digipot9

---

DIGI POT 9 Click

DIGI POT 9 Click demo application is developed using the NECTO Studio, ensuring compatibility with mikroSDK's open-source libraries and tools. Designed for plug-and-play implementation and testing, the demo is fully compatible with all development, starter, and mikromedia boards featuring a mikroBUS™ socket.

---

Click Library

• Author : Stefan Filipovic
• Date : Jun 2021.
• Type : SPI type

Software Support

Example Description

This example demonstrates the use of DIGI POT 9 Click board.

Example Libraries

• MikroSDK.Board
• MikroSDK.Log
• Click.DIGIPOT9

Example Key Functions

• digipot9_cfg_setup Config Object Initialization function.

void digipot9_cfg_setup ( digipot9_cfg_t *cfg );

• digipot9_init Initialization function.

err_t digipot9_init ( digipot9_t *ctx, digipot9_cfg_t *cfg );

• digipot9_default_cfg Click Default Configuration function.

void digipot9_default_cfg ( digipot9_t *ctx );

• digipot9_generic_write This function writes two data bytes to the selected command and address by using SPI serial interface.

err_t digipot9_generic_write ( digipot9_t *ctx, uint8_t command, uint8_t address, uint16_t data_in );

• digipot9_generic_read This function reads two data bytes from the selected command and address by using SPI serial interface.

err_t digipot9_generic_read ( digipot9_t *ctx, uint8_t command, uint8_t address, uint16_t *data_out );

• digipot9_set_wiper_1 This function sets wiper 1 to desired value.

err_t digipot9_set_wiper_1 ( digipot9_t *ctx, uint16_t data_in );

Application Init

Initializes the driver and makes an initial log.

void application_init ( void )
{
    log_cfg_t log_cfg;            /**< Logger config object. */
    digipot9_cfg_t digipot9_cfg;  /**< Click config object. */

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, " Application Init " );

    // Click initialization.

    digipot9_cfg_setup( &digipot9_cfg );
    DIGIPOT9_MAP_MIKROBUS( digipot9_cfg, MIKROBUS_1 );
    err_t init_flag  = digipot9_init( &digipot9, &digipot9_cfg );
    if ( SPI_MASTER_ERROR == init_flag ) 
    {
        log_error( &logger, " Application Init Error. " );
        log_info( &logger, " Please, run program again... " );

        for ( ; ; );
    }

    digipot9_default_cfg ( &digipot9 );
    log_info( &logger, " Application Task " );
}

Application Task

Iterates through the entire wiper range and sets both wipers to the iterator value once per second. The current wiper position will be displayed on the USB UART.

void application_task ( void )
{
    for ( uint16_t cnt = DIGIPOT9_WIPER_ZERO_SCALE; cnt <= DIGIPOT9_WIPER_FULL_SCALE; cnt += 50 )
    {
        digipot9_set_wiper_1 ( &digipot9, cnt );
        digipot9_set_wiper_2 ( &digipot9, cnt );
        log_printf( &logger, " * Wipers position set to %u *\r\n", cnt );
        
        Delay_ms ( 1000 );
    }
}

Application Output

This Click board can be interfaced and monitored in two ways:

• Application Output - Use the "Application Output" window in Debug mode for real-time data monitoring. Set it up properly by following this tutorial.
• UART Terminal - Monitor data via the UART Terminal using a USB to UART converter. For detailed instructions, check out this tutorial.

Additional Notes and Information

The complete application code and a ready-to-use project are available through the NECTO Studio Package Manager for direct installation in the NECTO Studio. The application code can also be found on the MIKROE GitHub account.

---