Releases · OpenIPC/sbc-groundstations

10 Dec 11:26

JohnDGodwin

Orange-Pi-Latest

75bb7dd

Orange Pi 3b + 5(plus) w/ OpenIPC Latest

Latest

These are pre-build images for the Orange Pi 3b, Orange Pi 5, and Orange Pi 5 Plus to stream OpenIPC video.

Release Notes:

Brings support for rtl8812eu, rtl8812bu, rtl8731bu, rtl8733bu, and AR9271 wi-fi cards
DVR functionality has changed. Starting/Stopping recording no longer disrupts the stream.
No need to run the resizefs.sh script anymore.
Multiple receiver wi-fi card support with hot-plugging - You can now use 2 or more wi-fi cards on your groundstation with no hastle. Your wi-fi cards will be autodetected and used by wfb-ng on plug-in.
Contains a full Gstreamer back-end for advanced users.
default gs.key and drone.key files are now included

These images uses the PixelPilot project rather than pure gstreamer to display the video.

On first boot, the stream will not start to give the user the ability to set up the system. Please perform the following steps.

Step 1 - Flash the image to either your onboard emmc or a micro SD card.
Step 2 - Connect a screen and a wired keyboard to your Orange Pi and boot the system.
Step 3 - The system should boot to a CLI. Login as either orangepi/orangepi or root/root (I personally use the orangepi user but some prefer using the root account. EVERYTHING IS LOCATED AT /config)
Step 4 - no longer needed.
Step 5 - (Orange Pi 3b only) Use the onboard wifi to connect to your home network: (note - if you are running your fpv system on the 5.8ghz channels, it would be ideal to connect the onboard wifi to a 2.4ghz network to avoid any possible interference.)

Method 1: Enter nmtui, go down to Activate a connection and activate one of the detected wifi networks.

Method 2: While in the scripts folder, run the wifi-connect.sh. Run ./wifi-connect.sh YOURWIFISSID YOURWIFIPASSWORD

To check your connection after, run nmcli and your wlan0 connection should be green. Make a note of your ip address. We will need this to ssh into the system later.
Step 6 - Set your desired screen resolution and refresh rate in the screen-mode file. sudo nano /config/scripts/screen-mode and change to your desired specifications. Format is WxH@fps -- Common values would be 1920x1080@60, 1920x1080@120. 1280x720@60, 1280x720@120
For smooth DVR playback, set the dvr-fps with sudo nano /config/scripts/dvr-fps to the fps at which your camera is shooting. e.g. 60, 90, 120
Step 7 (optional) - Set your WFB-ng channel in /etc/wifibroadcast.cfg and transfer your gs.key to /etc (A standard gs.key and drone.key are now provided)
Step 8 - Shutdown the system, disconnect the keyboard, and connect your wifi card. Boot the system and SSH from a separate computer.
Step 9 - Test the system. Run wfb-cli gs and plug in your camera. Make sure you are properly getting video and telemetry packets. Hit CTRL-C to exit the wfb-cli. Run sudo systemctl start openipc.service and the display connected to the OrangePi should change to your video feed. Press your DVR button. The stream should stop (the screen will go black for a second) and a new stream being recorded should start. Press the dvr button again to stop the saving stream and go back to the display stream. (Again, the stream should go black for a second. If it doesn't, press the button again) Confirm there is a .mp4 video file in /media by going to x.x.x.x:8080 in a browser, replacing x.x.x.x with your Orange Pi's ip address. . Run sudo systemctl stop openipc.service to stop testing.
Step 10 - Last and final step. Once you have confirmed the system is working and you have set your desired settings, run sudo systemctl enable openipc.service to have the stream begin on boot.

These images includes DVR functionality; It requires a push button to be installed to the gpio header between a physical GPIO pin and 3.3v like so:

For the Orange Pi 3b:

For the Orange Pi 5 connect to gpio and gnd like so:

For the Orange Pi 5 Plus it is the same as the orange pi 3b:

DVR is saved to the media folder in your root directory. DVR can be accessed either at /media or via a media server. Connect your groundstation to your home network and it can be accessed via a web browser at x.x.x.x:8080 -- replace x.x.x.x with your groundstation's local ip address.

