path validation or it
   will rely on the EAP-TLS peer to provide this information as part of
   the TLS Handshake (see [RFC4346] section 7.4.6).

   In contrast to the EAP-TLS server, the EAP-TLS peer may not have
   Internet connectivity.  Therefore the EAP-TLS server SHOULD provide
   its entire certificate chain minus the root to facilitate certificate
   validation by the peer.  The EAP-TLS peer SHOULD support validating
   the server certificate using RFC 3280 [RFC3280] compliant path
   validation.



Aboba, Hurst & DeKok          Full Standard                    [Page 24]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   Once a TLS session is established EAP-TLS peer and server
   implementations MUST validate that the identities represented in the
   certificate are appropriate and authorized for use with EAP-TLS.  The
   authorization process makes use of the contents of the certificates
   as well as other contextual information.  While authorization
   requirements will vary from deployment to deployment it is
   RECOMMENDED that implementations be able to authorize based on the
   EAP-TLS Peer-Id and Server-Id determined as described in Section 5.2.

   In the case of the EAP-TLS peer this involves ensuring that the
   certificate presented by the EAP-TLS server was intended to be used
   as a server certificate.  Implementations SHOULD use the Extended Key
   Usage (see [RFC3280] section 4.2.1.13) extension and ensure that at
   least one of the following is true:

   1) The certificate issuer included no Extended Key Usage
      identifiers in the certificate.
   2) The issuer included the anyExtendedKeyUsage identifier
      in the certificate (see [RFC3280] section 4.2.1.13).
   3) The issuer included the id-kp-serverAuth identifier
      in the certificate (See [RFC3280] section 4.2.1.13).

   When performing this comparison implementations MUST follow the
   validation rules specified in [RFC2818] Section 3.1.  In the case of
   the server this involves ensuring the certificate presented by the
   EAP-TLS peer was intended to be used as a client certificate.
   Implementations SHOULD use the Extended Key Usage (see [RFC3280]
   Section 4.2.1.13) extension and ensure that at least one of the
   following is true:

   1) The certificate issuer included no Extended Key Usage
      identifiers in the certificate.
   2) The issuer included the anyExtendedKeyUsage identifier in
      the certificate (see [RFC3280] section 4.2.1.13).
   3) The issuer included the id-kp-clientAuth identifier in
      the certificate (see [RFC3280] section 4.2.1.13).

5.4.  Certificate Revocation

   Certificates are long lived assertions of identity.  Therefore it is
   important for EAP-TLS implementations to be capable of checking
   whether these assertions have been revoked.

   EAP-TLS peer and server implementations MUST support the use of
   Certificate Revocation Lists (CRLs); for details, see [RFC3280]
   section 3.3.  EAP-TLS peer and server implementations SHOULD also
   support the Online Certificate Status Protocol (OCSP), described in
   "X.509 Internet Public Key Infrastructure Online Certificate Status



Aboba, Hurst & DeKok          Full Standard                    [Page 25]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   Protocol - OCSP" [RFC2560].  OCSP messages are typically much smaller
   than CRLs which can shorten connection times especially in bandwidth
   constrained environments.  While EAP-TLS servers are typically
   connected to the Internet during the EAP conversation, an EAP-TLS
   peer may not have Internet connectivity until authentication
   completes.

   In the case where the peer is initiating a voluntary Layer 2 tunnel
   using PPTP [RFC2637] or L2TP [RFC2661], the peer will typically
   already have a PPP interface and Internet connectivity established at
   the time of tunnel initiation.

   However, in the case where the EAP-TLS peer is attempting to obtain
   network access, it will not have network connectivity and is
   therefore not capable of checking for certificate revocation until
   after authentication completes and network connectivity is available.
   For this reason EAP-TLS peers and servers SHOULD implement
   Certificate Status Request messages, as described in "Transport Layer
   Security (TLS) Extensions" [RFC4366] section 3.6.  To enable
   revocation checking in situations where servers do not support
   Certificate Status Request messages and network connectivity is not
   available prior to authentication completion,  peer implementations
   MUST also support checking for certificate revocation after
   authentication completes and network connectivity is available, and
   they SHOULD utilize this capability by default.

