-
Notifications
You must be signed in to change notification settings - Fork 4
/
Copy pathd2d_emulator_setup.txt
107 lines (89 loc) · 3.72 KB
/
d2d_emulator_setup.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
Scenario 1 : Off-network UE2UE link
SynchREF UE (UE1)
UE1(eth0 - 10.10.10.1)--------UE2(eno1 - 10.10.10.2)
Here's an example of /etc/network/interfaces configuration for UE1
auto eth0
iface eth0 inet static
address 10.10.10.1
netmask 255.255.255.0
gateway 10.10.10.1
Prepare the environment:
- git clone https://gitlab.eurecom.fr/matzakos/LTE-D2D.git #branch: master
This branch contains all the current development for DDPS
- UE MAC<-> UE MAC for Scenario 1
- eNB MAC<->UE MAC (NFAPI Transport)
- RRC Extensions for “on-network” cases
NFAPI configuration (required even for Scenario 1 target)
- git clone https://github.com/cisco/open-nFAPI.git
- cd open-nfapi
- patch -p1 --dry-run < $OPENAIR_HOME/open-nfapi.oai.patch
Validate that there are no errors
- patch -p1 < $OPENAIR_HOME/open-nfapi.oai.patch
OAI build/execute
- export NFAPI_DIR=XXX (place where NFAPI was installed)
- cd cmake_targets
- ./build_oai --UE
(if necessary, use ./build_oai -I --UE to install required packages)
- cd lte_build_oai/build/
- cp ../../../targets/bin/.ue* .
- cp ../../../targets/bin/.usim* .
- sudo insmod ../../../targets/bin/ue_ip.ko
UE1:
- sudo ifconfig oip0 10.0.0.1
- sudo iptables -A POSTROUTING -t mangle -o oip0 -d 224.0.0.3 -j MARK --set-mark 3
- (if necessary) sudo route add default gw 10.10.10.1 eth0
UE2:
- sudo ifconfig oip0 10.0.0.2
- sudo iptables -A POSTROUTING -t mangle -o oip0 -d 224.0.0.3 -j MARK --set-mark 3
- (if necessary) sudo route add default gw 10.10.10.1 eno1
UE1 and UE2: Get and build vencore_app from d2d-l3-stub (branch: l3_stub)
- gcc -I . vencore_app.c -o vencore_app -lpthread
--------------------------------
TEST ONE-TO-MANY
Run UE1 then UE2, for example:
UE1: sudo ./lte-softmodem-stub -U --emul-iface eth0
UE2: sudo ./lte-softmodem-stub -U --emul-iface eno1
Test with Ping
- Sender - UE1: ping -I oip0 224.0.0.3
- Receiver - UE2: using wireshark
Test with Iperf
- Sender - UE1: iperf -c 224.0.0.3 -u -b 0.1M --bind 10.0.0.1 -t 100
- Receiver - UE2: sudo ./mcreceive 224.0.0.3 5001
Filter the incomming packets according to GroupL2Id: receiver (one-to-many) can discard the packets if it doesn't belong to this group.
For the moment, both sender and receiver use the same set of Ids (hardcoded)
UE1 (sender)
- sudo ./lte-softmodem-stub -U --emul-iface eth0
- ./vencore_app #send the sourceL2Id, groupL2Id to OAI
- ping -I oip0 224.0.0.3
UE2(receiver)
- sudo ./lte-softmodem-stub -U --emul-iface eno1
#we can see the incomming packets from OAI log, however, cannot see from Wireshark -> they are discarded at MAC layer
- ./vencore_app #we can see the packets appearing in Wireshark
--------------------------------------
TEST PC5-S (UE1 -sender, UE2 - receiver) and PC5-U for ONE-TO-ONE scenario
Configure UE1/UE2
UE1:
- sudo ifconfig oip0 10.0.0.1
- sudo iptables -A POSTROUTING -t mangle -o oip0 -d 10.0.0.2 -j MARK --set-mark 3
- sudo route add default gw 10.10.10.1 eth0
UE2:
- sudo ifconfig oip0 10.0.0.2
- sudo iptables -A POSTROUTING -t mangle -o oip0 -d 10.0.0.1 -j MARK --set-mark 3
- sudo route add default gw 10.10.10.1 eno1
step 1:
- UE1: sudo ./lte-softmodem-stub -U --emul-iface eth0
step 2:
- UE2: sudo ./lte-softmodem-stub -U --emul-iface eno1
- UE2: ./vencore_app -r #listen to incomming message from PC5-S
step 3:
- UE1: ./vencore_app -s #send a message via PC5-S (e.g., DirectCommunicationRequest)
Generate unicast traffic
UE1: ping -I oip0 10.0.0.2
--------------------------------------
TEST PC5-D
step 1:
- UE1: sudo ./lte-softmodem-stub -U --emul-iface eth0
- UE1: ./vencore_app -d #send a PC5-Discovery-Announcement via PC5D
step 2:
- UE2: sudo ./lte-softmodem-stub -U --emul-iface eno1
- UE2: ./vencore_app -d #send a PC5-Discovery-Announcement via PC5D