NOTE
The Orange Pi 5 Plus has 2 HDMI-out ports. You MUST use the "middle" HDMI port:

Assets 7

17 Oct 16:21

JohnDGodwin

zero3w-v1.8.3

010dcce

Radxa Zero 3w w/ OpenIPC v1.8.3

This is a prebuilt image for the Radxa Zero 3w to stream OpenIPC video.

V1.8.3 Release Notes:

Brings support for rtl8812bu, rtl8731bu, rtl8733bu, and AR9271 wi-fi cards
A sandbox image is now available for developers. It is identical to the release image but contains 1.5G of extra space for user extras.
DVR functionality has changed. Starting/Stopping recording no longer disrupts the stream.
The DVR recording button GPIO has changed to be compatible with other systems (RubyFPV). Your DVR button should be connected between pin 32 and 3.3v.

This image uses the PixelPilot project rather than pure gstreamer to display the video.

On first boot, the stream will not start to give the user the ability to set up the system. Please perform the following steps.

Step 1 - Flash the image to either your onboard emmc or a micro SD card.
Step 2 - Connect a screen and a wired keyboard to your radxa (you may need a usb-a to usb-c adapter or hub) and boot the system.
Step 3 - The system should boot to a CLI. Login as either radxa/radxa or root/root (I personally use the radxa user but some prefer using the root account. EVERYTHING IS LOCATED AT /config)
Step 4 - no longer needed.
Step 5 - Use the onboard wifi to connect to your home network: (note - if you are running your fpv system on the 5.8ghz channels, it would be ideal to connect the onboard wifi to a 2.4ghz network to avoid any possible interference.)

Method 1: Edit the config.txt file in /config to contain connect_wi-fi YOUR_WIFI_SSID YOUR_WIFI_PASSWORD

Method 2: Enter nmtui, go down to Activate a connection and activate one of the detected wifi networks.

Method 3: While in the scripts folder, run the wifi-connect.sh. Instructions below.

To check your connection after, run nmcli and your wlan0 connection should be green. Make a note of your ip address. We will need this to ssh into the system later.
Step 6 - Set your desired screen resolution and refresh rate in the screen-mode file. sudo nano /config/scripts/screen-mode and change to your desired specifications. Format is WxH@fps -- Common values would be 1920x1080@60, 1920x1080@120. 1280x720@60, 1280x720@120
For smooth DVR playback, set the dvr-fps with sudo nano /config/scripts/dvr-fps to the fps at which your camera is shooting. e.g. 60, 90, 120
Step 7 (optional) - Set your WFB-ng channel in /etc/wifibroadcast.cfg and transfer your gs.key to /etc (A standard gs.key and drone.key are now provided)
Step 8 - Shutdown the system, disconnect the keyboard, and connect your wifi card. Boot the system and SSH from a separate computer.
Step 9 - Test the system. Run wfb-cli gs and plug in your camera. Make sure you are properly getting video and telemetry packets. Hit CTRL-C to exit the wfb-cli. Run sudo systemctl start openipc.service and the display connected to the radxa should change to your video feed. Press your DVR button. The stream should stop (the screen will go black for a second) and a new stream being recorded should start. Press the dvr button again to stop the saving stream and go back to the display stream. (Again, the stream should go black for a second. If it doesn't, press the button again) Confirm there is a .mp4 video file in /media by going to x.x.x.x:8080 in a browser, replacing x.x.x.x with your radxa's ip address. . Run sudo systemctl stop openipc.service to stop testing.
Step 10 - Last and final step. Once you have confirmed the system is working and you have set your desired settings, run sudo systemctl enable openipc.service to have the stream begin on boot.

How to flash the image to your onboard emmc

On first boot, connect a keyboard and login is root/root (user/password is radxa/radxa)

Run wfb_keygen (located in your path) and transfer the keys. Run sudo cp gs.key /etc to transfer your gs.key to the groundstation's /etc directory. To transfer the drone.key file, connect your camera and radxa to your home network, then run scp drone.key [email protected]:/etc and replace x.x.x.x with your camera's local ip address. (You will need to set up your network accordingly.)

Stock settings will set the display to 1920x1080@60fps. You will want to change this behavior in the screen-mode file in the scripts folder found in your home directory. -- sudo nano /config/screen-mode
e.g. for HDZ goggles -- change to 1280x720@100

The recommended way of connecting to your home network with the onboard wifi is to use the nmtui command. Enter nmtui, go down to Activate a connection and activate one of the detected wifi networks.