5.5.  Packet Modification Attacks

   The integrity protection of EAP-TLS packets does not extend to the
   EAP header fields (Code, Identifier, Length) or the Type or Flags
   fields.  As a result, these fields can be modified by an attacker.

   In most cases modification of the Code or Identifier fields will only
   result in a denial of service attack.  However, an attacker can add
   additional data to an EAP-TLS packet so as to cause it to be longer
   than implied by the Length field.  EAP peers, authenticators or
   servers that do not check for this could be vulnerable to a buffer
   overrun.

   It is also possible for an attacker to modify the Type or Flags
   fields.  By modifying the Type field, an attacker could cause one
   TLS-based EAP method to be negotiated instead of another.  For
   example, the EAP-TLS Type field (13) could be changed to indicate
   another TLS-based EAP method.  Unless the alternative TLS-based EAP
   method utilizes a different key derivation formula, it is possible
   that an EAP method conversation altered by a man-in-the-middle could
   run all the way to completion without detection.  Unless the
   ciphersuite selection policies are identical for all TLS-based EAP



Aboba, Hurst & DeKok          Full Standard                    [Page 26]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


   methods utilizing the same key derivation formula, it may be possible
   for an attacker to mount a successful downgrade attack, causing the
   peer to utilize an inferior ciphersuite or TLS-based EAP method.

6.  References

6.1.  Normative References

[RFC2119]      Bradner, S., "Key words for use in RFCs to Indicate
               Requirement Levels", BCP 14, RFC 2119, March 1997.

[RFC2560]      Myers, M., Ankney, R., Malpani, A., Galperin, S. and C.
               Adams, "X.509 Internet Public Key Infrastructure Online
               Certificate Status Protocol - OCSP", RFC 2560, June 1999.

[RFC2818]      Rescorla, E., "HTTP Over TLS", RFC 2818, May 2000.

[RFC3268]      Chown, P., "Advanced Encryption Standard (AES)
               Ciphersuites for Transport Layer Security (TLS)", RFC
               3268, June 2002.

[RFC3280]      Housley, R., Polk, W., Ford, W. and D. Solo, "Internet
               X.509 Public Key Infrastructure Certificate and
               Certificate Revocation List (CRL) Profile", RFC 3280,
               April 2002.

[RFC3748]      Aboba, B., Blunk, L., Vollbrecht, J., Carlson, J. and H.
               Levkowetz, "Extensible Authentication Protocol (EAP)",
               RFC 3748, June 2004.

[RFC4366]      Blake-Wilson, S., Nystrom, M., Hopwood, D., Mikkelsen, J.
               and T. Wright, "Transport Layer Security (TLS)
               Extensions", RFC 4366, April 2006.

[RFC5246bis]   Rescorla, E.  "The Transport Layer Security (TLS)
               Protocol Version 1.3", draft-ietf-tls-tls13-21.txt,
               Internet draft (work in progress), July 2017.

[RFC5705]      Rescorla, E., "Keying Material Exporters for Transport
               Layer Security (TLS)", RFC 5705, March 2010.

[RFC7542]      DeKok, A., "The Network Access Identifier", RFC 7542, May
               2015.

6.2.  Informative References

[IEEE-802.1X]  Institute of Electrical and Electronics Engineers, "Local
               and Metropolitan Area Networks: Port-Based Network Access



Aboba, Hurst & DeKok          Full Standard                    [Page 27]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


               Control", IEEE Standard 802.1X-2004, December 2004.

[IEEE-802.11]  Information technology - Telecommunications and
               information exchange between systems - Local and
               metropolitan area networks - Specific Requirements Part
               11:  Wireless LAN Medium Access Control (MAC) and
               Physical Layer (PHY) Specifications, IEEE Std.
               802.11-2007, 2007.

[IEEE-802.16e] Institute of Electrical and Electronics Engineers, "IEEE
               Standard for Local and Metropolitan Area Networks: Part
               16: Air Interface for Fixed and Mobile Broadband Wireless
               Access Systems: Amendment for Physical and Medium Access
               Control Layers for Combined Fixed and Mobile Operations
               in Licensed Bands", IEEE 802.16e, August 2005.

