System Data Error! #2377

malgates · 2024-11-12T21:17:58Z

malgates
Nov 12, 2024

Hi Everyone,

I think took a wrong exit while flashing the device. So i followed this video right until the section for the setting up the blueprint. Instead i jumped that step and flashed it deirectly without setting up the blueprint. I think I was a too tired when doing the flash.

So the device showed the old screen, when I realized my mistake. I hit "update TFT" in Home Assistant and it flashed the display, but it left me with a blue screen that only shows "System Data Error!". No problem I thought and reflashed the device again via serial with the modified blueprint. Flash worked, but still the same screen. The device is present in ESPHome and here are some logs:

INFO ESPHome 2024.10.2
INFO Reading configuration /config/esphome/ns-panel-wei.yaml...
INFO Updating https://github.com/Blackymas/NSPanel_HA_Blueprint@main
INFO Updating https://github.com/Blackymas/[email protected]
INFO Detected timezone 'Europe/Berlin'
INFO Starting log output from 192.168.1.123 using esphome API
INFO Successfully connected to nspanelwhite @ 192.168.1.123 in 0.078s
INFO Successful handshake with nspanelwhite @ 192.168.1.123 in 0.034s
[22:07:24][I][app:100]: ESPHome version 2024.10.2 compiled on Nov 12 2024, 21:53:16
[22:07:24][I][app:102]: Project esphome.NSPanel_HA_Blueprint version 4.3.12
[22:07:24][C][wifi:600]: WiFi:
[22:07:24][C][wifi:428]: Local MAC: A0:B7:65:54:CA:B8
[22:07:24][C][wifi:433]: SSID: [redacted]
[22:07:24][C][wifi:436]: IP Address: 192.168.1.123
[22:07:24][C][wifi:440]: BSSID: [redacted]
[22:07:24][C][wifi:441]: Hostname: 'nspanelwhite'
[22:07:24][C][wifi:443]: Signal strength: -58 dB ▂▄▆█
[22:07:24][C][wifi:447]: Channel: 1
[22:07:24][C][wifi:448]: Subnet: 255.255.255.0
[22:07:24][C][wifi:449]: Gateway: 192.168.1.1
[22:07:24][C][wifi:450]: DNS1: 192.168.1.140
[22:07:24][C][wifi:451]: DNS2: 0.0.0.0
[22:07:24][W][nextion:431]: Nextion reported variable name invalid!
[22:07:24][W][nextion:431]: Nextion reported variable name invalid!
[22:07:24][C][logger:185]: Logger:
[22:07:24][C][logger:186]: Level: DEBUG
[22:07:24][C][logger:188]: Log Baud Rate: 0
[22:07:24][C][logger:189]: Hardware UART: UART0
[22:07:24][C][uart.idf:159]: UART Bus 0:
[22:07:24][C][uart.idf:160]: TX Pin: GPIO16
[22:07:24][C][uart.idf:161]: RX Pin: GPIO17
[22:07:24][C][uart.idf:163]: RX Buffer Size: 256
[22:07:24][C][uart.idf:165]: Baud Rate: 115200 baud
[22:07:24][C][uart.idf:166]: Data Bits: 8
[22:07:24][C][uart.idf:167]: Parity: NONE
[22:07:24][C][uart.idf:168]: Stop bits: 1
[22:07:24][C][ledc.output:180]: LEDC Output:
[22:07:24][C][ledc.output:181]: Pin GPIO21
[22:07:24][C][ledc.output:182]: LEDC Channel: 0
[22:07:24][C][ledc.output:183]: PWM Frequency: 1000.0 Hz
[22:07:24][C][ledc.output:184]: Phase angle: 0.0°
[22:07:24][C][ledc.output:185]: Bit depth: 16
[22:07:24][C][template.binary_sensor:028]: Template Binary Sensor 'Nextion display'
[22:07:24][C][template.binary_sensor:028]: Device Class: 'connectivity'
[22:07:24][C][template.number:050]: Template Number 'Display Brightness'
[22:07:24][C][template.number:050]: Unit of Measurement: '%'
[22:07:24][C][template.number:051]: Optimistic: YES
[22:07:24][C][template.number:052]: Update Interval: 60.0s
[22:07:24][C][template.number:050]: Template Number 'Display Brightness Dimdown'
[22:07:24][C][template.number:050]: Unit of Measurement: '%'
[22:07:24][C][template.number:051]: Optimistic: YES
[22:07:24][C][template.number:052]: Update Interval: 60.0s
[22:07:24][C][template.number:050]: Template Number 'Display Brightness Sleep'
[22:07:24][C][template.number:050]: Unit of Measurement: '%'
[22:07:24][C][template.number:051]: Optimistic: YES
[22:07:24][C][template.number:052]: Update Interval: 60.0s
[22:07:24][C][template.number:050]: Template Number 'Temperature Correction'
[22:07:24][C][template.number:050]: Unit of Measurement: '°C'
[22:07:24][C][template.number:051]: Optimistic: YES
[22:07:24][C][template.number:052]: Update Interval: 60.0s
[22:07:24][C][template.number:050]: Template Number 'Timeout Page'
[22:07:24][C][template.number:050]: Icon: 'mdi:timer'
[22:07:24][C][template.number:050]: Unit of Measurement: 's'
[22:07:24][C][template.number:051]: Optimistic: YES
[22:07:24][C][template.number:052]: Update Interval: 60.0s
[22:07:24][C][template.number:050]: Template Number 'Timeout Dimming'
[22:07:24][C][template.number:050]: Icon: 'mdi:timer'
[22:07:24][C][template.number:050]: Unit of Measurement: 's'
[22:07:24][C][template.number:051]: Optimistic: YES
[22:07:24][C][template.number:052]: Update Interval: 60.0s
[22:07:24][C][template.number:050]: Template Number 'Timeout Sleep'
[22:07:24][C][template.number:050]: Icon: 'mdi:timer'
[22:07:24][C][template.number:050]: Unit of Measurement: 's'
[22:07:24][C][template.number:051]: Optimistic: YES
[22:07:24][C][template.number:052]: Update Interval: 60.0s
[22:07:24][C][template.select:065]: Template Select 'Baud rate'
[22:07:24][C][template.select:065]: Icon: 'mdi:swap-horizontal'
[22:07:24][C][template.select:066]: Update Interval: 60.0s
[22:07:24][C][template.select:069]: Optimistic: YES
[22:07:24][C][template.select:070]: Initial Option: 115200
[22:07:24][C][template.select:071]: Restore Value: YES
[22:07:24][C][template.select:065]: Template Select 'Wake-up page'
[22:07:24][C][template.select:065]: Icon: 'mdi:page-next-outline'
[22:07:24][C][template.select:066]: Update Interval: 60.0s
[22:07:24][C][template.select:069]: Optimistic: YES
[22:07:24][C][template.select:070]: Initial Option: home
[22:07:24][C][template.select:071]: Restore Value: YES
[22:07:24][C][template.select:065]: Template Select 'Update TFT display - Model'
[22:07:24][C][template.select:065]: Icon: 'mdi:file-sync'