You can use the handy wifi-connect.sh script found in the scripts folder. Run the script with your home network name and password as follows: ./wifi-connect.sh NetworkName NetworkPassword. Replace NetworkName and NetworkPassword with your home network credentials.

You can also manually setup the onboard wifi for SSH connectivity. (udev rules and networkmanager are already configured in this image, you only need to execute the nmcli commands)

This image includes DVR functionality; It requires a push button to be installed to the gpio header between physical pin 32 and 3.3v like so:

Assets 6

14 Oct 13:17

JohnDGodwin

zero3w-v1.8.2

010dcce

Radxa Zero 3w w/ OpenIPC v1.8.2 Pre-release

Pre-release

V1.8.2 Release Notes:

Adds ath9k_htc driver for Atheros AR9271 support.

Read notes on v1.8.0 for further instructions.

Assets 3

13 Oct 23:26

JohnDGodwin

zero3w-v1.8.1

8a52c7a

Radxa Zero 3w w/ OpenIPC v1.8.1 Pre-release

Pre-release

V1.8.1 Release Notes:

Adds support for rtl8731bu with 8733bu drivers

Read notes on v1.8.0 for further instructions.

Assets 3

09 Oct 01:25

JohnDGodwin

zero3w-v1.8.0

5922895

Radxa Zero 3w w/ OpenIPC v1.8.0

This is a prebuilt image for the Radxa Zero 3w to stream OpenIPC video.

V1.8.0 Release Notes:

Built using rsdk
No need to run the resizefs.sh script anymore.
Uses the most up-to-date PixelPilot.
Contains a full Gstreamer back-end for advanced users.
Everything can be configured from the /config directory that will automount on Windows. Enter your credentials for your home wi-fi for ssh and dvr in the config.txt file, set your screen-mode for your connected hdmi screen, and dvr-fps to the fps your camera is shooting. Boot the image, ssh in, test the system, then enable openipc.service.

This image uses the PixelPilot project rather than pure gstreamer to display the video.

On first boot, the stream will not start to give the user the ability to set up the system. Please perform the following steps.

Step 1 - Flash the image to either your onboard emmc or a micro SD card.
Step 2 - Connect a screen and a wired keyboard to your radxa (you may need a usb-a to usb-c adapter or hub) and boot the system.
Step 3 - The system should boot to a CLI. Login as either radxa/radxa or root/root (I personally use the radxa user but some prefer using the root account. EVERYTHING IS LOCATED AT /config)
Step 4 - no longer needed.
Step 5 - Use the onboard wifi to connect to your home network: (note - if you are running your fpv system on the 5.8ghz channels, it would be ideal to connect the onboard wifi to a 2.4ghz network to avoid any possible interference.)

Method 1: Edit the config.txt file in /config to contain connect_wi-fi YOUR_WIFI_SSID YOUR_WIFI_PASSWORD

Method 2: Enter nmtui, go down to Activate a connection and activate one of the detected wifi networks.

Method 3: While in the scripts folder, run the wifi-connect.sh. Instructions below.

To check your connection after, run nmcli and your wlan0 connection should be green. Make a note of your ip address. We will need this to ssh into the system later.
Step 6 - Set your desired screen resolution and refresh rate in the screen-mode file. sudo nano /config/scripts/screen-mode and change to your desired specifications. Format is WxH@fps -- Common values would be 1920x1080@60, 1920x1080@120. 1280x720@60, 1280x720@120
For smooth DVR playback, set the dvr-fps with sudo nano /config/scripts/dvr-fps to the fps at which your camera is shooting. e.g. 60, 90, 120
Step 7 (optional) - Set your WFB-ng channel in /etc/wifibroadcast.cfg and transfer your gs.key to /etc (A standard gs.key and drone.key are now provided)
Step 8 - Shutdown the system, disconnect the keyboard, and connect your wifi card. Boot the system and SSH from a separate computer.
Step 9 - Test the system. Run wfb-cli gs and plug in your camera. Make sure you are properly getting video and telemetry packets. Hit CTRL-C to exit the wfb-cli. Run sudo systemctl start openipc.service and the display connected to the radxa should change to your video feed. Press your DVR button. The stream should stop (the screen will go black for a second) and a new stream being recorded should start. Press the dvr button again to stop the saving stream and go back to the display stream. (Again, the stream should go black for a second. If it doesn't, press the button again) Confirm there is a .mp4 video file in /media by going to x.x.x.x:8080 in a browser, replacing x.x.x.x with your radxa's ip address. . Run sudo systemctl stop openipc.service to stop testing.
Step 10 - Last and final step. Once you have confirmed the system is working and you have set your desired settings, run sudo systemctl enable openipc.service to have the stream begin on boot.

