APPLE HOMEBRIDGE – TEMPERATURE & HUMIDITY LEVEL.ino

/* Project name: Apple Homebridge - Temperature & Humidity level  
*  Project URI: http://www.studiopieters.nl/apple-homebridge-Temperature & Humidity level/   
*  Description: Apple Homebridge - Temperature & Humidity level
*  Version: Apple homebridge - Temperature & Humidity level 1.0.3 
*  License: GNU General Public License V2 or later  */

#include <ESP8266WiFi.h>
#include <WiFiClient.h>
#include <ESP8266WebServer.h>
#include <DHT.h>
#define DHTTYPE DHT11
#define DHTPIN  2

const char* ssid     = "Your SSID";
const char* password = "Your Password";

ESP8266WebServer server(80);
 
// Initialize DHT sensor 
// NOTE: For working with a faster than ATmega328p 16 MHz Arduino chip, like an ESP8266,
// you need to increase the threshold for cycle counts considered a 1 or 0.
// You can do this by passing a 3rd parameter for this threshold.  It's a bit
// of fiddling to find the right value, but in general the faster the CPU the
// higher the value.  The default for a 16mhz AVR is a value of 6.  For an
// Arduino Due that runs at 84mhz a value of 30 works.
// This is for the ESP8266 processor on ESP-01 
DHT dht(DHTPIN, DHTTYPE, 11); // 11 works fine for ESP8266
 
float humidity, temp_c;  // Values read from sensor

// Generally, you should use "unsigned long" for variables that hold time
unsigned long previousMillis = 0;        // will store last temp was read
const long interval = 2000;              // interval at which to read sensor
 
void handle_root() {
  server.send(200, "text/plain", "Homebridge http Temperature and humidity Sensor, read from /dht");
  delay(100);
}
 
void setup(void)
{
  // You can open the Arduino IDE Serial Monitor window to see what the code is doing
  Serial.begin(115200);  // Serial connection from ESP-01 via 3.3v console cable
  dht.begin();           // initialize temperature sensor

  // Connect to WiFi network
  WiFi.begin(ssid, password);
   IPAddress ip(192, 168, 178, 60);
  IPAddress gateway(192, 168, 178, 1);
  IPAddress subnet(255, 255, 255, 0);
  WiFi.config(ip, gateway, subnet);
  Serial.print("\n\r \n\rWorking to connect");

  // Wait for connection
  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    Serial.print(".");
  }
  Serial.println("");
  Serial.println("DHT data Reading Server");
  Serial.print("Connected to ");
  Serial.println(ssid);
  Serial.print("IP address: ");
  Serial.println(WiFi.localIP());
   
  server.on("/", handle_root);
  
 server.on("/dht", [](){
    gettemperature();
    server.send(200, "text/json","{\n" "\"temperature\": "+String(temp_c)+",\n ""\"humidity\": "+String(humidity)+"" "\n}");
  });

  
  server.begin();
  Serial.println("HTTP server started");
}
 
void loop(void)
{
  server.handleClient();
} 

void gettemperature() {
  // Wait at least 2 seconds seconds between measurements.
  // if the difference between the current time and last time you read
  // the sensor is bigger than the interval you set, read the sensor
  // Works better than delay for things happening elsewhere also
  unsigned long currentMillis = millis();
 
  if(currentMillis - previousMillis >= interval) {
    // save the last time you read the sensor 
    previousMillis = currentMillis;   

    // Reading temperature for humidity takes about 250 milliseconds!
    // Sensor readings may also be up to 2 seconds 'old' (it's a very slow sensor)
    humidity = dht.readHumidity();          // Read humidity (percent)
    temp_c = dht.readTemperature(false);     // Read temperature as Fahrenheit
    // Check if any reads failed and exit early (to try again).
    if (isnan(humidity) || isnan(temp_c)) {
      Serial.println("Failed to read from DHT sensor!");
      return;
    }
  }
}