[22:07:24][C][template.select:066]: Update Interval: 60.0s
[22:07:24][C][template.select:069]: Optimistic: YES
[22:07:24][C][template.select:070]: Initial Option: NSPanel EU
[22:07:24][C][template.select:071]: Restore Value: YES
[22:07:24][C][template.select:065]: Template Select 'Update TFT display - Baud rate'
[22:07:24][C][template.select:065]: Icon: 'mdi:swap-horizontal'
[22:07:24][C][template.select:066]: Update Interval: 60.0s
[22:07:24][C][template.select:069]: Optimistic: YES
[22:07:24][C][template.select:070]: Initial Option: 921600
[22:07:24][C][template.select:071]: Restore Value: YES
[22:07:24][C][switch.gpio:068]: GPIO Switch 'Nextion display - Power'
[22:07:24][C][switch.gpio:091]: Restore Mode: always ON
[22:07:24][C][switch.gpio:031]: Pin: GPIO4
[22:07:24][C][template.text_sensor:020]: Template Sensor 'Device Name'
[22:07:24][C][template.text_sensor:020]: Icon: 'mdi:identifier'
[22:07:24][C][template.text_sensor:020]: Template Sensor 'Detailed Entity'
[22:07:24][C][template.text_sensor:020]: Icon: 'mdi:tablet-dashboard'
[22:07:24][C][template.text_sensor:020]: Template Sensor 'Notification Label'
[22:07:24][C][template.text_sensor:020]: Template Sensor 'Notification Text'
[22:07:24][C][template.text_sensor:020]: Template Sensor 'Version Blueprint'
[22:07:24][C][template.text_sensor:020]: Icon: 'mdi:tag-text-outline'
[22:07:24][C][template.text_sensor:020]: Template Sensor 'Version ESPHome'
[22:07:24][C][template.text_sensor:020]: Icon: 'mdi:tag-text-outline'
[22:07:24][C][template.sensor:022]: Template Sensor 'Blueprint'
[22:07:24][C][template.sensor:022]: State Class: ''
[22:07:24][C][template.sensor:022]: Unit of Measurement: '%'
[22:07:24][C][template.sensor:022]: Accuracy Decimals: 1
[22:07:24][C][template.sensor:022]: Icon: 'mdi:link-variant'
[22:07:24][C][template.sensor:023]: Update Interval: 60.0s
[22:07:24][C][gpio.binary_sensor:015]: GPIO Binary Sensor 'Left Button'
[22:07:24][C][gpio.binary_sensor:016]: Pin: GPIO14
[22:07:24][C][gpio.binary_sensor:015]: GPIO Binary Sensor 'Right Button'
[22:07:24][C][gpio.binary_sensor:016]: Pin: GPIO27
[22:07:24][C][switch.gpio:068]: GPIO Switch 'Relay 1'
[22:07:24][C][switch.gpio:091]: Restore Mode: restore defaults to OFF
[22:07:24][C][switch.gpio:031]: Pin: GPIO22
[22:07:24][C][switch.gpio:068]: GPIO Switch 'Relay 2'
[22:07:24][C][switch.gpio:091]: Restore Mode: restore defaults to OFF
[22:07:24][C][switch.gpio:031]: Pin: GPIO19
[22:07:25][C][template.switch:068]: Template Switch 'Notification unread'
[22:07:25][C][template.switch:091]: Restore Mode: always OFF
[22:07:25][C][template.switch:057]: Optimistic: YES
[22:07:25][C][template.switch:068]: Template Switch 'Notification sound'
[22:07:25][C][template.switch:091]: Restore Mode: restore defaults to OFF
[22:07:25][C][template.switch:057]: Optimistic: YES
[22:07:25][C][template.switch:068]: Template Switch 'Relay 0 (dummy)'
[22:07:25][C][template.switch:091]: Restore Mode: always OFF
[22:07:25][C][template.switch:057]: Optimistic: YES
[22:07:25][C][psram:020]: PSRAM:
[22:07:25][C][psram:021]: Available: YES
[22:07:25][C][psram:024]: Size: 2036 KB
[22:07:25][C][rtttl:029]: Rtttl
[22:07:25][C][nextion:138]: Nextion:
[22:07:25][C][nextion:142]: Device Model: NX4832F035_011C
[22:07:25][C][nextion:143]: Firmware Version: 110
[22:07:25][C][nextion:144]: Serial Number: 17B1340187B9A638
[22:07:25][C][nextion:145]: Flash Size: 16777216
[22:07:25][C][nextion:147]: Wake On Touch: YES
[22:07:25][C][nextion:148]: Exit reparse: YES
[22:07:25][C][factory_reset.button:011]: Factory Reset Button 'Factory reset'
[22:07:25][C][factory_reset.button:011]: Icon: 'mdi:restart-alert'
[22:07:25][C][restart.button:017]: Restart Button 'Restart'
[22:07:25][C][restart.button:017]: Icon: 'mdi:restart'
[22:07:25][C][adc:097]: ADC Sensor 'ntc_source'
[22:07:25][C][adc:097]: Device Class: 'voltage'
[22:07:25][C][adc:097]: State Class: 'measurement'
[22:07:25][C][adc:097]: Unit of Measurement: 'V'
[22:07:25][C][adc:097]: Accuracy Decimals: 2
[22:07:25][C][adc:107]: Pin: GPIO38
[22:07:25][C][adc:122]: Attenuation: 12db
[22:07:25][C][adc:141]: Samples: 4
[22:07:25][C][adc:142]: Update Interval: 10.0s
[22:07:25][C][resistance:010]: Resistance Sensor 'resistance_sensor'
[22:07:25][C][resistance:010]: State Class: 'measurement'
[22:07:25][C][resistance:010]: Unit of Measurement: 'Ω'
[22:07:25][C][resistance:010]: Accuracy Decimals: 1
[22:07:25][C][resistance:010]: Icon: 'mdi:flash'
[22:07:25][C][resistance:011]: Configuration: DOWNSTREAM
[22:07:25][C][resistance:012]: Resistor: 11200.00Ω
[22:07:25][C][resistance:013]: Reference Voltage: 3.3V
[22:07:25][C][ntc:014]: NTC Sensor 'Temperature'
[22:07:25][C][ntc:014]: Device Class: 'temperature'
[22:07:25][C][ntc:014]: State Class: 'measurement'
[22:07:25][C][ntc:014]: Unit of Measurement: '°C'
[22:07:25][C][ntc:014]: Accuracy Decimals: 1
[22:07:25][C][thermostat.climate:1296]: Thermostat 'Thermostat'
[22:07:25][C][thermostat.climate:1301]: Start-up Delay Enabled: NO
[22:07:25][C][thermostat.climate:1317]: Heating Parameters:
[22:07:25][C][thermostat.climate:1318]: Deadband: 0.5°C
[22:07:25][C][thermostat.climate:1319]: Overrun: 0.5°C
[22:07:25][C][thermostat.climate:1326]: Minimum Off Time: 300s
[22:07:25][C][thermostat.climate:1328]: Minimum Run Time: 300s
[22:07:25][C][thermostat.climate:1343]: Minimum Idle Time: 30s
[22:07:25][C][thermostat.climate:1344]: Supports AUTO: NO
[22:07:25][C][thermostat.climate:1345]: Supports HEAT/COOL: NO
[22:07:25][C][thermostat.climate:1346]: Supports COOL: NO
[22:07:25][C][thermostat.climate:1347]: Supports DRY: NO
[22:07:25][C][thermostat.climate:1348]: Supports FAN_ONLY: NO
[22:07:25][C][thermostat.climate:1350]: Supports FAN_ONLY_ACTION_USES_FAN_MODE_TIMER: NO