How to flash the image to your onboard emmc

On first boot, connect a keyboard and login is root/root (user/password is radxa/radxa)

You can also manually setup the onboard wifi for SSH connectivity. (udev rules and networkmanager are already configured in this image, you only need to execute the nmcli commands)

This image includes DVR functionality; It requires a push button to be installed to the gpio header between physical pins 25 and 27 like so:

To record DVR, push the button once. The preview stream will end and the the recording stream will start; DVR will begin recording. When finished, push the button once to stop the recording and save the file. The recording stream will end and the preview stream will return.

Assets 5

07 Oct 08:20

JohnDGodwin

zero3w-v1.8.0-rc1

5922895

Radxa Zero 3w w/ OpenIPC v1.8.0-rc1 Pre-release

Pre-release

This is a prebuilt image for the Radxa Zero 3w to stream OpenIPC video.

V1.8.0 Release Notes:

Built using rsdk
No need to run the resizefs.sh script anymore. Connect to your 2.4Ghz home wi-fi for ssh and dvr, set your screen-mode for your connected hdmi screen and dvr-fps to the fps your camera is shooting, and enable openipc.service.
Uses the most up-to-date PixelPilot.

This image uses the PixelPilot project rather than pure gstreamer to display the video.

On first boot, the stream will not start to give the user the ability to set up the system. Please perform the following steps.

Step 1 - Flash the image to either your onboard emmc or a micro SD card.
Step 2 - Connect a screen and a wired keyboard to your radxa (you may need a usb-a to usb-c adapter or hub) and boot the system.
Step 3 - The system should boot to a CLI. Login as either radxa/radxa or root/root (I personally use the radxa user but some prefer using the root account. EVERYTHING IS LOCATED AT /config)
Step 4 - no longer needed.
Step 5 - Use the onboard wifi to connect to your home network: (note - if you are running your fpv system on the 5.8ghz channels, it would be ideal to connect the onboard wifi to a 2.4ghz network to avoid any possible interference.)

Method 1: Edit the config.txt file to contain connect_wi-fi YOUR_WIFI_SSID YOUR_WIFI_PASSWORD

Method 2: Enter nmtui, go down to Activate a connection and activate one of the detected wifi networks.

Method 3: While in the scripts folder, run the wifi-connect.sh. Instructions below.

To check your connection after, run nmcli and your wlan0 connection should be green. Make a note of your ip address. We will need this to ssh into the system later.
Step 6 - Set your desired screen resolution and refresh rate in the screen-mode file. sudo nano /config/scripts/screen-mode and change to your desired specifications. Format is WxH@fps -- Common values would be 1920x1080@60, 1920x1080@120. 1280x720@60, 1280x720@120
Step 7 (optional) - Set your WFB-ng channel in /etc/wifibroadcast.cfg and transfer your gs.key to /etc (A standard gs.key and drone.key are now provided)
Step 8 - Shutdown the system, disconnect the keyboard, and connect your wifi card. Boot the system and SSH from a separate computer.
Step 9 - Test the system. Run wfb-cli gs and plug in your camera. Make sure you are properly getting video and telemetry packets. Hit CTRL-C to exit the wfb-cli. Run sudo systemctl start openipc.service and the display connected to the radxa should change to your video feed. Press your DVR button. The stream should stop (the screen will go black for a second) and a new stream being recorded should start. Press the dvr button again to stop the saving stream and go back to the display stream. (Again, the stream should go black for a second. If it doesn't, press the button again) Confirm there is a .mp4 video file in /media by going to x.x.x.x:8080 in a browser, replacing x.x.x.x with your radxa's ip address. . Run sudo systemctl stop openipc.service to stop testing.
Step 10 - Last and final step. Once you have confirmed the system is working and you have set your desired settings, run sudo systemctl enable openipc.service to have the stream begin on boot.