[He]           He, C., Sundararajan, M., Datta, A., Derek, A. and J.
               Mitchell, "A Modular Correctness Proof of IEEE 802.11i
               and TLS", CCS '05, November 7-11, 2005, Alexandria,
               Virginia, USA

[RFC1661]      Simpson, W., Editor, "The Point-to-Point Protocol (PPP)",
               STD 51, RFC 1661, July 1994.

[RFC2548]      Zorn, G., "Microsoft Vendor-specific RADIUS Attributes",
               RFC 2548, March 1999.

[RFC2637]      Hamzeh, K., Pall, G., Verthein, W., Taarud, J., Little,
               W., and G. Zorn, "Point-to-Point Tunneling Protocol", RFC
               2637, July 1999.

[RFC2661]      Townsley, W., Valencia, A., Rubens, A., Pall, G., Zorn,
               G., and B. Palter, "Layer Two Tunneling Protocol "L2TP"",
               RFC 2661, August 1999.

[RFC3766]      Orman. H. and P. Hoffman, "Determining Strengths for
               Public Keys Used for Exchanging Symmetric Keys", RFC
               3766, April 2004.

[RFC4017]      Stanley, D., Walker, J. and B. Aboba, "Extensible
               Authentication Protocol (EAP) Method Requirements for
               Wireless LANs", RFC 4017, March 2005.

[RFC4284]      Adrangi, F., Lortz, V., Bari, F. and P. Eronen, "Identity
               Selection Hints for the Extensible Authentication
               Protocol (EAP)", RFC 4284, January 2006.





Aboba, Hurst & DeKok          Full Standard                    [Page 28]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


[RFC5216]      Simon, D., Aboba, B. and R. Hurst, "The EAP-TLS
               Authentication Protocol", RFC 5216, March 2008.

[RFC5247]      Aboba, B., Simon, D. and P. Eronen, "Extensible
               Authentication Protocol (EAP) Key Management Framework",
               RFC 5247, August 2008.

[SP800-57]     National Institute of Standards and Technology,
               "Recommendation for Key Management", Special Publication
               800-57, May 2006.

[UNAUTH]       Schulzrinne. H., McCann, S., Bajko, G. and H. Tschofenig,
               "Extensions to the Emergency Services Architecture for
               dealing with Unauthenticated and Unauthorized Devices",
               Internet draft (work in progress), draft-schulzrinne-
               ecrit-unauthenticated-access-01.txt, November 2007.

Acknowledgments

   Thanks to Terence Spies, Mudit Goel, Anthony Leibovitz and Narendra
   Gidwani of Microsoft, Glen Zorn of NetCube, Joe Salowey of Cisco and
   Pasi Eronen of Nokia for useful discussions of this problem space.

Authors' Addresses

   Bernard Aboba
   Microsoft Corporation
   One Microsoft Way
   Redmond, WA 98052-6399

   Phone: +1 425 706 6605
   Fax:   +1 425 936 7329
   EMail: bernard.aboba@gmail.com

   Ryan Hurst
   Google
   EMail: rmh@google.com

   Alan DeKok
   The FreeRADIUS Server Project
   EMail: aland@freeradius.org










Aboba, Hurst & DeKok          Full Standard                    [Page 29]

INTERNET-DRAFT      EAP TLS Authentication Protocol     26 November 2017


Appendix A - Changes from RFC 5216

   This Appendix lists the major changes between [RFC5216] and this
   document.  Minor changes, including style, grammar, spelling, and
   editorial changes are not mentioned here.

   o The document now cites TLS v1.3 as a normative reference (Sections
   1, 6.1).

   o The EAP-TLS key hierarchy is defined using the TLS key extractor
   from [RFC5705].

   o Mandatory, recommended and optional TLS ciphersuites are inherited
   from the TLS versions that are supported.





































Aboba, Hurst & DeKok          Full Standard                    [Page 30]