[22:07:25][C][thermostat.climate:1351]: Supports FAN_ONLY_COOLING: NO
[22:07:25][C][thermostat.climate:1356]: Supports FAN_WITH_HEATING: NO
[22:07:25][C][thermostat.climate:1358]: Supports HEAT: YES
[22:07:25][C][thermostat.climate:1359]: Supports FAN MODE ON: NO
[22:07:25][C][thermostat.climate:1360]: Supports FAN MODE OFF: NO
[22:07:25][C][thermostat.climate:1361]: Supports FAN MODE AUTO: NO
[22:07:25][C][thermostat.climate:1362]: Supports FAN MODE LOW: NO
[22:07:25][C][thermostat.climate:1363]: Supports FAN MODE MEDIUM: NO
[22:07:25][C][thermostat.climate:1364]: Supports FAN MODE HIGH: NO
[22:07:25][C][thermostat.climate:1365]: Supports FAN MODE MIDDLE: NO
[22:07:25][C][thermostat.climate:1366]: Supports FAN MODE FOCUS: NO
[22:07:25][C][thermostat.climate:1367]: Supports FAN MODE DIFFUSE: NO
[22:07:25][C][thermostat.climate:1368]: Supports FAN MODE QUIET: NO
[22:07:25][C][thermostat.climate:1369]: Supports SWING MODE BOTH: NO
[22:07:25][C][thermostat.climate:1370]: Supports SWING MODE OFF: NO
[22:07:25][C][thermostat.climate:1371]: Supports SWING MODE HORIZONTAL: NO
[22:07:25][C][thermostat.climate:1372]: Supports SWING MODE VERTICAL: NO
[22:07:25][C][thermostat.climate:1373]: Supports TWO SET POINTS: NO
[22:07:25][C][thermostat.climate:1375]: Supported PRESETS:
[22:07:25][C][thermostat.climate:1379]: Supports HOME: YES
[22:07:25][C][thermostat.climate:963]: HOME Is Default: NO
[22:07:25][C][thermostat.climate:970]: HOME Default Target Temperature Low: 18.0°C
[22:07:25][C][thermostat.climate:984]: HOME Default Mode: HEAT
[22:07:25][C][thermostat.climate:1383]: Supported CUSTOM PRESETS:
[22:07:25][C][thermostat.climate:1387]: Supports Off: YES
[22:07:25][C][thermostat.climate:963]: Off Is Default: YES
[22:07:25][C][thermostat.climate:970]: Off Default Target Temperature Low: 18.0°C
[22:07:25][C][thermostat.climate:984]: Off Default Mode: OFF
[22:07:25][C][thermostat.climate:1391]: On boot, restore from: MEMORY
[22:07:25][C][homeassistant.time:010]: Home Assistant Time:
[22:07:25][C][homeassistant.time:011]: Timezone: 'CET-1CEST,M3.5.0,M10.5.0/3'
[22:07:25][C][mdns:116]: mDNS:
[22:07:25][C][mdns:117]: Hostname: nspanelwhite
[22:07:25][C][esphome.ota:073]: Over-The-Air updates:
[22:07:25][C][esphome.ota:074]: Address: nspanelwhite.local:3232
[22:07:25][C][esphome.ota:075]: Version: 2
[22:07:25][C][esphome.ota:078]: Password configured
[22:07:25][C][safe_mode:018]: Safe Mode:
[22:07:25][C][safe_mode:020]: Boot considered successful after 60 seconds
[22:07:25][C][safe_mode:021]: Invoke after 3 boot attempts
[22:07:25][C][safe_mode:023]: Remain in safe mode for 180 seconds
[22:07:25][C][api:140]: API Server:
[22:07:25][C][api:141]: Address: nspanelwhite.local:6053
[22:07:25][C][api:145]: Using noise encryption: NO
[22:07:26][C][wifi_signal.sensor:010]: WiFi Signal 'RSSI'
[22:07:26][C][wifi_signal.sensor:010]: Device Class: 'signal_strength'
[22:07:26][C][wifi_signal.sensor:010]: State Class: 'measurement'
[22:07:26][C][wifi_signal.sensor:010]: Unit of Measurement: 'dBm'
[22:07:26][C][wifi_signal.sensor:010]: Accuracy Decimals: 0
[22:07:26][C][wifi_signal.sensor:010]: Icon: 'mdi:wifi'
[22:07:28][D][sensor:094]: 'ntc_source': Sending state 1.75717 V with 2 decimals of accuracy
[22:07:28][D][resistance:039]: 'resistance_sensor' - Resistance 12755.9Ω
[22:07:28][D][sensor:094]: 'resistance_sensor': Sending state 12755.92773 Ω with 1 decimals of accuracy
[22:07:28][D][ntc:026]: 'Temperature' - Temperature: 19.6°C
[22:07:28][D][sensor:094]: 'Temperature': Sending state 19.62094 °C with 1 decimals of accuracy
[22:07:28][D][climate:396]: 'Thermostat' - Sending state:
[22:07:28][D][climate:399]: Mode: OFF
[22:07:28][D][climate:401]: Action: OFF
[22:07:28][D][climate:419]: Current Temperature: 19.62°C
[22:07:28][D][climate:425]: Target Temperature: 22.00°C
[22:07:28][W][component:237]: Component adc.sensor took a long time for an operation (53 ms).
[22:07:28][W][component:238]: Components should block for at most 30 ms.
[22:07:28][W][nextion:431]: Nextion reported variable name invalid!
[22:07:28][W][nextion:431]: Nextion reported variable name invalid!
[22:07:28][W][nextion:431]: Nextion reported variable name invalid!
[22:07:28][W][nextion:431]: Nextion reported variable name invalid!
[22:07:28][W][nextion:431]: Nextion reported variable name invalid!
[22:07:28][W][nextion:431]: Nextion reported variable name invalid!
[22:07:28][W][nextion:431]: Nextion reported variable name invalid!
[22:07:28][W][nextion:431]: Nextion reported variable name invalid!
[22:07:30][W][nextion:431]: Nextion reported variable name invalid!
[22:07:30][W][nextion:431]: Nextion reported variable name invalid!
[22:07:30][W][nextion:431]: Nextion reported variable name invalid!
[22:07:31][W][nextion:431]: Nextion reported variable name invalid!
[22:07:34][C][nspanel_ha_blueprint:2224]: Wi-Fi: Good (-56 dBm)
[22:07:34][C][nspanel_ha_blueprint:2235]: API: Connected
[22:07:34][C][nspanel_ha_blueprint:2243]: Blueprint:
[22:07:34][C][nspanel_ha_blueprint:2245]: Version: 4.3.11
[22:07:34][C][nspanel_ha_blueprint:2246]: Init steps: 62 (100.0%)
[22:07:34][C][nspanel_ha_blueprint:2255]: ESPHome:
[22:07:34][C][nspanel_ha_blueprint:2256]: Version: 4.3.12
[22:07:34][C][nspanel_ha_blueprint:2257]: Compiler: 2024.10.2
[22:07:34][C][nspanel_ha_blueprint:2262]: Framework: ESP-IDF
[22:07:34][C][nspanel_ha_blueprint:2267]: Free heap:
[22:07:34][C][nspanel_ha_blueprint:2271]: Internal: 197856 bytes (56.3%)
[22:07:34][C][nspanel_ha_blueprint:2281]: PSRAM: 1985443 bytes (95.2%)
[22:07:34][C][nspanel_ha_blueprint:2288]: UART:
[22:07:34][C][nspanel_ha_blueprint:2289]: Baud rate: 115200 bps
[22:07:34][C][nspanel_ha_blueprint:2290]: Queue size: 0
[22:07:34][C][nspanel_ha_blueprint:2294]: Nextion:

and so on. What I find really strange is, that there seems no FW on the display. THe buttons respond to what I set them up to, but not the display. Any ideas?

THX

Answered by malgates

Nov 13, 2024

OK I officially had a DNS problem. THANKS for pointing that out! BOG THX for the help!

I was able to flash the NSPanel Blank. Currently trying the EU one.

View full answer

malgates · 2024-11-12T21:19:36Z

malgates
Nov 12, 2024
Author

In Home Assistant I am getting this message:

NSPanel TFT Display Needs Update
The TFT version on your NSPanel is outdated for the panel ns-panel-wei (nspanelwhite).

Current TFT version: 000.000
Expected version: 4.3.12
How to Resolve This Issue

Navigate to the [device page](https://ha.lucas.com.de/config/devices/device/dbba2964998211379da14badd986ec7e).
In the "Configuration" section, find the option labeled "Update TFT Display - Model".
Click "Update TFT Display" to initiate the update process.
Please wait patiently until your panel restarts, indicating the update is complete.

For more detailed instructions, please refer to the online documentation: How to Update TFT.

No success ....

0 replies

malgates · 2024-11-12T21:23:01Z

malgates
Nov 12, 2024
Author

those are the logs when pressing the "update TFT" button:

[22:21:24][D][button:010]: 'Update TFT display' Pressed.
[22:21:26][D][addon_upload_tft.script.open_upload_dialog:134]: Showing upload dialog page
[22:21:26][W][nextion:392]: Nextion reported page ID invalid!
[22:21:28][W][nextion:431]: Nextion reported variable name invalid!
[22:21:28][D][sensor:094]: 'ntc_source': Sending state 1.74583 V with 2 decimals of accuracy
[22:21:28][D][resistance:039]: 'resistance_sensor' - Resistance 12581.2Ω
[22:21:28][D][sensor:094]: 'resistance_sensor': Sending state 12581.23340 Ω with 1 decimals of accuracy
[22:21:28][D][ntc:026]: 'Temperature' - Temperature: 19.9°C
[22:21:28][D][sensor:094]: 'Temperature': Sending state 19.92049 °C with 1 decimals of accuracy
[22:21:28][D][climate:396]: 'Thermostat' - Sending state:
[22:21:28][D][climate:399]: Mode: OFF
[22:21:28][D][climate:401]: Action: OFF
[22:21:28][D][climate:419]: Current Temperature: 19.92°C
[22:21:28][D][climate:425]: Target Temperature: 22.00°C
[22:21:28][W][nextion:431]: Nextion reported variable name invalid!
[22:21:28][W][nextion:431]: Nextion reported variable name invalid!
[22:21:28][W][nextion:431]: Nextion reported variable name invalid!
[22:21:28][W][nextion:431]: Nextion reported variable name invalid!
[22:21:28][W][nextion:431]: Nextion reported variable name invalid!
[22:21:29][W][nextion:431]: Nextion reported variable name invalid!
[22:21:30][D][addon_upload_tft.script.report_upload_progress:158]: Set Nextion unavailable for blueprint calls
[22:21:30][D][binary_sensor:036]: 'Nextion display': Sending state OFF
[22:21:30][D][addon_upload_tft.script.report_upload_progress:158]: Preparing for upload...
[22:21:30][D][script.nextion_status:107]: Nextion status:
[22:21:30][D][script.nextion_status:108]: Is detected: YES
[22:21:30][D][script.nextion_status:109]: Is setup: YES
[22:21:30][D][script.nextion_status:110]: Queue size: 0
[22:21:30][D][addon_upload_tft.script.upload_tft:220]: Starting the upload script
[22:21:30][D][addon_upload_tft.script.upload_tft:221]: Valid TFT: NO
[22:21:30][D][addon_upload_tft.script.upload_tft:222]: Current baud rate: 115200 bps
[22:21:30][D][addon_upload_tft.script.upload_tft:223]: Target upload baud rate: 921600 bps
[22:21:30][D][addon_upload_tft.script.upload_tft:224]: Upload URL: https://raw.githubusercontent.com/Blackymas/NSPanel_HA_Blueprint/v4.3.12/hmi/nspanel_eu.tft
[22:21:32][D][addon_upload_tft.script.open_upload_dialog:134]: Showing upload dialog page
[22:21:32][W][nextion:392]: Nextion reported page ID invalid!
[22:21:34][D][text_sensor:064]: 'Device Name': Sending state 'nspanelwhite'
[22:21:34][W][nextion:431]: Nextion reported variable name invalid!
[22:21:36][D][addon_upload_tft.script.report_upload_progress:158]: Stopping other scripts
[22:21:36][D][script.nextion_status:107]: Nextion status:
[22:21:36][D][script.nextion_status:108]: Is detected: YES
[22:21:36][D][script.nextion_status:109]: Is setup: YES
[22:21:36][D][script.nextion_status:110]: Queue size: 0
[22:21:36][D][addon_upload_tft.script.report_upload_progress:158]: Setting baud rate
[22:21:36][D][script.set_baud_rate:3022]: Baud rate changing from 115200 to 921600 bps
[22:21:36][D][script.set_baud_rate:3023]: Flush UART
[22:21:36][D][script.set_baud_rate:3029]: Sending instruction 'baud=921600' to Nextion
[22:21:36][D][script.set_baud_rate:3031]: Flush UART
[22:21:36][D][script.set_baud_rate:3037]: Set ESPHome new baud rate to 921600 bps