How to flash the image to your onboard emmc

On first boot, connect a keyboard and login is root/root (user/password is radxa/radxa)

You can also manually setup the onboard wifi for SSH connectivity. (udev rules and networkmanager are already configured in this image, you only need to execute the nmcli commands)

This image includes DVR functionality; It requires a push button to be installed to the gpio header between physical pins 25 and 27 like so:

Assets 5

28 Sep 12:28

JohnDGodwin

zero3w-v1.7.0

619e7e4

Radxa Zero 3w w/ OpenIPC v1.7.0

This is a prebuilt image for the Radxa Zero 3w to stream OpenIPC video.

V1.7.0 Release Notes:

Locations have changed with this release -- everything is now located on a separate FAT32 partition mounted to /config on boot. This enables the user to make settings changes outside of booting the image. e.g. Plug the SD card into a windows PC and a drive will display named config. Inside is a folder named scripts containing the settings files.
DVR recording location has also changed. It is now saved to /media. It can of course still be accessed via a web browser located at x.x.x.x:8080 -- replace x.x.x.x with your groundstation's local ip address.
This image assumes the user is using MSP OSD and the PixelPilot osd has been disabled by default. While MSP OSD is recommended, the old mavlink osd can be re-enabled by changing the perimeters passed to the launch of PixelPilot in the stream.sh script.

This image uses the PixelPilot project rather than pure gstreamer to display the video.

On first boot, the stream will not start to give the user the ability to set up the system. Please perform the following steps.

Step 1 - Flash the image to either your onboard emmc or a micro SD card.
Step 2 - Connect a screen and a wired keyboard to your radxa (you may need a usb-a to usb-c adapter or hub) and boot the system.
Step 3 - The system should boot to a CLI. Login as either radxa/radxa or root/root (I personally use the radxa user but some prefer using the root account. EVERYTHING IS LOCATED AT /config)
Step 4 - Change to the /config/scripts directory by running cd /config/scripts and run ./resizefs.sh to repartition and resize your filesystem. Ignore the red warning text and let the script finish.
Step 5 - Use the onboard wifi to connect to your home network: (note - if you are running your fpv system on the 5.8ghz channels, it would be ideal to connect the onboard wifi to a 2.4ghz network to avoid any possible interference.)

Method 1: Enter nmtui, go down to Activate a connection and activate one of the detected wifi networks.

Method 2: While in the scripts folder, run the wifi-connect.sh. Instructions below.

To check your connection after, run nmcli and your wlan0 connection should be green. Make a note of your ip address. We will need this to ssh into the system later.
Step 6 - Set your desired screen resolution and refresh rate in the screen-mode file. sudo nano /config/scripts/screen-mode and change to your desired specifications. Format is WxH@fps -- Common values would be 1920x1080@60, 1920x1080@120. 1280x720@60, 1280x720@120
Step 7 (optional) - Set your WFB-ng channel in /etc/wifibroadcast.cfg and transfer your gs.key to /etc (A standard gs.key and drone.key are now provided)
Step 8 - Shutdown the system, disconnect the keyboard, and connect your wifi card. Boot the system and SSH from a separate computer.
Step 9 - Test the system. Run wfb-cli gs and plug in your camera. Make sure you are properly getting video and telemetry packets. Hit CTRL-C to exit the wfb-cli. Run sudo systemctl start openipc.service and the display connected to the radxa should change to your video feed. Press your DVR button. The stream should stop (the screen will go black for a second) and a new stream being recorded should start. Press the dvr button again to stop the saving stream and go back to the display stream. (Again, the stream should go black for a second. If it doesn't, press the button again) Confirm there is a .mp4 video file in /media by going to x.x.x.x:8080 in a browser, replacing x.x.x.x with your radxa's ip address. . Run sudo systemctl stop openipc.service to stop testing.
Step 10 - Last and final step. Once you have confirmed the system is working and you have set your desired settings, run sudo systemctl enable openipc.service to have the stream begin on boot.

How to flash the image to your onboard emmc

On first boot, connect a keyboard and login is root/root (user/password is radxa/radxa)

Run ./resizefs.sh to repartition and resize your filesystem. Ignore all the red text and let the script finish.

