diff --git a/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/defaults.parm b/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/defaults.parm new file mode 100644 index 0000000000000..0a0a6b14ae7ff --- /dev/null +++ b/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/defaults.parm @@ -0,0 +1,27 @@ +ARSPD_TYPE 15 +BATT_VOLT_PIN 19 +BATT_VOLT_MULT 21 +BATT_MONITOR 3 +CAN_P1_DRIVER 1 + +SERIAL1_BAUD 115 +SERIAL1_PROTOCOL 16 + +SERIAL2_BAUD 115 +SERIAL2_PROTOCOL -1 + +SERIAL3_BAUD 115 +SERIAL3_PROTOCOL -1 + +SERIAL4_BAUD 115 +SERIAL4_PROTOCOL -1 + +SERIAL5_BAUD 230 +SERIAL5_PROTOCOL 5 + +SERIAL6_BAUD 115 +SERIAL6_PROTOCOL 2 + +SERIAL7_BAUD 115 +SERIAL7_PROTOCOL 23 + diff --git a/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/hwdef-bl.dat b/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/hwdef-bl.dat new file mode 100644 index 0000000000000..8dc46602a3510 --- /dev/null +++ b/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/hwdef-bl.dat @@ -0,0 +1,53 @@ +# MCU class and specific type +MCU STM32H7xx STM32H743xx + +# crystal frequency +OSCILLATOR_HZ 24000000 + +# board ID for firmware load +APJ_BOARD_ID 140 + +FLASH_SIZE_KB 2048 + +# bootloader is installed at zero offset +FLASH_RESERVE_START_KB 0 + +# the location where the bootloader will put the firmware +# the H743 has 128k sectors +FLASH_BOOTLOADER_LOAD_KB 128 + +#define LED pins +PE14 LED_BOOTLOADER OUTPUT OPENDRAIN HIGH # red +PE12 LED_ACTIVITY OUTPUT OPENDRAIN HIGH # green +PE13 LED_RED OUTPUT OPENDRAIN HIGH # blue + +# order of UARTs (and USB) +SERIAL_ORDER OTG1 USART1 + +# UART1 is debug +PA9 USART1_TX USART1 NODMA +PA10 USART1_RX USART1 NODMA + +PC13 VDD_3V3_SENSORS_EN OUTPUT LOW OPENDRAIN +PC4 nVDD_5V_PERIPH_EN OUTPUT HIGH OPENDRAIN +PE8 nVDD_12V_PERIPH_EN OUTPUT LOW OPENDRAIN + +PA11 OTG_FS_DM OTG1 +PA12 OTG_FS_DP OTG1 + +PA13 JTMS-SWDIO SWD +PA14 JTCK-SWCLK SWD + +define HAL_USE_EMPTY_STORAGE 1 +define HAL_STORAGE_SIZE 32768 +define HAL_LED_ON 1 + +# define BOOTLOADER_DEBUG SD7 + +# Add CS pins to ensure they are high in bootloader +PD7 16470_CS CS +PD4 42688_1_CS CS +PC15 42688_2_CS CS + +PD10 FRAM_CS CS SPEED_VERYLOW +PC14 FLASH_CS CS \ No newline at end of file diff --git a/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/hwdef.dat b/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/hwdef.dat new file mode 100644 index 0000000000000..e0bcee476643b --- /dev/null +++ b/libraries/AP_HAL_ChibiOS/hwdef/AEROFOX-H7/hwdef.dat @@ -0,0 +1,225 @@ +# MCU class and specific type +MCU STM32H7xx STM32H743xx + +# crystal frequency +OSCILLATOR_HZ 24000000 + +# board ID for firmware load +APJ_BOARD_ID 7200 + +FLASH_SIZE_KB 2048 + +# bootloader is installed at zero offset +FLASH_RESERVE_START_KB 128 + +# UART1 is debug +PA9 USART1_TX USART1 NODMA +PA10 USART1_RX USART1 NODMA + +PA11 OTG_FS_DM OTG1 +PA12 OTG_FS_DP OTG1# crystal frequency + +# supports upto 8MBits/s +CANFD_SUPPORTED 8 + +# with 2M flash we can afford to optimize for speed +env OPTIMIZE -O2 + +# system timer +STM32_ST_USE_TIMER 5 + +# UART +SERIAL_ORDER OTG1 UART7 UART4 UART5 USART2 USART1 UART8 USART3 OTG2 + +#serial1 +PA15 UART7_TX UART7 +PA8 UART7_RX UART7 + +# serial2 +PC10 UART4_TX UART4 +PC11 UART4_RX UART4 + +# serial3 +PC12 UART5_TX UART5 +PD2 UART5_RX UART5 + +# serial4 +PD5 USART2_TX USART2 +PD6 USART2_RX USART2 + +# serial6 +PE1 UART8_TX UART8 +PE0 UART8_RX UART8 + +# serial7 +PD8 USART3_TX USART3 +PD9 USART3_RX USART3 + +# default the 2nd interface to SLCAN +define HAL_OTG2_PROTOCOL SerialProtocol_SLCAN + +# CAN +PD0 CAN1_RX CAN1 +PD1 CAN1_TX CAN1 + +PB12 CAN2_RX CAN2 +PB13 CAN2_TX CAN2 + +# I2C +I2C_ORDER I2C1 I2C2 + +PB6 I2C1_SCL I2C1 +PB7 I2C1_SDA I2C1 + +PB10 I2C2_SCL I2C2 +PB11 I2C2_SDA I2C2 + +# SPI +PB3 SPI1_SCK SPI1 +PB4 SPI1_MISO SPI1 +PB5 SPI1_MOSI SPI1 + +PD3 SPI2_SCK SPI2 +PC2 SPI2_MISO SPI2 +PC3 SPI2_MOSI SPI2 + +PE2 SPI4_SCK SPI4 +PE5 SPI4_MISO SPI4 +PE6 SPI4_MOSI SPI4 + +# IMU +IMU ADIS1647x SPI:16470 ROTATION_PITCH_180 ADIS_DRDY_PIN +IMU Invensensev3 SPI:42688_1 ROTATION_NONE +IMU Invensensev3 SPI:42688_2 ROTATION_PITCH_180_YAW_270 + +SPIDEV 16470 SPI1 DEVID1 16470_CS MODE3 1*MHZ 2*MHZ +SPIDEV 42688_1 SPI1 DEVID2 42688_1_CS MODE3 2*MHZ 8*MHZ +SPIDEV 42688_2 SPI4 DEVID3 42688_2_CS MODE3 2*MHZ 8*MHZ + +SPIDEV ramtron SPI2 DEVID1 FRAM_CS MODE3 8*MHZ 8*MHZ +SPIDEV sdcard SPI2 DEVID2 FLASH_CS MODE0 1*MHZ 8*MHZ + +PD7 16470_CS CS +PD4 42688_1_CS CS +PC15 42688_2_CS CS + +PD10 FRAM_CS CS SPEED_VERYLOW +PC14 FLASH_CS CS + +PE7 DRDY1_ADIS16470 INPUT GPIO(90) +define ADIS_DRDY_PIN 90 + +# ADC +PA5 BATT_VOLTAGE_SENS ADC1 SCALE(1) +PB0 BATT_CURRENT_SENS ADC1 SCALE(1) + +PC0 BATT2_VOLTAGE_SENS ADC1 SCALE(1) +PC1 BATT2_CURRENT_SENS ADC1 SCALE(1) + +PB1 FMU_SERVORAIL_VCC_SENS ADC1 SCALE(12) +PA4 VDD_5V_SENS ADC1 SCALE(2) + +# GPIO +PA0 TIM2_CH1 TIM2 PWM(1) GPIO(50) +PA1 TIM2_CH2 TIM2 PWM(2) GPIO(51) +PE9 TIM1_CH1 TIM1 PWM(3) GPIO(52) +PE11 TIM1_CH2 TIM1 PWM(4) GPIO(53) +PD12 TIM4_CH1 TIM4 PWM(5) GPIO(54) +PD13 TIM4_CH2 TIM4 PWM(6) GPIO(55) +PC6 TIM3_CH1 TIM3 PWM(7) GPIO(56) +PC7 TIM3_CH2 TIM3 PWM(8) GPIO(57) + +PA2 TIM15_CH1 TIM15 PWM(9) GPIO(58) +PA3 TIM15_CH2 TIM15 PWM(10) GPIO(59) +PA7 TIM14_CH1 TIM14 PWM(11) GPIO(60) +PA6 TIM13_CH1 TIM13 PWM(12) GPIO(61) +PC9 TIM8_CH4 TIM8 PWM(13) GPIO(62) +PC8 TIM8_CH3 TIM8 PWM(14) GPIO(63) +PB15 TIM12_CH2 TIM12 PWM(15) GPIO(64) +PB14 TIM12_CH1 TIM12 PWM(16) GPIO(65) + +PB9 TIM17_CH1 TIM17 ALARM + +PE3 EXTERN_GPIO1 OUTPUT GPIO(1) +PE4 EXTERN_GPIO2 OUTPUT GPIO(2) +PD11 EXTERN_GPIO3 OUTPUT GPIO(3) +#PD14 EXTERN_GPIO4 OUTPUT GPIO(4) + +PD14 LED_SAFETY OUTPUT +PD15 SAFETY_IN INPUT PULLDOWN + +PC13 VDD_3V3_SENSORS_EN OUTPUT LOW OPENDRAIN +PC4 nVDD_5V_PERIPH_EN OUTPUT LOW OPENDRAIN +PE8 nVDD_12V_PERIPH_EN OUTPUT HIGH OPENDRAIN + +PE10 VDD_5V_HIPOWER_oOC INPUT PULLUP +PC5 VDD_BRICK_nVALID INPUT PULLUP + +# BARO +BARO SPL06 I2C:0:0x76 +define AP_BACKEDN_DEFAULT_ENABLE 0 +define AP_BARO_SPL06_ENABLE 1 + +# COMPASS +COMPASS QMC5883L I2C:0:0x0D false ROTATION_NONE + +# LED setup is similar to PixRacer + +define AP_NOTIFY_GPIO_LED_RGB_ENABLED 1 +PE14 LED_RED OUTPUT GPIO(10) +PE12 LED_GREEN OUTPUT GPIO(11) +PE13 LED_BLUE OUTPUT GPIO(12) + +define AP_NOTIFY_GPIO_LED_RGB_RED_PIN 10 +define AP_NOTIFY_GPIO_LED_RGB_GREEN_PIN 11 +define AP_NOTIFY_GPIO_LED_RGB_BLUE_PIN 12 + + +# IMU heater +PB8 HEATER_EN OUTPUT LOW GPIO(80) +define HAL_HEATER_GPIO_PIN 80 +define HAL_HAVE_IMU_HEATER 1 +define HAL_IMU_TEMP_DEFAULT 35 +define HAL_IMUHEAT_P_DEFAULT 50 +define HAL_IMUHEAT_I_DEFAULT 0.07 +define HAL_IMU_TEMP_MARGIN_LOW_DEFAULT 5 + +# compass +define HAL_PROBE_EXTERNAL_I2C_COMPASSES + +define HAL_SKIP_AUTO_INTERNAL_I2C_PROBE + +define HAL_I2C_INTERNAL_MASK 1 + +# SWD debugging +PA13 JTMS-SWDIO SWD +PA14 JTCK-SWCLK SWD + +#include sdcard.inc + +define HAL_CHIBIOS_ARCH_FMUV3 1 + +define BOARD_TYPE_DEFAULT 3 + +# safety switch +define HAL_HAVE_SAFETY_SWITCH 1 + +# FRAM +define HAL_WITH_RAMTRON 1 +define HAL_STORAGE_SIZE 32768 + +# open all IMUs +define HAL_EKF_IMU_MASK_DEFAULT 7 + +# IMU fast sample +define HAL_DEFAULT_INS_FAST_SAMPLE 7 + +# Enable FAT +define HAL_OS_FATFS_IO 1 + +# DMA +DMA_NOSHARE SPI2* UART2* UART4* UART5* + +ENABLE_DFU_BOOT 1 + +