[22:21:36][C][uart.idf:153]: UART 0 was reloaded.
[22:21:36][C][uart.idf:159]: UART Bus 0:
[22:21:36][C][uart.idf:160]: TX Pin: GPIO16
[22:21:36][C][uart.idf:161]: RX Pin: GPIO17
[22:21:36][C][uart.idf:163]: RX Buffer Size: 256
[22:21:36][D][sensor:094]: 'RSSI': Sending state -56.00000 dBm with 0 decimals of accuracy
[22:21:38][D][main:403]: Attempting to upload TFT
[22:21:38][D][addon_upload_tft.script.report_upload_progress:158]: Attempt #1 at 921600 bps
[22:21:38][D][addon_upload_tft.script.nextion_upload:118]: Waiting for empty UART and Nextion queues
[22:21:38][D][sensor:094]: 'ntc_source': Sending state 1.74600 V with 2 decimals of accuracy
[22:21:38][D][resistance:039]: 'resistance_sensor' - Resistance 12583.8Ω
[22:21:38][D][sensor:094]: 'resistance_sensor': Sending state 12583.78320 Ω with 1 decimals of accuracy
[22:21:38][D][ntc:026]: 'Temperature' - Temperature: 19.9°C
[22:21:38][D][sensor:094]: 'Temperature': Sending state 19.91608 °C with 1 decimals of accuracy
[22:21:38][D][climate:396]: 'Thermostat' - Sending state:
[22:21:38][D][climate:399]: Mode: OFF
[22:21:38][D][climate:401]: Action: OFF
[22:21:38][D][climate:419]: Current Temperature: 19.92°C
[22:21:38][D][climate:425]: Target Temperature: 22.00°C
[22:21:38][W][nextion:431]: Nextion reported variable name invalid!
[22:21:40][D][addon_upload_tft.script.nextion_upload:126]: Starting TFT upload...
[22:21:40][D][nextion.upload.idf:157]: Nextion TFT upload requested
[22:21:40][D][nextion.upload.idf:158]: Exit reparse: NO
[22:21:40][D][nextion.upload.idf:159]: URL: https://raw.githubusercontent.com/Blackymas/NSPanel_HA_Blueprint/v4.3.12/hmi/nspanel_eu.tft
[22:21:40][D][nextion.upload.idf:188]: Baud rate: 921600
WARNING nspanelwhite @ 192.168.1.123: Connection error occurred: [Errno 104] Connection reset by peer
INFO Processing unexpected disconnect from ESPHome API for nspanelwhite @ 192.168.1.123
WARNING Disconnected from API
INFO Successfully connected to nspanelwhite @ 192.168.1.123 in 0.091s
INFO Successful handshake with nspanelwhite @ 192.168.1.123 in 0.116s
[22:22:19][W][nextion:091]: Nextion is not connected!
[22:22:20][W][nextion:091]: Nextion is not connected!
[22:22:20][W][nextion:091]: Nextion is not connected!
[22:22:21][W][nextion:091]: Nextion is not connected!
[22:22:21][W][nextion:091]: Nextion is not connected!
[22:22:22][W][nextion:091]: Nextion is not connected!
[22:22:22][W][nextion:091]: Nextion is not connected!
[22:22:23][W][nextion:091]: Nextion is not connected!
[22:22:23][W][nextion:091]: Nextion is not connected!
[22:22:24][D][sensor:094]: 'ntc_source': Sending state 1.74600 V with 2 decimals of accuracy
[22:22:24][D][resistance:039]: 'resistance_sensor' - Resistance 12583.8Ω
[22:22:24][D][sensor:094]: 'resistance_sensor': Sending state 12583.78320 Ω with 1 decimals of accuracy
[22:22:24][D][ntc:026]: 'Temperature' - Temperature: 19.9°C
[22:22:24][D][sensor:094]: 'Temperature': Sending state 19.91608 °C with 1 decimals of accuracy
[22:22:24][D][climate:396]: 'Thermostat' - Sending state:
[22:22:24][D][climate:399]: Mode: OFF
[22:22:24][D][climate:401]: Action: OFF
[22:22:24][D][climate:419]: Current Temperature: 19.92°C
[22:22:24][D][climate:425]: Target Temperature: 22.00°C
[22:22:24][W][nextion:091]: Nextion is not connected!
[22:22:24][W][nextion:091]: Nextion is not connected!
[22:22:25][W][nextion:091]: Nextion is not connected!
[22:22:25][W][nextion:091]: Nextion is not connected!
[22:22:26][W][nextion:091]: Nextion is not connected!
[22:22:26][W][nextion:091]: Nextion is not connected!
[22:22:27][W][nextion:091]: Nextion is not connected!
[22:22:27][W][nextion:091]: Nextion is not connected!
[22:22:28][W][nextion:091]: Nextion is not connected!
[22:22:28][W][nextion:091]: Nextion is not connected!
[22:22:29][C][nspanel_ha_blueprint:2224]: Wi-Fi: Good (-57 dBm)
[22:22:29][C][nspanel_ha_blueprint:2235]: API: Connected
[22:22:29][C][nspanel_ha_blueprint:2243]: Blueprint:
[22:22:29][W][nspanel_ha_blueprint:2248]: Init steps: 0 (0.0%)
[22:22:29][W][nspanel_ha_blueprint:2249]: State: Pending
[22:22:29][C][nspanel_ha_blueprint:2250]: Requesting blueprint settings
[22:22:29][D][script:077]: Script 'boot_event' restarting (mode: restart)
[22:22:29][C][nspanel_ha_blueprint:2255]: ESPHome:
[22:22:29][C][nspanel_ha_blueprint:2256]: Version: 4.3.12
[22:22:29][C][nspanel_ha_blueprint:2257]: Compiler: 2024.10.2
[22:22:29][C][nspanel_ha_blueprint:2262]: Framework: ESP-IDF
[22:22:29][C][nspanel_ha_blueprint:2267]: Free heap:
[22:22:29][C][nspanel_ha_blueprint:2271]: Internal: 197268 bytes (56.2%)
[22:22:29][C][nspanel_ha_blueprint:2281]: PSRAM: 1973083 bytes (94.6%)
[22:22:29][W][nextion:091]: Nextion is not connected!