You can also manually setup the onboard wifi for SSH connectivity. (udev rules and networkmanager are already configured in this image, you only need to execute the nmcli commands)

This image includes DVR functionality; It requires a push button to be installed to the gpio header between physical pins 25 and 27 like so:

Assets 11

23 Sep 13:26

JohnDGodwin

zero3w-v1.6.0

38899aa

Radxa Zero 3w w/ OpenIPC v1.6.0

V1.6.0 Release Notes:

Multiple receiver wi-fi card support with hot-plugging - You can now use 2 or more wi-fi cards on your groundstation with no hastle. Your wi-fi cards will be autodetected and used by wfb-ng on plug-in.
rtl8812eu support

This image uses the PixelPilot project rather than pure gstreamer to display the video.

On first boot, the stream will not start to give the user the ability to set up the system. Please perform the following steps.

Step 1 - Flash the image to either your onboard emmc or a micro SD card.
Step 2 - Connect a screen and a wired keyboard to your radxa (you may need a usb-a to usb-c adapter or hub) and boot the system.
Step 3 - The system should boot to a CLI. Login as either radxa/radxa or root/root (I personally use the radxa user but some prefer using the root account. EVERYTHING IS LOCATED AT /home/radxa)
Step 4 - Run ./resizefs.sh to repartition and resize your filesystem. Ignore the red warning text and let the script finish.
Step 5 - Use the onboard wifi to connect to your home network:
Method 1: Enter nmtui, go down to Activate a connection and activate one of the detected wifi networks.
Method 2: While in the scripts folder, run the wifi-connect.sh script with your home network name and password as follows: ./wifi-connect.sh NetworkName NetworkPassword. Replace NetworkName and NetworkPassword with your home network credentials.
To check your connection after, run nmcli and your wlan0 connection should be green. Make a note of your ip address. We will need this to ssh into the system later.
Step 6 - Set your desired screen resolution and refresh rate in the screen-mode file. sudo nano /home/radxa/scripts/screen-mode and change to your desired specifications. Format is WxH@fps -- Common values would be 1920x1080@60, 1920x1080@120. 1280x720@60, 1280x720@120
Step 7 - Set your WFB-ng channel in /etc/wifibroadcast.cfg and transfer your gs.key to /etc (A standard gs.key and drone.key are now provided)
Step 8 - Shutdown the system, disconnect the keyboard, and connect your wifi card. Boot the system and SSH from a separate computer.
Step 9 - Test the system. Run wfb-cli gs and plug in your camera. Make sure you are properly getting video and telemetry packets. Hit CTRL-C to exit the wfb-cli. Run sudo systemctl start openipc.service and the display connected to the radxa should change to your video feed with OSD. Press your DVR button. The stream should stop (the screen will go black for a second) and a new stream being recorded should start. Press the dvr button again to stop the saving stream and go back to the display stream. (Again, the stream should go black for a second. If it doesn't, press the button again) Confirm there is a .mp4 video file in home/radxa/Videos by going to x.x.x.x:8080 in a browser, replacing x.x.x.x with your radxa's ip address. . Run sudo systemctl stop openipc.service to stop testing.
Step 10 - Last and final step. Once you have confirmed the system is working and you have set your desired settings, run sudo systemctl enable openipc.service to have the stream begin on boot.

This is a prebuilt image for the Radxa Zero 3w to stream OpenIPC video. Simply setup your keys and desired channel, give the system a reboot, and after the stream will begin automatically on plug-in.

How to flash the image to your onboard emmc

On first boot, connect a keyboard and login is root/root (user/password is radxa/radxa)

Run ./resizefs.sh to repartition and resize your filesystem. Ignore all the red text and let the script finish.

Stock settings will set the display to 1920x1080@60fps. You will want to change this behavior in the screen-mode file in the scripts folder found in your home directory. -- sudo nano /home/radxa/screen-mode
e.g. for HDZ goggles -- change to 1280x720@100

You can use the handy wifi-connect.sh script found in the scripts folder in the radxa home directory. Run the script with your home network name and password as follows: ./wifi-connect.sh NetworkName NetworkPassword. Replace NetworkName and NetworkPassword with your home network credentials.