14 replies

malgates Nov 13, 2024
Author

So I have pihole up and running, but I looked in the logs and it does not seem to block it. Regarding wifi: the access point is only 3m away in viewing distance.

Will try another spot though

Can I redirect the file to a local Server?

malgates Nov 13, 2024
Author

I have a 2nd NSPanel, which is operational for quite some time. I tried to update the TFT, just to see if it works as well. This is what I got. Seems I do have a connection problem:

[22:01:09][D][button:010]: 'Update TFT display' Pressed.
[22:01:09][D][text_sensor:064]: 'Current Page': Sending state 'home'
[22:01:09][D][script.page_changed:2644]: New page: home
[22:01:09][D][text_sensor:064]: 'Detailed Entity': Sending state ''
[22:01:09][D][script.timer_dim:3271]: Waking up on page: home
[22:01:09][D][nextion_textsensor:014]: Processed text_sensor "current_page" state "home"
[22:01:10][D][sensor:094]: 'Display Current brightness': Sending state 100.00000 % with 0 decimals of accuracy
[22:01:11][D][addon_upload_tft.script.open_upload_dialog:134]: Showing upload dialog page
[22:01:11][D][text_sensor:064]: 'Current Page': Sending state 'confirm'
[22:01:11][D][script.page_changed:2644]: New page: confirm
[22:01:11][D][script:077]: Script 'timer_dim' restarting (mode: restart)
[22:01:11][D][script:077]: Script 'timer_sleep' restarting (mode: restart)
[22:01:11][D][nextion_textsensor:014]: Processed text_sensor "current_page" state "confirm"
[22:01:11][D][addon_upload_tft.script.report_upload_progress:158]: Set Nextion unavailable for blueprint calls
[22:01:11][D][binary_sensor:036]: 'Nextion display': Sending state OFF
[22:01:11][D][addon_upload_tft.script.report_upload_progress:158]: Preparing for upload...
[22:01:11][D][script.nextion_status:107]: Nextion status:
[22:01:11][D][script.nextion_status:108]: Is detected: YES
[22:01:11][D][script.nextion_status:109]: Is setup: YES
[22:01:11][D][script.nextion_status:110]: Queue size: 13
[22:01:11][D][addon_upload_tft.script.upload_tft:220]: Starting the upload script
[22:01:11][D][addon_upload_tft.script.upload_tft:221]: Valid TFT: YES
[22:01:16][D][addon_upload_tft.script.upload_tft:222]: Current baud rate: 115200 bps
[22:01:16][D][main:403]: Attempting to upload TFT
[22:01:16][D][addon_upload_tft.script.report_upload_progress:158]: Attempt #1 at 921600 bps
[22:01:17][D][addon_upload_tft.script.nextion_upload:118]: Waiting for empty UART and Nextion queues
[22:01:18][D][sensor:094]: 'ntc_source': Sending state 1.67733 V with 2 decimals of accuracy
[22:01:18][D][resistance:039]: 'resistance_sensor' - Resistance 11577.3Ω
[22:01:18][D][sensor:094]: 'resistance_sensor': Sending state 11577.31934 Ω with 1 decimals of accuracy
[22:01:18][D][ntc:026]: 'Temperature' - Temperature: 21.7°C
[22:01:18][D][sensor:094]: 'Temperature': Sending state 21.73994 °C with 1 decimals of accuracy
[22:01:18][D][climate:396]: 'Thermostat' - Sending state:
[22:01:18][D][climate:399]: Mode: HEAT
[22:01:18][D][climate:401]: Action: IDLE
[22:01:18][D][climate:419]: Current Temperature: 21.74°C
[22:01:18][D][climate:425]: Target Temperature: 21.80°C
[22:01:22][D][nextion:796]: Removing old queue type "NO_RESULT" name "set_component_text"
[22:01:22][D][nextion:796]: Removing old queue type "NO_RESULT" name "backlight_brightness"
[22:01:22][D][nextion:796]: Removing old queue type "NO_RESULT" name "send_command_printf"
[22:01:24][D][nextion:796]: Removing old queue type "NO_RESULT" name "set_component_text"
[22:01:24][D][nextion:796]: Removing old queue type "NO_RESULT" name "backlight_brightness"
[22:01:24][D][esp32.preferences:114]: Saving 1 preferences to flash...
[22:01:24][D][esp32.preferences:143]: Saving 1 preferences to flash: 1 cached, 0 written, 0 failed
[22:01:26][D][nextion:796]: Removing old queue type "NO_RESULT" name "set_component_text"
[22:01:28][D][sensor:094]: 'ntc_source': Sending state 1.67817 V with 2 decimals of accuracy
[22:01:28][D][resistance:039]: 'resistance_sensor' - Resistance 11589.0Ω
[22:01:28][D][sensor:094]: 'resistance_sensor': Sending state 11589.02637 Ω with 1 decimals of accuracy
[22:01:28][D][ntc:026]: 'Temperature' - Temperature: 21.7°C
[22:01:28][D][sensor:094]: 'Temperature': Sending state 21.71769 °C with 1 decimals of accuracy
[22:01:28][D][climate:396]: 'Thermostat' - Sending state:
[22:01:28][D][climate:399]: Mode: HEAT
[22:01:28][D][climate:401]: Action: IDLE
[22:01:28][D][climate:419]: Current Temperature: 21.72°C
[22:01:28][D][climate:425]: Target Temperature: 21.80°C
[22:01:28][D][addon_upload_tft.script.nextion_upload:126]: Starting TFT upload...
[22:01:28][D][nextion.upload.idf:157]: Nextion TFT upload requested
[22:01:28][D][nextion.upload.idf:158]: Exit reparse: NO
[22:01:28][D][nextion.upload.idf:159]: URL: https://raw.githubusercontent.com/Blackymas/NSPanel_HA_Blueprint/v4.3.12/hmi/nspanel_eu.tft
[22:01:28][D][nextion.upload.idf:188]: Baud rate: 921600
WARNING nspanelwozi @ 192.168.1.196: Connection error occurred: [Errno 104] Connection reset by peer
INFO Processing unexpected disconnect from ESPHome API for nspanelwozi @ 192.168.1.196
WARNING Disconnected from API
INFO Successfully connected to nspanelwozi @ 192.168.1.196 in 2.996s
INFO Successful handshake with nspanelwozi @ 192.168.1.196 in 0.049s
[22:02:07][D][script.boot_log:2048]: Jump to wake-up page
[22:02:07][D][script.page_boot:2606]: Jump to wake-up page: home
[22:02:07][D][sensor:094]: 'Display Current brightness': Sending state 100.00000 % with 0 decimals of accuracy
[22:02:07][D][text_sensor:064]: 'Current Page': Sending state 'home'
[22:02:07][D][script.page_changed:2644]: New page: home
[22:02:07][D][text_sensor:064]: 'Detailed Entity': Sending state ''
[22:02:07][D][script:077]: Script 'timer_dim' restarting (mode: restart)
[22:02:07][D][nextion_textsensor:014]: Processed text_sensor "current_page" state "home"
[22:02:11][D][text_sensor:064]: 'Device Name': Sending state 'nspanelwozi'
[22:02:14][D][esp32.preferences:114]: Saving 1 preferences to flash...
[22:02:14][D][esp32.preferences:143]: Saving 1 preferences to flash: 1 cached, 0 written, 0 failed
[22:02:14][D][sensor:094]: 'ntc_source': Sending state 1.67700 V with 2 decimals of accuracy
[22:02:14][D][resistance:039]: 'resistance_sensor' - Resistance 11572.6Ω
[22:02:14][D][sensor:094]: 'resistance_sensor': Sending state 11572.64453 Ω with 1 decimals of accuracy
[22:02:14][D][ntc:026]: 'Temperature' - Temperature: 21.7°C
[22:02:14][D][sensor:094]: 'Temperature': Sending state 21.74883 °C with 1 decimals of accuracy
[22:02:14][D][climate:396]: 'Thermostat' - Sending state:
[22:02:14][D][climate:399]: Mode: HEAT
[22:02:14][D][climate:401]: Action: IDLE
[22:02:14][D][climate:419]: Current Temperature: 21.75°C
[22:02:14][D][climate:425]: Target Temperature: 21.80°C
[22:02:17][C][nspanel_ha_blueprint:2224]: Wi-Fi: Good (-56 dBm)
[22:02:17][C][nspanel_ha_blueprint:2235]: API: Connected
[22:02:17][C][nspanel_ha_blueprint:2243]: Blueprint:
[22:02:17][W][nspanel_ha_blueprint:2248]: Init steps: 0 (0.0%)
[22:02:17][W][nspanel_ha_blueprint:2249]: State: Pending
[22:02:17][C][nspanel_ha_blueprint:2250]: Requesting blueprint settings
[22:02:17][D][script:077]: Script 'boot_event' restarting (mode: restart)
[22:02:17][C][nspanel_ha_blueprint:2255]: ESPHome:
[22:02:17][C][nspanel_ha_blueprint:2256]: Version: 4.3.12
[22:02:17][C][nspanel_ha_blueprint:2257]: Compiler: 2024.10.2
[22:02:17][C][nspanel_ha_blueprint:2262]: Framework: ESP-IDF
[22:02:17][C][nspanel_ha_blueprint:2267]: Free heap:
[22:02:17][C][nspanel_ha_blueprint:2271]: Internal: 201672 bytes (57.4%)
[22:02:17][C][nspanel_ha_blueprint:2281]: PSRAM: 2018143 bytes (96.8%)
[22:02:17][C][nspanel_ha_blueprint:2288]: UART:
[22:02:17][C][nspanel_ha_blueprint:2289]: Baud rate: 115200 bps
[22:02:17][C][nspanel_ha_blueprint:2290]: Queue size: 0
[22:02:17][C][nspanel_ha_blueprint:2294]: Nextion:
[22:02:17][C][nspanel_ha_blueprint:2295]: Queue size: 0
[22:02:17][C][nspanel_ha_blueprint:2297]: Is setup: True
[22:02:17][C][nspanel_ha_blueprint:2304]: Init: True
[22:02:17][C][nspanel_ha_blueprint:2310]: TFT: 4.3.11
[22:02:17][C][nspanel_ha_blueprint:2311]: Packages:
[22:02:17][C][nspanel_ha_blueprint:2313]: - Core
[22:02:17][C][nspanel_ha_blueprint:2322]: - Upload TFT
[22:02:17][C][nspanel_ha_blueprint:2325]: - Climate - Base
[22:02:17][C][nspanel_ha_blueprint:2334]: - Climate - Heat
[22:02:17][C][nspanel_ha_blueprint:097]: Add-on Upload TFT:
[22:02:17][C][nspanel_ha_blueprint:098]: File model: NSPanel EU
[22:02:17][C][nspanel_ha_blueprint:099]: Valid TFT: YES
[22:02:17][C][nspanel_ha_blueprint:133]: Add-on climate:
[22:02:17][C][nspanel_ha_blueprint:142]: Heat: Enabled
[22:02:17][C][nspanel_ha_blueprint:144]: Relay: 1
[22:02:17][W][component:237]: Component script took a long time for an operation (54 ms).
[22:02:17][W][component:238]: Components should block for at most 30 ms.
[22:02:24][D][sensor:094]: 'ntc_source': Sending state 1.67600 V with 2 decimals of accuracy
[22:02:24][D][resistance:039]: 'resistance_sensor' - Resistance 11558.6Ω
[22:02:24][D][sensor:094]: 'resistance_sensor': Sending state 11558.62109 Ω with 1 decimals of accuracy
[22:02:24][D][ntc:026]: 'Temperature' - Temperature: 21.8°C
[22:02:24][D][sensor:094]: 'Temperature': Sending state 21.77553 °C with 1 decimals of accuracy
[22:02:24][D][climate:396]: 'Thermostat' - Sending state:
[22:02:24][D][climate:399]: Mode: HEAT
[22:02:24][D][climate:401]: Action: IDLE
[22:02:24][D][climate:419]: Current Temperature: 21.78°C
[22:02:24][D][climate:425]: Target Temperature: 21.80°C
[22:02:33][I][script.set_timezone:3151]: Setting timezone: CET-1CEST,M3.5.0,M10.5.0/3
[22:02:33][C][homeassistant.time:010]: Home Assistant Time:
[22:02:33][C][homeassistant.time:011]: Timezone: 'CET-1CEST,M3.5.0,M10.5.0/3'
[22:02:33][W][nextion:431]: Nextion reported variable name invalid!
[22:02:33][D][script.boot_log:2048]: init_page_home
[22:02:33][D][sensor:094]: 'Blueprint': Sending state 3.22581 % with 1 decimals of accuracy
[22:02:33][W][component:237]: Component api took a long time for an operation (68 ms).
[22:02:33][W][component:238]: Components should block for at most 30 ms.
[22:02:33][D][sensor:094]: 'RSSI': Sending state -56.00000 dBm with 0 decimals of accuracy
[22:02:34][D][sensor:094]: 'ntc_source': Sending state 1.67567 V with 2 decimals of accuracy
[22:02:34][D][resistance:039]: 'resistance_sensor' - Resistance 11554.0Ω
[22:02:34][D][sensor:094]: 'resistance_sensor': Sending state 11553.95117 Ω with 1 decimals of accuracy
[22:02:34][D][ntc:026]: 'Temperature' - Temperature: 21.8°C
[22:02:34][D][sensor:094]: 'Temperature': Sending state 21.78443 °C with 1 decimals of accuracy
[22:02:34][D][climate:396]: 'Thermostat' - Sending state:
[22:02:34][D][climate:399]: Mode: HEAT
[22:02:34][D][climate:401]: Action: IDLE
[22:02:34][D][climate:419]: Current Temperature: 21.78°C
[22:02:34][D][climate:425]: Target Temperature: 21.80°C
[22:02:35][I][safe_mode:041]: Boot seems successful; resetting boot loop counter