You can also manually setup the onboard wifi for SSH connectivity. (udev rules and networkmanager are already configured in this image, you only need to execute the nmcli commands)

This image includes DVR functionality; It requires a push button to be installed to the gpio header between physical pins 25 and 27 like so:

DVR is saved to the Videos folder in your home directory. DVR can be accessed either at /home/radxa/Videos or via a media server. Connect your groundstation to your home network and it can be accessed via a web browser at x.x.x.x:8080 -- replace x.x.x.x with your groundstation's local ip address.

Assets 5

15 Jul 23:53

JohnDGodwin

zero3w-v1.5.0

23e4a23

Radxa Zero 3w w/ OpenIPC v1.5.0

V1.5.0 Release Notes:
*8GB emmc is now supported
*default gs.key and drone.key files are now included

This image uses the FPVue project rather than pure gstreamer to display the video. It includes an OSD as well as DVR video recording. (OSD is NOT recorded, only displayed to the screen)

On first boot, the stream will not start to give the user the ability to set up the system. Please perform the following steps.

Step 1 - Flash the image to either your onboard emmc or a micro SD card.
Step 2 - Connect a screen and a wired keyboard to your radxa (you may need a usb-a to usb-c adapter or hub) and boot the system.
Step 3 - The system should boot to a CLI. Login as either radxa/radxa or root/root (I personally use the radxa user but some prefer using the root account. EVERYTHING IS LOCATED AT /home/radxa)
Step 4 - Run ./resizefs.sh to repartition and resize your filesystem. Ignore the red warning text and let the script finish.
Step 5 - Use the onboard wifi to connect to your home network:
Method 1: Enter nmtui, go down to Activate a connection and activate one of the detected wifi networks.
Method 2: While in the scripts folder, run the wifi-connect.sh script with your home network name and password as follows: ./wifi-connect.sh NetworkName NetworkPassword. Replace NetworkName and NetworkPassword with your home network credentials.
To check your connection after, run nmcli and your wlan0 connection should be green. Make a note of your ip address. We will need this to ssh into the system later.
Step 6 - Set your desired screen resolution and refresh rate in the screen-mode file. sudo nano /home/radxa/scripts/screen-mode and change to your desired specifications. Format is WxH@fps -- Common values would be 1920x1080@60, 1920x1080@120. 1280x720@60, 1280x720@120
Step 7 - Set your WFB-ng channel in /etc/wifibroadcast.cfg and transfer your gs.key to /etc (A standard gs.key and drone.key are now provided)
Step 8 - Shutdown the system, disconnect the keyboard, and connect your wifi card. Boot the system and SSH from a separate computer.
Step 9 - Test the system. Run wfb-cli gs and plug in your camera. Make sure you are properly getting video and telemetry packets. Hit CTRL-C to exit the wfb-cli. Run sudo systemctl start openipc.service and the display connected to the radxa should change to your video feed with OSD. Press your DVR button. The stream should stop (the screen will go black for a second) and a new stream being recorded should start. Press the dvr button again to stop the saving stream and go back to the display stream. (Again, the stream should go black for a second. If it doesn't, press the button again) Confirm there is a .mp4 video file in home/radxa/Videos by going to x.x.x.x:8080 in a browser, replacing x.x.x.x with your radxa's ip address. . Run sudo systemctl stop openipc.service to stop testing.
Step 10 - Last and final step. Once you have confirmed the system is working and you have set your desired settings, run sudo systemctl enable openipc.service to have the stream begin on boot.

This is a prebuilt image for the Radxa Zero 3w to stream OpenIPC video. Simply setup your keys and desired channel, give the system a reboot, and after the stream will begin automatically on plug-in.

How to flash the image to your onboard emmc

On first boot, connect a keyboard and login is root/root (user/password is radxa/radxa)

Run ./resizefs.sh to repartition and resize your filesystem. Ignore all the red text and let the script finish.