edwardtfn Nov 13, 2024
Collaborator

So I have pihole up and running, but I looked in the logs and it does not seem to block it. Regarding wifi: the access point is only 3m away in viewing distance.

I have a 2nd NSPanel, which is operational for quite some time. I tried to update the TFT, just to see if it works as well. This is what I got. Seems I do have a connection problem:

If you haven't disabled DNS in your router, try to set dns1: 192.168.1.1 and give it a try.

Can I redirect the file to a local Server?

Yes. You can set the substitution nextion_update_base_url to a local server where your file is located (please keep file name unchanged).
It's default is the GitHub server:

substitutions:
  nextion_update_base_url: "https://raw.githubusercontent.com/Blackymas/NSPanel_HA_Blueprint/"

malgates Nov 13, 2024
Author

OK I officially had a DNS problem. THANKS for pointing that out! BOG THX for the help!

I was able to flash the NSPanel Blank. Currently trying the EU one.

Answer selected by malgates

edwardtfn Nov 13, 2024
Collaborator

I have to work on the Nextion component on ESPHome to make it more resilient to DNS issues. It shouldn't crash, but log an error message, ideally saying what was wrong.

malgates Nov 14, 2024
Author

hard to log it. Seems like PiHole did not throw an error. I added the Google DNS and DNS.WATCH and that solved it.

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

System Data Error! #2377

{{title}}

{{editor}}'s edit

{{editor}}'s edit

Replies: 2 comments 14 replies

{{title}}

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{title}}

Select a reply

System Data Error! #2377

malgates Nov 12, 2024

Replies: 2 comments · 14 replies

malgates Nov 12, 2024 Author

malgates Nov 12, 2024 Author

malgates Nov 13, 2024 Author

malgates Nov 13, 2024 Author

edwardtfn Nov 13, 2024 Collaborator

malgates Nov 13, 2024 Author

edwardtfn Nov 13, 2024 Collaborator

malgates Nov 14, 2024 Author

malgates
Nov 12, 2024

Replies: 2 comments 14 replies

malgates
Nov 12, 2024
Author

malgates
Nov 12, 2024
Author

malgates Nov 13, 2024
Author

malgates Nov 13, 2024
Author

edwardtfn Nov 13, 2024
Collaborator

malgates Nov 13, 2024
Author

edwardtfn Nov 13, 2024
Collaborator

malgates Nov 14, 2024
Author