Stock settings will set the display to 1920x1080@60fps. You will want to change this behavior in the screen-mode file in the scripts folder found in your home directory. -- sudo nano /home/radxa/screen-mode
e.g. for HDZ goggles -- change to 1280x720@100

You can also manually setup the onboard wifi for SSH connectivity. (udev rules and networkmanager are already configured in this image, you only need to execute the nmcli commands)

This image includes DVR functionality; It requires a push button to be installed to the gpio header between physical pins 25 and 27 like so:

Assets 5

02 May 01:31

JohnDGodwin

zero3w-v1.5.0-rc2

23e4a23

Radxa Zero 3w w/ OpenIPC v1.5.0-rc2 Pre-release

Pre-release

Pre-Release Notes:
This image uses the FPVue project rather than pure gstreamer to display the video. It includes an OSD as well as DVR video recording. (OSD is NOT recorded, only displayed to the screen)
On first boot, the stream will not start to give the user the ability to set up the system. Please perform the following steps.

Step 1 - Flash the image to either your onboard emmc or a micro SD card. (do not flash to 8gb emmc, it may not boot because of a sizing issue)
Step 2 - Connect a screen and a wired keyboard to your radxa (you may need a usb-a to usb-c adapter or hub) and boot the system.
Step 3 - The system should boot to a CLI. Login as either radxa/radxa or root/root (I personally use the radxa user but some prefer using the root account. EVERYTHING IS LOCATED AT /home/radxa)
Step 4 - Run ./resizefs.sh to repartition and resize your filesystem. Ignore all the red text and let the script finish.
Step 5 - Use the onboard wifi to connect to your home network: while in the scripts folder, run the wifi-connect.sh script with your home network name and password as follows: ./wifi-connect.sh NetworkName NetworkPassword. Replace NetworkName and NetworkPassword with your home network credentials. To check your connection after, run nmcli and your wlan1 connection should be green. Make a note of your ip address. We will need this to ssh into the system later.
Step 6 - Set your desired screen resolution and refresh rate in the screen-mode file. sudo nano screen-mode and change to your desired specifications. Format is WxH@fps -- Common values would be 1920x1080@60, 1920x1080@120. 1280x720@60, 1280x720@120
Step 7 - Set your WFB-ng channel in /etc/wifibroadcast.cfg and transfer your gs.key to /etc
Step 8 - Shutdown the system, disconnect the keyboard, and connect your wifi card. Boot the system and SSH from a separate computer.
Step 9 - Test the system. Run wfb-cli gs and plug in your camera. Make sure you are properly getting video and telemetry packets. Hit CTRL-C to exit the wfb-cli. Run sudo systemctl start openipc.service and the display connected to the radxa should change to your video feed with OSD. Press your DVR button. The stream should stop and a new stream being recorded should start. Press the dvr button again to stop the saving stream and go back to the display stream. Confirm there is a .ts video file in home/radxa/Videos. Run sudo systemctl stop openipc.service to stop testing.
Step 10 - Last and final step. Once you have confirmed the system is working and you have set your desired settings, run sudo systemctl enable openipc.service to have the stream begin on boot.

This is a prebuilt image for the Radxa Zero 3w to stream OpenIPC video. Simply setup your keys and desired channel, give the system a reboot, and after the stream will begin automatically on plug-in.

How to flash the image to your onboard emmc

On first boot, connect a keyboard and login is root/root (user/password is radxa/radxa)

Run ./resizefs.sh to repartition and resize your filesystem. Ignore all the red text and let the script finish.

Stock settings will set the display to 1920x1080@60fps. You will want to change this behavior in the screen-mode file in the scripts folder found in your home directory. -- sudo nano /home/radxa/screen-mode
e.g. for HDZ goggles -- change to 1280x720@100

You can also manually setup the onboard wifi for SSH connectivity. (udev rules and networkmanager are already configured in this image, you only need to execute the nmcli commands)

This image includes DVR functionality; It requires a push button to be installed to the gpio header between physical pins 25 and 27 like so:

Assets 3

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Releases: OpenIPC/sbc-groundstations

Orange Pi 3b + 5(plus) w/ OpenIPC

Radxa Zero 3w w/ OpenIPC v1.8.3

Radxa Zero 3w w/ OpenIPC v1.8.2

Radxa Zero 3w w/ OpenIPC v1.8.1

Radxa Zero 3w w/ OpenIPC v1.8.0

Radxa Zero 3w w/ OpenIPC v1.8.0-rc1

Radxa Zero 3w w/ OpenIPC v1.7.0

Radxa Zero 3w w/ OpenIPC v1.6.0

Radxa Zero 3w w/ OpenIPC v1.5.0

Radxa Zero 3w w/ OpenIPC v1.5.0-rc2